Add support for the built-in touchscreen controller in DA9034
(aka Micco), usually found on platforms with xscale processors.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add clock framework support to the sh_mobile keysc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This drive has been tested on ARM9 based SoC - MV86XX.
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The HPGK touchpad that is found on the XO driver has historically
exhibitted eratic behaviour in various environments (very dry,
very humid, etc) that can be worked around via some delays. This
patch turns those delays into module parameters to make testing
simpler.
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Acked-By: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes the key repeat issue with the Fn+F? keys on the new
Samsung NC10 Netbook, so that the keys can be defined and used within
ACPID correctly, otherwise the keys repeat indefinately.
This solves part of http://bugzilla.kernel.org/show_bug.cgi?id=12021
Signed-off-by: Stuart Hopkins <stuart@dodgy-geeza.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add quirk for misbehaving volume buttons on HP Pavilion ZV6100 laptop which
are not sending keyrelease events, as reported by Aaron Pickett.
Signed-off-by: Rikard Ljungstrand <lrikard@student.chalmers.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Have most uses of OMAP_GPIO_IRQ() use gpio_to_irq() instead.
Calls used for table initialization are left alone, at least
this time around.
(This patch is for code in both the OMAP tree and mainline.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add support for new USB Tablet PCs
Input: replace spin_lock_bh with spin_lock_irqsave in ml_ff_playback
Input: i8042 - add Compal Hel80 laptop to nomux blacklist
Input: cm109 - add keymap for ATCom AU-100 phone
Input: fix the example of an input device driver
Input: psmouse - fix incorrect validate_byte check in OLPC protocol
Input: atkbd - cancel delayed work before freeing its structure
Input: atkbd - add keymap quirk for Inventec Symphony systems
Input: i8042 - add Dell XPS M1530 to nomux list
Input: elo - fix format string in elo driver
ml_ff_playback() uses spin_(un)lock_bh. However this function is called
with interrupts disabled from erase_effect() in drivers/input/ff-core.c:196.
This is not permitted, and will result in a WARN_ON in the bottom half handling code.
This patch changes this function to just use spin_lock_irqsave() instead, solving
the problem and simplifying the locking logic.
This was reported as entry #106559 in kerneloops.org
Reported-by: kerneloops.org
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... by giving the instances' names magic suffix recognized by modpost ;-/
Their ->probe() is __devinit
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CLPS7500 platform has not built since 2.6.22-git7 and there
seems to be no interest in fixing it. So, remove the platform
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Impact: cleanup, move all hrtimer processing into hardirq context
This is an attempt at removing some of the hrtimer complexity by
reducing the number of callback modes to 1.
This means that all hrtimer callback functions will be ran from HARD-irq
context.
I went through all the 30 odd hrtimer callback functions in the kernel
and saw only one that I'm not quite sure of, which is the one in
net/can/bcm.c - hence I'm CC-ing the folks responsible for that code.
Furthermore, the hrtimer core now calls callbacks directly with IRQs
disabled in case you try to enqueue an expired timer. If this timer is a
periodic timer (which should use hrtimer_forward() to advance its time)
then it might be possible to end up in an inf. recursive loop due to the
fact that hrtimer_forward() doesn't round up to the next timer
granularity, and therefore keeps on calling the callback - obviously
this needs a fix.
Aside from that, this seems to compile and actually boot on my dual core
test box - although I'm sure there are some bugs in, me not hitting any
makes me certain :-)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Wacom W8001 sensor is a sensor device (uses electromagnetic
resonance) and it is interfaced via its serial microcontroller
to the host.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ml_ff_playback() uses spin_(un)lock_bh. However this function is
called with interrupts disabled from erase_effect() in
drivers/input/ff-core.c:196.
This is not permitted, and will result in a WARN_ON in the bottom
half handling code. This patch changes this function to just use
spin_lock_irqsave() instead, solving the problem and simplifying
the locking logic.
