A clock branch consisting of a mux and divider with non-standard
divider values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The macros calculate the correct offset from the id in the parameter.
If this parameter does not consist of a single number, the calculation
will return wrong registers in the best case or create unaligned accesses
in the worst case. So protect the calculations against such values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The video input processor (vip) was called camera interface (cif) on
older socs which seems to have resulted in a copy'n'paste error when
creating the rk3288 camera clocks.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The dwmac ethernet controller on the rk3288 supports phys connected
via rgmii and rmii. With rgmii phys it is expected that the mac clock
is provided externally while with rmii phys the clock can be external
but also generated from the plls. In the later case it of course needs
be at 50MHz, which gets set from the dwmac_rk driver.
As most devices use a rgmii phy it never surfaced so far that the mac
clk mux, doesn't go up one lever to the pll clock in the rmii case with
internal clock generation, as it is missing the CLK_SET_RATE_PARENT flag,
and thus will not set the correct frequency in most cases.
Fixes: b9e4ba5416 ("clk: rockchip: add clock controller for rk3288")
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch fixes the mux bit-setting for ClockgenA9.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Fixes: 13e6f2da1d ("clk: st: STiH407: Support for A9 MUX Clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the CLK_GET_RATE_NOCACHE flag to all the clocks with recalc ops,
so that they reflect Hw rate after CPS wake-up when a clk_get_rate()
is called
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
While proving lock, the following warning happens
and it is fixed after initializing lock in the setup
function
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.27-02861-g39df285-dirty #33
[<c00154ac>] (unwind_backtrace+0x0/0xf4) from [<c0011b50>] (show_stack+0x10/0x14)
[<c0011b50>] (show_stack+0x10/0x14) from [<c00689ac>] (__lock_acquire+0x900/0xb14)
[<c00689ac>] (__lock_acquire+0x900/0xb14) from [<c0069394>] (lock_acquire+0x68/0x7c)
[<c0069394>] (lock_acquire+0x68/0x7c) from [<c04958f8>] (_raw_spin_lock_irqsave+0x48/0x5c)
[<c04958f8>] (_raw_spin_lock_irqsave+0x48/0x5c) from [<c0381e6c>] (clk_gate_endisable+0x28/0x88)
[<c0381e6c>] (clk_gate_endisable+0x28/0x88) from [<c0381ee0>] (clk_gate_enable+0xc/0x14)
[<c0381ee0>] (clk_gate_enable+0xc/0x14) from [<c0386c68>] (flexgen_enable+0x28/0x40)
[<c0386c68>] (flexgen_enable+0x28/0x40) from [<c037f260>] (__clk_enable+0x5c/0x9c)
[<c037f260>] (__clk_enable+0x5c/0x9c) from [<c037f558>] (clk_enable+0x18/0x2c)
[<c037f558>] (clk_enable+0x18/0x2c) from [<c064a1dc>] (st_lpc_of_register+0xc0/0x248)
[<c064a1dc>] (st_lpc_of_register+0xc0/0x248) from [<c0649e44>] (clocksource_of_init+0x34/0x58)
[<c0649e44>] (clocksource_of_init+0x34/0x58) from [<c0637ddc>] (sti_timer_init+0x10/0x18)
[<c0637ddc>] (sti_timer_init+0x10/0x18) from [<c06343f8>] (time_init+0x20/0x30)
[<c06343f8>] (time_init+0x20/0x30) from [<c0632984>] (start_kernel+0x20c/0x2e8)
[<c0632984>] (start_kernel+0x20c/0x2e8) from [<40008074>] (0x40008074)
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Fixes: b116517055 ("clk: st: STiH407: Support for Flexgen Clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch fixes the value for disabling the FSYN channel clock.
The 'is_enabled' returned value is also fixed.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove this duplicated code due to a bad copy / paste.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since the parent rate has been recalculated, pixel RCG clock
should rely on it to find the correct M/N values during set_rate,
instead of calling __clk_round_rate() to its parent again.
Signed-off-by: Hai Li <hali@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Fixes: 99cbd064b0 ("clk: qcom: Support display RCG clocks")
[sboyd@codeaurora.org: Silenced unused parent variable warning]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add machine support for the Allwinner A33 quad core cortex-a7 based SoC,
which is similar to the A23 SoC.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WLBw
-----END PGP SIGNATURE-----
Merge tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_platform_driver replacement from Paul Gortmaker:
"Replace module_platform_driver with builtin_platform driver in non
modules.
We see an increasing number of non-modular drivers using
modular_driver() type register functions. There are several downsides
to letting this continue unchecked:
- The code can appear modular to a reader of the code, and they won't
know if the code really is modular without checking the Makefile
and Kconfig to see if compilation is governed by a bool or
tristate.
- Coders of drivers may be tempted to code up an __exit function that
is never used, just in order to satisfy the required three args of
the modular registration function.
- Non-modular code ends up including the <module.h> which increases
CPP overhead that they don't need.
- It hinders us from performing better separation of the module init
code and the generic init code.
So here we introduce similar macros for builtin drivers. Then we
convert builtin drivers (controlled by a bool Kconfig) by making the
following type of mapping:
module_platform_driver() ---> builtin_platform_driver()
module_platform_driver_probe() ---> builtin_platform_driver_probe().
The set of drivers that are converted here are just the ones that
showed up as relying on an implicit include of <module.h> during a
pending header cleanup. So we convert them here vs adding an include
of <module.h> to non-modular code to avoid compile fails. Additonal
conversions can be done asynchronously at any time.
Once again, an unused module_exit function that is removed here
appears in the diffstat as an outlier wrt all the other changes"
* tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver
drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver
drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver
drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver
drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver
drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver
platform_device: better support builtin boilerplate avoidance
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0BDx
-----END PGP SIGNATURE-----
Merge tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part one from Paul Gortmaker:
"Replace module_init with equivalent device_initcall in non modules.
This series of commits converts non-modular code that is using the
module_init() call to hook itself into the system to instead use
device_initcall().
The conversion is a runtime no-op, since module_init actually becomes
__initcall in the non-modular case, and that in turn gets mapped onto
device_initcall. A couple files show a larger negative diffstat,
representing ones that had a module_exit function that we remove here
vs previously relying on the linker to dispose of it.
We make this conversion now, so that we can relocate module_init from
init.h into module.h in the future.
The files changed here are just limited to those that would otherwise
have to add module.h to obviously non-modular code, in order to avoid
a compile fail, as testing has shown"
* tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MIPS: don't use module_init in non-modular cobalt/mtd.c file
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
cris: don't use module_init for non-modular core eeprom.c code
tty/metag_da: Avoid module_init/module_exit in non-modular code
drivers/clk: don't use module_init in clk-nomadik.c which is non-modular
xtensa: don't use module_init for non-modular core network.c code
sh: don't use module_init in non-modular psw.c code
mn10300: don't use module_init in non-modular flash.c code
parisc64: don't use module_init for non-modular core perf code
parisc: don't use module_init for non-modular core pdc_cons code
cris: don't use module_init for non-modular core intmem.c code
ia64: don't use module_init in non-modular sim/simscsi.c code
ia64: don't use module_init for non-modular core kernel/mca.c code
arm: don't use module_init in non-modular mach-vexpress/spc.c code
powerpc: don't use module_init in non-modular 83xx suspend code
powerpc: use device_initcall for registering rtc devices
x86: don't use module_init in non-modular devicetree.c code
x86: don't use module_init in non-modular intel_mid_vrtc.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qotW
-----END PGP SIGNATURE-----
Merge tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull implicit module.h fixes from Paul Gortmaker:
"Fix up implicit <module.h> users that will break later.
The files changed here are simply modular source files that are
implicitly relying on <module.h> being present. We fix them up now,
so that we can decouple some of the module related init code from the
core init code in the future.
The addition of the module.h include to several files here is also a
no-op from a code generation point of view, else there would already
be compile issues with these files today.
There may be lots more implicit includes of <module.h> in tree, but
these are the ones that extensive build test coverage has shown that
must be fixed in order to avoid build breakage fallout for the pending
module.h <---> init.h code relocation we desire to complete"
* tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
frv: add module.h to mb93090-mb00/flash.c to avoid compile fail
drivers/cpufreq: include <module.h> for modular exynos-cpufreq.c code
drivers/staging: include <module.h> for modular android tegra_ion code
crypto/asymmetric_keys: pkcs7_key_type needs module.h
sh: mach-highlander/psw.c is tristate and should use module.h
drivers/regulator: include <module.h> for modular max77802 code
drivers/pcmcia: include <module.h> for modular xxs1500_ss code
drivers/hsi: include <module.h> for modular omap_ssi code
drivers/gpu: include <module.h> for modular rockchip code
drivers/gpio: include <module.h> for modular crystalcove code
drivers/clk: include <module.h> for clk-max77xxx modular code
Do not leak memory and free irqs in case of an error.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If stm32f4_rcc_lookup() is called with primary == 0 and secondary == 192
then it will read beyond the end of the table array due to an out-by-one
error in the range check.
In addition to the fixing the inequality we also modify the r.h.s. to
make it even more explicit that we are comparing against the size of
table in bits.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Fixes: 358bdf892f ("clk: stm32: Add clock driver for STM32F4[23]xxx devices")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
A 32-bit variable should be type casted to 64-bit before arithmetic
operation and assigning it to a 64-bit variable
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Fixes: 5fe225c105 ("clk: iproc: add initial common clock support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_property_read_string_index takes array of pointers and assign them to
strings read from device tree property. No additional memory allocation
is needed prior to calling of_property_read_string_index. In fact, since
the array of pointers will be re-assigned to other strings, any memory
that it points to prior to calling of_property_read_string_index will be
leaked
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Fixes: 5fe225c105 ("clk: iproc: add initial common clock support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers and updates to existing ones, as usual. There are some fixes to
the framework itself and several cleanups for sparse warnings, etc.
