Happened when the Playback (or Capture) is running continuously
and Capture (or Playback) is restarted (xrun, manual stop/start...)
Since the RX (or TX) FIFO are only reset when the whole SSI is disabled,
pending samples from previous capture (or playback) session may still
be present. They must be erased to not introduce channel slipping.
FIFO Clear register fields are documented in IMX51, IMX35 reference manual.
They are not documented in IMX50 or IMX6 RM, despite they are
working as expected on IMX6SL and IMX6solo.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, SCR.SSIEN and SCR.TE were enabled at once if no capture
stream was also running.
This may not give a chance for the DMA to write the first sample in
TX FIFO before the streaming starts on the PCM bus, inserting void
samples first.
Those void samples are then responsible for slipping the channels.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the capture is already running while playback is started, it is highly
probable (>80% in a 8 channels scenario) that samples are lost between
the DMA and TX fifo.
The reason is that SIER.TDMAE is set before STCR.TFEN0, leaving a time
window where the FIFO doesn't receive the samples written by the DMA.
This particular case happened only if capture is already enabled as
SCR.SSIEN is already set at the playback startup instant.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of functions only receive the ssi_private reference and don't have
a knowledge of 'dev' pointer, even for debug purpose.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
im6sl reference manual 47.7.4:
"
Bit clock - Used to serially clock the data bits in and out of the SSI port.
This clock is either generated internally (from SSI's sys clock) or taken
from external clock source (through the Tx/Rx clock ports).
[...]
Care should be taken to ensure that the bit clock frequency (either
internally generated by dividing the SSI's sys clock or sourced from
external device through Tx/Rx clock ports) is never greater than 1/5
of the ipg_clk (from CCM) frequency.
"
Since, in master mode, the sysclk is a multiple of bitclk, we can
easily reach a high sysclk value, whereas keeping a reasonable bitclk.
ex: 8ch x 16bit x 48kHz = 6144000, requires a 24576000 sysclk (PM=1)
yet ipg_clk/5 = 66Mhz/5 = 13.2
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max number of slots in TDM mode is 32:
- Frame Rate Divider Control is a 5bit value
- Time slot mask registers control 32 slots.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TLV320AIC32x4 has a very flexible mixer on the inputs to the ADCs. Each
mixer has an available set of available pins that can be connected to the
ADC positive and negative pins via three different resistor values. This
allows for configuration of differential inputs as well as doing level
manipulation between sources going into the mixers.
The current code only provides positive pins and I implemented the resistors
in an earlier patch. It turns out that it appears to more accurately model
what's happening to implement each of the pins as a MUX rather than on/off
switches and a mixer. This way each pin can be set to its desired resistor
value. Since there are no switches, the mixer is no longer necessary in the
DAPM path. I set the DAPM paths such that the "off" position of any of the
MUXes turns the path off.
This should allow for any input confiuration available on the codec.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some definitions to support the PCM5102A codec
by Texas Instruments.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Changes to original patch by Florian Meier:
* rebased (Makefile and Kconfig
* fixed checkpath errors (spaces, newlines)
* added dt-binding documentation
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Manage the hda idisp link using shiny new link APIs. We need to
keep link On while we probe and also hold the reference in runtime
resume and drop in suspend
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use shiny new link APIs to manage the links. Also remove old link
configuration logic from driver.
We need to keep link and cmd dma to off during active suspend
to allow system to enter low power state and turn it on if
the link and cmd dma was on before active suspend in active
resume.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The HDA links can be switched off when not is use, similarly
command DMA can be stopped as well. This calls for a reference
counting mechanism on the link by it's users to manage the link
power. The DMA can be turned off when all links are off
For this we add two APIs
snd_hdac_ext_bus_link_get
snd_hdac_ext_bus_link_put
They help users to turn up/down link and manage the DMA as well
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Patch 562abd39 "xen-netback: support multiple extra info fragments
passed from frontend" contained a mistake which can result in an in-
correct number of responses being generated when handling errors
encountered when processing packets containing extra info fragments.
