When detecting a spurious EL1 translation fault, we attempt to compare
ESR_EL1.DFSC with PAR_EL1.FST. We erroneously use FIELD_PREP() to
extract PAR_EL1.FST, when we should be using FIELD_GET().
In the wise words of Robin Murphy:
| FIELD_GET() is a UBFX, FIELD_PREP() is a BFI
Using FIELD_PREP() means that that dfsc & ESR_ELx_FSC_TYPE is always
zero, and hence not equal to ESR_ELx_FSC_FAULT. Thus we detect any
unhandled translation fault as spurious.
... so let's use FIELD_GET() to ensure we don't decide all translation
faults are spurious. ESR_EL1.DFSC occupies bits [5:0], and requires no
shifting.
Fixes: 42f91093b0 ("arm64: mm: Ignore spurious translation faults taken from the kernel")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Robin Murphy <robin.murphy@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
If we take an unhandled fault in the kernel, we call show_pte() to dump
the {PGDP,PGD,PUD,PMD,PTE} values for the corresponding page table walk,
where the PGDP value is virt_to_phys(mm->pgd).
The boot-time and runtime kernel page tables, init_pg_dir and
swapper_pg_dir respectively, are kernel symbols. Thus, it is not valid
to call virt_to_phys() on either of these, though we'll do so if we take
a fault on a TTBR1 address.
When CONFIG_DEBUG_VIRTUAL is not selected, virt_to_phys() will silently
fix this up. However, when CONFIG_DEBUG_VIRTUAL is selected, this
results in splats as below. Depending on when these occur, they can
happen to suppress information needed to debug the original unhandled
fault, such as the backtrace:
| Unable to handle kernel paging request at virtual address ffff7fffec73cf0f
| Mem abort info:
| ESR = 0x96000004
| EC = 0x25: DABT (current EL), IL = 32 bits
| SET = 0, FnV = 0
| EA = 0, S1PTW = 0
| Data abort info:
| ISV = 0, ISS = 0x00000004
| CM = 0, WnR = 0
| ------------[ cut here ]------------
| virt_to_phys used for non-linear address: 00000000102c9dbe (swapper_pg_dir+0x0/0x1000)
| WARNING: CPU: 1 PID: 7558 at arch/arm64/mm/physaddr.c:15 __virt_to_phys+0xe0/0x170 arch/arm64/mm/physaddr.c:12
| Kernel panic - not syncing: panic_on_warn set ...
| SMP: stopping secondary CPUs
| Dumping ftrace buffer:
| (ftrace buffer empty)
| Kernel Offset: disabled
| CPU features: 0x0002,23000438
| Memory Limit: none
| Rebooting in 1 seconds..
We can avoid this by ensuring that we call __pa_symbol() for
init_mm.pgd, as this will always be a kernel symbol. As the dumped
{PGD,PUD,PMD,PTE} values are the raw values from the relevant entries we
don't need to handle these specially.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
* for-next/52-bit-kva: (25 commits)
Support for 52-bit virtual addressing in kernel space
* for-next/cpu-topology: (9 commits)
Move CPU topology parsing into core code and add support for ACPI 6.3
* for-next/error-injection: (2 commits)
Support for function error injection via kprobes
* for-next/perf: (8 commits)
Support for i.MX8 DDR PMU and proper SMMUv3 group validation
* for-next/psci-cpuidle: (7 commits)
Move PSCI idle code into a new CPUidle driver
* for-next/rng: (4 commits)
Support for 'rng-seed' property being passed in the devicetree
* for-next/smpboot: (3 commits)
Reduce fragility of secondary CPU bringup in debug configurations
* for-next/tbi: (10 commits)
Introduce new syscall ABI with relaxed requirements for pointer tags
* for-next/tlbi: (6 commits)
Handle spurious page faults arising from kernel space
Thanks to address translation being performed out of order with respect to
loads and stores, it is possible for a CPU to take a translation fault when
accessing a page that was mapped by a different CPU.
