This fixes a bug where it is possible for an off-line CPU to fail to go
into a low-power state (nap/sleep/winkle), and to become unresponsive to
requests from the KVM subsystem to wake up and run a VCPU. What can
happen is that a maskable interrupt of some kind (external, decrementer,
hypervisor doorbell, or HMI) after we have called local_irq_disable() at
the beginning of pnv_smp_cpu_kill_self() and before interrupts are
hard-disabled inside power7_nap/sleep/winkle(). In this situation, the
pending event is marked in the irq_happened flag in the PACA. This
pending event prevents power7_nap/sleep/winkle from going to the
requested low-power state; instead they return immediately. We don't
deal with any of these pending event flags in the off-line loop in
pnv_smp_cpu_kill_self() because power7_nap et al. return 0 in this case,
so we will have srr1 == 0, and none of the processing to clear
interrupts or doorbells will be done.
Usually, the most obvious symptom of this is that a KVM guest will fail
with a console message saying "KVM: couldn't grab cpu N".
This fixes the problem by making sure we handle the irq_happened flags
properly. First, we hard-disable before the off-line loop. Once we have
hard-disabled, the irq_happened flags can't change underneath us. We
unconditionally clear the DEC and HMI flags: there is no processing of
timer interrupts while off-line, and the necessary HMI processing is all
done in lower-level code. We leave the EE and DBELL flags alone for the
first iteration of the loop, so that we won't fail to respond to a
split-core request that came in just before hard-disabling. Within the
loop, we handle external interrupts if the EE bit is set in irq_happened
as well as if the low-power state was interrupted by an external
interrupt. (We don't need to do the msgclr for a pending doorbell in
irq_happened, because doorbells are edge-triggered and don't remain
pending in hardware.) Then we clear both the EE and DBELL flags, and
once clear, they cannot be set again (until this CPU comes online again,
that is).
This also fixes the debug check to not be done when we just ran a KVM
guest or when the sleep didn't happen because of a pending event in
irq_happened.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit 9678cdaae9 ("Use the POWER8 Micro Partition
Prefetch Engine in KVM HV on POWER8") because the original commit had
multiple, partly self-cancelling bugs, that could cause occasional
memory corruption.
In fact the logmpp instruction was incorrectly using register r0 as the
source of the buffer address and operation code, and depending on what
was in r0, it would either do nothing or corrupt the 64k page pointed to
by r0.
The logmpp instruction encoding and the operation code definitions could
be corrected, but then there is the problem that there is no clearly
defined way to know when the hardware has finished writing to the
buffer.
The original commit attempted to work around this by aborting the
write-out before starting the prefetch, but this is ineffective in the
case where the virtual core is now executing on a different physical
core from the one where the write-out was initiated.
These problems plus advice from the hardware designers not to use the
function (since the measured performance improvement from using the
feature was actually mostly negative), mean that reverting the code is
the best option.
Fixes: 9678cdaae9 ("Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8")
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Similar to commit b6541db ("powerpc/eeh: Block PCI config access
upon frozen PE"), this blocks the PCI config space of Broadcom
Shiner adapter until PE reset is completed, to avoid recursive
fenced PHB when dumping PCI config registers during the period
of error recovery.
~# lspci -ns 0003:03:00.0
0003:03:00.0 0200: 14e4:168a (rev 10)
~# lspci -s 0003:03:00.0
0003:03:00.0 Ethernet controller: Broadcom Corporation \
NetXtreme II BCM57800 1/10 Gigabit Ethernet (rev 10)
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This simplifies pnv_eeh_set_option() to avoid unnecessary nested
if statements, to improve readability. No functional changes.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the logic of pnv_eeh_cap_start() to pnv_eeh_find_cap()
as the function is only called by pnv_eeh_find_cap(). The logic
of both functions are pretty simple. No need to have separate
functions.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This cleans up pseries_eeh_get_state(), no functional changes:
* Return EEH_STATE_NOT_SUPPORT early when the 2nd RTAS output
argument is zero to avoid nested if statements.
* Skip clearing bits in the PE state represented by variable
"result" to simplify the code.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When one or both of the below two flags are marked in the PE state, the
PE's IO path is regarded as enabled: EEH_STATE_MMIO_ACTIVE or
EEH_STATE_MMIO_ENABLED.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On fenced PHB, the error handlers in the drivers of its subordinate
devices could return PCI_ERS_RESULT_CAN_RECOVER, indicating no reset
will be issued during the recovery. It's conflicting with the fact
that fenced PHB won't be recovered without reset.
This limits the return value from the error handlers in the drivers
of the fenced PHB's subordinate devices to PCI_ERS_RESULT_NEED_NONE
or PCI_ERS_RESULT_NEED_RESET, to ensure reset will be issued during
recovery.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, we rely on the existence of struct pci_driver::err_handler
to decide if the corresponding PCI device should be unplugged during
EEH recovery (partially hotplug case). However that check is not
sufficient. Some device drivers implement only some of the EEH error
handlers to collect diag-data. That means the driver still expects a
hotplug to recover from the EEH error.
This makes the hotplug criterion more relaxed: if the device driver
doesn't provide all necessary EEH error handlers, it will experience
hotplug during EEH recovery.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
[mpe: Minor change log rewording]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On PowerNV platform, the PE is kept in frozen state until the PE
reset is completed to avoid recursive EEH error caused by MMIO
access during the period of EEH reset. The PE's frozen state is
cleared after BARs of PCI device included in the PE are restored
and enabled. However, we needn't clear the frozen state for PHB PE
explicitly at this point as there is no real PE for PHB PE. As the
PHB PE is always binding with PE#0, we actually clear PE#0, which
is wrong. It doesn't incur any problem though.
