Now that legacy iSeries is gone, this is no longer used.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So many defines for such a little file. Most of them can go.
Also remove the single entry changelog, we have git for that.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The RAS error interrupt is no longer used but we may as well
mirror the changes we made to the EPOW interrupt.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
IBM bit 2 in the rtas event-scan and check-exception calls is
marked reserved in the PAPR, so remove it from our RAS code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have rtas_get_sensor so we may as well use it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have code to take environmental and power warning (EPOW)
interrupts but it simply prints a terse error message:
EPOW <0x6240040000000b8 0x0 0x0>
which tells us nothing about what happened. Even worse, if we
don't correctly respond to the interrupt we may get terminated
by firmware.
Add code to printk some useful information when we get EPOW events.
We want to make it clear that we have an error, that it was
reported by firmware and that the RTAS error log will have more
detailed information. eg:
Ambient temperature too high reported by firmware.
Check RTAS error log for details
Depending on the error encountered, we now issue an immediate or
an orderly power down.
Move initialization of the EPOW interrupt earlier in boot since we
want to respond to them as early as possible.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The IO event interrupt code has a function that finds specific
sections in an RTAS error log. We want to use it in the EPOW
code so make it global.
Rename things to make it less cryptic:
find_xelog_section() -> get_pseries_errorlog()
struct pseries_elog_section -> struct pseries_errorlog
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the existing PHBs are retrieved from the FDT (Flat
Device Tree) based on the name of FDT node. Specificly, those
FDT nodes whose names have prefix "pci" are regarded as PHBs.
That's inappropriate because some PCI bridges possibilly have
names leading with "pci". It caused EEH is enabled on same
PCI devices for towice.
The patch fixes the above issue. Besides, the PHBs are expected
to be figured out from FDT before enable EEH on them. Therefore,
it's resonable to retrieve the PHBs from the global linked list
traced by variable "hose_list" insteading poking them from FDT.
For the EEH implementation on pSeries platform, RTAS is critical
because all low-level functions are implemented based on RTAS.
Therefore, we should make sure "/rtas" OF node is available and
ready before to enable EEH core. However, it actually introduced
duplicate since the previous pSeries platform dependent initialization
function already do the check. Besides, we want to make eeh core
platform independent, so RTAS related staff should be removed there.
The patch removes the duplicate check on "/rtas" OF node for eeh
core.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch removes the eeh information from pci_dn since the eeh
device (struct eeh_dev) already contained those information and
the copy in pci_dn is no longer used except for the pseries iommu
mapping code, which we change to retrieve the PE address from eeh
device instead.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Originally, the PCI sensitive OF node is tracing the eeh device
through struct device_node->edev. However, it was regarded as
bad idea.
The patch removes struct device_node->edev and uses PCI_DN to
trace the corresponding eeh device according to BenH's comments.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a set of macros that can be used to declare
kernel parameters to be parsed _before_ initcalls at a chosen
level are executed. We rename the now-unused "flags" field of
struct kernel_param as the level. It's signed, for when we
use this for early params as well, in future.
Linker macro collating init calls had to be modified in order
to add additional symbols between levels that are later used
by the init code to split the calls into blocks.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
"[RFC - PATCH 0/7] consolidation of BUG support code."
https://lkml.org/lkml/2012/1/26/525
--
The changes shown here are to unify linux's BUG support under
the one <linux/bug.h> file. Due to historical reasons, we have
some BUG code in bug.h and some in kernel.h -- i.e. the support for
BUILD_BUG in linux/kernel.h predates the addition of linux/bug.h,
but old code in kernel.h wasn't moved to bug.h at that time. As
a band-aid, kernel.h was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions.
Here is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.]
Ugh - very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and
hence relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2.
But to ensure that git history for bisect doesn't get needless
build failures introduced, the commits have been reorderd to fix
the problem areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PYQT
-----END PGP SIGNATURE-----
Merge tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/bug.h> cleanup from Paul Gortmaker:
"The changes shown here are to unify linux's BUG support under the one
<linux/bug.h> file. Due to historical reasons, we have some BUG code
in bug.h and some in kernel.h -- i.e. the support for BUILD_BUG in
linux/kernel.h predates the addition of linux/bug.h, but old code in
kernel.h wasn't moved to bug.h at that time. As a band-aid, kernel.h
was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions. Here
is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.] Ugh -
very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and hence
relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2. But
to ensure that git history for bisect doesn't get needless build
failures introduced, the commits have been reorderd to fix the problem
areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414"
Fix up conflicts (new radeon file, reiserfs header cleanups) as per Paul
and linux-next.
* tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
kernel.h: doesn't explicitly use bug.h, so don't include it.
bug: consolidate BUILD_BUG_ON with other bug code
BUG: headers with BUG/BUG_ON etc. need linux/bug.h
bug.h: add include of it to various implicit C users
lib: fix implicit users of kernel.h for TAINT_WARN
spinlock: macroize assert_spin_locked to avoid bug.h dependency
x86: relocate get/set debugreg fcns to include/asm/debugreg.
Merge second batch of patches from Andrew Morton:
- various misc things
- core kernel changes to prctl, exit, exec, init, etc.
- kernel/watchdog.c updates
- get_maintainer
- MAINTAINERS
- the backlight driver queue
- core bitops code cleanups
- the led driver queue
- some core prio_tree work
- checkpatch udpates
- largeish crc32 update
- a new poll() feature for the v4l guys
- the rtc driver queue
- fatfs
- ptrace
- signals
- kmod/usermodehelper updates
- coredump
- procfs updates
* emailed from Andrew Morton <akpm@linux-foundation.org>: (141 commits)
seq_file: add seq_set_overflow(), seq_overflow()
proc-ns: use d_set_d_op() API to set dentry ops in proc_ns_instantiate().
procfs: speed up /proc/pid/stat, statm
procfs: add num_to_str() to speed up /proc/stat
proc: speed up /proc/stat handling
fs/proc/kcore.c: make get_sparsemem_vmemmap_info() static
coredump: add VM_NODUMP, MADV_NODUMP, MADV_CLEAR_NODUMP
coredump: remove VM_ALWAYSDUMP flag
kmod: make __request_module() killable
kmod: introduce call_modprobe() helper
usermodehelper: ____call_usermodehelper() doesn't need do_exit()
usermodehelper: kill umh_wait, renumber UMH_* constants
usermodehelper: implement UMH_KILLABLE
usermodehelper: introduce umh_complete(sub_info)
usermodehelper: use UMH_WAIT_PROC consistently
signal: zap_pid_ns_processes: s/SEND_SIG_NOINFO/SEND_SIG_FORCED/
signal: oom_kill_task: use SEND_SIG_FORCED instead of force_sig()
signal: cosmetic, s/from_ancestor_ns/force/ in prepare_signal() paths
signal: give SEND_SIG_FORCED more power to beat SIGNAL_UNKILLABLE
Hexagon: use set_current_blocked() and block_sigmask()
...
The motivation for this patchset was that I was looking at a way for a
qemu-kvm process, to exclude the guest memory from its core dump, which
can be quite large. There are already a number of filter flags in
/proc/<pid>/coredump_filter, however, these allow one to specify 'types'
of kernel memory, not specific address ranges (which is needed in this
case).
Since there are no more vma flags available, the first patch eliminates
the need for the 'VM_ALWAYSDUMP' flag. The flag is used internally by
the kernel to mark vdso and vsyscall pages. However, it is simple
enough to check if a vma covers a vdso or vsyscall page without the need
for this flag.
The second patch then replaces the 'VM_ALWAYSDUMP' flag with a new
'VM_NODUMP' flag, which can be set by userspace using new madvise flags:
'MADV_DONTDUMP', and unset via 'MADV_DODUMP'. The core dump filters
continue to work the same as before unless 'MADV_DONTDUMP' is set on the
region.
The qemu code which implements this features is at:
http://people.redhat.com/~jbaron/qemu-dump/qemu-dump.patch
In my testing the qemu core dump shrunk from 383MB -> 13MB with this
patch.
I also believe that the 'MADV_DONTDUMP' flag might be useful for
security sensitive apps, which might want to select which areas are
dumped.
This patch:
The VM_ALWAYSDUMP flag is currently used by the coredump code to
indicate that a vma is part of a vsyscall or vdso section. However, we
can determine if a vma is in one these sections by checking it against
the gate_vma and checking for a non-NULL return value from
arch_vma_name(). Thus, freeing a valuable vma bit.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
Pull powerpc merge from Benjamin Herrenschmidt:
"Here's the powerpc batch for this merge window. It is going to be a
bit more nasty than usual as in touching things outside of
arch/powerpc mostly due to the big iSeriesectomy :-) We finally got
rid of the bugger (legacy iSeries support) which was a PITA to
maintain and that nobody really used anymore.