For example, in the case that one CPU maps a page and then sets a flag to
tell another CPU:
CPU 0
-----
MOV X0, <valid pte>
STR X0, [Xptep] // Store new PTE to page table
DSB ISHST
ISB
MOV X1, #1
STR X1, [Xflag] // Set the flag
CPU 1
-----
loop: LDAR X0, [Xflag] // Poll flag with Acquire semantics
CBZ X0, loop
LDR X1, [X2] // Translates using the new PTE
then the final load on CPU 1 can raise a translation fault because the
translation can be performed speculatively before the read of the flag and
marked as "faulting" by the CPU. This isn't quite as bad as it sounds
since, in reality, code such as:
CPU 0 CPU 1
----- -----
spin_lock(&lock); spin_lock(&lock);
*ptr = vmalloc(size); if (*ptr)
spin_unlock(&lock); foo = **ptr;
spin_unlock(&lock);
will not trigger the fault because there is an address dependency on CPU 1
which prevents the speculative translation. However, more exotic code where
the virtual address is known ahead of time, such as:
CPU 0 CPU 1
----- -----
spin_lock(&lock); spin_lock(&lock);
set_fixmap(0, paddr, prot); if (mapped)
mapped = true; foo = *fix_to_virt(0);
spin_unlock(&lock); spin_unlock(&lock);
could fault. This can be avoided by any of:
* Introducing broadcast TLB maintenance on the map path
* Adding a DSB;ISB sequence after checking a flag which indicates
that a virtual address is now mapped
* Handling the spurious fault
Given that we have never observed a problem due to this under Linux and
future revisions of the architecture are being tightened so that
translation table walks are effectively ordered in the same way as explicit
memory accesses, we no longer treat spurious kernel faults as fatal if an
AT instruction indicates that the access does not trigger a translation
fault.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
VA_START used to be the start of the TTBR1 address space, but now it's a
point midway though. In a couple of places we still use VA_START to get
the start of the TTBR1 address space, so let's fix these up to use
PAGE_OFFSET instead.
Fixes: 14c127c957 ("arm64: mm: Flip kernel VA space")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Previous patches have enabled 52-bit kernel + user VAs and there is no
longer any scenario where user VA != kernel VA size.
This patch removes the, now redundant, vabits_user variable and replaces
usage with vabits_actual where appropriate.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
In order to support 52-bit kernel addresses detectable at boot time, one
needs to know the actual VA_BITS detected. A new variable vabits_actual
is introduced in this commit and employed for the KVM hypervisor layout,
KASAN, fault handling and phys-to/from-virt translation where there
would normally be compile time constants.
In order to maintain performance in phys_to_virt, another variable
physvirt_offset is introduced.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
This change prints the hexadecimal EC value in mem_abort_decode(),
which makes it easier to lookup the corresponding EC in
the ARM Architecture Reference Manual.
The commit 1f9b8936f3 ("arm64: Decode information from ESR upon mem
faults") prints useful information when memory abort occurs. It would
be easier to lookup "0x25" instead of "DABT" in the document. Then we
can check the corresponding ISS.
For example:
Current info Document
EC Exception class
"CP15 MCR/MRC" 0x3 "MCR or MRC access to CP15a..."
"ASIMD" 0x7 "Access to SIMD or floating-point..."
"DABT (current EL)" 0x25 "Data Abort taken without..."
...
Before:
Unable to handle kernel paging request at virtual address 000000000000c000
Mem abort info:
ESR = 0x96000046
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000046
CM = 0, WnR = 1
After:
Unable to handle kernel paging request at virtual address 000000000000c000
Mem abort info:
ESR = 0x96000046
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000046
CM = 0, WnR = 1
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: James Morse <james.morse@arm.com>
Acked-by: Mark Rutland <Mark.rutland@arm.com>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Will Deacon <will@kernel.org>
Make debug exceptions visible from RCU so that synchronize_rcu()
correctly track the debug exception handler.
This also introduces sanity checks for user-mode exceptions as same
as x86's ist_enter()/ist_exit().
The debug exception can interrupt in idle task. For example, it warns
if we put a kprobe on a function called from idle task as below.
The warning message showed that the rcu_read_lock() caused this
problem. But actually, this means the RCU is lost the context which
is already in NMI/IRQ.
/sys/kernel/debug/tracing # echo p default_idle_call >> kprobe_events
/sys/kernel/debug/tracing # echo 1 > events/kprobes/enable
/sys/kernel/debug/tracing # [ 135.122237]
[ 135.125035] =============================
[ 135.125310] WARNING: suspicious RCU usage
[ 135.125581] 5.2.0-08445-g9187c508bdc7 #20 Not tainted
[ 135.125904] -----------------------------
[ 135.126205] include/linux/rcupdate.h:594 rcu_read_lock() used illegally while idle!
[ 135.126839]
[ 135.126839] other info that might help us debug this:
[ 135.126839]
[ 135.127410]
[ 135.127410] RCU used illegally from idle CPU!
[ 135.127410] rcu_scheduler_active = 2, debug_locks = 1
[ 135.128114] RCU used illegally from extended quiescent state!