This checks if the PE is PHB PE and doesn't clear the frozen state
if it is.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a boot wrapper script function run_cmd which will run a shell command
quietly and only print the output if either V=1 or an error occurs.
Also, run the ps3 dd commands with run_cmd to clean up the build output.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently a CPU running a guest can receive a H_DOORBELL in the
following two cases:
1) When the CPU is napping due to CEDE or there not being a guest
vcpu.
2) The CPU is running the guest vcpu.
Case 1), the doorbell message is not cleared since we were waking up
from nap. Hence when the EE bit gets set on transition from guest to
host, the H_DOORBELL interrupt is delivered to the host and the
corresponding handler is invoked.
However in Case 2), the message gets cleared by the action of taking
the H_DOORBELL interrupt. Since the CPU was running a guest, instead
of invoking the doorbell handler, the code invokes the second-level
interrupt handler to switch the context from the guest to the host. At
this point the setting of the EE bit doesn't result in the CPU getting
the doorbell interrupt since it has already been delivered once. So,
the handler for this doorbell is never invoked!
This causes softlockups if the missed DOORBELL was an IPI sent from a
sibling subcore on the same CPU.
This patch fixes it by explitly invoking the doorbell handler on the
exit path if the exit reason is H_DOORBELL similar to the way an
EXTERNAL interrupt is handled. Since this will also handle Case 1), we
can unconditionally clear the doorbell message in
kvmppc_check_wake_reason.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
QEMU assumes 32 memslots if this extension is not implemented. Although,
current value of KVM_USER_MEM_SLOTS is 32, once KVM_USER_MEM_SLOTS
changes QEMU would take a wrong value.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a bug where the old HPTE value returned by H_REMOVE has
the valid bit clear if the HPTE was an absent HPTE, as happens for
HPTEs for emulated MMIO pages and for RAM pages that have been paged
out by the host. If the absent bit is set, we clear it and set the
valid bit, because from the guest's point of view, the HPTE is valid.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the KVM_PPC_ALLOCATE_HTAB will try to allocate the requested
size of HPT, and if that is not possible, then try to allocate smaller
sizes (by factors of 2) until either a minimum is reached or the
allocation succeeds. This is not ideal for userspace, particularly in
migration scenarios, where the destination VM really does require the
size requested. Also, the minimum HPT size of 256kB may be
insufficient for the guest to run successfully.
This removes the fallback to smaller sizes on allocation failure for
the KVM_PPC_ALLOCATE_HTAB ioctl. The fallback still exists for the
case where the HPT is allocated at the time the first VCPU is run, if
no HPT has been allocated by ioctl by that time.
Signed-off-by: Paul Mackerras <paulus@samba.org>
of_get_property() is used inside the loop, but then the reference to the
node is dropped before dereferencing the prop pointer, which could by then
point to junk if the node has been freed.
Instead use of_property_read_u32() to actually read the property
value before dropping the reference.
of_property_read_u32() requires at least one cell (u32) to be present,
which is stricter than the old logic which would happily dereference a
property of any size. However we believe all device trees in the wild
have at least one cell.
Skiboot may produce memory nodes with more than one cell, but that is
OK, of_property_read_u32() will return the first one.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[mpe: Expand change log with device tree details]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch catches PERF_SAMPLE_BRANCH_CALL because it is not clear whether
this is actually supported by the hardware.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: khandual@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1444720151-10275-4-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The TUNE_CELL option allows you to build a kernel that runs on multiple
CPUs but is tuned (ie. optimised) to run on Cell CPUs. Now days no one
is building a distro in that fashion, and any users who are building
custom kernels for their Cell machines are better off building with
CONFIG_CELL_CPU, which builds a kernel that only runs on Cell and
therefore can be optimised even more aggresively.
Dropping the option also avoids confusing other users, who are presented
with an option to tune for Cell when they are not building for a Cell
CPU at all.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The OS should ask Power Firmware (PFW) for the size of the buffer
allocated for the event log, instead of the size of the actual
event log. It then passes the buffer adddress and size to PFW in
the handover process, into which PFW copies the log.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The event log generated by OpenFirmware in PowerPC is 4-byte aligned.
This patch reformats the log to be byte-aligned for the Linux client.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Replace all occurrences of '/ibm,vtpm' with '/vdevice/vtpm',
as only the latter is guanranteed to be available for the client OS.
The '/ibm,vtpm' node should only be used by Open Firmware, which
is susceptible to changes.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Otherwise, because the top end of the crash kernel is treated as the
absolute top of memory rather than the beginning of a reserved region,
in-flight DMA from the previous kernel that targets areas above the
crash kernel can trigger a storm of PCI errors. We only do this for
kdump, not normal kexec, in case kexec is being used to upgrade to a
kernel that wants a different inbound memory map.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Mingkai Hu <Mingkai.hu@freescale.com>
85xx currently uses the generic timebase sync mechanism when
CONFIG_KEXEC is enabled, because 32-bit 85xx kexec support does a hard
reset of each core. 64-bit 85xx kexec does not do this, so we neither
need nor want this (nor is the generic timebase sync code built on
ppc64).
FWIW, I don't like the fact that the hard reset is done on 32-bit
kexec, and I especially don't like the timebase sync being triggered
only on the presence of CONFIG_KEXEC rather than actually booting in
that environment, but that's beyond the scope of this patch...
Signed-off-by: Scott Wood <scottwood@freescale.com>
Problems have been observed in coreint (EPR) mode if interrupts are
left pending (due to the lack of device quiescence with kdump) after
having tried to deliver to a CPU but unable to deliver due to MSR[EE]
-- interrupts no longer get reliably delivered in the new kernel. I
tried various ways of fixing it up inside the crash kernel itself, and
none worked (including resetting the entire mpic). Masking all
interrupts and issuing EOIs in the crashing kernel did help a lot of
the time, but the behavior was not consistent.