This patch fixes the problem.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reported-by: Jan Beulich <JBeulich@suse.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User visible:
- Fallback to usermode only counters when perf_event_paranoid > 1, which
is the case now (Arnaldo Carvalho de Melo)
- Do not reassign parg after collapse_tree() in libtraceevent, which
may cause tool crashes (Steven Rostedt)
Build fixes:
- Fix the build on Fedora Rawhide, where readdir_r() is deprecated and
also wrt -Werror=unused-const-variable= + x86_32_regoffset_table on
!x86_64 (Arnaldo Carvalho de Melo)
- Fix the build on Ubuntu 12.04.5, where dwarf_getlocations() isn't
available, i.e. libdw-dev < 0.157 (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qn4a
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-20160512' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fallback to usermode-only counters when perf_event_paranoid > 1, which
is the case now (Arnaldo Carvalho de Melo)
- Do not reassign parg after collapse_tree() in libtraceevent, which
may cause tool crashes (Steven Rostedt)
- Fix the build on Fedora Rawhide, where readdir_r() is deprecated and
also wrt -Werror=unused-const-variable= + x86_32_regoffset_table on
!x86_64 (Arnaldo Carvalho de Melo)
- Fix the build on Ubuntu 12.04.5, where dwarf_getlocations() isn't
available, i.e. libdw-dev < 0.157 (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge fixes from Andrew Morton:
"4 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: thp: calculate the mapcount correctly for THP pages during WP faults
ksm: fix conflict between mmput and scan_get_next_rmap_item
ocfs2: fix posix_acl_create deadlock
ocfs2: revert using ocfs2_acl_chmod to avoid inode cluster lock hang
This will provide fully accuracy to the mapcount calculation in the
write protect faults, so page pinning will not get broken by false
positive copy-on-writes.
total_mapcount() isn't the right calculation needed in
reuse_swap_page(), so this introduces a page_trans_huge_mapcount()
that is effectively the full accurate return value for page_mapcount()
if dealing with Transparent Hugepages, however we only use the
page_trans_huge_mapcount() during COW faults where it strictly needed,
due to its higher runtime cost.
This also provide at practical zero cost the total_mapcount
information which is needed to know if we can still relocate the page
anon_vma to the local vma. If page_trans_huge_mapcount() returns 1 we
can reuse the page no matter if it's a pte or a pmd_trans_huge
triggering the fault, but we can only relocate the page anon_vma to
the local vma->anon_vma if we're sure it's only this "vma" mapping the
whole THP physical range.
Kirill A. Shutemov discovered the problem with moving the page
anon_vma to the local vma->anon_vma in a previous version of this
patch and another problem in the way page_move_anon_rmap() was called.
Andrew Morton discovered that CONFIG_SWAP=n wouldn't build in a
previous version, because reuse_swap_page must be a macro to call
page_trans_huge_mapcount from swap.h, so this uses a macro again
instead of an inline function. With this change at least it's a less
dangerous usage than it was before, because "page" is used only once
now, while with the previous code reuse_swap_page(page++) would have
called page_mapcount on page+1 and it would have increased page twice
instead of just once.
Dean Luick noticed an uninitialized variable that could result in a
rmap inefficiency for the non-THP case in a previous version.
Mike Marciniszyn said:
: Our RDMA tests are seeing an issue with memory locking that bisects to
: commit 61f5d698cc ("mm: re-enable THP")
:
: The test program registers two rather large MRs (512M) and RDMA
: writes data to a passive peer using the first and RDMA reads it back
: into the second MR and compares that data. The sizes are chosen randomly
: between 0 and 1024 bytes.
:
: The test will get through a few (<= 4 iterations) and then gets a
: compare error.
:
: Tracing indicates the kernel logical addresses associated with the individual
: pages at registration ARE correct , the data in the "RDMA read response only"
: packets ARE correct.
:
: The "corruption" occurs when the packet crosse two pages that are not physically
: contiguous. The second page reads back as zero in the program.
:
: It looks like the user VA at the point of the compare error no longer points to
: the same physical address as was registered.
:
: This patch totally resolves the issue!