[ 135.128555] 1 lock held by swapper/0/0:
[ 135.128944] #0: (____ptrval____) (rcu_read_lock){....}, at: call_break_hook+0x0/0x178
[ 135.130499]
[ 135.130499] stack backtrace:
[ 135.131192] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.2.0-08445-g9187c508bdc7 #20
[ 135.131841] Hardware name: linux,dummy-virt (DT)
[ 135.132224] Call trace:
[ 135.132491] dump_backtrace+0x0/0x140
[ 135.132806] show_stack+0x24/0x30
[ 135.133133] dump_stack+0xc4/0x10c
[ 135.133726] lockdep_rcu_suspicious+0xf8/0x108
[ 135.134171] call_break_hook+0x170/0x178
[ 135.134486] brk_handler+0x28/0x68
[ 135.134792] do_debug_exception+0x90/0x150
[ 135.135051] el1_dbg+0x18/0x8c
[ 135.135260] default_idle_call+0x0/0x44
[ 135.135516] cpu_startup_entry+0x2c/0x30
[ 135.135815] rest_init+0x1b0/0x280
[ 135.136044] arch_call_rest_init+0x14/0x1c
[ 135.136305] start_kernel+0x4d4/0x500
[ 135.136597]
So make debug exception visible to RCU can fix this warning.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: Paul E. McKenney <paulmck@linux.ibm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Architectures which support kprobes have very similar boilerplate around
calling kprobe_fault_handler(). Use a helper function in kprobes.h to
unify them, based on the x86 code.
This changes the behaviour for other architectures when preemption is
enabled. Previously, they would have disabled preemption while calling
the kprobe handler. However, preemption would be disabled if this fault
was due to a kprobe, so we know the fault was not due to a kprobe
handler and can simply return failure.
This behaviour was introduced in commit a980c0ef9f ("x86/kprobes:
Refactor kprobes_fault() like kprobe_exceptions_notify()")
[anshuman.khandual@arm.com: export kprobe_fault_handler()]
Link: http://lkml.kernel.org/r/1561133358-8876-1-git-send-email-anshuman.khandual@arm.com
Link: http://lkml.kernel.org/r/1560420444-25737-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new XAFLAG
and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the 'arm_boot_flags'
introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
-----BEGIN PGP SIGNATURE-----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=0TDT
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new
XAFLAG and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the
'arm_boot_flags' introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
perf: arm_spe: Enable ACPI/Platform automatic module loading
arm_pmu: acpi: spe: Add initial MADT/SPE probing
ACPI/PPTT: Add function to return ACPI 6.3 Identical tokens
ACPI/PPTT: Modify node flag detection to find last IDENTICAL
x86/entry: Simplify _TIF_SYSCALL_EMU handling
arm64: rename dump_instr as dump_kernel_instr
arm64/mm: Drop [PTE|PMD]_TYPE_FAULT
arm64: Implement panic_smp_self_stop()
arm64: Improve parking of stopped CPUs
arm64: Expose FRINT capabilities to userspace
arm64: Expose ARMv8.5 CondM capability to userspace
arm64: defconfig: enable CONFIG_RANDOMIZE_BASE
arm64: ARM64_MODULES_PLTS must depend on MODULES
arm64: bpf: do not allocate executable memory
arm64/kprobes: set VM_FLUSH_RESET_PERMS on kprobe instruction pages
arm64/mm: wire up CONFIG_ARCH_HAS_SET_DIRECT_MAP
arm64: module: create module allocations without exec permissions
arm64: Allow user selection of ARM64_MODULE_PLTS
acpi/arm64: ignore 5.1 FADTs that are reported as 5.0
arm64: Allow selecting Pseudo-NMI again
...
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__do_page_fault() is over complicated with multiple goto statements. This
cleans up the code flow and while there drops local variable vm_fault_t.
Reviewed-by: Mark Rutland <Mark.rutland@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds an is_write_abort() wrapper and documents the detection
of the abort type on cache maintenance operations.
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
[catalin.marinas@arm.com: only keep the is_write_abort() wrapper]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The task_struct argument is not getting used in __do_page_fault(). Hence
just drop it and use current or cuurent->mm instead where ever required.
This does not change any functionality.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is an inconsistency between down_read_trylock() success and failure
paths while dealing with kernel access for non exception table areas where
it calls __do_kernel_fault(). In case of failure it just bails out without
holding mmap_sem but when it succeeds it does so while holding mmap_sem.
Fix this inconsistency by just dropping mmap_sem in success path as well.
__do_kernel_fault() calls die_kernel_fault() which then calls show_pte().
show_pte() in this path might become bit more unreliable without holding
mmap_sem. But there are already instances [1] in do_page_fault() where
die_kernel_fault() gets called without holding mmap_sem. show_pte() can
be made more robust independently but in a later patch.
[1] Conditional block for (is_ttbr0_addr && is_el1_permission_fault)
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We don't currently set the FAULT_FLAG_INSTRUCTION mm flag for EL0
instruction aborts. This has no functional impact, as we don't override
arch_vma_access_permitted(), and the default implementation always returns
true. However, it would be helpful to provide the flag so that it can be
consumed by tracepoints such as dax_pmd_fault.