Thus, stick to standard IACK mode when kdump is a possibility.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This allows SMP kernels to work as kdump crash kernels. While crash
kernels don't really need to be SMP, this prevents things from breaking
if a user does it anyway (which is not something you want to only find
out once the main kernel has crashed in the field, especially if
whether it works or not depends on which cpu crashed).
Signed-off-by: Scott Wood <scottwood@freescale.com>
To make provision for more than one L2 caches in the system, change the
name from L2 to L2_1; same as in T4 platforms.
* Also remove the L2 entry from common file
"arch/powerpc/boot/dts/fsl/b4si-post.dtsi"
Keep them only in separate files for b4860 and b4420.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
It makes no sense that some Freescale device tree files are in fsl
directory while some others not. This patch move Freescale device tree
files into fsl folder. To do that the following two steps are made:
- Move Freescale device tree files into fsl folder.
- Update the include path in these files from "fsl/*.dtsi" to "*.dtsi".
Please add "fsl/" prefix when you make dtb using Makefile.
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
[scottwood: fixed cuImage rule]
Signed-off-by: Scott Wood <scottwood@freescale.com>
In case of B4860 LIODN register for sRIO is not in GUTs block but in
the sRIO register space.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This board uses a P5020 chip, and boots just fine using
the corenet_generic code. The device tree is very similar to the
P5020DS, except that there is no Flash memory. The environment is,
instead, stored on an MMC card on the motherboard.
Signed-off-by: Andy Fleming <afleming@gmail.com>
[scottwood: fixed trailing whitespace]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hongtao Jia <hongtao.jia@freescale.com>
DS26522 is used for tdm, configured by SPI bus.
Add nodes under spi node to t104xd4rdb.dtsi.
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
While the handling of fsl,pq3-gpio and fsl,mpc8572-gpio is done in the
same driver and the two hardly differ, the latter controller needs a
workaround for an erratum in the gpio_get callback. To make this
difference more explicit remove fsl,pq3-gpio from the list of
compatibles for mpc8572 machines.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add 1588 timer node in files:
arch/powerpc/boot/dts/bsc9131rdb.dtsi
arch/powerpc/boot/dts/bsc9132qds.dtsi
arch/powerpc/boot/dts/p1010rdb.dtsi
arch/powerpc/boot/dts/p1020rdb-pd.dts
arch/powerpc/boot/dts/p1021rdb-pc.dtsi
arch/powerpc/boot/dts/p1022ds.dtsi
arch/powerpc/boot/dts/p1025twr.dtsi
For P2020RDB-PC, registers' values should be calculated
based on default 1588 reference clock(300MHz) not 250MHz,
and fix this in file:
arch/powerpc/boot/dts/p2020rdb-pc.dtsi
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Core reset may cause issue if using the proxy mode of MPIC.
Use the mixed mode of MPIC if enabling CPU hotplug.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3ze+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix build failure of load_unaligned_zeropad test
powerpc/powernv: Panic on unhandled Machine Check
powerpc: Fix checkstop in native_hpte_clear() with lockdep
cxl: Fix number of allocated pages in SPA
cxl: Workaround malformed pcie packets on some cards
cxl: fix leak of ctx->mapping when releasing kernel API contexts
cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
cxl: fix leak of IRQ names in cxl_free_afu_irqs()
powerpc/ps3: Remove unused os_area_db_id_video_mode
powerpc/configs: Re-enable CONFIG_SCSI_DH
For the machine check interrupt that happens while we are in the guest,
kvm layer attempts the recovery, and then delivers the machine check interrupt
directly to the guest if recovery fails. On successful recovery we go back to
normal functioning of the guest. But there can be cases where a machine check
interrupt can happen with MSR(RI=0) while we are in the guest. This means
MC interrupt is unrecoverable and we have to deliver a machine check to the
guest since the machine check interrupt might have trashed valid values in
SRR0/1. The current implementation do not handle this case, causing guest
to crash with Bad kernel stack pointer instead of machine check oops message.
[26281.490060] Bad kernel stack pointer 3fff9ccce5b0 at c00000000000490c
[26281.490434] Oops: Bad kernel stack pointer, sig: 6 [#1]
[26281.490472] SMP NR_CPUS=2048 NUMA pSeries
This patch fixes this issue by checking MSR(RI=0) in KVM layer and forwarding
unrecoverable interrupt to guest which then panics with proper machine check
Oops message.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The kernel log buffer is often much longer than the size of a terminal
so paginate it's output.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The paca display is already more than 24 lines, which can be problematic
if you have an old school 80x24 terminal, or more likely you are on a
virtual terminal which does not scroll for whatever reason.
This patch adds a new command "#", which takes a single (hex) numeric
argument: lines per page. It will cause the output of "dp" and "dpa"
to be broken into pages, if necessary.
