Currently, AXP803 driver assumes that reg_drivevbus is input which is
wrong. Unfortunate consequence of that is that none of the USB ports
work on the board, even USB HOST port, because USB PHY driver probing
fails due to missing regulator.
Fix that by adding "x-powers,drive-vbus-en" property to AXP803 node.
Fixes: 14ff5d8f91 ("arm64: dts: allwinner: a64: Orange Pi Win: Enable USB OTG socket")
Cc: stable@vger.kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable all necessary device tree nodes and add connector node to device
trees for all supported A64 boards with HDMI.
Jagan, tested on BPI-M64, OPI-Win, A64-Olinuxino, NPI-A64
Vasily, tested on pine64-lts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: squash all board patches altogether and change supply name]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pinmux name and label for a specific function should denote which
pingroup it is on, or if there is only one option for the function, have
not enumerating prefix/suffix at all.
The "uart0_pins_a" label is renamed to "uart0_pb_pins" to fit our
current style. The node name "uart0" is also changed to "uart0-pb-pins"
to match.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win board uses the AXP's ALDO1 power rail to drive the
VCC-CSI line, which, according to the schematic, needs to be set to 2.8V.
Also the ELDO3 power rail is connected to the CSI, with somewhat unclear
voltage requirements. Add this regulator and allow the voltage to be set
between 1.5V and 1.8V, which are the voltages mentioned in the
schematic.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win comes with 2 MB SPI flash, add the node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win features a soldered WiFi chip on the board, connected
via the SDIO interface. Add the required DT nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a green status LED, add the DT node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win exposes several UARTs on header pins, and connects one
to the on-board WiFi/Bluetooth chip.
Add the pinmux definitions to the UART nodes, but keep them disabled.
Enable the UART1, which is wired to the Bluetooth chip, and add a serdev
node. There is no binding for the BT8723 yet, so leave this mostly empty
for now.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has the usual Gigabit PHY connected to the EMAC.
Its power is controlled by GPIO PD14.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a micro USB-B socket, connected to the SoC's
USB-OTG port. Its power is supplied by the AXP PMIC, and the ID pin is
connected to GPIO PH9. It can serve both as a host or a client port.
Add the respective DT nodes to enable it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: enable paired EHCI/OHCI device nodes and regulator supply]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has four standard USB-A sockets, connected to an
on-board USB hub. The hub's and socket's power regulators are enabled by
GPIO PD7.
Add the regulator to the DT to enable the power supply.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a microSD card slot which is connected via all
four SD data lines. As the DT was not mentioning this fact, we got the
default single bit transfers, losing out on performance.
Also, as microSD does not have a write protect switch, we disable this
feature in the DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
On usual A64 board design the power of HDMI controller is connected to
DLDO1 of the AXP803 PMIC. If this regulator is shut down, the HDMI
output will be blank. Therefore the simplefb driver should keep this
regulator on.
Add the regulator to all currently available A64 boards' simplefb_hdmi
device node, if the board is capable of outputing HDMI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable AXP803 PMIC and regulators for Orangepi Win.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.
A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>