This was reported as entry #106559 in kerneloops.org
Reported-by: kerneloops.org
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
According to Section 2.4.4 of the Synaptics TouchPad Interfacing
Guide, bit 2 specifies if multi-finger detection is provided by
the touchpad. Thus, only set BTN_TOOL_DOUBLETAP and
BTN_TOOL_TRIPLETAP if the device actually supports it.
Signed-off-by: Peter Hutterer <peter.hutterer@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The usbtouchscreen module implements a driver for the TSC-10 DM USB
touchscreen controllers, but assumes a 2-byte response for the
CMD_RESET and CMD_RATE commands, when they can be only a single byte
when no EEPROM is connected.
The driver worked with an earlier controller revision, but new
revisions of the controller fail.
It seems the problem is that the early controller had the
SEL4/EEPROM-CS pin high, but the new controller has it down, making
the response different.
Without the fix, the controller would answer the single byte 0x06
(ACK), making the init fail with -ENODEV because buf[1] is 0xFF (as
initialized before).
As the single byte is the only thing we need to check it was ok, there
is no need to verify the second byte.
The [0x15 0x01] case is the NAK [0x15] response for when there is no
data in the EEPROM [bit-0 of second byte set], so I let that be, as I
don't have any controller with an EEPROM.
With this patch, both the earlier and latest controller work the same.
Note: This was previously submited as BUG #11961 [1] on the bugzilla
tracker, but rebased to version 2.6.27.4 and with unnecessary comments
and printk's removed.
[1] http://bugzilla.kernel.org/show_bug.cgi?id=11961
Signed-off-by: Nuno Lucas <ntlucas@gmail.com>
Acked-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The validate_byte check logic was backwards; it should return true for
an *invalid* packet. Thanks to Jeremy Katz for spotting this one.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Pointed out by Oleg Nesterov. Since delayed work is used here, use of
flush_scheduled_work() is not sufficient in atkbd_disconnect(). It does
not wait for scheduled delayed work to finish. This patch prevents
delayed work to be processed after freeing atkbd structure (used struct
delayed_work is part of atkbd) by cancelling this delayed work.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Zepto 6615WD laptop (rebranded Inventec Symphony system) needs a
key release quirk for its volume keys to work. The attached patch adds
the quirk to the atkbd driver.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=460237
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dell XPS M1530 needs i8042.nomux=1 for ALPS touchpad to work as
reported on https://qa.mandriva.com/show_bug.cgi?id=43532
It is said that before A08 bios version this isn't needed (I don't
have the hardware so can't check), and suppose this will not break
with bios versions before A08.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Andreas Ericsson <ae@op5.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no reason to limit the GPIO rows to 6 for OMAP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The GPIO interrupts are disabled several times after the first key press.
No need to disable - again - the interrupts in the omap_kp_scan_keypad
function on OMAP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The appletouch driver has grown up from supporting only a couple of
touchpads into supporting many touchpads, which can have different
number of sensors, different aspect ratios etc.
This patch cleans up the current driver code and makes it easy to
support the features of each different touchpad.
As a side effect, this patch also modifies the 'Y' multiplication factor
of the 'geyser3' and 'geyser4' touchpads (found on Core Duo and Core2
Duo MacBook and MacBook Pro laptops) in order to make the touchpad
output match the aspect ratio of the touchpad (Y factor changed from 43
to 64).
[dtor@mail.ru: make atp_info constant]
Signed-off-by: Stelian Pop <stelian@popies.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a flag to gpio-key driver to turn on the input subsystems
auto repeat feature if needed.
Signed-off-by: Dominic Curran <dcurran@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Review comments were incorporated to improve the driver.
1. Some data was eliminated that was not needed.
2. Renaming of variables for clarity.
3. Removed unneeded type casting.
4. Changed to use dev_err rather than other I/O.
5. Merged together some functions.
6. Added kerneldoc format to functions.
Signed-off-by: Sadanand <sadanan@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, evdev has working 32bit compatibility and uinput does not. uinput
needs the input_event code that evdev uses, so let's refactor it so it can
be shared.
