The tps65910_irq_exit() cleanup function was generating a warning from
sparse due to the lack of a prototype. This wasn't causing GCC warnings
as the driver wasn't cleaning up its IRQs on exit at all so there was no
use of an unprototyped function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a previously undefined test register and removed a
number of double-defined accessory detect registers (they are
already defined higher up in the file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TPS65912 has five GPIOs that can be configured for different
purposes.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This module controls the interrupt handling for the tps65912.
The interrupt sources can be the following:
- GPIO
- PWRON signal
- PWRHOLD signal
- Temperature detection
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The tps65912 chip is a power management IC. It contains the following
components:
- Regulators
- GPIO controller
The core driver is registered as a platform driver, it provides communication
through I2C and SPI interfaces.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x AUXADC hardware can schedule multiple conversions at once,
allowing higher performance when more than one source is in use as we
can have the hardware start new conversions without having to wait for
a register write.
Take advantage of this in the interrupt driven case, maintaining a list of
callers that are waiting for AUXADC conversions and completing them all
simultaneously. The external interface of the AUXADC is not changed so
there will be limited use of the feature immediately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensure that there's no possibility of loosing an AUXADC interrupt by reading
the conversion result in the IRQ handler when using interrupts. Otherwise
it's possible that under very heavy load a new conversion could be initiated
before the acknowledgement for a previous interrupt has happened.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use irq_allocate_desc() to get the IRQ range, which turns into a noop on
non-sparse systems. Since all existing users are non-sparse there should
be no compatibility issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow platform data to flag the touchscreen as disabled so that if the
touch driver is built in we don't end up causing lots of work by spuriously
detecting touchscreen activity on systems where it isn't in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x IRQ set_type() operation is doing a direct register write when
called but since set_type() is called with the bus lock held this isn't
legal and could cause deadlocks in the IRQ core.
Fix this by posting the updates into an array and syncing in the
bus_sync_unlock() callback.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* git://git.infradead.org/battery-2.6:
gpio-charger: Fix checking return value of request_any_context_irq
power_supply: MAX17042: Support additional properties
max8903_charger: Allow platform data to be __initdata
power_supply: Add charger driver for MAX8998/LP3974
power_supply: Add charger driver for MAX8997/8966
max17042_battery: Remove obsolete cleanup for clientdata
twl4030_charger: Fix warnings
wm831x_power: Support multiple instances
wm831x_backup: Support multiple instances
apm_power: Fix style error in macros
s3c_adc_battery: Fix annotation for s3c_adc_battery_probe()
bq20z75: Enable detection after registering
bq20z75: Add support for external notification
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
smc91c92_cs.c: fix bogus compiler warning
orinoco_cs: be more careful when matching cards with ID 0x0156:0x0002
hostap_cs: support cards with "Version 01.02" as third product ID
pcmcia: add PCMCIA_DEVICE_MANF_CARD_PROD_ID3
pxa2xx pcmcia - stargate 2 use gpio array.
pcmcia: pxa2xx: remove empty socket_init / socket_resume functions.
drivers:pcmcia:soc_common: make socket_init and socket_suspend optional
Call GETDEVICELIST during mount, then call and parse GETDEVICEINFO
for each device returned.
[pnfsblock: get rid of deprecated xdr macros]
Signed-off-by: Jim Rees <rees@umich.edu>
[pnfsblock: fix pnfs_deviceid references]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
[pnfsblock: fix print format warnings for sector_t and size_t]
[pnfs-block: #include <linux/vmalloc.h>]
[pnfsblock: no PNFS_NFS_SERVER]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
[pnfsblock: fix bug determining size of striped volume]
[pnfsblock: fix oops when using multiple devices]
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
[pnfsblock: get rid of vmap and deviceid->area structure]
Signed-off-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This gives layout driver a chance to cleanup structures they put in at
encode_layoutcommit.