Please consider pulling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Iv72
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.2 are dominated by new
drivers and updates to existing ones, as usual.
There are some fixes to the framework itself and several cleanups for
sparse warnings, etc"
* tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (135 commits)
clk: stm32: Add clock driver for STM32F4[23]xxx devices
dt-bindings: Document the STM32F4 clock bindings
cpufreq: exynos: remove Exynos4210 specific cpufreq driver support
ARM: Exynos: switch to using generic cpufreq driver for Exynos4210
clk: samsung: exynos4: add cpu clock configuration data and instantiate cpu clock
clk: samsung: add infrastructure to register cpu clocks
clk: add CLK_RECALC_NEW_RATES clock flag for Exynos cpu clock support
doc: dt: add documentation for lpc1850-ccu clk driver
clk: add lpc18xx ccu clk driver
doc: dt: add documentation for lpc1850-cgu clk driver
clk: add lpc18xx cgu clk driver
clk: keystone: add support for post divider register for main pll
clk: mvebu: flag the crypto clk as CLK_IGNORE_UNUSED
clk: cygnus: remove Cygnus dummy clock binding
clk: cygnus: add clock support for Broadcom Cygnus
clk: Change bcm clocks build dependency
clk: iproc: add initial common clock support
clk: iproc: define Broadcom iProc clock binding
MAINTAINERS: update email for Michael Turquette
clk: meson: add some error handling in meson_clk_register_cpu()
...
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses
Conflicts:
arch/arm64/boot/dts/arm/juno-motherboard.dtsi
Trivial add/add conflict with our dt branch.
Resolution: take both sides.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=02Gm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Kevin Hilman:
"Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: soc: sunxi: Introduce SoC driver to map SRAMs
arm-cci: Add aliases for PMU events
arm-cci: Add CCI-500 PMU support
arm-cci: Sanitise CCI400 PMU driver specific code
arm-cci: Abstract handling for CCI events
arm-cci: Abstract out the PMU counter details
arm-cci: Cleanup PMU driver code
arm-cci: Do not enable CCI-400 PMU by default
firmware: qcom: scm: Add HDCP Support
ARM: berlin: add an ADC node for the BG2Q
ARM: berlin: remove useless chip and system ctrl compatibles
clk: berlin: drop direct of_iomap of nodes reg property
ARM: berlin: move BG2Q clock node
ARM: berlin: move BG2CD clock node
ARM: berlin: move BG2 clock node
clk: berlin: prepare simple-mfd conversion
pinctrl: berlin: drop SoC stub provided regmap
ARM: berlin: move pinctrl to simple-mfd nodes
pinctrl: berlin: prepare to use regmap provided by syscon
reset: berlin: drop arch_initcall initialization
...
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZtPK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform support updates from Kevin Hilman:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (134 commits)
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
ARM: socfpga: fix build error due to secondary_startup
MAINTAINERS: ARM64: EXYNOS: Extend entry for ARM64 DTS
ARM: ep93xx: simone: support for SPI-based MMC/SD cards
MAINTAINERS: update Shawn's email to use kernel.org one
ARM: socfpga: support suspend to ram
ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fE8E
-----END PGP SIGNATURE-----
Merge tag 'for-4.2' of git://git.sourceforge.jp/gitroot/uclinux-h8/linux
Pull Renesas H8/300 architecture re-introduction from Yoshinori Sato.
We dropped arch/h8300 two years ago as stale and old, this is a new and
more modern rewritten arch support for the same architecture.
* tag 'for-4.2' of git://git.sourceforge.jp/gitroot/uclinux-h8/linux: (27 commits)
h8300: fix typo.
h8300: Always build dtb
h8300: Remove ARCH_WANT_IPC_PARSE_VERSION
sh-sci: Get register size from platform device
clk: h8300: fix error handling in h8s2678_pll_clk_setup()
h8300: Symbol name fix
h8300: devicetree source
h8300: configs
h8300: IRQ chip driver
h8300: clocksource
h8300: clock driver
h8300: Build scripts
h8300: library functions
h8300: Memory management
h8300: miscellaneous functions
h8300: process helpers
h8300: compressed image support
h8300: Low level entry
h8300: kernel startup
h8300: Interrupt and exceptions
...
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Pull clkdev updates from Russell King:
"This series addresses some breakage in clkdev caused by a previous
patch set from the clk tree which introduced per-user clk structures.
This basically renamed the existing 'struct clk' to 'struct clk_hw',
and introduced a new 'struct clk'.
This change will break anyone using clk_add_alias() with the common
clk code enabled. Thankfully, the intersection of users of
clk_add_alias() and those using the common clk code is practically
zero, but this is something which should be fixed to keep the code
sane.
The problem is that clk_add_alias() does this:
r = clk_get(...);
l = clkdev_alloc(r, ...);
clk_put(...);
which causes the alias to store a pointer to 'r', which has been
freed.
The original patch set tried to work around this problem incorrectly -
at clk_get() time, it tried to convert the struct clk to a struct
clk_hw, and then creating a new struct clk from that. Clearly, if the
original struct clk has been freed, then we have a use-after-free bug.
We have other places in the tree which do something similar, so this
series also addresses those locations too.
This series addresses this problem by converting clkdev to store and
use the clk_hw pointer. This allows clk_get() to only have to create
it's per-user struct clk from the clk_hw. We can also get to the
desired clk_hw at clk_add_alias() or clk lookup creation time, when
the struct clk is "alive".
We also perform some cleanups of the code:
- replacing looped calls to clkdev_add() with clkdev_add_table()
- replacing open-coded lookup allocation (which should have been
using clkdev_alloc()) and subsequent clkdev_add() with
clkdev_create()
- replacing open-coded clk_add_alias() with clk_add_alias()"
* 'for-linus-clk' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
clk: s2mps11: use clkdev_create()
ASoC: migor: use clkdev_create()
ARM: omap2: use clkdev_add_alias()
ARM: omap2: use clkdev_create()
ARM: orion: use clkdev_create()
ARM: lpc32xx: convert to use clkdev_add_table()
SH: use clkdev_add_table()
clkdev: add clkdev_create() helper
clkdev: const-ify connection id to clk_add_alias()
clkdev: get rid of redundant clk_add_alias() prototype in linux/clk.h
clkdev: drop __init from clkdev_add_table()
clk: update clk API documentation to clarify clk_round_rate()
clkdev: use clk_hw internally
The error handling was a bit messy and buggy. It freed "pll_clock" then
dereferenced it, and then freed it again. I've re-written it in normal
kernel style.
Fixes: 42ff8e8008c8 ('h8300: clock driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
The driver supports decoding and statically modelling PLL state (i.e.
we inherit state from bootloader) and provides support for all
peripherals that support simple one-bit gated clocks. The covers all
peripherals whose clocks come from the AHB, APB1 or APB2 buses.
It has been tested on an STM32F429I-Discovery board. The clock counts
for TIM2, USART1 and SYSTICK are all set correctly and the wall clock
looks OK when checked with a stopwatch. I have also tested a prototype
driver for the RNG hardware. The RNG clock is correctly enabled by the
framework (also did inverse test and proved that by changing DT to
configure the wrong clock bit then we observe the RNG driver to fail).
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
[sboyd@codeaurora.org: Silence sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently, code of Loongson-2/3 is under loongson directory and code of
Loongson-1 is under loongson1 directory. Besides, there are Kconfig
options such as MACH_LOONGSON and MACH_LOONGSON1. This naming style is
very ugly and confusing. Since Loongson-2/3 are both 64-bit general-
purpose CPU while Loongson-1 is 32-bit SoC, we rename both file names
and Kconfig symbols from loongson/loongson1 to loongson64/loongson32.
[ralf@linux-mips.org: Resolve a number of simple conflicts.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9790/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the clocks provided by the CGU in the Ingenic JZ4780
SoC, making use of the SoC-agnostic CGU code to do the heavy lifting.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Co-authored-by: Paul Cercueil <paul@crapouillou.net>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10157/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The jz4740-cgu driver already has access to the CGU, so it makes sense
to move the few remaining accesses to the CGU from arch/mips/jz4740
there too. Move the jz4740_clock_{suspend,resume} functions there for
such consistency. The arch/mips/jz4740/clock.c file now contains nothing
more of use & so is removed.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10158/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The jz4740-cgu driver already has access to the CGU, so it makes sense
to move the few remaining accesses to the CGU from arch/mips/jz4740
there too. Move the jz4740_clock_udc_{dis,en}able_auto_suspend functions
there for such consistency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10154/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The jz4740-cgu driver already has access to the CGU, so it makes sense
to move the few remaining accesses to the CGU from arch/mips/jz4740
there too. Move jz4740_clock_set_wait_mode for such consistency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10153/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate the JZ4740 & the qi_lb60 board to use common clock framework
via the new Ingenic SoC CGU driver. Note that the JZ4740-specific
debugfs code is removed since common clock framework provides its own
debug capabilities.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Co-authored-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10151/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This driver supports the CGU clocks for Ingenic SoCs. It is generic
enough to be usable across at least the JZ4740 to the JZ4780, and will
be made use of on such devices in subsequent commits. This patch by
itself only adds the SoC-agnostic infrastructure that forms the bulk of
the CGU driver for the aforementioned further commits to make use of.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Co-authored-by: Paul Cercueil <paul@crapouillou.net>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10150/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJVU1EDAAoJEN0jrNd/PrOhYO8QAKDSJXdoVqtQITU3lUDfTB7i
g7EJfL8PjT5i1KTjJHT7/2FFuQlb7eeJexyNV539sIJtUrcDOl6qNVbq/FYNouia
bF7XqOxbR8QpWsYbQ46bzbwBaDd+CPLDwjSounNf6G4kJQy7/9SVr6BBPbLa2LIS
xzxMzr2+/CCmH9P1p2I5ey5f1fQ75DKaz8RGgv3FcltdkKNZQCTa+hthCOdicNJu
BoVHqXgJZvz0tgZk0zdCrKyUi31Gu8CNmFad7jtIS01EHGjBpgSE9m7ViYYRCFl5
GIjVh5IryCg2LJt8JP2mPCFNyiAvjxzMt/hJquzj2x2QMKrK8wgC3BwlrMUPuhkM
xkldCMXY1ImVgTbwFdAEFR08+/VybzfLu4FDZSdG4IeNKfMj0n3EirAX9gE1VHDl
bofkPZsE2Vr4N3jYekjbql3m9ZO8WsnIRz7D/Rd1OIqNyMA3xZQz79zgqQ5EQsB1
+GJztoyIdDikefCAww/z7I+vTTQ8InV/FnuzKN/SyqqLe5Ni9TFg6sCN50cnW2Ps
/wHE0KAEV6Oem0dNOISCd3cx231FAiCKQBSm0sUl0cAQ+x1E/NKs6H7vC0wrvWOo
f7072+BesVG9FPpWUg/lAD95YlPcoFdTDUep9J6mX2RB5ZfVEr9gNN04dY3tt4g2
kl37UB2qRXX0aEdkTWm2
=I0gO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.2-rc1
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
With the addition of the new Samsung specific cpu-clock type, the
arm clock can be represented as a cpu-clock type. Add the CPU clock
configuration data and instantiate the CPU clock type for Exynos4210.