[dtor@mail.ru: add fix for force feedback compat issues]
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The SGI Volume Button interface driver uses GPL-only symbols
platform_driver_unregister and platform_driver_register, but
lacks license specification. Thus, when compiled as a module,
this driver cannot be installed. This patch fixes this by
adding the MODULE_LICENSE() specification.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - add support for Elantech touchpads
Input: i8042 - add Blue FB5601 to noloop exception table
Separate building of corgi_ssp.c, and introduce a new hidden config option
CONFIG_CORGI_SSP_DEPRECATED for this. Aslo mark corgi_ts.c and corgi_bl.c
as deprecated.
This unbreaks the legacy configs in {corgi,spitz}_defconfig, however, SPI
based ADS7846 touchscreen driver and a new SPI-based corgi_lcd.c driver
with integrated backlight support are recommended.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* 'for-next' of git://git.o-hand.com/linux-mfd:
mfd: further unbork the ucb1400 ac97_bus dependencies
mfd: ucb1400 needs GPIO
mfd: ucb1400 sound driver uses/depends on AC97_BUS:
mfd: Don't use NO_IRQ in WM8350
mfd: update TMIO drivers to use the clock API
mfd: twl4030-core irq simplification
mfd: add base support for Dialog DA9030/DA9034 PMICs
mfd: TWL4030 core driver
mfd: support tmiofb cell on tc6393xb
mfd: add OHCI cell to tc6393xb
mfd: Fix htc-egpio compile warning
mfd: do tcb6393xb state restore on resume only if requested
mfd: provide and use setup hook for tc6393xb
mfd: update sm501 debugging/low information messages
mfd: reduce stack usage in mfd-core.c
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is version 5 of the driver. Relative mode support has been
dropped (users wishing to use touchpad in relative mode can use
standard PS/2 protocol emulation done in hardware). The driver
supports both original version of Elantech protocol and the newer
one used by touchpads installed in EeePC.
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (32 commits)
Input: wm97xx - update email address for Liam Girdwood
Input: i8042 - add Thinkpad R31 to nomux list
Input: move map_to_7segment.h to include/linux
Input: ads7846 - fix cache line sharing issue
Input: cm109 - add missing newlines to messages
Input: document i8042.debug in kernel-parameters.txt
Input: keyboard - fix potential out of bound access to key_map
Input: psmouse - add OLPC touchpad driver
Input: psmouse - tweak PSMOUSE_DEFINE_ATTR to support raw set callbacks
Input: psmouse - add psmouse_queue_work() for ps/2 extension to make use of
Input: psmouse - export psmouse_set_state for ps/2 extensions to use
Input: ads7846 - introduce .gpio_pendown to get pendown state
Input: ALPS - add signature for DualPoint found in Dell Latitude E6500
Input: serio_raw - allow attaching to translated (SERIO_I8042XL) ports
Input: cm109 - don't use obsolete logging macros
Input: atkbd - expand Latitude's force release quirk to other Dells
Input: bf54x-keys - add power management support
Input: atmel_tsadcc - improve accuracy
Input: convert drivers to use strict_strtoul()
Input: appletouch - handle geyser 3/4 status bits
...
This updates most of the OMAP drivers which are in mainline to switch to
using the cross-platform GPIO calls instead of the older OMAP-specific
ones.
This is all fairly brainless/obvious stuff. Probably the most interesting
bit is to observe that the omap-keypad code seems to now have a portable
core that could work with non-OMAP matrix keypads. (That would improve
with hardware IRQ debouncing enabled, of course...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kill compiler warnings related to printf() formats in the input drivers for
various HP9000 machines, which are shared between PA-RISC (suseconds_t is int)
and m68k (suseconds_t is long). As both are 32-bit, it's safe to cast to int.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This updates the email address for Liam Girdwood as my old address is no
longer valid.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Thinkpad R31 needs i8042 nomux quirk. Stops jittery jumping mouse
and random keyboard input. Fixes kernel bug #11723. Cherry picked
from Ubuntu who have sometimes (on-again-off-again) had a fix in
their patched kernels.