Sample output:
0:mon> # 10
0:mon> dp1
paca for cpu 0x1 @ c00000000fdc0480:
possible = yes
present = yes
online = yes
lock_token = 0x8000 (0x8)
paca_index = 0x1 (0xa)
kernel_toc = 0xc000000000eb2400 (0x10)
kernelbase = 0xc000000000000000 (0x18)
kernel_msr = 0xb000000000001032 (0x20)
emergency_sp = 0xc00000003ffe8000 (0x28)
mc_emergency_sp = 0xc00000003ffe4000 (0x2e0)
in_mce = 0x0 (0x2e8)
data_offset = 0x7f170000 (0x30)
hw_cpu_id = 0x8 (0x38)
cpu_start = 0x1 (0x3a)
kexec_state = 0x0 (0x3b)
[Hit a key (a:all, q:truncate, any:next page)]
0:mon>
__current = 0xc00000007e696620 (0x290)
kstack = 0xc00000007e6ebe30 (0x298)
stab_rr = 0xb (0x2a0)
saved_r1 = 0xc00000007ef37860 (0x2a8)
trap_save = 0x0 (0x2b8)
soft_enabled = 0x0 (0x2ba)
irq_happened = 0x1 (0x2bb)
io_sync = 0x0 (0x2bc)
irq_work_pending = 0x0 (0x2bd)
nap_state_lost = 0x0 (0x2be)
0:mon>
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
[mpe: Use bool, make some variables static]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
of_get_next_parent can be used to simplify the while() loop and
avoid the need of a temp variable.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
of_get_next_parent can be used to simplify the while() loop and
avoid the need of a temp variable.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 3c8464a9b1 ("powerpc:
Delete old PrPMC 280/2800 support") we got rid of most of the C
code, and the Makefile/Kconfig hooks, but it seems I left the
platform's DTS file orphaned in the tree as well as the boot code.
Here we get rid of them both.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
.exit.text is discarded at run time and there are some references from
that to .exit.data, so we need to discard .exit.data at run time as well.
Fixes these errors:
`.exit.data' referenced in section `.exit.text' of drivers/built-in.o: defined in discarded section `.exit.data' of drivers/built-in.o
`.exit.data' referenced in section `.exit.text' of drivers/built-in.o: defined in discarded section `.exit.data' of drivers/built-in.o
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No need to have two atomic opertions (update and fetch/check) when
decreasing PE's number of passed devices as one atomic operation
is enough.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export pcibios_free_controller(), so it can be used by the cxl module to
free virtual PHBs.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch provides individual system call numbers for the following
System V IPC system calls, on PowerPC, so that they do not need to be
multiplexed:
* semop, semget, semctl, semtimedop
* msgsnd, msgrcv, msgget, msgctl
* shmat, shmdt, shmget, shmctl
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that pseries selects PCI_MSI && PCI, EEH will always be true, and
therefore CONFIG_PSERIES_MSI will always be true. So drop it, and move
msi.o to obj-y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make it entirely clear in the Makefile that we always build the pci
related files by moving them to obj-y.
Note that CONFIG_EEH is now always enabled on pseries, because it
depends on PSERIES && PCI.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we always have CONFIG_PCI=y for pseries, we can stop guarding
code with CONFIG_PCI ifdefs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pseries build with PCI=n looks to have been broken for at least 5
years, and no one's noticed or cared.
Following the obvious breakages backward, the first commit I can find
that builds is the parent of 2eb4afb69f ("powerpc/pci: Move pseries
code into pseries platform specific area") from April 2009.
A distro would never ship a PCI=n kernel, so it is only useful for folks
building custom kernels. Also on KVM the virtio devices appear on PCI,
so it would only be useful if you were building kernels specifically to
run on PowerVM and with no PCI devices.
The added code complexity, and testing load (which we've clearly not
been doing), is not justified by the small reduction in kernel size for
such a niche use case.
So just make PCI non-optional on pseries.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix couple of cases where we shift left a 32-bit
value thus might get truncated results on 64-bit
targets.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Suggested-by: Scott Wood <scotttwood@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Emulate TMCFG0 TMRN register exposing one HW thread per vcpu.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[Laurentiu.Tudor@freescale.com: rebased on latest kernel, use
define instead of hardcoded value, moved code in own function]
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Acked-by: Scott Wood <scotttwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The register is not currently used in the base kernel
but will be in a forthcoming kvm patch.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The struct irq_domain contains a "struct device_node *" field
(of_node) that is almost the only link between the irqdomain
and the device tree infrastructure.
In order to prepare for the removal of that field, convert all
users to use irq_domain_get_of_node() instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We need to properly identify whether a hugepage is an explicit or
a transparent hugepage in follow_huge_addr(). We used to depend
on hugepage shift argument to do that. But in some case that can
result in wrong results. For ex:
On finding a transparent hugepage we set hugepage shift to PMD_SHIFT.
But we can end up clearing the thp pte, via pmdp_huge_get_and_clear.
We do prevent reusing the pfn page via the usage of
kick_all_cpus_sync(). But that happens after we updated the pte to 0.
Hence in follow_huge_addr() we can find hugepage shift set, but transparent
huge page check fail for a thp pte.
NOTE: We fixed a variant of this race against thp split in commit
691e95fd73
("powerpc/mm/thp: Make page table walk safe against thp split/collapse")
Without this patch, we may hit the BUG_ON(flags & FOLL_GET) in
follow_page_mask occasionally.
In the long term, we may want to switch ppc64 64k page size config to
enable CONFIG_ARCH_WANT_GENERAL_HUGETLB
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After commit e2b3d202d1
("powerpc: Switch 16GB and 16MB explicit hugepages to a
different page table format"), we don't need to support
is_hugepd() for 64K page size.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All unrecovered machine check errors on PowerNV should cause an
immediate panic. There are 2 reasons that this is the right policy:
it's not safe to continue, and we're already trying to reboot.
Firstly, if we go through the recovery process and do not successfully
recover, we can't be sure about the state of the machine, and it is
not safe to recover and proceed.
Linux knows about the following sources of Machine Check Errors:
- Uncorrectable Errors (UE)
- Effective - Real Address Translation (ERAT)
- Segment Lookaside Buffer (SLB)
- Translation Lookaside Buffer (TLB)
- Unknown/Unrecognised
In the SLB, TLB and ERAT cases, we can further categorise these as
parity errors, multihit errors or unknown/unrecognised.
We can handle SLB errors by flushing and reloading the SLB. We can
handle TLB and ERAT multihit errors by flushing the TLB. (It appears
we may not handle TLB and ERAT parity errors: I will investigate
further and send a followup patch if appropriate.)
This leaves us with uncorrectable errors. Uncorrectable errors are
usually the result of ECC memory detecting an error that it cannot
correct, but they also crop up in the context of PCI cards failing
during DMA writes, and during CAPI error events.
There are several types of UE, and there are 3 places a UE can occur:
Skiboot, the kernel, and userspace. For Skiboot errors, we have the
facility to make some recoverable. For userspace, we can simply kill
(SIGBUS) the affected process. We have no meaningful way to deal with
UEs in kernel space or in unrecoverable sections of Skiboot.
Currently, these unrecovered UEs fall through to
machine_check_expection() in traps.c, which calls die(), which OOPSes
and sends SIGBUS to the process. This sometimes allows us to stumble
onwards. For example we've seen UEs kill the kernel eehd and
khugepaged. However, the process killed could have held a lock, or it
could have been a more important process, etc: we can no longer make
any assertions about the state of the machine. Similarly if we see a
UE in skiboot (and again we've seen this happen), we're not in a
position where we can make any assertions about the state of the
machine.
Likewise, for unknown or unrecognised errors, we're not able to say
anything about the state of the machine.
Therefore, if we have an unrecovered MCE, the most appropriate thing
to do is to panic.
The second reason is that since e784b6499d ("powerpc/powernv: Invoke
opal_cec_reboot2() on unrecoverable machine check errors."), we
attempt a special OPAL reboot on an unhandled MCE. This is so the
hardware can record error data for later debugging.
The comments in that commit assert that we are heading down the panic
path anyway. At the moment this is not always true. With UEs in kernel
space, for instance, they are marked as recoverable by the hardware,
so if the attempt to reboot failed (e.g. old Skiboot), we wouldn't
panic() but would simply die() and OOPS. It doesn't make sense to be
staggering on if we've just tried to reboot: we should panic().
Explicitly panic() on unrecovered MCEs on PowerNV.
Update the comments appropriately.
This fixes some hangs following EEH events on cxlflash setups.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pi_buff is being memset before it is sanity checked. Move the
memset after the null pi_buff sanity check to avoid an oops.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
native_hpte_clear() is called in real mode from two places:
- Early in boot during htab initialisation if firmware assisted dump is
active.
- Late in the kexec path.
In both contexts there is no need to disable interrupts are they are
already disabled. Furthermore, locking around the tlbie() is only required
for pre POWER5 hardware.
On POWER5 or newer hardware concurrent tlbie()s work as expected and on pre
POWER5 hardware concurrent tlbie()s could result in deadlock. This code
would only be executed at crashdump time, during which all bets are off,
concurrent tlbie()s are unlikely and taking locks is unsafe therefore the
best course of action is to simply do nothing. Concurrent tlbie()s are not
possible in the first case as secondary CPUs have not come up yet.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For some reason, only the little-endian flavor of
powerpc provided the zero_bytemask() implementation.
Reported-by: Michal Sojka <sojkam1@fel.cvut.cz>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Enable the "wake-on-filer" (aka. wake on user defined packet)
wake on lan capability for the eTSEC ethernet nodes.
Cc: Li Yang <leoli@freescale.com>
Cc: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arch/tile added word-at-a-time.h after the patch that added generic-y
entries; the generic-y entry is now stale.
arch/h8300 is newer than the generic-y patch for word-at-a-time.h,
and needs a generic-y entry.
arch/powerpc seems to have gotten a generic-y entry by mistake in
the first patch; this change removes it.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Always include a timeout when waiting for secondary cpus to enter OPAL
in the kexec path, rather than only when crashing.
Signed-off-by: Samuel Mendoza-Jonas <sam.mj@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The derive_parent() has similar semantics to what we have in newly introduced
of_helpers module. The replacement reduces code base and propagates the actual
error code to the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In case we have node without '/' strrchr() returns NULL which might lead to
crash. Replace strrchr() by kbasename() and modify condition to avoid such
behaviour.
Suggested-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The helper kstrndup() will do the same in one line.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In case we have a full node name like /foo/bar and /foo is not found the
parent_path left unfreed. So, free a memory before return to a caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Extract a new module to share the code between other modules.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull strscpy string copy function implementation from Chris Metcalf.
Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.
The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.
strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result. To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.
strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string. Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated. It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.
strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG. It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.
So why did I waffle about this for so long?
Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.
And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.
So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches. Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use global strscpy() rather than private copy
string: provide strscpy()
Make asm/word-at-a-time.h available on all architectures
As we need to add further flags to the bpf_prog structure, lets migrate
both bools to a bitfield representation. The size of the base structure
(excluding insns) remains unchanged at 40 bytes.
Add also tags for the kmemchecker, so that it doesn't throw false
positives. Even in case gcc would generate suboptimal code, it's not
being accessed in performance critical paths.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'nvram_create_os_partition' should be 'nvram_create_partition'.
Use __func__ to have it right, as done elsewhere in this file.
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If 'nvram_write_header' fails, then 'new_part' should be freed, otherwise,
there is a memory leak.
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This add helper virt_to_pfn and remove the opencoded usage of the
same.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc has a link register (lr) used for calling functions. We "bl
<func>" to call a function, and "blr" to return back to the call site.
The lr is only a single register, so if we call another function from
inside this function (ie. nested calls), software must save away the
lr on the software stack before calling the new function. Before
returning (ie. before the "blr"), the lr is restored by software from
the software stack.
This makes branch prediction quite difficult for the processor as it
will only know the branch target just before the "blr".
To help with this, modern powerpc processors keep a (non-architected)
hardware stack of lr called a "link stack". When a "bl <func>" is
run, the lr is pushed onto this stack. When a "blr" is called, the
branch predictor pops the lr value from the top of the link stack, and
uses it to predict the branch target. Hence the processor pipeline
knows a lot earlier the branch target.
This works great but there are some cases where you call "bl" but
without a matching "blr". Once such case is when trying to determine
the program counter (which can't be read directly). Here you "bl+4;
mflr" to get the program counter. If you do this, the link stack will
get out of sync with reality, causing the branch predictor to
mis-predict subsequent function returns.
To avoid this, modern micro-architectures have a special case of bl.
Using the form "bcl 20,31,+4", ensures the processor doesn't push to
the link stack.
The 32 and 64 bit variants of __get_datapage() use a "bl; mflr" to
determine the loaded address of the VDSO. The current versions of
these attempt to use this special bl variant.
Unfortunately they use +8 rather than the required +4. Hence the
current code results in the link stack getting out of sync with
reality and hence the resulting performance degradation.
This patch moves it to bcl+4 by moving __kernel_datapage_offset out of
__get_datapage().
With this patch, running a gettimeofday() (which uses
__get_datapage()) microbenchmark we get a decent bump in performance
on POWER7/8.
For the benchmark in tools/testing/selftests/powerpc/benchmarks/gettimeofday.c
POWER8:
64bit gets ~4% improvement
32bit gets ~9% improvement
POWER7:
64bit gets ~7% improvement
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reported-by: Aaron Sawdey <sawdey@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch defines macros for the three bolted SLB indexes we use.
Switch the functions that take the indexes as an argument to use the
enum.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andy Lutomirski says:
Some dynamic loaders may be slightly faster if a GNU hash is
available.
This is unlikely to have any measurable effect on the time it takes
to resolve vdso symbols (since there are so few of them). In some
contexts, it can be a win for a different reason: if every DSO has a
GNU hash section, then libc can avoid calculating SysV hashes at
all. Both musl and glibc appear to have this optimization.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This struct is unused, which is now a build error with gcc 6:
error: 'os_area_db_id_video_mode' defined but not used
There doesn't seem to be any good reason to keep it around so remove it,
it's in the history if anyone needs it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, little endian is only supported on powernv and pseries,
however, Kconfigs still allow us to include other platforms in a LE
kernel, this may result in space wasting or even build error if some
BE-only platforms always assume they are built for a BE kernel. So just
modify the Kconfigs of BE-only platforms to remove them from being built
for a LE kernel.
For 32bit only platforms, nothing needs to be done, because
CPU_LITTLE_ENDIAN depends on PPC64. For 64bit supported platforms, add
CPU_BIG_ENDIAN to dependencies explicitly, so that these platforms will
be disabled for LE [Suggested-by: Cédric Le Goater <clg@fr.ibm.com>].
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 086b91d052 ("scsi_dh: integrate into the core SCSI code")
changed CONFIG_SCSI_DH from tristate to bool.
Our defconfigs have CONFIG_SCSI_DH=m, which the kconfig machinery warns
us is invalid, but instead of converting it to =y it leaves it unset.
This means we loose the CONFIG_SCSI_DH code and everything that depends
on it.
So convert the values in the defconfigs to =y.
Fixes: 086b91d052 ("scsi_dh: integrate into the core SCSI code")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Resource management
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn Helgaas)
MSI
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f4c3
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver:
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
and a few PPC bug fixes too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWBSn7AAoJEL/70l94x66Dxd4H/RT6kWWj9x4grEYUkcJUDyK2
AXm7XcKQm04auwAic8Otr+ts/Qix/50kWmBe/TU0QLgqb8rj5Dj3yGFK6Z1y6mAz
KvaxqMJd4tZGTqN0DDvC2ItEdzjfAdeJZo/FHXqPHVspG0G14T7STLna02LTBBEJ
tNzY9qor8nFhg2fT2szqKaudUNgTqkCTpo57o2BrHE96SHG+m0WdpQCV1F5hPVpg
Te0Pb7qX9xng5n3sQ7IV/t3QYbrza1ACwNQS9XJa0Yu6iEz7JdmVmzHQASK9ynn6
hUHhsNYGx4IsPjPtfJk2GroNaRDZL+VMzw07tfcOvPx8xkS9hS63pwzmSBqfLrM=
=Ywqn
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"AMD fixes for bugs introduced in the 4.2 merge window, and a few PPC
bug fixes too"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: disable halt_poll_ns as default for s390x
KVM: x86: fix off-by-one in reserved bits check
KVM: x86: use correct page table format to check nested page table reserved bits
KVM: svm: do not call kvm_set_cr0 from init_vmcb
KVM: x86: trap AMD MSRs for the TSeg base and mask
KVM: PPC: Book3S: Take the kvm->srcu lock in kvmppc_h_logical_ci_load/store()
KVM: PPC: Book3S HV: Pass the correct trap argument to kvmhv_commence_exit
KVM: PPC: Book3S HV: Fix handling of interrupted VCPUs
kvm: svm: reset mmu on VCPU reset
We observed some performance degradation on s390x with dynamic
halt polling. Until we can provide a proper fix, let's enable
halt_poll_ns as default only for supported architectures.
Architectures are now free to set their own halt_poll_ns
default value.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Access to the kvm->buses (like with the kvm_io_bus_read() and -write()
functions) has to be protected via the kvm->srcu lock.
The kvmppc_h_logical_ci_load() and -store() functions are missing
this lock so far, so let's add it there, too.
This fixes the problem that the kernel reports "suspicious RCU usage"
when lock debugging is enabled.
Cc: stable@vger.kernel.org # v4.1+
Fixes: 99342cf804
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In guest_exit_cont we call kvmhv_commence_exit which expects the trap
number as the argument. However r3 doesn't contain the trap number at
this point and as a result we would be calling the function with a
spurious trap number.
Fix this by copying r12 into r3 before calling kvmhv_commence_exit as
r12 contains the trap number.
Cc: stable@vger.kernel.org # v4.1+
Fixes: eddb60fb14
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a bug which results in stale vcore pointers being left in
the per-cpu preempted vcore lists when a VM is destroyed. The result
of the stale vcore pointers is usually either a crash or a lockup
inside collect_piggybacks() when another VM is run. A typical
lockup message looks like:
[ 472.161074] NMI watchdog: BUG: soft lockup - CPU#24 stuck for 22s! [qemu-system-ppc:7039]
[ 472.161204] Modules linked in: kvm_hv kvm_pr kvm xt_CHECKSUM ipt_MASQUERADE nf_nat_masquerade_ipv4 tun ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw ses enclosure shpchp rtc_opal i2c_opal powernv_rng binfmt_misc dm_service_time scsi_dh_alua radeon i2c_algo_bit drm_kms_helper ttm drm tg3 ptp pps_core cxgb3 ipr i2c_core mdio dm_multipath [last unloaded: kvm_hv]
[ 472.162111] CPU: 24 PID: 7039 Comm: qemu-system-ppc Not tainted 4.2.0-kvm+ #49
[ 472.162187] task: c000001e38512750 ti: c000001e41bfc000 task.ti: c000001e41bfc000
[ 472.162262] NIP: c00000000096b094 LR: c00000000096b08c CTR: c000000000111130
[ 472.162337] REGS: c000001e41bff520 TRAP: 0901 Not tainted (4.2.0-kvm+)
[ 472.162399] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 24848844 XER: 00000000
[ 472.162588] CFAR: c00000000096b0ac SOFTE: 1
GPR00: c000000000111170 c000001e41bff7a0 c00000000127df00 0000000000000001
GPR04: 0000000000000003 0000000000000001 0000000000000000 0000000000874821
GPR08: c000001e41bff8e0 0000000000000001 0000000000000000 d00000000efde740
GPR12: c000000000111130 c00000000fdae400
[ 472.163053] NIP [c00000000096b094] _raw_spin_lock_irqsave+0xa4/0x130
[ 472.163117] LR [c00000000096b08c] _raw_spin_lock_irqsave+0x9c/0x130
[ 472.163179] Call Trace:
[ 472.163206] [c000001e41bff7a0] [c000001e41bff7f0] 0xc000001e41bff7f0 (unreliable)
[ 472.163295] [c000001e41bff7e0] [c000000000111170] __wake_up+0x40/0x90
[ 472.163375] [c000001e41bff830] [d00000000efd6fc0] kvmppc_run_core+0x1240/0x1950 [kvm_hv]
[ 472.163465] [c000001e41bffa30] [d00000000efd8510] kvmppc_vcpu_run_hv+0x5a0/0xd90 [kvm_hv]
[ 472.163559] [c000001e41bffb70] [d00000000e9318a4] kvmppc_vcpu_run+0x44/0x60 [kvm]
[ 472.163653] [c000001e41bffba0] [d00000000e92e674] kvm_arch_vcpu_ioctl_run+0x64/0x170 [kvm]
[ 472.163745] [c000001e41bffbe0] [d00000000e9263a8] kvm_vcpu_ioctl+0x538/0x7b0 [kvm]
[ 472.163834] [c000001e41bffd40] [c0000000002d0f50] do_vfs_ioctl+0x480/0x7c0
[ 472.163910] [c000001e41bffde0] [c0000000002d1364] SyS_ioctl+0xd4/0xf0
[ 472.163986] [c000001e41bffe30] [c000000000009260] system_call+0x38/0xd0
[ 472.164060] Instruction dump:
[ 472.164098] ebc1fff0 ebe1fff8 7c0803a6 4e800020 60000000 60000000 60420000 8bad02e2
[ 472.164224] 7fc3f378 4b6a57c1 60000000 7c210b78 <e92d0000> 89290009 792affe3 40820070
The bug is that kvmppc_run_vcpu does not correctly handle the case
where a vcpu task receives a signal while its guest vcpu is executing
in the guest as a result of being piggy-backed onto the execution of
another vcore. In that case we need to wait for the vcpu to finish
executing inside the guest, and then remove this vcore from the
preempted vcores list. That way, we avoid leaving this vcpu's vcore
on the preempted vcores list when the vcpu gets interrupted.