Changes by Bartlomiej:
- fixed issue with wrong dividers being setup by Common Clock Framework
(by an addition of CLK_RECALC_NEW_RATES clock flag to mout_apll clock,
without this change cpufreq-dt driver showed ~10 mA larger energy
consumption when compared to cpufreq-exynos one when "performance"
cpufreq governor was used on Exynos4210 SoC based Origen board), this
was probably meant to be workarounded by use of CLK_GET_RATE_NOCACHE
and CLK_DIVIDER_READ_ONLY clock flags in the original patchset (in
"[PATCH v12 6/6] clk: samsung: remove unused clock aliases and update
clock flags") but using these flags is not sufficient to fix the issue
observed
- removed Exynos5250 and Exynos5420 support for now
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The CPU clock provider supplies the clock to the CPU clock domain. The
composition and organization of the CPU clock provider could vary among
Exynos SoCs. A CPU clock provider can be composed of clock mux, dividers
and gates. This patch defines a new clock type for CPU clock provider and
adds infrastructure to register the CPU clock providers for Samsung
platforms.
Changes by Bartlomiej:
- fixed issue with setting lower dividers before the parent clock speed
was lowered (the issue resulted in lockup on Exynos4210 SoC based
Origen board when "ondemand" cpufreq governor was stress tested)
- fixed missing spin_unlock on error in exynos_cpuclk_post_rate_change()
problem by moving cfg_data search outside of the spin locked area
- removed leftover kfree() in exynos_register_cpu_clock() that could
result in dereferencing the NULL pointer on error
- moved spin_lock earlier in exynos_cpuclk_pre_rate_change() to cover
reading of E4210_SRC_CPU and E4210_DIV_CPU1 registers
- added missing "last chance" checks to wait_until_divider_stable() and
wait_until_mux_stable() (needed in case that IRQ handling took long
time to proceed and resulted in function printing incorrect error
message about timeout)
- moved E4210_CPU_DIV[0,1]() macros just before their only users,
this resulted in moving them from patch #2 to patch #3/6 ("clk:
samsung: exynos4: add cpu clock configuration data and instantiate
cpu clock")
- removed E5250_CPU_DIV[0,1](), E5420_EGL_DIV0() and E5420_KFC_DIV()
macros for now
- added my Copyrights to drivers/clk/samsung/clk-cpu.c
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This flag is needed to fix the issue with wrong dividers being setup
by Common Clock Framework when using the new Exynos cpu clock support.
The issue happens because clk_core_set_rate_nolock() calls
clk_calc_new_rates(clk, rate) before both pre/post clock notifiers have
a chance to run. In case of Exynos cpu clock support pre/post clock
notifiers are registered for mout_apll clock which is a parent of armclk
cpu clock and dividers are modified in both pre and post clock notifier.
This results in wrong dividers values being later programmed by
clk_change_rate(top). To workaround the problem CLK_RECALC_NEW_RATES
flag is added and it is set for mout_apll clock later so the correct
divider values are re-calculated after both pre and post clock notifiers
had run.
For example when using "performance" governor on Exynos4210 Origen board
the cpufreq-dt driver requests to change the frequency from 1000MHz to
1200MHz and after the change state of the relevant clocks is following:
Without use of CLK_GET_RATE_NOCACHE flag:
fout_apll rate: 1200000000
fout_apll_div_2 rate: 600000000
mout_clkout_cpu rate: 600000000
div_clkout_cpu rate: 600000000
clkout_cpu rate: 600000000
mout_apll rate: 1200000000
armclk rate: 1200000000
mout_hpm rate: 1200000000
div_copy rate: 300000000
div_hpm rate: 300000000
mout_core rate: 1200000000
div_core rate: 1200000000
div_core2 rate: 1200000000
arm_clk_div_2 rate: 600000000
div_corem0 rate: 300000000
div_corem1 rate: 150000000
div_periph rate: 300000000
div_atb rate: 300000000
div_pclk_dbg rate: 150000000
sclk_apll rate: 1200000000
sclk_apll_div_2 rate: 600000000
With use of CLK_GET_RATE_NOCACHE flag:
fout_apll rate: 1200000000
fout_apll_div_2 rate: 600000000
mout_clkout_cpu rate: 600000000
div_clkout_cpu rate: 600000000
clkout_cpu rate: 600000000
mout_apll rate: 1200000000
armclk rate: 1200000000
mout_hpm rate: 1200000000
div_copy rate: 200000000
div_hpm rate: 200000000
mout_core rate: 1200000000
div_core rate: 1200000000
div_core2 rate: 1200000000
arm_clk_div_2 rate: 600000000
div_corem0 rate: 300000000
div_corem1 rate: 150000000
div_periph rate: 300000000
div_atb rate: 240000000
div_pclk_dbg rate: 120000000
sclk_apll rate: 150000000
sclk_apll_div_2 rate: 75000000
Without this change cpufreq-dt driver showed ~10 mA larger energy
consumption when compared to cpufreq-exynos one when "performance"
cpufreq governor was used on Exynos4210 SoC based Origen board.
This issue was probably meant to be workarounded by use of
CLK_GET_RATE_NOCACHE and CLK_DIVIDER_READ_ONLY clock flags in
the original Exynos cpu clock patchset (in "[PATCH v12 6/6] clk:
samsung: remove unused clock aliases and update clock flags" patch)
but usage of these flags is not sufficient to fix the issue observed.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Trivial fix that prevents to compile this pmc clock driver if h32mx clock is
present but smd clock isn't.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes: bcc5fd49a0 ("clk: at91: add a driver for the h32mx clock")
Cc: <stable@vger.kernel.org> # 3.18+
Fix the PERIPHERAL_MAX_SHIFT definition (3 instead of 4) and adapt the
round_rate and set_rate logic accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: "Wu, Songjun" <Songjun.Wu@atmel.com>
The PLL impose a certain input range to work correctly, but it appears that
this input range does not apply on the input clock (or parent clock) but
on the input clock after it has passed the PLL divisor.
Fix the implementation accordingly.
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Jonas Andersson <jonas@microbit.se>
Add driver for NXP LPC18xx/43xx Clock Control Unit (CCU). The CCU
provides fine grained gating of most clocks present in the SoC.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Add driver for NXP LPC18xx/43xx Clock Generation Unit (CGU). The CGU
contains several clock generators and output stages that route the
clocks either directly to peripherals or to a Clock Control Unit
(CCU).
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Main PLL controller has post divider bits in a separate register in
pll controller. Use the value from this register instead of fixed
divider when available.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
One error fix, and one patch to add support for the USB clock found on the
Allwinner A23 and A33
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVfdWlAAoJEBx+YmzsjxAgijIP/1j0EcaRZOaEkLWDOSSQ4av5
jH/NrMhpnYJRHPgVZg9KgcF8znOIQdutxy67ScpMHpQ2x+1yw7qZ+ET4Y6hCTz0g
Z1jUYgwuf1yu0j18VZ7SJQhIWjsOLlOyOyXwzwEUEfJe0p/+h1msQNfW2wqZvvBf
ognuEDCduhz2JxmE8Jmcm4RlrVFntcaUilv/abW/oEsWWbPBU6oAt5YkQuCGmxvC
oxeyK0UiUAzEh6nq0XoSz6tATAFjo1yLefrH0GlTZUeg4GmUbPmrvKmSRQFOWDnB
drWDl/HKWehW/EcK8YcUhhfYJk5NFyYHxYDODHD91xAj1iGAvPO8mmLn0Wl75Tkn
oAI/qyUL7brNRpDW4NirAP0+AIgsD6YrAxbZof811+FlJ0WZ9M4i+hIIzzgq31gL
Tw5qSSQ730VtJQfgNlDFL6mHxqKM7s/UzHJbIZirEs4FFHEYvOLdOfHqv7ACDAif
goYN4M40htseU80rYOfZFrbaNta13Eh7Lqdmi5mat7OJNvhcONbxe9P3kc4BTGbc
VRydPObMJzIdRFxJEp3Gu+D/NLSHyJ7O3WwH6OxTQBwnASMMfOutPycdbMZoZXc1
2NQPQq6xhwFIZI2G1uD45Dnt3qX8qQqeLce8UItLIlHZGN3c6hjerQ/+Y+gR4BKY
TA15OfxbP/ZgP31xgYC0
=uxrz
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Allwinner clocks additions for 4.2
One error fix, and one patch to add support for the USB clock found on the
Allwinner A23 and A33
The crypto SRAM, used by the armada 370 cpuidle code to workaround a bug
in the BootROM code, requires the crypto clk to be up and running.