This patch sets the FAULT_FLAG_INSTRUCTION flag for EL0 instruction aborts.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Fix incorrect LDADD instruction encoding in our disassembly macros
- Disable the broken ARM64_PSEUDO_NMI support for now
- Add workaround for Cortex-A76 CPU erratum #1463225
- Handle Cortex-A76/Neoverse-N1 erratum #1418040 w/ existing workaround
- Fix IORT build failure if IOMMU_SUPPORT=n
- Fix place-relative module relocation range checking and its
interaction with KASLR
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzoC8MACgkQt6xw3ITB
YzQfiAf+MXFzrAd3o7v40CnZu6ELw+ldedPh34oBjD7h6we3hroxi5Fss2nbwH0o
BmAm4Nv1/Njk5+hA7Mlp3/mRn0vcd3NDP+FyH3inLjUU7owc41thp0SKlCOfFdZk
K8sVCOeCWt7GEEPcnFsPO0nU+7f3ZKDDNBo0L+qJPxrMOTDcbQ3cIjW/ua7vQRHv
pIDGF+iJAhHeNoc1Wjq08F8Q+Dq7dYvhtokeyDivSn4NulmRvdL+z581gMmj7ExT
ARB6WtHGoOo+8UdjBJIDnXRKhJLfGexQaoAojk+IogaV0ACDtz6CuqsSIh1e5SFC
oPqRSP5ITTbXEDS5uaUW1pYlwmGTaw==
=ynUz
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 fixes from Will Deacon:
- Fix incorrect LDADD instruction encoding in our disassembly macros
- Disable the broken ARM64_PSEUDO_NMI support for now
- Add workaround for Cortex-A76 CPU erratum #1463225
- Handle Cortex-A76/Neoverse-N1 erratum #1418040 w/ existing workaround
- Fix IORT build failure if IOMMU_SUPPORT=n
- Fix place-relative module relocation range checking and its
interaction with KASLR
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: insn: Add BUILD_BUG_ON() for invalid masks
arm64: insn: Fix ldadd instruction encoding
arm64: Kconfig: Make ARM64_PSEUDO_NMI depend on BROKEN for now
arm64: Handle erratum 1418040 as a superset of erratum 1188873
arm64/module: deal with ambiguity in PRELxx relocation ranges
ACPI/IORT: Fix build error when IOMMU_SUPPORT is disabled
arm64/kernel: kaslr: reduce module randomization range to 2 GB
arm64: errata: Add workaround for Cortex-A76 erratum #1463225
arm64: Remove useless message during oops
Revisions of the Cortex-A76 CPU prior to r4p0 are affected by an erratum
that can prevent interrupts from being taken when single-stepping.
This patch implements a software workaround to prevent userspace from
effectively being able to disable interrupts.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When dumping the page table in response to an unexpected kernel page
fault, we print the virtual (hashed) address of the page table base, but
display physical addresses for everything else.
Make the page table dumping code in show_pte() consistent, by printing
the page table base pointer as a physical address.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
do_debug_exception() goes out of its way to return a value that isn't
ever used, so just make the thing void.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Pseudo NMI support for arm64 using GICv3 interrupt priorities
- uaccess macros clean-up (unsafe user accessors also merged but
reverted, waiting for objtool support on arm64)
- ptrace regsets for Pointer Authentication (ARMv8.3) key management
- inX() ordering w.r.t. delay() on arm64 and riscv (acks in place by the
riscv maintainers)
- arm64/perf updates: PMU bindings converted to json-schema, unused
variable and misleading comment removed
- arm64/debug fixes to ensure checking of the triggering exception level
and to avoid the propagation of the UNKNOWN FAR value into the si_code
for debug signals
- Workaround for Fujitsu A64FX erratum 010001
- lib/raid6 ARM NEON optimisations
- NR_CPUS now defaults to 256 on arm64
- Minor clean-ups (documentation/comments, Kconfig warning, unused
asm-offsets, clang warnings)
- MAINTAINERS update for list information to the ARM64 ACPI entry
-----BEGIN PGP SIGNATURE-----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=2U56
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- Pseudo NMI support for arm64 using GICv3 interrupt priorities
- uaccess macros clean-up (unsafe user accessors also merged but
reverted, waiting for objtool support on arm64)
- ptrace regsets for Pointer Authentication (ARMv8.3) key management
- inX() ordering w.r.t. delay() on arm64 and riscv (acks in place by
the riscv maintainers)
- arm64/perf updates: PMU bindings converted to json-schema, unused
variable and misleading comment removed
- arm64/debug fixes to ensure checking of the triggering exception
level and to avoid the propagation of the UNKNOWN FAR value into the
si_code for debug signals
- Workaround for Fujitsu A64FX erratum 010001
- lib/raid6 ARM NEON optimisations
- NR_CPUS now defaults to 256 on arm64
- Minor clean-ups (documentation/comments, Kconfig warning, unused