Signed-off-by: Andy Adamson <andros@netapp.com>
[fixup layout header pointer for layoutcommit]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
[rm inode and pnfs_layout_hdr args from cleanup_layoutcommit()]
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
There can be multiple lseg per file, so layoutcommit should be
able to handle it.
[Needed in v3.0]
CC: Stable Tree <stable@kernel.org>
Signed-off-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
hwmon: (lm90) Refactor reading of config2 register
hwmon: (lm90) Make SA56004 detection more robust
hwmon: (lm90) Simplify handling of extended local temp register
hwmon: (pmbus) Add client driver for LM25066, LM5064, and LM5066
hwmon: (max34440) Add support for peak attributes
hwmon: (max8688) Add support for peak attributes
hwmon: (max16064) Add support for peak attributes
hwmon: (adm1275) Add support for peak attributes
hwmon: (pmbus) Add support for peak attributes
hwmon: Add new attributes to sysfs ABI
hwmon: (pmbus) Strengthen check for status register existence
hwmon: (pmbus) Add support for virtual pages
hwmon: (pmbus) Support reading and writing of word registers in device specific code
hwmon: (pmbus) Increase attribute name size
hwmon: (pmbus) Add ADP4000, NCP4200 and NCP4208 to list of supported devices
hwmon: (pmbus) Add support for VID output voltage mode
hwmon: (pmbus) Move PMBus drivers to drivers/hwmon/pmbus
hwmon: (coretemp) Add core/pkg threshold support to Coretemp
hwmon: (lm95241) Add support for LM95231
hwmon: LM95245 driver
...
shm_try_destroy_orphaned() and shm_try_destroy_current() didn't handle
the case of separate PID namespaces, but a single IPC namespace. If
there are tasks with the same PID values using the same shmem object,
the wrong destroy decision could be reached.
On shm segment creation store the pointer to the creator task in
shmid_kernel->shm_creator field and zero it on task exit. Then
use the ->shm_creator insread of shm_cprid in both functions. As
shmid_kernel object is already locked at this stage, no additional
locking is needed.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (71 commits)
[SCSI] fcoe: cleanup cpu selection for incoming requests
[SCSI] fcoe: add fip retry to avoid missing critical keep alive
[SCSI] libfc: fix warn on in lport retry
[SCSI] libfc: Remove the reference to FCP packet from scsi_cmnd in case of error
[SCSI] libfc: cleanup sending SRR request
[SCSI] libfc: two minor changes in comments
[SCSI] libfc, fcoe: ignore rx frame with wrong xid info
[SCSI] libfc: release exchg cache
[SCSI] libfc: use FC_MAX_ERROR_CNT
[SCSI] fcoe: remove unused ptype field in fcoe_rcv_info
[SCSI] bnx2fc: Update copyright and bump version to 1.0.4
[SCSI] bnx2fc: Tx BDs cache in write tasks
[SCSI] bnx2fc: Do not arm CQ when there are no CQEs
[SCSI] bnx2fc: hold tgt lock when calling cmd_release
[SCSI] bnx2fc: Enable support for sequence level error recovery
[SCSI] bnx2fc: HSI changes for tape
[SCSI] bnx2fc: Handle REC_TOV error code from firmware
[SCSI] bnx2fc: REC/SRR link service request and response handling
[SCSI] bnx2fc: Support 'sequence cleanup' task
[SCSI] dh_rdac: Associate HBA and storage in rdac_controller to support partitions in storage
...
If the directory contents change, then we have to accept that the
file->f_pos value may shrink if we do a 'search-by-cookie'. In that
case, we should turn off the loop detection and let the NFS client
try to recover.
The patch also fixes a second loop detection bug by ensuring
that after turning on the ctx->duped flag, we read at least one new
cookie into ctx->dir_cookie before attempting to match with
ctx->dup_cookie.