Flag the crypto clk as IGNORE_UNUSED until we add the proper
infrastructure to define the crypto SRAM in the DT and reference the crypto
clk in this SRAM node.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The Broadcom Cygnus SoC is architected under the iProc architecture. It
has the following PLLs: ARMPLL, GENPLL, LCPLL0, MIPIPLL, all dervied
from an onboard crystal. Cygnus also has various ASIU clocks that are
derived directly from the onboard crystal.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The clock code under drivers/clk/bcm now contains code for both the
Broadcom mobile SoCs and the iProc SoCs. Change the the makefile
dependency to be under config flag CONFIG_ARCH_BCM that's enabled for
both families of SoCs
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This adds basic and generic support for various iProc PLLs and clocks
including the ARMPLL, GENPLL, LCPLL, MIPIPLL, and ASIU clocks.
SoCs under the iProc architecture can define their specific register
offsets and clock parameters for their PLL and clock controllers. These
parameters can be passed as arugments into the generic iProc PLL and
clock setup functions
Derived from code originally provided by Jonathan Richardson
<jonathar@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This driver builds based on obj-y and hence will not ever be
modular. Change it to use the non-modular registration so that it
won't suffer a compile fail once a header move places the modular
registration within the module.h file.
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The clk-nomadik.o is built for ARCH_NOMADIK -- which is bool, and
hence this code is either present or absent. It will never be
modular, so using module_init as an alias for __initcall can be
somewhat misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- it will remain at level 6 in initcall ordering.
Cc: Mike Turquette <mturquette@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files are built off of the tristate COMMON_CLK_MAX77686 and
COMMON_CLK_MAX77802 respectively. They also contains modular function
calls so they should explicitly include module.h to avoid compile
breakage during header shuffles done in the future.
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This error handling hopefully isn't needed but it make the static
checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
A recent change to mark parent names as const missed this struct
member so we get warnings like:
drivers/clk/pxa/clk-pxa25x.c:122:2: warning: initialization
discards 'const' qualifier from pointer target type
Fix it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* zte/soc:
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
It adds a clock driver for zx296702 SoC to register the clock tree to
Common Clock Framework. All the clocks of bus topology and some the
peripheral clocks are ready with this commit. Some missing leaf clocks
for peripherals will be added later when needed.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- Add new SoC i.MX7D support, which integrates two Cortex-A7 and one
Cortex-M4 cores.
- Support suspend from IRAM on i.MX53, so that DDR pins can be set to
high impedance for more power saving during suspend.
- Move i.MX clock drivers from arch/arm/mach-imx to drivers/clk/imx.
- Move i.MX GPT timer driver from arch/arm/mach-imx into
drivers/clocksource.
- A couple of clock driver update for VF610 and i.MX6Q.
- A few random code correction and improvement.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVb7grAAoJEFBXWFqHsHzOWS0H/RXV1UjvsJTfK8+KR2SGY5QO
3hU4YQYpnkukG2OtxAaWKXzIh+xeINqJ02cws/zyEfVZFsZp/i5Z7EM5811qQeNC
f9uCtFCNynTnWjUP9YXELgAX3/DPHMr+Em5QGOWwh+311YypJyP7CttsJvmjJIUN
qGYXdpy2xhqKgSGrnI+dhpxTdhtm/jmsggoM8qqi2aYB3c3rnWCc6QSBMR8oxFKB
Tmxd/cc/6Pvbp7W+AztTb/z8UD21UJkn96FhUb9563HKjf7kvbP4ydJTwhBxfyQu
YxE4kkejrnVNaUl1Tkqmf7rTgLKaU92nrLCuBDI/91OET+GQtq2R5fE8iMPs29k=
=c254
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
The i.MX SoC updates for 4.2:
- Add new SoC i.MX7D support, which integrates two Cortex-A7 and one
Cortex-M4 cores.
- Support suspend from IRAM on i.MX53, so that DDR pins can be set to
high impedance for more power saving during suspend.
- Move i.MX clock drivers from arch/arm/mach-imx to drivers/clk/imx.
- Move i.MX GPT timer driver from arch/arm/mach-imx into
drivers/clocksource.
- A couple of clock driver update for VF610 and i.MX6Q.
- A few random code correction and improvement.
* tag 'imx-soc-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (44 commits)
ARM: imx: imx7d requires anatop
clocksource: timer-imx-gpt: remove include of <asm/mach/time.h>
ARM: imx: move timer driver into drivers/clocksource
ARM: imx: remove platform headers from timer driver
ARM: imx: provide gpt device specific irq functions
ARM: imx: get rid of variable timer_base
ARM: imx: define gpt register offset per device type
ARM: imx: move clock event variables into imx_timer
ARM: imx: set up .set_next_event hook via imx_gpt_data
ARM: imx: setup tctl register in device specific function
ARM: imx: initialize gpt device type for DT boot
ARM: imx: define an enum for gpt timer device type
ARM: imx: move timer resources into a structure
ARM: imx: use relaxed IO accessor in timer driver
ARM: imx: make imx51/3 suspend optional
ARM: clk-imx6q: refine sata's parent
ARM: imx: clk-v610: Add clock for I2C2 and I2C3
ARM: mach-imx: iomux-imx31: Use DECLARE_BITMAP
ARM: imx: add imx7d clk tree support
ARM: clk: imx: update pllv3 to support imx7
...
Conflicts:
arch/arm/mach-imx/Kconfig
The debug_node field is only used when DEBUG_FS config is selected,
so declare it only if DEBUG_FS is selected.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently it is not made explicit why clk_fixed_set_rate() can ignore
its arguments and unconditionally return success. Add a comment
to explain this.
We also mark the clk_ops table const since it should never be
modified at runtime.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-cdce925.c:550: warning: format ‘%u’ expects type
‘unsigned int’, but argument 6 has type ‘size_t’
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This line was indented too far.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This patch adds 'CLK_IGNORE_UNUSED' flag to clocks which is required for
operation of secure monitor call (smc). System will hang when it executes 'smc'
with one of those clock is gated. All related clocks must be enabled.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds the CLK_SET_RATE_PARENT flag for 'aclk_g3d' clock and parent
clocks becuase 'aclk_g3d' is used to change GPU frequency for DVFS (Dynamic
Voltage Frequency Scaling) feature and adds CLK_IGNORE_UNUSED flags to
'aclk_asyncapbs_g3d'/'aclk_asyncapbm_g3d' clocks to access the SFR
of the MALI device.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
[cw00.choi: Add patch description and add CLK_SET_RATE_PARENT to 'aclk_g3d' clk]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This DIV_CPIF register must be stored when the system is suspended, and must
be restored on system resume. This patch adds the register to the list of
restored registers.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds CLK_SET_RATE_PARENT flag to support DVFS of Cortex-{A53|A57}
core (big.LITTLE core) because 'sclk_{apollo|atlas}' leaf clock is used to
change the CPU frequency of Cortex-{A53|A57} core in arm_big_little.c driver.
- 'apollo' word means the LITTLE core (Cortex-A53 core) in Exynos5433 TRM.
- 'atlas' word means the big core (Cortex-A57 core) in Exynos5433 TRM.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Use of_clk_parent_fill to fill in the parent clock's array.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sprinkled all through the platform clock drivers are code like this to
fill the clock parent array:
for (i = 0; i < num_parents; ++i)
parent_names[i] = of_clk_get_parent_name(np, i);
The of_clk_parent_fill() will do the same as the code above, and while
at it, return the number of parents as well since the logic of the
function is to the walk the clock node to look for the parent.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
[sboyd@codeaurora.org: Fixed kernel-doc]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-meson8b:
clk: meson8b: Add support for Meson8b clocks
clk: meson: Document bindings for Meson8b clock controller
clk: meson: Add support for Meson clock controller
This patch adds support for the basic clocks found on the Amlogic
Meson8b SoCs.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patchset adds the infrastructure for registering and managing the
core clocks found on Amlogic MesonX SoCs. In particular:
- PLLs
- CPU clock
- Fixed rate clocks, fixed factor clocks, ...
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since commit 2893c37946 ("clk: make strings in parent name arrays
const") the name of parent clocks can be const. So add more const in
several clock drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The size of clk_data should be the same as CLK_APMIXED_NR_CLK
instead of ARRAY_SIZE(plls). CLK_APMIXED_* is numbered from 1, so
CLK_APMIXED_NR_CLK will be greater than ARRAY_SIZE(plls).
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When setting the PLL rates, check that:
- VCO is within range
- PFD is within range
- PLL is disabled when postdiv is changed
- postdiv2 <= postdiv1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently, when the rate is changed, the driver makes sure the
PLL is enabled before doing so. This is done because the PLL
cannot be locked while disabled. Once locked, the drivers
returns the PLL to its previous enable/disable state.
This is a bit cumbersome, and can be simplified.
This commit reworks the .set_rate() functions for the integer
and fractional PLLs. Upon rate change, the PLL is now locked
only if it's already enabled.
Also, the driver locks the PLL on .enable(). This makes sure
the PLL is locked when enabled, and not locked when disabled.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This commit adds a pll_lock() helper making the code more readable.
Cosmetic change only, no functionality changes.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Timer has external fast clock, and it is a mux clock.