asm-offsets, clang warnings)
- MAINTAINERS update for list information to the ARM64 ACPI entry
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
arm64: mmu: drop paging_init comments
arm64: debug: Ensure debug handlers check triggering exception level
arm64: debug: Don't propagate UNKNOWN FAR into si_code for debug signals
Revert "arm64: uaccess: Implement unsafe accessors"
arm64: avoid clang warning about self-assignment
arm64: Kconfig.platforms: fix warning unmet direct dependencies
lib/raid6: arm: optimize away a mask operation in NEON recovery routine
lib/raid6: use vdupq_n_u8 to avoid endianness warnings
arm64: io: Hook up __io_par() for inX() ordering
riscv: io: Update __io_[p]ar() macros to take an argument
asm-generic/io: Pass result of I/O accessor to __io_[p]ar()
arm64: Add workaround for Fujitsu A64FX erratum 010001
arm64: Rename get_thread_info()
arm64: Remove documentation about TIF_USEDFPU
arm64: irqflags: Fix clang build warnings
arm64: Enable the support of pseudo-NMIs
arm64: Skip irqflags tracing for NMI in IRQs disabled context
arm64: Skip preemption when exiting an NMI
arm64: Handle serror in NMI context
irqchip/gic-v3: Allow interrupts to be set as pseudo-NMI
...
FAR_EL1 is UNKNOWN for all debug exceptions other than those caused by
taking a hardware watchpoint. Unfortunately, if a debug handler returns
a non-zero value, then we will propagate the UNKNOWN FAR value to
userspace via the si_addr field of the SIGTRAP siginfo_t.
Instead, let's set si_addr to take on the PC of the faulting instruction,
which we have available in the current pt_regs.
Cc: <stable@vger.kernel.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
To split up APEIs in_nmi() path, the caller needs to always be
in_nmi(). Add a helper to do the work and claim the notification.
When KVM or the arch code takes an exception that might be a RAS
notification, it asks the APEI firmware-first code whether it wants
to claim the exception. A future kernel-first mechanism may be queried
afterwards, and claim the notification, otherwise we fall through
to the existing default behaviour.
The NOTIFY_SEA code was merged before considering multiple, possibly
interacting, NMI-like notifications and the need to consider kernel
first in the future. Make the 'claiming' behaviour explicit.
Restructuring the APEI code to allow multiple NMI-like notifications
means any notification that might interrupt interrupts-masked
code must always be wrapped in nmi_enter()/nmi_exit(). This will
allow APEI to use in_nmi() to use the right fixmap entries.
Mask SError over this window to prevent an asynchronous RAS error
arriving and tripping 'nmi_enter()'s BUG_ON(in_nmi()).
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To split up APEIs in_nmi() path, the caller needs to always be
in_nmi(). KVM shouldn't have to know about this, pull the RAS plumbing
out into a header file.
Currently guest synchronous external aborts are claimed as RAS
notifications by handle_guest_sea(), which is hidden in the arch codes
mm/fault.c. 32bit gets a dummy declaration in system_misc.h.
There is going to be more of this in the future if/when the kernel
supports the SError-based firmware-first notification mechanism and/or
kernel-first notifications for both synchronous external abort and
SError. Each of these will come with some Kconfig symbols and a
handful of header files.
Create a header file for all this.
This patch gives handle_guest_sea() a 'kvm_' prefix, and moves the
declarations to kvm_ras.h as preparation for a future patch that moves
the ACPI-specific RAS code out of mm/fault.c.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Right now arm64 fault handling code removes pointer tags from addresses
covered by TTBR0 in faults taken from both EL0 and EL1, but doesn't do
that for pointers covered by TTBR1.
This patch adds two helper functions is_ttbr0_addr() and is_ttbr1_addr(),
where the latter one accounts for the fact that TTBR1 pointers might be
tagged when tag-based KASAN is in use, and uses these helper functions to
perform pointer checks in arch/arm64/mm/fault.c.
Link: http://lkml.kernel.org/r/3f349b0e9e48b5df3298a6b4ae0634332274494a.1544099024.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On arm64 there is optional support for a 52-bit virtual address space.
To exploit this one has to be running with a 64KB page size and be
running on hardware that supports this.
For an arm64 kernel supporting a 48 bit VA with a 64KB page size,
some changes are needed to support a 52-bit userspace:
* TCR_EL1.T0SZ needs to be 12 instead of 16,
* TASK_SIZE needs to reflect the new size.
This patch implements the above when the support for 52-bit VAs is
detected at early boot time.
On arm64 userspace addresses translation is controlled by TTBR0_EL1. As
well as userspace, TTBR0_EL1 controls:
* The identity mapping,
* EFI runtime code.
It is possible to run a kernel with an identity mapping that has a
larger VA size than userspace (and for this case __cpu_set_tcr_t0sz()
would set TCR_EL1.T0SZ as appropriate). However, when the conditions for
52-bit userspace are met; it is possible to keep TCR_EL1.T0SZ fixed at
12. Thus in this patch, the TCR_EL1.T0SZ size changing logic is
disabled.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
For EL0 entries requiring bp_hardening, daif status is kept at
DAIF_PROCCTX_NOIRQ until after hardening has been done. Then interrupts
are enabled through local_irq_enable().
Before using local_irq_* functions, daifflags should be properly restored
to a state where IRQs are enabled.
Enable IRQs by restoring DAIF_PROCCTX state after bp hardening.
Acked-by: James Morse <james.morse@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
fault_info[] and debug_fault_info[] are static arrays defining memory abort
exception handling functions looking into ESR fault status code encodings.
As esr_to_fault_info() is already available providing fault_info[] array
lookup, it really makes sense to have a corresponding debug_fault_info[]
array lookup function as well. This just adds an equivalent helper function
esr_to_debug_fault_info().
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Most memory abort exception handling related functions have the arguments
in the order (addr, esr, regs) except is_el1_permission_fault(). This
changes the argument order in this function as (addr, esr, regs) like
others.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Just replace hard code value of 63 (0x111111) with an existing macro
ESR_ELx_FSC when parsing for the status code during fault exception.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add arm64_force_sig_mceerr for consistency with arm64_force_sig_fault,
and use it in the one location that can take advantage of it.
This removes the fiddly filling out of siginfo before sending a signal
reporting an memory error to userspace.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Wrap force_sig_fault with a helper that calls arm64_show_signal
and call arm64_force_sig_fault where appropraite.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
This code is truly common between the signal sending cases so share it.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
As this work is truly common between all of the signal sending cases
there is no need to repeat it between the different cases.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Not all of the signals passed to __do_user_fault can be handled
the same way so expand the now tiny __do_user_fault in it's callers
and remove it.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
It gets easy to confuse what is going on when some code is shared and some not
so stop sharing the trivial bits of signal generation to make future updates
easier to understand.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
These two cases are practically the same and use siginfo differently
from the other signals sent from do_page_fault. So consolidate them
to make future changes easier.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This pepares for sending signals with something other than
arm64_force_sig_info.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Every caller passes in current for tsk so there is no need to pass
tsk. Instead make tsk a local variable initialized to current.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Instead of generating a struct siginfo before calling arm64_notify_die
pass the signal number, tne sicode and the fault address into
arm64_notify_die and have it call force_sig_fault instead of
force_sig_info to let the generic code generate the struct siginfo.
This keeps code passing just the needed information into
siginfo generating code, making it easier to see what
is happening and harder to get wrong. Further by letting
the generic code handle the generation of struct siginfo
it reduces the number of sites generating struct siginfo
making it possible to review them and verify that all
of the fiddly details for a structure passed to userspace
are handled properly.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The cpu errata and feature enable callbacks are only called via their
respective arm64_cpu_capabilities structure and therefore shouldn't
exist in the global namespace.
Move the PAN, RAS and cache maintenance emulation enable callbacks into
the same files as their corresponding arm64_cpu_capabilities structures,
making them static in the process.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Use new return type vm_fault_t for fault handler. For now, this is just
documenting that the function returns a VM_FAULT value rather than an
errno. Once all instances are converted, vm_fault_t will become a
distinct type.
Ref-> commit 1c8f422059 ("mm: change return type to vm_fault_t")
In this patch all the caller of handle_mm_fault() are changed to return
vm_fault_t type.