Reported-by: Petr Vandrovec <petr@vandrovec.name>
Cc: stable@kernel.org [2.6.39+]
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'slub/lockless' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6: (21 commits)
slub: When allocating a new slab also prep the first object
slub: disable interrupts in cmpxchg_double_slab when falling back to pagelock
Avoid duplicate _count variables in page_struct
Revert "SLUB: Fix build breakage in linux/mm_types.h"
SLUB: Fix build breakage in linux/mm_types.h
slub: slabinfo update for cmpxchg handling
slub: Not necessary to check for empty slab on load_freelist
slub: fast release on full slab
slub: Add statistics for the case that the current slab does not match the node
slub: Get rid of the another_slab label
slub: Avoid disabling interrupts in free slowpath
slub: Disable interrupts in free_debug processing
slub: Invert locking and avoid slab lock
slub: Rework allocator fastpaths
slub: Pass kmem_cache struct to lock and freeze slab
slub: explicit list_lock taking
slub: Add cmpxchg_double_slab()
mm: Rearrange struct page
slub: Move page->frozen handling near where the page->freelist handling occurs
slub: Do not use frozen page flag but a bit in the page counters
...
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
kconfig: Introduce IS_ENABLED(), IS_BUILTIN() and IS_MODULE()
xconfig: Abort close if configuration cannot be saved
kconfig: fix missing "0x" prefix from S_HEX symbol in autoconf.h
kconfig/nconf: remove useless conditionnal
kconfig/nconf: prevent segfault on empty menu
kconfig/nconf: use the generic menu_get_ext_help()
nconfig: Avoid Wunused-but-set warning
kconfig/conf: mark xfgets() private
kconfig: remove pending prototypes for kconfig_load()
kconfig/conf: add command line options' description
kconfig/conf: reduce the scope of `defconfig_file'
kconfig: use calloc() for expr allocation
kconfig: introduce specialized printer
kconfig: do not overwrite symbol direct dependency in assignment
kconfig/gconf: silent missing prototype warnings
kconfig/gconf: kill deadcode
kconfig: nuke LKC_DIRECT_LINK cruft
kconfig: nuke reference to SWIG
kconfig: add missing <stdlib.h> inclusion
kconfig: add missing <ctype.h> inclusion
...
Fix up conflicts in scripts/kconfig/Makefile
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
* 'next/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (21 commits)
arm/dt: tegra devicetree support
arm/versatile: Add device tree support
dt/irq: add irq_domain_generate_simple() helper
irq: add irq_domain translation infrastructure
dmaengine: imx-sdma: add device tree probe support
dmaengine: imx-sdma: sdma_get_firmware does not need to copy fw_name
dmaengine: imx-sdma: use platform_device_id to identify sdma version
mmc: sdhci-esdhc-imx: add device tree probe support
mmc: sdhci-pltfm: dt device does not pass parent to sdhci_alloc_host
mmc: sdhci-esdhc-imx: get rid of the uses of cpu_is_mx()
mmc: sdhci-esdhc-imx: do not reference platform data after probe
mmc: sdhci-esdhc-imx: extend card_detect and write_protect support for mx5
net/fec: add device tree probe support
net: ibm_newemac: convert it to use of_get_phy_mode
dt/net: add helper function of_get_phy_mode
net/fec: gasket needs to be enabled for some i.mx
serial/imx: add device tree probe support
serial/imx: get rid of the uses of cpu_is_mx1()
arm/dt: Add dtb make rule
arm/dt: Add skeleton dtsi file
...
Replace the config_is_*() macros with a variant that allows for grepping
for usage of CONFIG_* options in the code. Usage:
if (IS_ENABLED(CONFIG_NUMA))
or
#if IS_ENABLED(CONFIG_NUMA)
The IS_ENABLED() macro evaluates to 1 if the argument is set (to either 'y'
or 'm'), IS_BUILTIN() tests if the option is 'y' and IS_MODULE() test if
the option is 'm'. Only boolean and tristate options are supported.
Reviewed-by: Arnaud Lacombe <lacombar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Michal Marek <mmarek@suse.cz>
This is needed to match wireless cards with Intersil firmware that have
ID 0x0156:0x0002 and the third ID "Version 01.02". Such cards are
currently matched by orinoco_cs, which doesn't support WPA. They should
be matched by hostap_cs.
The first and the second product ID vary widely, so there are few users
with some particular IDs. Of those, very few can submit a patch for
hostap_cs or write a useful bugreport. It's still important to support
their hardware properly.
With PCMCIA_DEVICE_MANF_CARD_PROD_ID3, it should be possible to cover
the remaining Intersil based designs that kept the numeric ID and the
"version" of the reference design.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
tg3: Remove 5719 jumbo frames and TSO blocks
tg3: Break larger frags into 4k chunks for 5719
tg3: Add tx BD budgeting code
tg3: Consolidate code that calls tg3_tx_set_bd()
tg3: Add partial fragment unmapping code
tg3: Generalize tg3_skb_error_unmap()
tg3: Remove short DMA check for 1st fragment
tg3: Simplify tx bd assignments
tg3: Reintroduce tg3_tx_ring_info
ASIX: Use only 11 bits of header for data size
ASIX: Simplify condition in rx_fixup()
Fix cdc-phonet build
bonding: reduce noise during init
bonding: fix string comparison errors
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
net: add IFF_SKB_TX_SHARED flag to priv_flags
net: sock_sendmsg_nosec() is static
forcedeth: fix vlans
gianfar: fix bug caused by 87c288c6e9
gro: Only reset frag0 when skb can be pulled
...
* 'for-linus' of git://neil.brown.name/md: (75 commits)
md/raid10: handle further errors during fix_read_error better.
md/raid10: Handle read errors during recovery better.
md/raid10: simplify read error handling during recovery.
md/raid10: record bad blocks due to write errors during resync/recovery.
md/raid10: attempt to fix read errors during resync/check
md/raid10: Handle write errors by updating badblock log.
md/raid10: clear bad-block record when write succeeds.
md/raid10: avoid writing to known bad blocks on known bad drives.
md/raid10 record bad blocks as needed during recovery.
md/raid10: avoid reading known bad blocks during resync/recovery.
md/raid10 - avoid reading from known bad blocks - part 3
md/raid10: avoid reading from known bad blocks - part 2
md/raid10: avoid reading from known bad blocks - part 1
md/raid10: Split handle_read_error out from raid10d.
md/raid10: simplify/reindent some loops.
md/raid5: Clear bad blocks on successful write.
md/raid5. Don't write to known bad block on doubtful devices.
md/raid5: write errors should be recorded as bad blocks if possible.
md/raid5: use bad-block log to improve handling of uncorrectable read errors.
md/raid5: avoid reading from known bad blocks.
...
There is no need to cache the ptype in fcoe_rcv_info struct as it is never
used anywhere.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add min_timeout (minimum timeout) and max_timeout
values so that the framework can check if the new
timeout value is between the minimum and maximum
timeout values. If both values are 0, then the
framework will leave the check for the watchdog
device driver itself.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add support for extra ioctl calls by adding a
ioctl watchdog operation. This operation will be
called before we do our own handling of ioctl
commands. This way we can override the internal
ioctl command handling and we can also add
extra ioctl commands. The ioctl watchdog operation
should return the appropriate error codes or
-ENOIOCTLCMD if the ioctl command should be handled
through the internal ioctl handling of the framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add support for the nowayout feature to the
WatchDog Timer Driver Core framework.
This feature prevents the watchdog timer from being
stopped.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add support for the Magic Close feature to the
WatchDog Timer Driver Core framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This part add's the WDIOC_SETTIMEOUT and WDIOC_GETTIMEOUT ioctl
functionality to the WatchDog Timer Driver Core framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This part add's the WDIOC_SETOPTIONS ioctl functionality
to the WatchDog Timer Driver Core framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This part add's the basic ioctl functionality to the
WatchDog Timer Driver Core framework. The supported
ioctl call's are:
WDIOC_GETSUPPORT
WDIOC_GETSTATUS
WDIOC_GETBOOTSTATUS
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
The WatchDog Timer Driver Core is a framework
that contains the common code for all watchdog-driver's.