Here are some of the highlights:
- Legacy iSeries is gone. Thanks Stephen ! There's still some bits
and pieces remaining if you do a grep -ir series arch/powerpc but
they are harmless and will be removed in the next few weeks
hopefully.
- The 'fadump' functionality (Firmware Assisted Dump) replaces the
previous (equivalent) "pHyp assisted dump"... it's a rewrite of a
mechanism to get the hypervisor to do crash dumps on pSeries, the
new implementation hopefully being much more reliable. Thanks
Mahesh Salgaonkar.
- The "EEH" code (pSeries PCI error handling & recovery) got a big
spring cleaning, motivated by the need to be able to implement a
new backend for it on top of some new different type of firwmare.
The work isn't complete yet, but a good chunk of the cleanups is
there. Note that this adds a field to struct device_node which is
not very nice and which Grant objects to. I will have a patch soon
that moves that to a powerpc private data structure (hopefully
before rc1) and we'll improve things further later on (hopefully
getting rid of the need for that pointer completely). Thanks Gavin
Shan.
- I dug into our exception & interrupt handling code to improve the
way we do lazy interrupt handling (and make it work properly with
"edge" triggered interrupt sources), and while at it found & fixed
a wagon of issues in those areas, including adding support for page
fault retry & fatal signals on page faults.
- Your usual random batch of small fixes & updates, including a bunch
of new embedded boards, both Freescale and APM based ones, etc..."
I fixed up some conflicts with the generalized irq-domain changes from
Grant Likely, hopefully correctly.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (141 commits)
powerpc/ps3: Do not adjust the wrapper load address
powerpc: Remove the rest of the legacy iSeries include files
powerpc: Remove the remaining CONFIG_PPC_ISERIES pieces
init: Remove CONFIG_PPC_ISERIES
powerpc: Remove FW_FEATURE ISERIES from arch code
tty/hvc_vio: FW_FEATURE_ISERIES is no longer selectable
powerpc/spufs: Fix double unlocks
powerpc/5200: convert mpc5200 to use of_platform_populate()
powerpc/mpc5200: add options to mpc5200_defconfig
powerpc/mpc52xx: add a4m072 board support
powerpc/mpc5200: update mpc5200_defconfig to fit for charon board
Documentation/powerpc/mpc52xx.txt: Checkpatch cleanup
powerpc/44x: Add additional device support for APM821xx SoC and Bluestone board
powerpc/44x: Add support PCI-E for APM821xx SoC and Bluestone board
MAINTAINERS: Update PowerPC 4xx tree
powerpc/44x: The bug fixed support for APM821xx SoC and Bluestone board
powerpc: document the FSL MPIC message register binding
powerpc: add support for MPIC message register API
powerpc/fsl: Added aliased MSIIR register address to MSI node in dts
powerpc/85xx: mpc8548cds - add 36-bit dts
...
Pull vfs pile 1 from Al Viro:
"This is _not_ all; in particular, Miklos' and Jan's stuff is not there
yet."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (64 commits)
ext4: initialization of ext4_li_mtx needs to be done earlier
debugfs-related mode_t whack-a-mole
hfsplus: add an ioctl to bless files
hfsplus: change finder_info to u32
hfsplus: initialise userflags
qnx4: new helper - try_extent()
qnx4: get rid of qnx4_bread/qnx4_getblk
take removal of PF_FORKNOEXEC to flush_old_exec()
trim includes in inode.c
um: uml_dup_mmap() relies on ->mmap_sem being held, but activate_mm() doesn't hold it
um: embed ->stub_pages[] into mmu_context
gadgetfs: list_for_each_safe() misuse
ocfs2: fix leaks on failure exits in module_init
ecryptfs: make register_filesystem() the last potential failure exit
ntfs: forgets to unregister sysctls on register_filesystem() failure
logfs: missing cleanup on register_filesystem() failure
jfs: mising cleanup on register_filesystem() failure
make configfs_pin_fs() return root dentry on success
configfs: configfs_create_dir() has parent dentry in dentry->d_parent
configfs: sanitize configfs_create()
...
This branch contains a minor documentation addition, a utility
function for parsing string properties needed by some of the new ARM
platforms, disables dynamic DT code that isn't used anywhere but on a
few PPC machines, and exports DT node compatible data to userspace via
UEVENT properties. Nothing earth shattering here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kK/B
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull core device tree changes for Linux v3.4 from Grant Likely:
"This branch contains a minor documentation addition, a utility
function for parsing string properties needed by some of the new ARM
platforms, disables dynamic DT code that isn't used anywhere but on a
few PPC machines, and exports DT node compatible data to userspace via
UEVENT properties. Nothing earth shattering here."