Link: http://lkml.kernel.org/r/1462547040-1737-2-git-send-email-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: "Kirill A. Shutemov" <kirill@shutemov.name>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Tested-by: Josh Collier <josh.d.collier@intel.com>
Cc: Marc Haber <mh+linux-kernel@zugschlus.de>
Cc: <stable@vger.kernel.org> [4.5]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A concurrency issue about KSM in the function scan_get_next_rmap_item.
task A (ksmd): |task B (the mm's task):
|
mm = slot->mm; |
down_read(&mm->mmap_sem); |
|
... |
|
spin_lock(&ksm_mmlist_lock); |
|
ksm_scan.mm_slot go to the next slot; |
|
spin_unlock(&ksm_mmlist_lock); |
|mmput() ->
| ksm_exit():
|
|spin_lock(&ksm_mmlist_lock);
|if (mm_slot && ksm_scan.mm_slot != mm_slot) {
| if (!mm_slot->rmap_list) {
| easy_to_free = 1;
| ...
|
|if (easy_to_free) {
| mmdrop(mm);
| ...
|
|So this mm_struct may be freed in the mmput().
|
up_read(&mm->mmap_sem); |
As we can see above, the ksmd thread may access a mm_struct that already
been freed to the kmem_cache. Suppose a fork will get this mm_struct from
the kmem_cache, the ksmd thread then call up_read(&mm->mmap_sem), will
cause mmap_sem.count to become -1.
As suggested by Andrea Arcangeli, unmerge_and_remove_all_rmap_items has
the same SMP race condition, so fix it too. My prev fix in function
scan_get_next_rmap_item will introduce a different SMP race condition, so
just invert the up_read/spin_unlock order as Andrea Arcangeli said.
Link: http://lkml.kernel.org/r/1462708815-31301-1-git-send-email-zhouchengming1@huawei.com
Signed-off-by: Zhou Chengming <zhouchengming1@huawei.com>
Suggested-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Geliang Tang <geliangtang@163.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Ding Tianhong <dingtianhong@huawei.com>
Cc: Li Bin <huawei.libin@huawei.com>
Cc: Zhen Lei <thunder.leizhen@huawei.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 702e5bc68a ("ocfs2: use generic posix ACL infrastructure")
refactored code to use posix_acl_create. The problem with this function
is that it is not mindful of the cluster wide inode lock making it
unsuitable for use with ocfs2 inode creation with ACLs. For example,
when used in ocfs2_mknod, this function can cause deadlock as follows.
The parent dir inode lock is taken when calling posix_acl_create ->
get_acl -> ocfs2_iop_get_acl which takes the inode lock again. This can
cause deadlock if there is a blocked remote lock request waiting for the
lock to be downconverted. And same deadlock happened in ocfs2_reflink.
This fix is to revert back using ocfs2_init_acl.
Fixes: 702e5bc68a ("ocfs2: use generic posix ACL infrastructure")
Signed-off-by: Tariq Saeed <tariq.x.saeed@oracle.com>
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 743b5f1434 ("ocfs2: take inode lock in ocfs2_iop_set/get_acl()")
introduced this issue. ocfs2_setattr called by chmod command holds
cluster wide inode lock when calling posix_acl_chmod. This latter
function in turn calls ocfs2_iop_get_acl and ocfs2_iop_set_acl. These
two are also called directly from vfs layer for getfacl/setfacl commands
and therefore acquire the cluster wide inode lock. If a remote
conversion request comes after the first inode lock in ocfs2_setattr,
OCFS2_LOCK_BLOCKED will be set. And this will cause the second call to
inode lock from the ocfs2_iop_get_acl() to block indefinetly.
The deleted version of ocfs2_acl_chmod() calls __posix_acl_chmod() which
does not call back into the filesystem. Therefore, we restore
ocfs2_acl_chmod(), modify it slightly for locking as needed, and use that
instead.
Fixes: 743b5f1434 ("ocfs2: take inode lock in ocfs2_iop_set/get_acl()")
Signed-off-by: Tariq Saeed <tariq.x.saeed@oracle.com>
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I tried to fix this before, but my previous fix was incomplete
and we can still get the same link error in randconfig builds
because of the way that Kconfig treats the
default y if MVNETA=y && MVNETA_BM_ENABLE
line that does not actually trigger when MVNETA_BM_ENABLE=m,
unlike I intended.