Add the timer clock type for timer driver.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The suggested value in the mmp2 manual is wrong.
There are only 13 bits for numerator, but some suggested
value has 14 bits.
Fix the factor tabled and remove the unused items.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
DESHDCP clock is needed on DRA7 based SoCs to enable the DSS IP. That
clock is an odd one, as it is not supposed to be any kind of core clock
for DSS, and we don't even support HDCP, but the clock is still needed
even for the HWMOD framework to be able to reset the DSS IP.
As there's no support for multiple core clocks in the HWMOD framework,
we don't have any obvious place to enable this clock when DSS IP is
being enabled.
Furthermore, the HDMI on OMAP5 DSS is the same as on DRA7, and OMAP5
does not have any such clock configuration bit. This suggests that on
OMAP5 the DESHDCP clock is always enabled, and for DRA7 we have the
possibility to gate it.
So, as we don't have any clean way to enable and disable the clock
based on the need, this patch enables the clock at boot time, making it
work similarly to OMAP5.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
This driver supports the TI CDCE925 programmable clock synthesizer.
The chip contains two PLLs with spread-spectrum clocking support and
five output dividers. The driver only supports the following setup,
and uses a fixed setting for the output muxes:
Y1 is derived from the input clock
Y2 and Y3 derive from PLL1
Y4 and Y5 derive from PLL2
Given a target output frequency, the driver will set the PLL and
divider to best approximate the desired output.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Even if not documented in the datasheet, the Armada 370 SoC can actually
gate the CESA (crypto engine) clock.
Add an entry in the gating_desc table to be able to reference the CESA
gateclk in the crypto node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add clock drivers for hi6220 SoC, this driver controls the SoC
registers to supply different clocks to different IPs in the SoC.
We add one divider clock for hi6220 because the divider in hi6220
also has a mask bit but it doesnot obey the rule defined by flag
"CLK_DIVIDER_HIWORD_MASK", we can not get index of the mask bit by
left shift fixed bits (e.g. 16 bits), so we add this divider clock
to handle it.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
__init markings on function prototypes are useless, so remove
them.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add a new Linux clock for DRA7 based SoCs to control DESHDCP clock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Define an enum for gpt timer device type in include/soc/imx/timer.h to
tell the gpt block differences among SoCs. Update non-DT users (clock
drivers) to pass the device type.
As we now have include/soc/imx/timer.h, the declaration of
mxc_timer_init() is moved into there as the best fit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for clock gating of I2C2 and I2C3.
We use I2C2 in a (not yet mainlined) device tree.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add i.MX7D clk tree support.
Enable all clock to bring up imx7.
Clock framework need be modified a little since imx7d
change clock design. otherwise system will halt and block the
other part upstream.
All clock refine need wait for Dong Aisheng's patch
clk: support clocks which requires parent clock on during operation
Or other solution ready.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enabled DAP (debug access port) by default. This enables the hw-
breakpoint framework to make use of the breakpoints and watchpoints
supported by hardware.
[ 0.215805] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.224624] hw-breakpoint: maximum watchpoint size is 4 bytes.
Without this clock, the hw-breakpoint driver claims an undefined
instruction during initialization:
[ 0.227380] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.227519] hw-breakpoint: CPU 0 failed to disable vector catch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Include the "clk.h" header file to fix the following sparse warning:
drivers/clk/imx/clk-cpu.c:77:12: warning: symbol 'imx_clk_cpu' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The definition of do_div uses unsigned long long
variable as its first parameter, better to pass
a u64 variable as first parameter when calling
do_div function.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
EPIT provides another timer implementation besides the default GPT
timer. The imx35 clock driver will use EPIT timer when option
CONFIG_MXC_USE_EPIT is enabled. However, initializing timers from
clock driver is a workaround solution and causes problem when we move
clock drivers into driver/clk.
Let's simply drop the EPIT initialization from there. If people really
want this EPIT option, EPIT timer driver needs to be reworked to do the
initialization in a standard way - use CLOCKSOURCE_OF_DECLARE() with
device tree support.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
After the cleanup on clock drivers, they are now ready to be moved into
drivers/clk. Let's move them into drivers/clk/imx folder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
With most of the clock code under clock driver already, the low-level
register access code, and the init code for the same, is no longer
needed outside the clock driver. Thus, these can be moved under clock
driver also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We should avoid exporting data from drivers, instead use an API for
registering the clock low level operations.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Several exported TI clock driver features are no longer needed outside
the clock driver itself, thus move all of these to the driver private
header file. Also, update some of the driver files to actually include
this header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With legacy clock support gone, this is no longer needed under platform,
so move it under the clock driver itself. Make some exports be driver
internal definitions at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove unnecessary declarations
from the TI clock header also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove the exported clock driver
APIs as well, as these are not needed outside clock driver anymore.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, this is no longer needed under
platform code-base. Thus, move this under the TI clock driver, and
remove the exported API from the public header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy support gone, OMAP2+ default gate clock can be moved
under clock driver. Create a new file for the purpose, and clean-up
the header exports a bit as some clock APIs are no longer needed
outside clock driver itself.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, OMAP3 generic DPLL code can now be
moved over to the clock driver also. A few un-unused clkoutx2 functions
are also removed at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer used outside clock driver, so move it under the driver
and remove the export for it from the global header file.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer needed in platform directory, as the legacy clock data
is gone, so move it under TI clock driver. Some static functions are
renamed also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP interface clock implementation
can be moved under the clock driver. Some temporary header file tweaks are
also needed to make this change work properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP4 specific DPLL implementations
can be moved under the clock driver. Change some of the function prototypes
to be static at the same time, and remove some exports from the global TI
clock driver header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data now gone, we can start moving OMAP clock
type implementations under clock driver. Start this with moving the
generic OMAP DPLL clock type under TI clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
As most of the clock driver support code is going to be moved under
drivers/clk/ti, an API for setting / getting the SoC specific clock
features is needed. This patch provides this API and changes the
existing code to use it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The usb-clk on sun8i a23 and a33 SoCs is similar to the ones found
on sun6i-a31 SoCs but instead of a 3th phy the a23 / a33 have a hsic
interface which gets enabled by almost the same bits as used on
the a31 for the 3rd phy, but not exactly the same bits so we need
a new compatible for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Add the NSS/GMAC clocks and the TCM clock and NSS resets.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clocks on the Arria 10 platform is a bit different than the
Cyclone/Arria 5 platform that it should just have it's own
driver.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There are 5 possible parent clocks for the SoCFPGA Arria10. Move the define
SYSMGR_SDMMC_CTRL_SET and streq() to clk.h so that the Arria clock driver
can use.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove a previously registered clock provider when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
the hardware node includes both clock and reset support, so it
is named as "car".
this patch implements Flexible clocks(mux, divider, gate), Selectable
clock(mux, divider, gate), root clock(gate),leaf clock(gate), others.
it also implements the reset controller functionality.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The variable init (struct clk_init_data) is allocated on the stack.
We weren't initializing the .flags field, so it contains random junk,
which can cause all kinds of interesting issues when the flags are
parsed by clk_register.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Berlin clock driver was sharing a DT node with the pin controller
and the reset driver. All these devices are now sub-nodes of the chip
controller. This patch rework the Berlin clock driver to allow moving
the Berlin clock DT bindings into their own sub-node of the chip
controller node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Prepare conversion of berlin clk drivers to a simple-mfd sub-node by
checking for parent node compatible. If parent node is "syscon" compatible
use it for of_iomap instead of the own node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add initial clock support for Marvell PXA1928. The PXA1928 is a mobile
SOC and is similar to other MMP/PXA series of SOCs, so a lot of the
existing infrastructure is reused here.
Currently the PLLs are just fixed clocks, and not all leaf clocks are
implemented.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch shows the correct information for debugging when fail
to set clock rate because original error message shows the error
value instead of current clock rate.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Having this Kconfig sourced outside the clk menu means the option
is under the "Device Drivers" menu instead of the "Common Clock
Framework" menu. Move it so that the bcm clock config options are
in the right place.
Cc: Alex Elder <elder@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-u300.c:1175:13: warning: symbol 'u300_clk_init' was not declared. Should it be static?
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-moxart.c:18:13: warning: symbol 'moxart_of_pll_clk_init' was not declared. Should it be static?
drivers/clk/clk-moxart.c:56:13: warning: symbol 'moxart_of_apb_clk_init' was not declared. Should it be static?
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-xgene.c:77:43: warning: incorrect type in argument 1 (different address spaces)
drivers/clk/clk-xgene.c:77:43: expected void *csr
drivers/clk/clk-xgene.c:77:43: got void [noderef] <asn:2>*
...
drivers/clk/clk-xgene.c: In function ‘xgene_clk_enable’:
drivers/clk/clk-xgene.c:237:3: warning: format ‘%LX’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘phys_addr_t’ [-Wformat]
drivers/clk/clk-xgene.c:248:3: warning: format ‘%LX’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘phys_addr_t’ [-Wformat]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/mmp/clk-apbc.c:118:16: warning: symbol 'clk_apbc_ops' was not declared. Should it be static?
drivers/clk/mmp/clk-apmu.c:64:16: warning: symbol 'clk_apmu_ops' was not declared. Should it be static?
Cc: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/versatile/clk-sp810.c:159:29: error: incompatible types for operation (<=)
drivers/clk/versatile/clk-sp810.c:159:29: left side has type char const *<noident>
drivers/clk/versatile/clk-sp810.c:159:29: right side has type int
drivers/clk/versatile/clk-sp810.c:159:53: error: incompatible types for operation (<=)
drivers/clk/versatile/clk-sp810.c:159:53: left side has type char const *<noident>
drivers/clk/versatile/clk-sp810.c:159:53: right side has type int
drivers/clk/versatile/clk-sp810.c:138:13: warning: symbol 'clk_sp810_of_setup' was not declared. Should it be static?