Link: http://lkml.kernel.org/r/20180617084810.GA6730@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: David S. Miller <davem@davemloft.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Levin, Alexander (Sasha Levin)" <alexander.levin@verizon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A bunch of good stuff in here:
- Wire up support for qspinlock, replacing our trusty ticket lock code
- Add an IPI to flush_icache_range() to ensure that stale instructions
fetched into the pipeline are discarded along with the I-cache lines
- Support for the GCC "stackleak" plugin
- Support for restartable sequences, plus an arm64 port for the selftest
- Kexec/kdump support on systems booting with ACPI
- Rewrite of our syscall entry code in C, which allows us to zero the
GPRs on entry from userspace
- Support for chained PMU counters, allowing 64-bit event counters to be
constructed on current CPUs
- Ensure scheduler topology information is kept up-to-date with CPU
hotplug events
- Re-enable support for huge vmalloc/IO mappings now that the core code
has the correct hooks to use break-before-make sequences
- Miscellaneous, non-critical fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJbbV41AAoJELescNyEwWM0WoEIALhrKtsIn6vqFlSs/w6aDuJL
cMWmFxjTaKLmIq2+cJIdFLOJ3CH80Pu9gB+nEv/k+cZdCTfUVKfRf28HTpmYWsht
bb4AhdHMC7yFW752BHk+mzJspeC8h/2Rm8wMuNVplZ3MkPrwo3vsiuJTofLhVL/y
BihlU3+5sfBvCYIsWnuEZIev+/I/s/qm1ASiqIcKSrFRZP6VTt5f9TC75vFI8seW
7yc3odKb0CArexB8yBjiPNziehctQF42doxQyL45hezLfWw4qdgHOSiwyiOMxEz9
Fwwpp8Tx33SKLNJgqoqYznGW9PhYJ7n2Kslv19uchJrEV+mds82vdDNaWRULld4=
=kQn6
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"A bunch of good stuff in here. Worth noting is that we've pulled in
the x86/mm branch from -tip so that we can make use of the core
ioremap changes which allow us to put down huge mappings in the
vmalloc area without screwing up the TLB. Much of the positive
diffstat is because of the rseq selftest for arm64.
Summary:
- Wire up support for qspinlock, replacing our trusty ticket lock
code
- Add an IPI to flush_icache_range() to ensure that stale
instructions fetched into the pipeline are discarded along with the
I-cache lines
- Support for the GCC "stackleak" plugin
- Support for restartable sequences, plus an arm64 port for the
selftest
- Kexec/kdump support on systems booting with ACPI
- Rewrite of our syscall entry code in C, which allows us to zero the
GPRs on entry from userspace
- Support for chained PMU counters, allowing 64-bit event counters to
be constructed on current CPUs
- Ensure scheduler topology information is kept up-to-date with CPU
hotplug events
- Re-enable support for huge vmalloc/IO mappings now that the core
code has the correct hooks to use break-before-make sequences
- Miscellaneous, non-critical fixes and cleanups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (90 commits)
arm64: alternative: Use true and false for boolean values
arm64: kexec: Add comment to explain use of __flush_icache_range()
arm64: sdei: Mark sdei stack helper functions as static
arm64, kaslr: export offset in VMCOREINFO ELF notes
arm64: perf: Add cap_user_time aarch64
efi/libstub: Only disable stackleak plugin for arm64
arm64: drop unused kernel_neon_begin_partial() macro
arm64: kexec: machine_kexec should call __flush_icache_range
arm64: svc: Ensure hardirq tracing is updated before return
arm64: mm: Export __sync_icache_dcache() for xen-privcmd
drivers/perf: arm-ccn: Use devm_ioremap_resource() to map memory
arm64: Add support for STACKLEAK gcc plugin
arm64: Add stack information to on_accessible_stack
drivers/perf: hisi: update the sccl_id/ccl_id when MT is supported
arm64: fix ACPI dependencies
rseq/selftests: Add support for arm64
arm64: acpi: fix alignment fault in accessing ACPI
efi/arm: map UEFI memory map even w/o runtime services enabled
efi/arm: preserve early mapping of UEFI memory map longer for BGRT
drivers: acpi: add dependency of EFI for arm64
...
In order to remove the additional check before calling the
ghes_notify_sea(), make stub definition when !CONFIG_ACPI_APEI_SEA.
After this cleanup, we can simply call the ghes_notify_sea() to let
APEI driver handle the SEA notification.
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we have sysreg_clear_set(), we can consistently use this
instead of config_sctlr_el1().
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Spectre v4 mitigation (Speculative Store Bypass Disable) support for
arm64 using SMC firmware call to set a hardware chicken bit
- ACPI PPTT (Processor Properties Topology Table) parsing support and
enable the feature for arm64
- Report signal frame size to user via auxv (AT_MINSIGSTKSZ). The
primary motivation is Scalable Vector Extensions which requires more
space on the signal frame than the currently defined MINSIGSTKSZ
- ARM perf patches: allow building arm-cci as module, demote dev_warn()
to dev_dbg() in arm-ccn event_init(), miscellaneous cleanups
- cmpwait() WFE optimisation to avoid some spurious wakeups
- L1_CACHE_BYTES reverted back to 64 (for performance reasons that have
to do with some network allocations) while keeping ARCH_DMA_MINALIGN
to 128. cache_line_size() returns the actual hardware Cache Writeback
Granule
- Turn LSE atomics on by default in Kconfig
- Kernel fault reporting tidying
- Some #include and miscellaneous cleanups
-----BEGIN PGP SIGNATURE-----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=uums
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Apart from the core arm64 and perf changes, the Spectre v4 mitigation
touches the arm KVM code and the ACPI PPTT support touches drivers/
(acpi and cacheinfo). I should have the maintainers' acks in place.