It also introduces a watchdog device structure and the
operations that go with it.
This is the introduction of this framework. This part
supports the minimal watchdog userspace API (or with
other words: the functionality to use /dev/watchdog's
open, release and write functionality as defined in
the simplest watchdog API). Extra functionality will
follow in the next set of patches.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
irq_domain_generate_simple() is an easy way to generate an irq translation
domain for simple irq controllers. It assumes a flat 1:1 mapping from
hardware irq number to an offset of the first linux irq number assigned
to the controller
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds irq_domain infrastructure for translating from
hardware irq numbers to linux irqs. This is particularly important
for architectures adding device tree support because the current
implementation (excluding PowerPC and SPARC) cannot handle
translation for more than a single interrupt controller. irq_domain
supports device tree translation for any number of interrupt
controllers.
This patch converts x86, Microblaze, ARM and MIPS to use irq_domain
for device tree irq translation. x86 is untested beyond compiling it,
irq_domain is enabled for MIPS and Microblaze, but the old behaviour is
preserved until the core code is modified to actually register an
irq_domain yet. On ARM it works and is required for much of the new
ARM device tree board support.
PowerPC has /not/ been converted to use this new infrastructure. It
is still missing some features before it can replace the virq
infrastructure already in powerpc (see documentation on
irq_domain_map/unmap for details). Followup patches will add the
missing pieces and migrate PowerPC to use irq_domain.
SPARC has its own method of managing interrupts from the device tree
and is unaffected by this change.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add support for NTC Thermistor series. In this release, the
following thermistors are supported: NCP15WB473, NCP18WB473, NCP03WB473,
and NCP15WL333. This driver is based on the datasheet of MURATA.
The driver in the patch does conversion from the raw ADC value
(either voltage or resistence) to temperature. In order to use
voltage values as input, the circuit schematics should be provided
with the platform data. A compensation table for each type of thermistor
is provided for the conversion.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Pktgen attempts to transmit shared skbs to net devices, which can't be used by
some drivers as they keep state information in skbs. This patch adds a flag
marking drivers as being able to handle shared skbs in their tx path. Drivers
are defaulted to being unable to do so, but calling ether_setup enables this
flag, as 90% of the drivers calling ether_setup touch real hardware and can
handle shared skbs. A subsequent patch will audit drivers to ensure that the
flag is set properly
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Jiri Pirko <jpirko@redhat.com>
CC: Robert Olsson <robert.olsson@its.uu.se>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Alexey Dobriyan <adobriyan@gmail.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (54 commits)
tpm_nsc: Fix bug when loading multiple TPM drivers
tpm: Move tpm_tis_reenable_interrupts out of CONFIG_PNP block
tpm: Fix compilation warning when CONFIG_PNP is not defined
TOMOYO: Update kernel-doc.
tpm: Fix a typo
tpm_tis: Probing function for Intel iTPM bug
tpm_tis: Fix the probing for interrupts
tpm_tis: Delay ACPI S3 suspend while the TPM is busy
tpm_tis: Re-enable interrupts upon (S3) resume
tpm: Fix display of data in pubek sysfs entry
tpm_tis: Add timeouts sysfs entry
tpm: Adjust interface timeouts if they are too small
tpm: Use interface timeouts returned from the TPM
tpm_tis: Introduce durations sysfs entry
tpm: Adjust the durations if they are too small
tpm: Use durations returned from TPM
TOMOYO: Enable conditional ACL.
TOMOYO: Allow using argv[]/envp[] of execve() as conditions.
TOMOYO: Allow using executable's realpath and symlink's target as conditions.
TOMOYO: Allow using owner/group etc. of file objects as conditions.
...
Fix up trivial conflict in security/tomoyo/realpath.c