Acked: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/ti/clk.c:125:31: warning: incorrect type in return expression (different address spaces)
drivers/clk/ti/clk.c:125:31: expected void [noderef] <asn:2>*
drivers/clk/ti/clk.c:125:31: got void *
drivers/clk/ti/clk.c:132:31: warning: incorrect type in return expression (different address spaces)
drivers/clk/ti/clk.c:132:31: expected void [noderef] <asn:2>*
drivers/clk/ti/clk.c:132:31: got void *
drivers/clk/ti/dpll.c:180:14: warning: symbol '_get_reg' was not declared. Should it be static?
drivers/clk/ti/fapll.c:624:32: warning: Using plain integer as NULL pointer
drivers/clk/ti/fapll.c:625:31: warning: Using plain integer as NULL pointer
drivers/clk/ti/fapll.c:630:40: warning: Using plain integer as NULL pointer
drivers/clk/ti/clk-dra7-atl.c:158:22: warning: symbol 'atl_clk_ops' was not declared. Should it be static?
drivers/clk/ti/clk-dra7-atl.c:170:39: warning: Using plain integer as NULL pointer
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/st/clkgen-mux.c:134:4: warning: symbol 'clkgena_divmux_get_parent' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:171:15: warning: symbol 'clkgena_divmux_recalc_rate' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:218:12: warning: symbol 'clk_register_genamux' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:388:13: warning: symbol 'st_of_clkgena_divmux_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:488:13: warning: symbol 'st_of_clkgena_prediv_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:625:13: warning: symbol 'st_of_clkgen_mux_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:702:13: warning: symbol 'st_of_clkgen_vcc_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:273:15: warning: symbol 'recalc_stm_pll800c65' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:300:15: warning: symbol 'recalc_stm_pll1600c65' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:324:15: warning: symbol 'recalc_stm_pll3200c32' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:346:15: warning: symbol 'recalc_stm_pll1200c32' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:565:19: warning: incorrect type in assignment (different address spaces)
drivers/clk/st/clkgen-pll.c:565:19: expected void [noderef] <asn:2>*reg
drivers/clk/st/clkgen-pll.c:565:19: got void *
drivers/clk/st/clkgen-pll.c:576:18: warning: incorrect type in assignment (different address spaces)
drivers/clk/st/clkgen-pll.c:576:18: expected void [noderef] <asn:2>*reg
drivers/clk/st/clkgen-pll.c:576:18: got void *
drivers/clk/st/clkgen-pll.c:693:53: warning: incorrect type in argument 2 (different address spaces)
drivers/clk/st/clkgen-pll.c:693:53: expected void *[noderef] <asn:2>reg
drivers/clk/st/clkgen-pll.c:693:53: got void [noderef] <asn:2>*[assigned] pll_base
drivers/clk/st/clkgen-fsyn.c:495:5: warning: symbol 'clk_fs660c32_vco_get_rate' was not declared. Should it be static?
drivers/clk/st/clkgen-fsyn.c:522:5: warning: symbol 'clk_fs660c32_vco_get_params' was not declared. Should it be static?
drivers/clk/st/clk-flexgen.c:119:15: warning: symbol 'flexgen_recalc_rate' was not declared. Should it be static?
drivers/clk/st/clk-flexgen.c:177:12: warning: symbol 'clk_register_flexgen' was not declared. Should it be static?
drivers/clk/st/clk-flexgen.c:263:13: warning: symbol 'st_of_flexgen_setup' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These are __iomem pointers. Mark them appropriately so we don't
get sparse errors like
drivers/clk/sirf/clk-common.c:60:16: warning: incorrect type in argument 1 (different address spaces)
drivers/clk/sirf/clk-common.c:60:16: expected void const volatile [noderef] <asn:2>*addr
drivers/clk/sirf/clk-common.c:60:16: got void *
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/shmobile/clk-emev2.c:37:14: warning: symbol 'smu_base' was not declared. Should it be static?
Cc: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Cc: Magnus Damm <damm@opensource.se>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/samsung/clk-exynos5260.c:138:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:328:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:392:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:494:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:583:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:644:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:779:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:898:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:962:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1018:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1165:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1373:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1829:40: warning: Using plain integer as NULL pointer
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/hisilicon/clk-hix5hd2.c:255:13: warning: symbol 'hix5hd2_clk_register_complex' was not declared. Should it be static?
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/berlin/berlin2-pll.c:94:12: warning: symbol 'berlin2_pll_register' was not declared. Should it be static?
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This list doesn't look to be used. Let's remove it and any
associated code that would be manipulating this list. This also
silences this error:
drivers/clk/bcm/clk-kona-setup.c:24:1: warning: symbol 'ccu_list' was not declared. Should it be static?
Reviewed-by: Alex Elder <elder@linaro.org>
Cc: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-max-gen.c:82:16: warning: symbol 'max_gen_clk_ops' was not declared. Should it be static?
drivers/clk/clk-max-gen.c:109:5: warning: symbol 'max_gen_clk_probe' was not declared. Should it be static?
drivers/clk/clk-max-gen.c:183:5: warning: symbol 'max_gen_clk_remove' was not declared. Should it be static?
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk.c:2700:5: warning: symbol '__clk_get' was not declared. Should it be static?
drivers/clk/clk.c:2713:6: warning: symbol '__clk_put' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This function is marked as __init, so exposing it to modules
doesn't make any sense and it isn't used by modules anyway.
drivers/clk/clk-gpio-gate.c:192:13: warning: symbol 'of_gpio_gate_clk_setup' was not declared. Should it be static?
Cc: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Printing an error on kmalloc() failures is unnecessary. Remove
the print and use *ptr in sizeof() for future-proof code.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_clk_get_from_provider() returns ERR_PTR on failure. The
dra7-atl-clock driver was not checking its return value and
immediately used it in __clk_get_hw(). __clk_get_hw()
dereferences supplied clock, if it is not NULL, so in that case
it would dereference an ERR_PTR.
Fixes: 9ac33b0ce8 ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the following compiler warning:
drivers/clk/clk-axm5516.c: In function 'axmclk_probe':
drivers/clk/clk-axm5516.c:559:2: warning: format '%u' expects argument of type 'unsigned int', but argument 2 has type 'size_t' [-Wformat=]
pr_info("axmclk: supporting %u clocks\n", num_clks);
^
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_io_request_and map returns an error pointer, but the current code assumes
that on error the returned pointer will be NULL.
Obviously, that makes the check completely useless. Change the test to actually
check for the proper error code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
MS6 and MS7 do not have the MSx_P3 field. Do the 'params.p3 == 0'
check for MS0-M5 only. See [AN619, p. 6] for details.
Referenced document:
[AN619] Manually Generating an Si5351 Register Map, Rev. 0.4
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The divider calculation for multisynth 6 and 7 differs from the
calculation for multisynth 0-5.
For MS6 and MS7, set MSx_P1 directly, MSx_P1=divide value
[AN619, p. 6].
Referenced document:
[AN619] Manually Generating an Si5351 Register Map, Rev. 0.4
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The HDA to codec clock is named hda2codec_2x, so use the proper name in
the clock table.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EMC clock driver uses symbols exported by the EMC driver, so it
needs the corresponding dependency to avoid build breakage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
As opposed to round_rate(), determine_rate() can take rate constraints
into account when choosing the best rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra124, as we now have a proper driver for the EMC.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver is currently only tested on Tegra124 Jetson TK1, but should
work with other Tegra124 boards, provided that correct EMC tables are
provided through the device tree. Older chip models have differing
timing change sequences, so they are not currently supported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
[treding@nvidia.com: use more consistent function names]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock has never been able to do anything.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
To be used by clock implementations for switching to a new parent during
rate change.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add 2 clocks which were erronously forgotten by the clock framework
port, namely :
- sa1100-rtc
- irda for pxa2xx-ir:UARTCLK
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Michael Turquette <mturquette@linaro.org>
Since pxa clocks were ported to the clock framework, an ordering issue
appears between clocks and clocksource initialization. As a consequence,
the pxa timer clock cannot be acquired in pxa_timer, and is disabled by
clock framework because it is "unused".
The ordering issue is that in the kernel boot sequence :
start_kernel()
...
time_init()
-> pxa_timer()
-> here the clocksource is initialized
...
rest_init()
kernel_init()
initcalls
-> here the clocks are initialized
In the current sequence, the clocks are initialized way after pxa_timer,
which cannot acquire the OSTIMER0 clock.
To solve this issue, the clocks initialization is moved to pxa_timer(),
so that clocks are initialized before clocksource for non device-tree.
For device-tree, the standard arm time_init() will take care of the
ordering.
Reviewed-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
When registering clk-si5351 by platform_data, we should not pass struct clk
for the reference clocks. Drop struct clk from platform_data and rework the
driver to use devm_clk_get of named clock references.
While at it, check for at least one valid input clock and properly prepare/
enable valid reference clocks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: Michael Welling <mwelling@ieee.org>
Reported-by: Jean-Francois Moine <moinejf@free.fr>
Reported-by: Russell King <rmk+linux@arm.linux.org.uk>
Tested-by: Michael Welling <mwelling@ieee.org>
Tested-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
We don't check to make sure the enable_lock is held across
enable/disable and we don't check if the prepare_lock is held
across prepare/unprepare. Add some asserts to catch any future
locking problems.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The APEATCLK and APETRACECLK are actually scaleable so register
them as scaleable clocks.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
clk_dump() will dump data about all clocks in JSON
format, but it misses a newline character at the
end of the JSON string. This patch adds that missing
newline character.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[sboyd@codeaurora.org: Squelch checkpatch with seq_puts()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Before commit 035a61c314 ("clk: Make clk API return per-user
struct clk instances") we acquired the enable_lock in
__clk_set_parent_{before,after}() by means of calling
clk_enable(). After commit 035a61c314 we use clk_core_enable()
in place of the clk_enable(), and clk_core_enable() doesn't
acquire the enable_lock. This opens up a race condition between
clk_set_parent() and clk_enable(). Fix it.