Changing the line to use MVNETA_BM_ENABLE!=n however has
the desired effect and hopefully makes all configurations
work as expected.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 019ded3aa7 ("net: mvneta: bm: clarify dependencies")
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a pretty boring pull request as you wish: including a few
small and trivial HD-audio and USB-audio quirks and a couple of small
regression fixes in HD-audio.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lhNO
-----END PGP SIGNATURE-----
Merge tag 'sound-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This is a pretty boring pull request as you wish: including a few
small and trivial HD-audio and USB-audio quirks and a couple of small
regression fixes in HD-audio"
* tag 'sound-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Yet another Phoneix Audio device quirk
ALSA: hda - Fix regression on ATI HDMI audio
ALSA: hda - Fix subwoofer pin on ASUS N751 and N551
ALSA: hda - Fix broken reconfig
ALSA: hda - Fix white noise on Asus UX501VW headset
ALSA: usb-audio: Quirk for yet another Phoenix Audio devices (v2)
After 0161028b7c ("perf/core: Change the default paranoia level to 2")
'perf stat' fails for users without CAP_SYS_ADMIN, so just use
'perf_evsel__fallback()' to have the same behaviour as 'perf record',
i.e. set perf_event_attr.exclude_kernel to 1.
Now:
[acme@jouet linux]$ perf stat usleep 1
Performance counter stats for 'usleep 1':
0.352536 task-clock:u (msec) # 0.423 CPUs utilized
0 context-switches:u # 0.000 K/sec
0 cpu-migrations:u # 0.000 K/sec
49 page-faults:u # 0.139 M/sec
309,407 cycles:u # 0.878 GHz
243,791 instructions:u # 0.79 insn per cycle
49,622 branches:u # 140.757 M/sec
3,884 branch-misses:u # 7.83% of all branches
0.000834174 seconds time elapsed
[acme@jouet linux]$
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-b20jmx4dxt5hpaa9t2rroi0o@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Now with the default for the kernel.perf_event_paranoid sysctl being 2 [1]
we need to fall back to :u, i.e. to set perf_event_attr.exclude_kernel
to 1.
Before:
[acme@jouet linux]$ perf record usleep 1
Error:
You may not have permission to collect stats.
Consider tweaking /proc/sys/kernel/perf_event_paranoid,
which controls use of the performance events system by
unprivileged users (without CAP_SYS_ADMIN).
The current value is 2:
-1: Allow use of (almost) all events by all users
>= 0: Disallow raw tracepoint access by users without CAP_IOC_LOCK
>= 1: Disallow CPU event access by users without CAP_SYS_ADMIN
>= 2: Disallow kernel profiling by users without CAP_SYS_ADMIN
[acme@jouet linux]$
After:
[acme@jouet linux]$ perf record usleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.016 MB perf.data (7 samples) ]
[acme@jouet linux]$ perf evlist
cycles:u
[acme@jouet linux]$ perf evlist -v
cycles:u: size: 112, { sample_period, sample_freq }: 4000, sample_type: IP|TID|TIME|PERIOD, disabled: 1, inherit: 1, exclude_kernel: 1, mmap: 1, comm: 1, freq: 1, enable_on_exec: 1, task: 1, sample_id_all: 1, exclude_guest: 1, mmap2: 1, comm_exec: 1
[acme@jouet linux]$
And if the user turns on verbose mode, an explanation will appear:
[acme@jouet linux]$ perf record -v usleep 1
Warning:
kernel.perf_event_paranoid=2, trying to fall back to excluding kernel samples
mmap size 528384B
[ perf record: Woken up 1 times to write data ]
Looking at the vmlinux_path (8 entries long)
Using /lib/modules/4.6.0-rc7+/build/vmlinux for symbols
[ perf record: Captured and wrote 0.016 MB perf.data (7 samples) ]
[acme@jouet linux]$
[1] 0161028b7c ("perf/core: Change the default paranoia level to 2")
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-b20jmx4dxt5hpaa9t2rroi0o@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Switch the order of the loops to walk the rates on the top
so we exhaust all DP 1.1 rate/lane combinations before trying
DP 1.2 rate/lane combos.