Signed-off-by: Colin B Macdonald <cbm@m.fsf.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This merges in:
x86/build, x86/microcode, x86/spinlocks, x86/memory-corruption-check,
x86/early-printk, x86/xsave, x86/quirks, x86/setup, x86/signal,
core/signal, x86/urgent, x86/xen
* 'x86-core-v2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (142 commits)
x86: make processor type select depend on CONFIG_EMBEDDED
x86: extend processor type select help text
x86, amd-iommu: propagate PCI device enabling error
warnings: fix arch/x86/kernel/io_apic_64.c
warnings: fix arch/x86/kernel/early_printk.c
x86, fpu: check __clear_user() return value
x86: memory corruption check - cleanup
x86: ioperm user_regset
xen: do not reserve 2 pages of padding between hypervisor and fixmap.
xen: use spin_lock_nest_lock when pinning a pagetable
x86: xsave: set FP, SSE bits in the xsave header in the user sigcontext
x86: xsave: fix error condition in save_i387_xstate()
x86: SB450: deprioritize DMI quirks
x86: SB450: skip IRQ0 override if it is not routed to INT2 of IOAPIC
x86: replace a magic number with a named constant in the VESA boot code
x86 setup: remove IMAGE_OFFSET
x86 setup: remove DEF_INITSEG and DEF_SETUPSEG
Revert "x86: fix ghost EDD devices in /sys again"
x86 setup: fix ghost entries under /sys/firmware/edd take 3
x86: signal: remove indent in restore_sigcontext()
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
The map_to_7segment.h provides generic 7segment LED mappings and is
designed to be used by other drivers. Moving it to common area will
make it more usable. Also exporting it to userspace will help users
of sysfs interface.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Henk Vergonet <henk.vergonet@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We had a report a while back that the ads7846 driver had some issues
when used with DMA-based SPI controllers (like atmel_spi) on systems
where main memory is not DMA-coherent (most non-x86 boards). Allocate
memory potentially used for DMA separately to avoid cache line issues.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Recent conversion from err(), warn(), info() to dev_* variants caused loss
of newlines at the end of messages, add them back.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: jornada720_ts - fix build error ( LONG() usage )
Input: bcm5974 - switch back to normal mode when closing
This adds support for OLPC's touchpad. It has lots of neat features,
none of which are enabled because the hardware is too buggy. Instead,
we use it like a normal touchpad, but with a number of workarounds in
place to deal with the frequent hardware spasms. Humidity changes,
sweat, tinfoil underwear, plugging in AC, drinks, evil felines.. All
tend to cause the touchpad to freak out.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We want to support attr->set callbacks that may need psmouse->state to
not be updated, or may want to manually deal w/ enabling and disabling
the device. To do that, we create __PSMOUSE_DEFINE_ATTR which enables
us to set a 'protect' argument specifying whether or not the set
callback should be protected with psmouse_disable and state setting.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
psmouse_queue_work is passed a delayed_work struct, and queues up the work
with kpsmouse_wq. Since we're dealing with delayed_work stuff, this
also switches resync_work to a delayed_work struct as well, and makes
use of psmouse_queue_work when doing a resync within psmouse-base.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The GPIO connected to ADS7846 nPENIRQ signal is usually used to get
the pendown state as well. Introduce a .gpio_pendown, and use this
to decide the pendown state if .get_pendown_state is NULL.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch removes the usage of LONG() which is deprecated; we also
replace BIT() with BIT_MASK().
signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Staying in multi-touch mode after closing the device sometimes makes
the keyboard drop keys or repeat keys irratically. The conjecture is
that some internal buffer starts to overflow, resulting in undefined
behavior. Switching back to normal mode when closing the device makes
the problem go away.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The GPIO connected to ADS7846 nPENIRQ signal is usually used to get
the pendown state as well. Introduce a .gpio_pendown, and use this
to decide the pendown state if .get_pendown_state is NULL.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
serio_raw only binds to non-translated devices. Enable serio_raw to
bind to normal (translated) keyboards which can have non-standard
extensions (like POS Keyboards). With this it is possible to send
commands to the device over /dev/serio_raw<n>.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
err(), warn(), info() are being removed in favor of dev_* variants.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dell laptops fail to send key up events for several of their special
keys. There's an existing quirk in the kernel to handle this, but it's
limited to the Latitude range. This patch extends it to cover all
portable Dells.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix Bug: does nor properply resume after suspend mem
Fix for PM_SUSPEND_MEM: Save and restore peripheral base registers
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Discard the last sample just before pen is up because it is quite often
errorneous.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Liang <dan.liang@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
strict_strtoul() allows newline character at the end of the the input
string and therefore is more user-friendly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Apparently, there are more different versions of Lenovo 3000 N100, some
of them working properly with active mux, and some of them requiring it
being switched off.
This patch applies 'nomux' only to the specific product name that is
reported to behave badly unless 'nomux' is specified.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The mousedev driver requires the use of BTN_TOUCH events to process
ABS_X and ABS_Y events properly, which is what is needed for the
bcm5974-based apple computers to have a functional pointer out-of-the-box.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The problem of finger tracking, i.e., when to switch focus from one
finger to another on the trackpad, has been improved by utilizing more
information from the bcm5974 chip output. This results in less pointer
hopping when many fingers are on the trackpad. In addition, a finger
counting method based on pressure information from all fingers is
introduced. Together with a pressure hysteresis window, this yields a
more stable counting of the number of fingers on the trackpad.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch splits ucb1400_ts into ucb1400_ts and ucb1400_core.
Since this chip supports more features than only touchscreen,
it was necessary to prepare it for feature addition. The
previous functionality is preserved by applying this patch.
[Build fixes for non-ARM by Stephen Rothwell and Takashi Iwai]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are four operating modes Xen code may find itself running in:
- native
- hvm domain
- pv dom0
- pv domU
Clean up predicates for testing for these states to make them more consistent.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: evdev - fix printf() format for sizeof
Input: remove version.h from drivers that don't need it
Input: cobalt_btns - add missing MODULE_LICENSE
commit f2afa7711f ("Input: paper over a bug in
Synaptics X driver") introduced a compiler warning on 64-bit platforms, as
sizeof() returns a size_t, not an (unsigned) int:
| drivers/input/evdev.c: In function 'handle_eviocgbit':
| drivers/input/evdev.c:684: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
Use the proper `z' modifier for size_t, and make the printf() formats for the
sizes unsigned while we're at it.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If a driver dies not use LINUX_VERSION_CODE nor KERNEL_VERSION
then it does not need to include version.h
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Export the module license and other information about the Cobalt
button module in order to avoid the following warning:
| WARNING: modpost: missing MODULE_LICENSE() in drivers/input/misc/cobalt_btns.o
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xilinx_ps2 - fix warning
Input: bcm5974 - implement autosuspend support
Input: bcm5974 - add driver for Macbook Air and Pro Penryn touchpads
Input: paper over a bug in Synaptics X driver
Input: evdev - split EVIOCGBIT handlig into a separate function
Input: i8042 - Add Dritek quirk for Acer TravelMate 4280
Input: xpad - add Pelican Eclipse D-Pad to the list of devices
Input: gpio-keys - make gpio_keys_device_driver static
Input: gpio-keys - fix possible NULL pointer dereference
Input: wm97xx - enable sub-drivers by default
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Handle stack trace attempts before irqstacks are setup.
sparc64: Implement IRQ stacks.
sparc: remove include of linux/of_device.h from asm/of_device.h
sparc64: Fix recursion in stack overflow detection handling.
sparc/drivers: use linux/of_device.h instead of asm/of_device.h
sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code.