Fixes: 035a61c314 ("clk: Make clk API return per-user struct clk instances")
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
clkdev_create() is a shorter way to write clkdev_alloc() followed by
clkdev_add(). Use this instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a helper to allocate and add a clk_lookup structure. This can not
only be used in several places in clkdev.c to simplify the code, but
more importantly, can be used by callers of the clkdev code to simplify
their clkdev creation and registration.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The connection id is only passed to clk_get() which is already const.
Const-ify this argument too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We want to be able to call clkdev_add_table() from non-init code, so we
need to drop the __init marker from it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clk_add_alias() calls clk_get() followed by clk_put() but in between
those two calls it saves away the struct clk pointer to a clk_lookup
structure. This leaves the 'clk' member of the clk_lookup pointing at
freed memory on configurations where CONFIG_COMMON_CLK=y. This is a
problem because clk_get_sys() will eventually try to dereference the
freed pointer by calling __clk_get_hw() on it. Fix this by saving away
the struct clk_hw pointer instead of the struct clk pointer so that when
we try to create a per-user struct clk in clk_get_sys() we don't
dereference a junk pointer.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Staticize symbols not exported and not used outside of file.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Replace duplicated const keyword with proper array of const pointers to
const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The array of parent names can be made as array of const pointers to
const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The array of parent names can be made as array of const pointers to
const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add missing static to local (file-scope only) symbols.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add missing static to local (file-scope only) symbols.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds basic clocks for MT8173, including TOPCKGEN, PLLs,
INFRA and PERI clocks.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds basic clocks for MT8135, including TOPCKGEN, PLLs,
INFRA and PERI clocks.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The pericfg and infracfg units also provide reset lines to several
other SoC internal units. This adds a function which can be called
from the pericfg and infracfg initialization functions which will
register the reset controller using reset_controller_register. The
reset controller will provide support for resetting the units
connected to the pericfg and infracfg controller. The units resetted
by this controller can use the standard reset device tree binding
to gain access to the reset lines.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds common clock support for Mediatek SoCs, including plls,
muxes and clock gates.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[sboyd@codeaurora.org: Squelch checkpatch warning in clk-mtk.h]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clk functions and structs declare the parent_name arrays as
'const char **parent_names' which means the parent name strings
are const, but the array itself is not. Use
'const char * const * parent_names' instead which also makes
the array const. This allows us to put the parent_name arrays into
the __initconst section.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[sboyd@codeaurora.org: Squelch 80-character checkpatch warnings]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_io_request_and map returns an error pointer, but the current code assumes
that on error the returned pointer will be NULL.
Obviously, that makes the check completely useless. Change the test to actually
check for the proper error code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Commit ae43b32891 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power
Management support v12") added pm support for the pl330 dma driver but
it makes the clock for the Exynos5420 MDMA0 DMA controller to be gated
during suspend and this in turn makes its parent clock aclk266_g2d to
be gated. But the clock needs to be ungated prior suspend to allow the
system to be suspend and resumed correctly.
Add GATE_BUS_TOP register to the list of registers to be restored when
the system enters into a suspend state so aclk266_g2d will be ungated.
Thanks to Abhilash Kesavan for figuring out that this was the issue.
Fixes: ae43b32 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12")
Cc: stable@vger.kernel.org # 3.19+
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
key/value pairs in a JSON object must be separated by a comma.
After adding the properties "accuracy" and "phase" the JSON output
of /sys/kernel/debug/clk/clk_dump is invalid.
So add the missing commas to fix it.
Fixes: 5279fc402a ("clk: add clk accuracy retrieval support")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
[sboyd@codeaurora.org: Added comment in function]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The gfx3d_clk_src parents configuration is incorrect. Fix it.
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
One of the video codec clock frequencies has incorrect divider
value. Fix it.
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The debugfs clk directory no longer expresses a clk tree. Update
the comments around that apporiately. Also drop comments about
prepare locks needing to be held as we have the proper
annotations with lockdep_assert_held().
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Move the code around so that we don't need to declare function
prototypes at the start of the file. Simplify
clk_core_is_prepared() and clk_core_is_enabled() too to make the
diff easier to read.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This condition can't ever be true because this function is static
and it's always called with a non-NULL pointer.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We don't need to print error messages when allocations fail.
We'll get a nice backtrace in such situations anyway.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These functions are only used in one place. Let's squash them
into their respective callers to save some lines.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
[sboyd@codeaurora.org: Redo commit text, add NULL check in
clk_enable()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
While introducing struct clk_core we tried to minimize the diff
by changing the type of 'clk' variables from struct clk to struct
clk_core without changing the names of the variables. Now that
the split is complete, the code is slightly confusing when it
mixes variables called 'clk' and variables called 'core' that are
of the same type struct clk_core. Let's be consistent and use
'core' everywhere we have a struct clk_core pointer and 'clk'
when we have a struct clk pointer.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch fixes the wrong parent clock of sclk_apollo clock
from 'div_apollo_pll' to 'div_apollo2'.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
CLK_PCLK_MONOTONIC_CNT clock had a wrong register assigned to it.
The correct register is ENABLE_PCLK_MIF_SECURE_MONOTONIC_CNT.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch removes the CONFIG_ARCH_EXYNOS5433 and then use only the
CONFIG_ARCH_EXYNOS for ARM-64bit Exynos5433 SoC.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This includes some
cleanups and removal of code, and the final flip of config dependencies
- Shmobile has several platforms that are going multiplatform, but this
branch also contains a bunch of cleanups that they weren't able to keep
separate in a good way. THere's also a removal of one of their SoCs and the
corresponding boards (sh7372 and mackerel).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVNzfJAAoJEIwa5zzehBx3iRcP/1v9Rw2yk4NpUDaz5EUwhwN6
y5l29gW8jJmVuHWqLUqsgh61dsj5AEEAL7fEEbR8e8848s+RxsehjsGPIxFOkR74
KaKSRlrUgxKcsFN97Jo/WqT3seC83hg6zWQapwNypX33gBtrRLPhM9FEb05asYA8
6x7N29kFeH9M3A6lrabXGWz5tPRZSthwuBSmomHOfgqa5zbgkoaK59j867Yac0q+
Pemh0eJZHC3Pyrmh7ZcVaCaSvr1QO6ructmLopmHAXfls2Fi21wq3IN3641aiitC
G7hhb1/c961MpE3p+0dQyrXs645qIgYv/fDxp72T8YwA7FhjMmIscX/WiITXMlvC
Mg/fDJXqgRkTPWjvVM6xF8TKCSdvqfmErWtHt2dtgvbFWL0ffSeoYF35AF5BODVG
jp8RR6vQ/CHKFao5iJmTpm0ccjnzdS82FEb0PrhG0vY+u6uCsKMim5tn8wUBuBkM
QU2FipNt6STC5ZcCSb+p7r5ihod9rG+BlNL/eXJ+pBHuVnjSgltEaZBP9qIiFjZl
MLRjm7JaEY3LpAR/TVurtSrUnh0zC0RRSzptK4RekmFIwyL+mqq/I1yrksdnVjgf
upj1dZwFRsVtD5PcaU3LyTYCOLSI8L9+b6vVvfFH0Sq4V7TkaBkI/kxnhI2WfkBc
CJ+3vptpyphw6zHAngAN
=Vq4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code changes from Olof Johansson:
"The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This
includes some cleanups and removal of code, and the final flip of
config dependencies
- Shmobile has several platforms that are going multiplatform, but
this branch also contains a bunch of cleanups that they weren't
able to keep separate in a good way. THere's also a removal of one
of their SoCs and the corresponding boards (sh7372 and mackerel)"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: at91/pm: move AT91_MEMCTRL_* to pm.h
ARM: at91/pm: move the standby functions to pm.c
ARM: at91: fix pm_suspend.S compilation when ARMv6 is selected
ARM: at91: add a Kconfig dependency on multi-platform
ARM: at91: drop AT91_TIMER_HZ
ARM: at91: remove hardware.h
ARM: at91: remove SoC headers
ARM: at91: remove useless mach/cpu.h
ARM: at91: remove unused headers
ARM: at91: switch at91_dt_defconfig to multiplatform
ARM: at91: switch to multiplatform
ARM: shmobile: r8a7778: enable multiplatform target
ARM: shmobile: bockw: add sound to DT
ARM: shmobile: r8a7778: add sound to DT
ARM: shmobile: bockw: add devices hooked up to i2c0 to DT
DT: i2c: add trivial binding for OKI ML86V7667 video decoder
ARM: shmobile: r8a7778: common clock framework CPG driver
ARM: shmobile: bockw dts: set extal clock frequency
ARM: shmobile: bockw dts: Move Ethernet node to BSC
ARM: shmobile: r8a73a4: Remove legacy code
...
drivers and updates to existing ones for feature enhancements and bug
fixes. There is more churn than usual in the framework core due to the
change to introduce per-user unique struct clk pointers in 4.0. This
caused several regressions to surface, some of which were sent as fixes
to 4.0. New generic clock drivers were added for GPIO- and PWM-based
clock controllers. Additionally the common clk-divider code recieved
several fixes to the way it rounds rates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2LMr
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.0 are mostly new clock
drivers and updates to existing ones for feature enhancements and bug
fixes.
There is more churn than usual in the framework core due to the change
to introduce per-user unique struct clk pointers in 4.0. This caused
several regressions to surface, some of which were sent as fixes to
4.0. New generic clock drivers were added for GPIO- and PWM-based
clock controllers.