This avoids selecting rates that are supported by the monitor,
but not the connector leading to valid modes getting rejected.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=95206
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Switch the order of the loops to walk the rates on the top
so we exhaust all DP 1.1 rate/lane combinations before trying
DP 1.2 rate/lane combos.
This avoids selecting rates that are supported by the monitor,
but not the connector leading to valid modes getting rejected.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=95206
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We were showing a hardcoded default value for the kernel.perf_event_paranoid
sysctl, now that it became more paranoid (1 -> 2 [1]), this would need to be
updated, instead show the current value:
[acme@jouet linux]$ perf record ls
Error:
You may not have permission to collect stats.
Consider tweaking /proc/sys/kernel/perf_event_paranoid,
which controls use of the performance events system by
unprivileged users (without CAP_SYS_ADMIN).
The current value is 2:
-1: Allow use of (almost) all events by all users
>= 0: Disallow raw tracepoint access by users without CAP_IOC_LOCK
>= 1: Disallow CPU event access by users without CAP_SYS_ADMIN
>= 2: Disallow kernel profiling by users without CAP_SYS_ADMIN
[acme@jouet linux]$
[1] 0161028b7c ("perf/core: Change the default paranoia level to 2")
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-0gc4rdpg8d025r5not8s8028@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
- The pull up/down logic for the AT91 PIO4 controller was tilted:
we need to mask the reverse pull when unmasking a pull direction.
Setting both pull up & pull down is illegal and makes no sense.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Kzzn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fix from Linus Walleij:
"A single last pin control fix for v4.6. t's tagged for stable and
only hits a single driver with two added lines so should be safe.
Tested in linux-next.
- The pull up/down logic for the AT91 PIO4 controller was tilted: we
need to mask the reverse pull when unmasking a pull direction.
Setting both pull up & pull down is illegal and makes no sense"
* tag 'pinctrl-v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: at91-pio4: fix pull-up/down logic
------------[ cut here ]------------
WARNING: CPU: 0 PID: 16 at kernel/workqueue.c:4559 rebind_workers+0x1c0/0x1d0
Modules linked in:
CPU: 0 PID: 16 Comm: cpuhp/0 Not tainted 4.6.0-rc4+ #31
Hardware name: IBM IBM System x3550 M4 Server -[7914IUW]-/00Y8603, BIOS -[D7E128FUS-1.40]- 07/23/2013
0000000000000000 ffff881037babb58 ffffffff8139d885 0000000000000010
0000000000000000 0000000000000000 0000000000000000 ffff881037babba8
ffffffff8108505d ffff881037ba0000 000011cf3e7d6e60 0000000000000046
Call Trace:
dump_stack+0x89/0xd4
__warn+0xfd/0x120
warn_slowpath_null+0x1d/0x20
rebind_workers+0x1c0/0x1d0
workqueue_cpu_up_callback+0xf5/0x1d0
notifier_call_chain+0x64/0x90
? trace_hardirqs_on_caller+0xf2/0x220
? notify_prepare+0x80/0x80
__raw_notifier_call_chain+0xe/0x10
__cpu_notify+0x35/0x50
notify_down_prepare+0x5e/0x80
? notify_prepare+0x80/0x80
cpuhp_invoke_callback+0x73/0x330
? __schedule+0x33e/0x8a0
cpuhp_down_callbacks+0x51/0xc0
cpuhp_thread_fun+0xc1/0xf0
smpboot_thread_fn+0x159/0x2a0
? smpboot_create_threads+0x80/0x80
kthread+0xef/0x110
? wait_for_completion+0xf0/0x120
? schedule_tail+0x35/0xf0
ret_from_fork+0x22/0x50
? __init_kthread_worker+0x70/0x70
---[ end trace eb12ae47d2382d8f ]---
notify_down_prepare: attempt to take down CPU 0 failed
This bug can be reproduced by below config w/ nohz_full= all cpus:
CONFIG_BOOTPARAM_HOTPLUG_CPU0=y
CONFIG_DEBUG_HOTPLUG_CPU0=y
CONFIG_NO_HZ_FULL=y
As Thomas pointed out:
| If a down prepare callback fails, then DOWN_FAILED is invoked for all
| callbacks which have successfully executed DOWN_PREPARE.
|
| But, workqueue has actually two notifiers. One which handles
| UP/DOWN_FAILED/ONLINE and one which handles DOWN_PREPARE.
|
| Now look at the priorities of those callbacks:
|
| CPU_PRI_WORKQUEUE_UP = 5
| CPU_PRI_WORKQUEUE_DOWN = -5
|
| So the call order on DOWN_PREPARE is:
|
| CB 1
| CB ...
| CB workqueue_up() -> Ignores DOWN_PREPARE
| CB ...
| CB X ---> Fails
|
| So we call up to CB X with DOWN_FAILED
|
| CB 1
| CB ...
| CB workqueue_up() -> Handles DOWN_FAILED
| CB ...
| CB X-1
|
| So the problem is that the workqueue stuff handles DOWN_FAILED in the up
| callback, while it should do it in the down callback. Which is not a good idea
| either because it wants to be called early on rollback...
|
| Brilliant stuff, isn't it? The hotplug rework will solve this problem because
| the callbacks become symetric, but for the existing mess, we need some
| workaround in the workqueue code.
The boot CPU handles housekeeping duty(unbound timers, workqueues,
timekeeping, ...) on behalf of full dynticks CPUs. It must remain
online when nohz full is enabled. There is a priority set to every
notifier_blocks:
workqueue_cpu_up > tick_nohz_cpu_down > workqueue_cpu_down
So tick_nohz_cpu_down callback failed when down prepare cpu 0, and
notifier_blocks behind tick_nohz_cpu_down will not be called any
more, which leads to workers are actually not unbound. Then hotplug
state machine will fallback to undo and online cpu 0 again. Workers
will be rebound unconditionally even if they are not unbound and
trigger the warning in this progress.
This patch fix it by catching !DISASSOCIATED to avoid rebind bound
workers.
Cc: Tejun Heo <tj@kernel.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: stable@vger.kernel.org
Suggested-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
- fix a regression on the clock subsystem while switching to syscon/regmap
due to a stricter check of the register map.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXM0NyAAoJEAf03oE53VmQ0IwIAI05Acjbko78+Hm/kWHlbJrx
5BLpJqTGLavbjbPjFnElKTr1c8m7Bgd6HNcat/2z9ZNh8/82FXyGOjYSp4W0BE9V
ovyD/lz/2fZyom4YLJjdCnVkwIV1pKHS+uNxy5zXMY2gJfz4VRtUh54H3ArdaQOE
LOKvrVl9bGorLbzbTpH0rSeKqQ1XFGPDlp1A3GUtI6646RWd5Eqe6zDzgQUwWJis
AR+sAcsqVb+IWY5rZwMyL0oZ1kjnEw4tihDTy+G+eBXRdRMYqSgEt8dBz65T3VYi
5EFXLuLjknnf3qVaxEU+og6kiJkefTYdB4I7xVR+dKbcILBSSqdHxlG1HmNkBQ4=
=CF/9
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "Second AT91 fix PR for 4.6" from Nicolas Ferre:
- fix a regression on the clock subsystem while switching to syscon/regmap
due to a stricter check of the register map.
* tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sam9x5: Fix the memory range assigned to the PMC
commit 4f41fc5962 ("cgroup, kernfs: make mountinfo
show properly scoped path for cgroup namespaces")
added the following compile warning:
kernel/cgroup.c: In function ‘cgroup_show_path’:
kernel/cgroup.c:1634:15: warning: unused variable ‘ret’ [-Wunused-variable]
int len = 0, ret = 0;
^
fix it.
Fixes: 4f41fc5962 ("cgroup, kernfs: make mountinfo show properly scoped path for cgroup namespaces")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Our caller expects 0 on success, not >0.
This fixes a bug in the patch
cgroup, kernfs: make mountinfo show properly scoped path for cgroup namespaces
where /sys does not show up in mountinfo, breaking criu.
Thanks for catching this, Andrei.
Reported-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Serge Hallyn <serge.hallyn@ubuntu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The current device tree representation of the R-Car Sample Rate Converters
(SRC) assumes that they are numbered consecutively, starting from 0. Alas,
this is not the case with the R8A7794 SoC where SRC0 isn't present. In
order to keep the existing device trees working, I'm suggesting to use a
disabled node for SRC0. Teach the SRC probe to just skip disabled nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
At the end of process_filter(), collapse_tree() was changed to update
the parg parameter, but the reassignment after the call wasn't removed.
What happens is that the "current_op" gets modified and freed and parg
is assigned to the new allocated argument. But after the call to
collapse_tree(), parg is assigned again to the just freed "current_op",
and this causes the tool to crash.
The current_op variable must also be assigned to NULL in case of error,
otherwise it will cause it to be free()ed twice.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org # 3.14+
Fixes: 42d6194d13 ("tools lib traceevent: Refactor process_filter()")
Link: http://lkml.kernel.org/r/20160511150936.678c18a1@gandalf.local.home
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
If not, tell the user that:
config/Makefile:273: Old libdw.h, finding variables at given 'perf probe' point will not work, install elfutils-devel/libdw-dev >= 0.157
And return -ENOTSUPP in die_get_var_range(), failing features that
need it, like the one pointed out above.
This fixes the build on older systems, such as Ubuntu 12.04.5.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Vinson Lee <vlee@freedesktop.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-9l7luqkq4gfnx7vrklkq4obs@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To fix the build on Fedora Rawhide (gcc 6.0.0 20160311 (Red Hat 6.0.0-0.17):
CC /tmp/build/perf/arch/x86/util/dwarf-regs.o
arch/x86/util/dwarf-regs.c:66:36: error: 'x86_32_regoffset_table' defined but not used [-Werror=unused-const-variable=]
static const struct pt_regs_offset x86_32_regoffset_table[] = {
^~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-fghuksc1u8ln82bof4lwcj0o@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The readdir() function is thread safe as long as just one thread uses a
DIR, which is the case when parsing tracepoint event definitions, to
avoid breaking the build with glibc-2.23.90 (upcoming 2.24), use it
instead of readdir_r().
See: http://man7.org/linux/man-pages/man3/readdir.3.html
"However, in modern implementations (including the glibc implementation),
concurrent calls to readdir() that specify different directory streams
are thread-safe. In cases where multiple threads must read from the
same directory stream, using readdir() with external synchronization is
still preferable to the use of the deprecated readdir_r(3) function."
Noticed while building on a Fedora Rawhide docker container.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-wddn49r6bz6wq4ee3dxbl7lo@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The readdir() function is thread safe as long as just one thread uses a
DIR, which is the case in thread_map, so, to avoid breaking the build
with glibc-2.23.90 (upcoming 2.24), use it instead of readdir_r().
See: http://man7.org/linux/man-pages/man3/readdir.3.html
"However, in modern implementations (including the glibc implementation),
concurrent calls to readdir() that specify different directory streams
are thread-safe. In cases where multiple threads must read from the
same directory stream, using readdir() with external synchronization is
still preferable to the use of the deprecated readdir_r(3) function."
Noticed while building on a Fedora Rawhide docker container.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-del8h2a0f40z75j4r42l96l0@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The readdir() function is thread safe as long as just one thread uses a
DIR, which is the case in 'perf script', so, to avoid breaking the build
with glibc-2.23.90 (upcoming 2.24), use it instead of readdir_r().
See: http://man7.org/linux/man-pages/man3/readdir.3.html
"However, in modern implementations (including the glibc implementation),
concurrent calls to readdir() that specify different directory streams
are thread-safe. In cases where multiple threads must read from the
same directory stream, using readdir() with external synchronization is
still preferable to the use of the deprecated readdir_r(3) function."
Noticed while building on a Fedora Rawhide docker container.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-mt3xz7n2hl49ni2vx7kuq74g@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Broxton-P reference platform also uses combo jack for audio
connector so we need to set codec pdata to use this based on DMI
match for this board.
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACPI driver data can be NULL so we need to check that before
dereference the driver data.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