The i2c layer got changed while the migor_ts driver was in the input
tree waiting to get merged upstream. Fix current compile issue by using
struct i2c_client member "name" instead of "driver_name". Also, add
id_table to make sure the device gets properly detected.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
drivers/input/serio/xilinx_ps2.c:272: warning: cast from pointer
to integer of different size
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Implement support for status bits on Geyser 3/4.
Signed-off-by: Sven Anders <anders@anduras.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Split complete function into separate functions for GEYSER1/2 and GEYSER 3/4.
Signed-off-by: Sven Anders <anders@anduras.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver adds support for the multitouch trackpad on the new
Apple Macbook Air and Macbook Pro Penryn laptops. It replaces the
appletouch driver on those computers, and integrates well with the
synaptics driver of the Xorg system.
[dtor@mail.ru: various cleanups]
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5177/1: arm/mach-sa1100/Makefile: remove CONFIG_SA1100_USB
[ARM] 5166/1: magician: add MAINTAINERS entry
[ARM] fix pnx4008 build errors
[ARM] Fix SMP booting with non-zero PHYS_OFFSET
[ARM] 5185/1: Fix spi num_chipselect for lubbock
[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
[ARM] Add support for arch/arm/mach-*/include and arch/arm/plat-*/include
[ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
[ARM] Eliminate useless includes of asm/mach-types.h
[ARM] Fix circular include dependency with IRQ headers
avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
avr32: Introduce arch/avr32/mach-*/include/mach
avr32: Move include/asm-avr32 to arch/avr32/include/asm
[ARM] sa1100_wdt: use reset_status to remember watchdog reset status
[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage
[ARM] pxa: introduce reset.h for reset specific header information
For now this only saves a few instructions (for gpio_keys_report_event,
gpio_keys_isr and gpio_check_button one instraction each on ARM using
arm-linux-gnu-gcc 4.2.3---I assume this is similar for other arch/compiler
combinations).
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
By passing a gpio_button_data structure to the handler instead of the
whole platform_device the search for the right button can go away.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/input/serio/i8042-sparcio.h:95: warning: 'sparc_i8042_driver'
defined but not used
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can simply wrap in to the dev_set/get_drvdata(), there's no reason
to track an extra level of private data on top of the struct device.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were completely inconsistent. Clean these up to take a maple_driver
pointer directly for consistency.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Have a single probe function instead of a probe and a connect function.
Also tidy a comment.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Allow the removal (and subsequent reinsertion) of the maple_keyb (maple
keyboard) driver by adding a working removal function.
Also tidy long lines.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes the sparse warning
symbol 'gpio_keys_device_driver' was not declared. Should it be static?
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
bdata->button is used in gpio_check_button but never initialized. Having a
device with debounce_interval != 0 without this patch resulted on an oops on
my machine.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Support for loadable keymaps. The driver now supports individual
keymaps for each of the five modes (AUX1-AUX4 and PC) of the
remote. To achieve this the keymap scancode is interpreted as a
combination of the mode and actual button scancode. The original
keycode patches were done by Peter Stokes <linux@dadeos.co.uk>
but I modified it quite a lot.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Perform actual driver registration right in gameport_register_driver()
instead of offloading it to kgameportd and return proper error code to
callers if driver registration fails.
Note that driver <-> port matching is still done by kgameportd.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently the support for each WM97xx touchscreen model is compiled out
by default, meaning that the default configuration when the driver is
built is for it to support no hardware. This is suboptimal and leads to
problems like distribution kernels shipping a non-functional driver.
Change the default to support all controllers and update the help text
to reflect this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