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux-2.6:
of: Only compile OF_DYNAMIC on PowerPC pseries and iseries
arm/dts: OMAP3: Add omap3evm and am335xevm support
drivercore: Output common devicetree information in uevent
of: Add of_property_match_string() to find index into a string list
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ruGA
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull irq_domain support for all architectures from Grant Likely:
"Generialize powerpc's irq_host as irq_domain
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
dt: fix twl4030 for non-dt compile on x86
mfd: twl-core: Add IRQ_DOMAIN dependency
devicetree: Add empty of_platform_populate() for !CONFIG_OF_ADDRESS (sparc)
irq_domain: Centralize definition of irq_dispose_mapping()
irq_domain/mips: Allow irq_domain on MIPS
irq_domain/x86: Convert x86 (embedded) to use common irq_domain
ppc-6xx: fix build failure in flipper-pic.c and hlwd-pic.c
irq_domain/microblaze: Convert microblaze to use irq_domains
irq_domain/powerpc: Replace custom xlate functions with library functions
irq_domain/powerpc: constify irq_domain_ops
irq_domain/c6x: Use library of xlate functions
irq_domain/c6x: constify irq_domain structures
irq_domain/c6x: Convert c6x to use generic irq_domain support.
irq_domain: constify irq_domain_ops
irq_domain: Create common xlate functions that device drivers can use
irq_domain: Remove irq_domain_add_simple()
irq_domain: Remove 'new' irq_domain in favour of the ppc one
mfd: twl-core.c: Fix the number of interrupts managed by twl4030
of/address: add empty static inlines for !CONFIG_OF
irq_domain: Add support for base irq and hwirq in legacy mappings
...
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
Commit c55aef0e5b "powerpc/boot: Change the load address for the wrapper
to fit the kernel" adjusted the laod address if the uncompressed kernel
was too large. Ps3 does not compress the kernel and uses a different
linker script, so do not adjust the load address in that case.
fixes this build error:
powerpc64-linux-ld: section .text loaded at [0000000000e00000,0000000000e0721b] overlaps section .kernel:dtb loaded at [0000000000e00000,0000000000e0066f]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
since they are not referenced any more.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is no longer selectable, so just remove all the dependent code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
spufs return path has a bug where it could end up trying to
unlock an inode mutex twice. Fix it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
of_platform_populate() also handles nodes at the root of the tree,
which is wanted for things like describing the sound complex. This
patch converts mpc5200 support to use of_platform_populate() instead
of of_platform_bus_probe().
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add the following options to the mpc5200_defconfig, needed
for the a4m072 board support:
CONFIG_AMD_PHY=y
CONFIG_GPIO_SYSFS=y
CONFIG_SENSORS_LM87=m
CONFIG_RTC_DRV_PCF8563=m
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add DTS file for a4m072 board and add its name to the list
of the supported boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Grant Likely <grant.likely@secretlab.ca>
cc: devicetree-discuss@ozlabs.org
cc: Wolfgang Denk <wd@denx.de>
cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
We believe there's no reason to prevent reallocation on PA Semi, so
revert to the default of "allow reallocation if necessary."
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: linuxppc-dev@lists.ozlabs.org
Tested-by: Olof Johansson <olof@lixom.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Normal PCI enumeration via PCI config space uses __pci_read_base(), where
the PCI core applies any bus-to-resource offset. But powerpc doesn't use
that path when enumerating via the device tree.
In 6c5705fec6, I converted powerpc to use the PCI core bus-to-resource
conversion, but I missed these powerpc-specific paths. Some powerpc
platforms fail to boot ("Cannot allocate resource region," "device not
available," etc.) between that commit and this one.
This adds the corresponding bus-to-resource conversion in the paths that
read BAR values from the OF device tree.
CC: Anton Blanchard <anton@samba.org>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make sure we compute CPU addresses (resource start/end) the same way both
when we set up the I/O aperture (hose->io_resource) and when we use
pcibios_bus_to_resource() to convert BAR values into resources.
This fixes a build failure ("cast from pointer to integer of different
size" in configs where resource_size_t is 64 bits but pointers are 32 bits)
I introduced in 6c5705fec6.
Acked-By: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Pull scheduler changes for v3.4 from Ingo Molnar
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
printk: Make it compile with !CONFIG_PRINTK
sched/x86: Fix overflow in cyc2ns_offset
sched: Fix nohz load accounting -- again!
sched: Update yield() docs
printk/sched: Introduce special printk_sched() for those awkward moments
sched/nohz: Correctly initialize 'next_balance' in 'nohz' idle balancer
sched: Cleanup cpu_active madness
sched: Fix load-balance wreckage
sched: Clean up parameter passing of proc_sched_autogroup_set_nice()
sched: Ditch per cgroup task lists for load-balancing
sched: Rename load-balancing fields
sched: Move load-balancing arguments into helper struct
sched/rt: Do not submit new work when PI-blocked
sched/rt: Prevent idle task boosting
sched/wait: Add __wake_up_all_locked() API
sched/rt: Document scheduler related skip-resched-check sites
sched/rt: Use schedule_preempt_disabled()
sched/rt: Add schedule_preempt_disabled()
sched/rt: Do not throttle when PI boosting
sched/rt: Keep period timer ticking when rt throttling is active
...
[swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Add following options to mpc5200_defconfig:
- CONFIG_MTD_PLATRAM=y
(selects CONFIG_MTD_RAM, so this is removed)
- CONFIG_FIXED_PHY=y
- CONFIG_SENSORS_LM80=y
- CONFIG_FB_FOREIGN_ENDIAN=y
- CONFIG_FB_SM501=m
- CONFIG_RTC_DRV_DS1374=y
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Grant Likely <grant.likely@secretlab.ca>
cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch extends PCI-E driver to support PCI-E for APM821xx SoC on Bluestone
board.
Signed-off-by: Vinh Nguyen Huu Tuong <vhtnguyen@apm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
This patch consists of:
- Fix the pvr mask for checking pvr in cputable.c
- Fix the cpu name as consistent with cpu name is describled in dts file
Signed-off-by: Vinh Nguyen Huu Tuong <vhtnguyen@apm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Some MPIC implementations contain one or more blocks of message registers
that are used to send messages between cores via IPIs. A simple API has
been added to access (get/put, read, write, etc ...) these message registers.
The available message registers are initially discovered via nodes in the
device tree. A separate commit contains a binding for the message register
nodes.
Signed-off-by: Meador Inge <meador_inge@mentor.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MSIIR register for each MSI bank is aliased to a different
address. The MSI node reg property was updated to contain this
address:
e.g. reg = <0x41600 0x200 0x44140 4>;
The first region contains the address and length of the MSI
register set and the second region contains the address of
the aliased MSIIR register at 0x44140.
Signed-off-by: Diana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Create mpc8548cds_36b.dts. Support 36-bit mode.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Create mpc8548cds.dtsi
* Move lbc, soc and pci0 nodes to mpc8548cds_32b.dtsi
* Change cuImage.mpc8548cds to cuImage.mpc8548cds_32b
* Rename mpc8548cds.dts to mpc8548cds_32b.dts
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove FPGA(CADMUS) macros in code. Move it to dts.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correct ethernet1 and add ethernet2 and ethernet3.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable RapidIO and add rapidio and rmu nodes to dts.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is a PCI bridge(Tsi310) between the MPC8548 and a VIA
southbridge chip.
The bootloader sets the PCI bridge to open a window from 0x0000
to 0x1fff on the PCI I/O space. But the kernel can't set the I/O
resource. In the routine pci_read_bridge_io(), if the base which
is read from PCI_IO_BASE is equal to zero, the routine don't set
the I/O resource of the child bus.
To allow the legacy I/O space on the VIA southbridge to be accessed,
use the fixup to fix the PCI I/O space of the PCI bridge.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc85xx_rdb and mpc85xx_mds have commom define of signal multiplex for qe, so
they need to go in common header, the patch abstract them to fsl_guts.h
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the "select PHYS_64BIT" from the Kconfig entry for the P1022DS,
so that large physical address support is a selectable option for non-CoreNet
reference boards.
The option is enabled in mpc85xx_[smp_]defconfig so that the default is
unchanged. However, now it can be deselected.
