The DWMAC binding never supported having the Ethernet PHY node as a
direct child to the controller, nor did it support the "phy" property
as a way to specify which Ethernet PHY to use. What seemed to work
was simply the implementation ignoring the "phy" property and instead
probing all addresses on the MDIO bus and using the first available
one.
The recent switch from "phy" to "phy-handle" breaks the assumptions
of the implementation, and does not match what the binding requires.
The binding requires that if an MDIO bus is described, it shall be
a sub-node with the "snps,dwmac-mdio" compatible string.
Add a device node for the MDIO bus, and move the Ethernet PHY node
under it. Also fix up the #address-cells and #size-cells properties
where needed.
Fixes: de332de26d ("ARM: dts: sunxi: Switch from phy to phy-handle")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The phy device tree property has been deprecated in favor of phy-handle,
let's replace it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The I7 DTS uses an spdif-out property with an "okay" value. However, that
property isn't documented anywhere, and isn't used anywhere either.
Remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
-----BEGIN PGP SIGNATURE-----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=hXvM
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard:
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
* tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus
ARM: dts: sun8i-h3: Add Mali node
ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards
ARM: dts: sun8i: h3: Enable HDMI output on H3 boards
ARM: dts: sunxi: h3/h5: Add HDMI pipeline
ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node
ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi
ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl
ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
ARM: dts: nanopi-neo-air: Add WiFi / eMMC
The Mele I7 has an HDMI connector wired to the HDMI pins
on the SoC. Enable the display pipeline and HDMI output.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Added "dts" prefix]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the S/PDIF transmitter that is present on the Mele I7.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele I7 has an audio jack for the SoC's internal codec.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).
Remove these properties to make it obvious that we do not set anything in
such a case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.
Remove it from our DT, as suggested.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.
While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele I7 is a Allwinner A31 based Android TV box, with 1G RAM,
8GB NAND flash, a RTL8188etv wifi chip, 3 USB Host ports using
USB-A receptacles, a micro USB-B receptacle for USB OTG, HDMI out,
a TRS connector for A/V, SPDIF and IrDA.
This patch adds basic support for the device, more information can
be found here (http://linux-sunxi.org/Mele_I7).
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai