To be able to enable SDR12|25 for SD-cards, we needed to fixup the
configuration in DT of the gpio regulator, which handles the signal
voltage level. Some configuration were missing and some were wrong.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove duplicated configurations and move specific details into
each corresponding dtsi file for the href versions.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the few remaining HREFv60 pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Put two extra configs into the device tree to handle the default
configuration of the display reset signals on the HREFv60plus,
move this over from the board file to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the control of muxing and enabling the IPGPIO (image
processor GPIO) from the static set-up to the device tree.
Use a hog as we have no device for the flash controller yet.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves over the configuration of the GPIO keys (used for
proximity sensor and Hall effect sensor) from the static pin
configuration file to the device tree. As part of the exercise,
implement the GPIO keys properly in a per-UIB file as this
setup actually differs with each UIB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The BU21013 touchscreen GPIOs have been pretty confused, correct
them per board, and move the GPIO assignments up to the top
level DTS file so we can control it from there, and avoid defining
the GPIO assignments for non-ST UIB equipped boards.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the device tree conversion did away with the ability to
auto-detect the UIB (User Interface Board) version from attempting
to read an I2C address, we now have to pass the knowledge of
what UIB is mounted through the device tree. This gives rise
to four possible board permutations:
- HREF prior to v60, ST UIB (hrefprev60-stuib)
- HREF prior to v60, TVK1281618 UIB (hrefprev60-tvk)
- HREF v60 and later, ST UIB (href60plus-stuib)
- HREF v60 and later, TVK1281618 UIB (hrefv60plus-tvk)
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-10-02 16:17:04 +02:00
Renamed from arch/arm/boot/dts/ste-hrefv60plus.dts (Browse further)