Additionally the common clk-divider code recieved several fixes to the
way it rounds rates"
* tag 'clk-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (91 commits)
clk: check ->determine/round_rate() return value in clk_calc_new_rates
clk: at91: usb: propagate rate modification to the parent clk
clk: samsung: exynos4: Disable ARMCLK down feature on Exynos4210 SoC
clk: don't use __initconst for non-const arrays
clk: at91: change to using endian agnositc IO
clk: clk-gpio-gate: Fix active low
clk: Add PWM clock driver
clk: Add clock driver for mb86s7x
clk: pxa: pxa3xx: add missing os timer clock
clk: tegra: Use the proper parent for plld_dsi
clk: tegra: Use generic tegra_osc_clk_init() on Tegra114
clk: tegra: Model oscillator as clock
clk: tegra: Add peripheral registers for bank Y
clk: tegra: Register the proper number of resets
clk: tegra: Remove needless initializations
clk: tegra: Use consistent indentation
clk: tegra: Various whitespace cleanups
clk: tegra: Enable HDA to HDMI clocks on Tegra124
clk: tegra: Fix a bunch of sparse warnings
clk: tegra: Fix typo tabel -> table
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
Now that the kernel provides DIV_ROUND_CLOSEST_ULL(), drop the internal
implementation and use the kernel one.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
->determine_rate() and ->round_rate() can return the closest rate to the
requested one or an error code.
clk_calc_new_rates is assuming these functions can't return a negative
value, which leads to a undefined behavior when the clk implementation
returns such an error code.
Fix this by returning NULL in case ->determine_rate() or ->round_rate()
returned an error code.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The at91sam9n12 and at91sam9x5 usb clocks do not propagate rate
modification requests to their parents.
This causes a bug when the PLLB is left uninitialized by the bootloader
(PLL multiplier set to 0, or in other words, PLL rate = 0 Hz).
Implement the determinate_rate method and propagate the change rate
request to the parent clk.
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Commit 42773b28e7 ("clk: samsung: exynos4: Enable ARMCLK
down feature") enabled ARMCLK down feature on all Exynos4
SoCs. Unfortunately on Exynos4210 SoC ARMCLK down feature
causes a lockup when ondemand cpufreq governor is used.
Fix it by limiting ARMCLK down feature to Exynos4x12 SoCs.
This patch was tested on:
- Exynos4210 SoC based Trats board
- Exynos4210 SoC based Origen board
- Exynos4412 SoC based Trats2 board
- Exynos4412 SoC based Odroid-U3 board
Cc: Daniel Drake <drake@endlessm.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Fixes: 42773b28e7 ("clk: samsung: exynos4: Enable ARMCLK down feature")
Cc: <stable@vger.kernel.org> # v3.17+
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The statement
static const char *name[];
defines a modifiable array of pointers to constant chars. That is
*name[0] = 'f';
is forbidden, but
name[0] = "f";
is not. So marking an array that is defined as above with __initconst is
wrong. Either an additional const must be added such that the whole
definition reads:
static const char *const name[] __initconst;
or where this is not possible __initdata must be used.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
These are mostly cleanups that I've been carrying in my local tree for
far too long. In addition to those, there are some preparatory patches
for the upcoming Tegra210 support and a patch to enable clocks needed
for HDMI audio support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4zxP
-----END PGP SIGNATURE-----
Merge tag 'clk/for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk/tegra: Changes for v4.1-rc1
These are mostly cleanups that I've been carrying in my local tree for
far too long. In addition to those, there are some preparatory patches
for the upcoming Tegra210 support and a patch to enable clocks needed
for HDMI audio support.
The active low flag in the DT cell is currently ignored.
This occurs because of_get_named_gpio_flags() does not apply the flags
to the underlying struct gpio_desc so the test in clk_register_gpio_gate()
was bogus.
Note that this patch changes the internal kernel API for
clk_register_gpio_gate() but there are currently no other users.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Some board designers, when running out of clock output pads, decide to
(mis)use PWM output pads to provide a clock to external components.
This driver supports this practice by providing an adapter between the
PWM and clock bindings in the device tree. As the PWM bindings specify
the period in the device tree, this is a fixed clock.
Tested-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The CRG11 clock controller is managed by remote f/w.
This driver simply maps Linux CLK ops onto mailbox api.
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Vincent Yang <vincent.yang@socionext.com>
Signed-off-by: Tetsuya Nuriya <nuriya.tetsuya@socionext.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The pxa3xx scheduler relies on the pxa-timer, which requires a clock for
its rate. As the clock handling will be taken over by the clock
framework, add this missing clock.
The miss was discovered by attempting to run a zylonite platform in a
device-tree configuration, with the future patch to shift clocks
handling to clock framework applied.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The current parent, plld_out0, does not exist. The proper name is
pll_d_out0. While at it, rename the plld_dsi clock to pll_d_dsi_out to
be more consistent with other clock names.
Fixes: b270491eb9 ("clk: tegra: Define PLLD_DSI and remove dsia(b)_mux")
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is no reason why Tegra114 cannot use the same generic code to set
up the oscillator, clk_m and pll_ref clocks. The only effective change
that this causes is that the CLK_SET_PARENT_RATE flag is dropped, but
since these clocks are all fixed it is not needed anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the Tegra clock driver simplifies the clock tree somewhat by
taking advantage of the fact that clk_m runs at the same frequency as
the oscillator. While that's true on all currently supported SoCs, it
does not apply to Tegra210 anymore. On Tegra210 clk_m is typically
divided down from the oscillator frequency. To support that setup, add
a separate clock for the oscillator that both clk_m and pll_ref derive
from.
Modify the tegra_osc_clk_init() function to take an additional divider
parameter for clk_m. Existing SoCs always pass in 1, whereas Tegra210
will read the divider from a register in the clock & reset controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has an extra bank of peripheral clock registers. Add it to the
generic peripheral clock code.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The number of resets controls is 32 times the number of peripheral
register banks rather than 32 times the number of clocks. This reduces
(drastically) the number of reset controls registered from 10080 (315
clocks * 32) to 224 (6 peripheral register banks * 32).
This also fixes a potential crash because trying to use any of the
excess reset controls (224-10079) would have caused accesses beyond
the array bounds of the peripheral register banks definition array.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Fixes: 6d5b988e7d ("clk: tegra: implement a reset driver")
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ret variable is often explicitly initialized to 0, but there is no
need to do so in many cases because it will immediately be overwritten
with the return value from a function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some of the .dev_id entries in the devclks table were oddly indented.
Make them consistent with the rest of the table.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the clocks used for HDMI audio played through the HDA controller.
Initialize the codec clock to 48Mhz and the HDA clock to 102MHz per
the TRM.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The second to last parameter of the TEGRA_CLK_PERIPH macro denotes a
table and should therefore users should pass in NULL instead of 0.
Fixes a bunch of sparse warnings like this:
warning: Using plain integer as NULL pointer
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The clock initialization structure is named struct clk_init_table.
Update the kerneldoc comment to use the correct name.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Put NULL test on the result of the previous call instead on one of its
arguments. A simplified version of the semantic match that finds this
problem is as follows (http://coccinelle.lip6.fr/):
// <smpl>
r@
expression *e1;
expression *e2;
identifier f;
statement S1,S2;
@@
e1 = f(...,e2,...);
(
if (e1 == NULL || ...) S1 else S2
|
*if (e2 == NULL || ...) S1 else S2
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When we introduced the parent_map tables, we missed to update
some of the functions where mapping is translated. Fix this.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Support for Qualcomm's clock controllers should be available only
on Qualcomm platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The NAND controller within EBI2 requires EBI2_CLK and
EBI2_ALWAYS_ON_CLK clocks. Create structs for these clocks so
that they can be used by the NAND controller driver. Add an entry
for EBI2_AON_CLK in the gcc-ipq806x DT binding document.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
__initdata updated to __initconst for
static const struct of_device_id ti_clkdm_match_table[]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Register the clock gates for the external audio and ethernet
reference clocks provided by the top-level general control block.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9321/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register the system interface gate clocks provided by the peripheral
general control block. These clocks gate register access for various
peripherals.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9322/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register the clocks generated by the peripheral clock controller.
This includes the clocks for several peripherals, including I2C,
PWM, watchdog, and timer.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9320/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register the clocks generated by the core clock controller.
This includes the 7 PLLs and clocks for the CPU, RPU co-processor,
audio, WiFi, bluetooth, and several other peripherals.
The MIPS and PERIPH_SYS clocks must remain enabled at all times.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9317/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a driver for the integer (GF40LP_LAINT) and fractional (GF40LP_FRAC)
PLLs present on Pistachio.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9316/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add clock controller for CMU ISP clock domain on Exynos3250,
providing clocks for FIMC-IS subsystem.
[b.michalska: use samsung_cmu_register_one to register
the provider; updated DT binding documentation]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
[s.nawrocki: added __init attribute which was missing in function
exynos3250_cmu_platform_init() in function, which has been]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This patch add CLKOUT driver support for Exynos3250 SoC.
Exynos3250 SoC PMU_DEBUG is the same with Exynos4's PMU_DEBUG
including CLKOUT mux. So we can use the exynos4's clkout init
function for Exynos3250 without the need to add new function.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Replace doubled const in the arrays of clock names with proper const
pointer to const data. This fixes the warnings:
drivers/clk/clk-si5351.c:71:25: warning: duplicate const
drivers/clk/clk-si5351.c:74:25: warning: duplicate const
drivers/clk/clk-si5351.c:77:25: warning: duplicate const
drivers/clk/clk-si5351.c:80:25: warning: duplicate const
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/qcom/clk-pll.c:74:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>