Summary:
- Spectre v4 mitigation (Speculative Store Bypass Disable) support
for arm64 using SMC firmware call to set a hardware chicken bit
- ACPI PPTT (Processor Properties Topology Table) parsing support and
enable the feature for arm64
- Report signal frame size to user via auxv (AT_MINSIGSTKSZ). The
primary motivation is Scalable Vector Extensions which requires
more space on the signal frame than the currently defined
MINSIGSTKSZ
- ARM perf patches: allow building arm-cci as module, demote
dev_warn() to dev_dbg() in arm-ccn event_init(), miscellaneous
cleanups
- cmpwait() WFE optimisation to avoid some spurious wakeups
- L1_CACHE_BYTES reverted back to 64 (for performance reasons that
have to do with some network allocations) while keeping
ARCH_DMA_MINALIGN to 128. cache_line_size() returns the actual
hardware Cache Writeback Granule
- Turn LSE atomics on by default in Kconfig
- Kernel fault reporting tidying
- Some #include and miscellaneous cleanups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (53 commits)
arm64: Fix syscall restarting around signal suppressed by tracer
arm64: topology: Avoid checking numa mask for scheduler MC selection
ACPI / PPTT: fix build when CONFIG_ACPI_PPTT is not enabled
arm64: cpu_errata: include required headers
arm64: KVM: Move VCPU_WORKAROUND_2_FLAG macros to the top of the file
arm64: signal: Report signal frame size to userspace via auxv
arm64/sve: Thin out initialisation sanity-checks for sve_max_vl
arm64: KVM: Add ARCH_WORKAROUND_2 discovery through ARCH_FEATURES_FUNC_ID
arm64: KVM: Handle guest's ARCH_WORKAROUND_2 requests
arm64: KVM: Add ARCH_WORKAROUND_2 support for guests
arm64: KVM: Add HYP per-cpu accessors
arm64: ssbd: Add prctl interface for per-thread mitigation
arm64: ssbd: Introduce thread flag to control userspace mitigation
arm64: ssbd: Restore mitigation status on CPU resume
arm64: ssbd: Skip apply_ssbd if not using dynamic mitigation
arm64: ssbd: Add global mitigation state accessor
arm64: Add 'ssbd' command-line option
arm64: Add ARCH_WORKAROUND_2 probing
arm64: Add per-cpu infrastructure to call ARCH_WORKAROUND_2
arm64: Call ARCH_WORKAROUND_2 on transitions between EL0 and EL1
...
Pull siginfo updates from Eric Biederman:
"This set of changes close the known issues with setting si_code to an
invalid value, and with not fully initializing struct siginfo. There
remains work to do on nds32, arc, unicore32, powerpc, arm, arm64, ia64
and x86 to get the code that generates siginfo into a simpler and more
maintainable state. Most of that work involves refactoring the signal
handling code and thus careful code review.
Also not included is the work to shrink the in kernel version of
struct siginfo. That depends on getting the number of places that
directly manipulate struct siginfo under control, as it requires the
introduction of struct kernel_siginfo for the in kernel things.
Overall this set of changes looks like it is making good progress, and
with a little luck I will be wrapping up the siginfo work next
development cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
signal/sh: Stop gcc warning about an impossible case in do_divide_error
signal/mips: Report FPE_FLTUNK for undiagnosed floating point exceptions
signal/um: More carefully relay signals in relay_signal.
signal: Extend siginfo_layout with SIL_FAULT_{MCEERR|BNDERR|PKUERR}
signal: Remove unncessary #ifdef SEGV_PKUERR in 32bit compat code
signal/signalfd: Add support for SIGSYS
signal/signalfd: Remove __put_user from signalfd_copyinfo
signal/xtensa: Use force_sig_fault where appropriate
signal/xtensa: Consistenly use SIGBUS in do_unaligned_user
signal/um: Use force_sig_fault where appropriate
signal/sparc: Use force_sig_fault where appropriate
signal/sparc: Use send_sig_fault where appropriate
signal/sh: Use force_sig_fault where appropriate
signal/s390: Use force_sig_fault where appropriate
signal/riscv: Replace do_trap_siginfo with force_sig_fault
signal/riscv: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_mceerr where appropriate
signal/openrisc: Use force_sig_fault where appropriate
signal/nios2: Use force_sig_fault where appropriate
...
Mark Rutland