Fixes: ec25716508
Reported-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJV+/ucAAoJEL/70l94x66DV8YH/1KDym/1GJ+/Br/YkHZnM53l
3Q0PwSLu9cNcIL9lUuDLwGTaVj+y8ud1Hjr/uzvKwivktmUYVZhkdtnZmnanvGOM
qKB9K3nFXCPx8uqy8Dn7fOwEKcg9FmDOTTkWy13HDnXO+V4crSVVt+rPw+6FUMld
NV5tYdw9Lu7y3XrveDebPWaPtyDL7OAagzmeK47eMffxG7X9Hf1H2aT7HueRi7x/
SkLIe3gmiOWmHVJDPE9TOmFYIj19gywDFysKes1gdVJLVUIXiELMT7SrvAYnToVB
zISIEj7Zx4SINPxpf2dUn8REm7NsmJY+PffLIl/Nv+ozGggFQGFH0SMZ08p0bxw=
=tfmn
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Mostly stable material, a lot of ARM fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
sched: access local runqueue directly in single_task_running
arm/arm64: KVM: Remove 'config KVM_ARM_MAX_VCPUS'
arm64: KVM: Remove all traces of the ThumbEE registers
arm: KVM: Disable virtual timer even if the guest is not using it
arm64: KVM: Disable virtual timer even if the guest is not using it
arm/arm64: KVM: vgic: Check for !irqchip_in_kernel() when mapping resources
KVM: s390: Replace incorrect atomic_or with atomic_andnot
arm: KVM: Fix incorrect device to IPA mapping
arm64: KVM: Fix user access for debug registers
KVM: vmx: fix VPID is 0000H in non-root operation
KVM: add halt_attempted_poll to VCPU stats
kvm: fix zero length mmio searching
kvm: fix double free for fast mmio eventfd
kvm: factor out core eventfd assign/deassign logic
kvm: don't try to register to KVM_FAST_MMIO_BUS for non mmio eventfd
KVM: make the declaration of functions within 80 characters
KVM: arm64: add workaround for Cortex-A57 erratum #852523
KVM: fix polling for guest halt continued even if disable it
arm/arm64: KVM: Fix PSCI affinity info return value for non valid cores
arm64: KVM: set {v,}TCR_EL2 RES1 bits
...
Pull irq updates from Thomas Gleixner:
"This is a rather large update post rc1 due to the final steps of
cleanups and API changes which had to wait for the preparatory patches
to hit your tree.
- Regression fixes for ARM GIC irqchips
- Regression fixes and lockdep anotations for renesas irq chips
- The leftovers of the cleanup and preparatory patches which have
been ignored by maintainers
- Final conversions of the newly merged users of obsolete APIs
- Final removal of obsolete APIs
- Final removal of ARM artifacts which had been introduced during the
conversion of ARM to the generic interrupt code.
- Final split of the irq_data into chip specific and common data to
reflect the needs of hierarchical irq domains.
- Treewide removal of the first argument of interrupt flow handlers,
i.e. the irq number, which is not used by the majority of handlers
and simple to retrieve from the other argument the irq descriptor.
- A few comment updates and build warning fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
arm64: Remove ununsed set_irq_flags
ARM: Remove ununsed set_irq_flags
sh: Kill off set_irq_flags usage
irqchip: Kill off set_irq_flags usage
gpu/drm: Kill off set_irq_flags usage
genirq: Remove irq argument from irq flow handlers
genirq: Move field 'msi_desc' from irq_data into irq_common_data
genirq: Move field 'affinity' from irq_data into irq_common_data
genirq: Move field 'handler_data' from irq_data into irq_common_data
genirq: Move field 'node' from irq_data into irq_common_data
irqchip/gic-v3: Use IRQD_FORWARDED_TO_VCPU flag
irqchip/gic: Use IRQD_FORWARDED_TO_VCPU flag
genirq: Provide IRQD_FORWARDED_TO_VCPU status flag
genirq: Simplify irq_data_to_desc()
genirq: Remove __irq_set_handler_locked()
pinctrl/pistachio: Use irq_set_handler_locked
gpio: vf610: Use irq_set_handler_locked
powerpc/mpc8xx: Use irq_set_handler_locked()
powerpc/ipic: Use irq_set_handler_locked()
powerpc/cpm2: Use irq_set_handler_locked()
...
- Fix 32-bit TCE table init in kdump kernel from Nish
- Fix kdump with non-power-of-2 crashkernel= from Nish
- Abort cxl_pci_enable_device_hook() if PCI channel is offline from Andrew
- Fix to release DRC when configure_connector() fails from Bharata
- Wire up sys_userfaultfd()
- Fix race condition in tearing down MSI interrupts from Paul
- Fix unbalanced pci_dev_get() in cxl_probe() from Daniel
- Fix cxl build failure due to -Wunused-variable gcc behaviour change from Ian
- Tell the toolchain to use ABI v2 when building an LE boot wrapper from Benh
- Fix THP to recompute hash value after a failed update from Aneesh
- 32-bit memcpy/memset: only use dcbz once cache is enabled from Christophe
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Dgn5
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix 32-bit TCE table init in kdump kernel from Nish
- Fix kdump with non-power-of-2 crashkernel= from Nish
- Abort cxl_pci_enable_device_hook() if PCI channel is offline from
Andrew
- Fix to release DRC when configure_connector() fails from Bharata
- Wire up sys_userfaultfd()
- Fix race condition in tearing down MSI interrupts from Paul
- Fix unbalanced pci_dev_get() in cxl_probe() from Daniel
- Fix cxl build failure due to -Wunused-variable gcc behaviour change
from Ian
- Tell the toolchain to use ABI v2 when building an LE boot wrapper
from Benh
- Fix THP to recompute hash value after a failed update from Aneesh
- 32-bit memcpy/memset: only use dcbz once cache is enabled from
Christophe
* tag 'powerpc-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc32: memset: only use dcbz once cache is enabled
powerpc32: memcpy: only use dcbz once cache is enabled
powerpc/mm: Recompute hash value after a failed update
powerpc/boot: Specify ABI v2 when building an LE boot wrapper
cxl: Fix build failure due to -Wunused-variable behaviour change
cxl: Fix unbalanced pci_dev_get in cxl_probe
powerpc/MSI: Fix race condition in tearing down MSI interrupts
powerpc: Wire up sys_userfaultfd()
powerpc/pseries: Release DRC when configure_connector fails
cxl: abort cxl_pci_enable_device_hook() if PCI channel is offline
powerpc/powernv/pci-ioda: fix kdump with non-power-of-2 crashkernel=
powerpc/powernv/pci-ioda: fix 32-bit TCE table init in kdump kernel