The P1022DS had this option defined because the default device tree for
this board uses 36-bit addresses. This had the side-effect of forcing
this option on for all boards that use mpc85xx_[smp_]defconfig. Some
users may want to disable this feature to create an optimized configuration
for boards with <= 2GB of RAM.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix the compatible string of sec 4.0 to match with CAAM driver according
to Documentation/devicetree/bindings/crypto/fsl-sec4.txt
Signed-off-by: Liu Shuo <shuo.liu@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl_85xx_l2ctlr.o and fsl_85xx_cache_sram.o are built only
if CONFIG_FSL_85XX_CACHE_SRAM is defined. The driver that
qualifies and wants to make use of the CACHE SRAM's exported
API (i.e. a freescale net driver) should (be able to) select
this config option.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CC arch/powerpc/sysdev/fsl_85xx_l2ctlr.o
arch/powerpc/sysdev/fsl_85xx_l2ctlr.c:209:13: error: 'THIS_MODULE' undeclared here (not in a function)
arch/powerpc/sysdev/fsl_85xx_l2ctlr.c:229:20: error: expected declaration specifiers or '...' before string constant
cc1: warnings being treated as errors
arch/powerpc/sysdev/fsl_85xx_l2ctlr.c:229:1: error: data definition has no type or storage class
arch/powerpc/sysdev/fsl_85xx_l2ctlr.c:229:1: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
arch/powerpc/sysdev/fsl_85xx_l2ctlr.c:229:20: error: function declaration isn't a prototype
arch/powerpc/sysdev/fsl_85xx_l2ctlr.c:230:16: error: expected declaration specifiers or '...' before string constant
arch/powerpc/sysdev/fsl_85xx_l2ctlr.c:230:1: error: data definition has no type or storage class
arch/powerpc/sysdev/fsl_85xx_l2ctlr.c:230:1: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
arch/powerpc/sysdev/fsl_85xx_l2ctlr.c:230:16: error: function declaration isn't a prototype
make[1]: *** [arch/powerpc/sysdev/fsl_85xx_l2ctlr.o] Error 1
...
CC arch/powerpc/sysdev/fsl_85xx_cache_sram.o
cc1: warnings being treated as errors
arch/powerpc/sysdev/fsl_85xx_cache_sram.c:69:1: error: data definition has no type or storage class
arch/powerpc/sysdev/fsl_85xx_cache_sram.c:69:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/powerpc/sysdev/fsl_85xx_cache_sram.c:69:1: error: parameter names (without types) in function declaration
arch/powerpc/sysdev/fsl_85xx_cache_sram.c:80:1: error: data definition has no type or storage class
arch/powerpc/sysdev/fsl_85xx_cache_sram.c:80:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/powerpc/sysdev/fsl_85xx_cache_sram.c:80:1: error: parameter names (without types) in function declaration
make[1]: *** [arch/powerpc/sysdev/fsl_85xx_cache_sram.o] Error 1
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc836x_mds platform has been broken since the commit
6fe3264945
"netdev/phy: Use mdiobus_read() so that proper locks are taken"
which caused the fsl_pq_mdio TBI autoprobe to oops. The oops
was "fixed" in commit 28d8ea2d56
"fsl_pq_mdio: Clean up tbi address configuration"
by simply removing the the autoscan code, and making tbi nodes
mandatory. Some of the newer reference platforms were updated
to have tbi nodes in 220669495b
"powerpc: Add TBI PHY node to first MDIO bus"
but the older mpc836x didn't get one and hence was just failing
with -EBUSY as follows:
fsl-pq_mdio: probe of e0102120.mdio failed with error -16
...
net eth0: Could not attach to PHY
eth0: Cannot initialize PHY, aborting.
Add a TBI node and use the 1st free address for it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When the P1022's DIU video controller is active, the pixis must be accessed
in "indirect" mode, which uses localbus chip select addresses.
Switching between the DVI and LVDS monitor ports is handled by the pixis,
so that switching needs to be done via indirect mode.
This has the side-effect of no longer requiring U-Boot to enable the DIU.
Now Linux can enable the DIU all by itself.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020
processor.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the GE PIC drivers to allow these to be used by non-86xx boards.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The GE GPIO driver provides basic support (set direction, read/write state)
for the GPIO provided on some GE single board computers. This patch moves
the driver from the 86xx specific platform directrory to the GPIO subsystem
so that it can be used on non-86xx boards.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds the GE_FPGA configuration option. This is being carried
out as ground work to allow the PIC and GPIO drivers to be move from the
powerpc 86xx platform directory to more general locations to allow them to
be used on non-86xx boards and to reduce churn when further boards using
these drivers are added.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020RDB-PC Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
10 16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using VitesseTM VSC7385 L2 switch
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p1020utm-pc has the similar feature as the p1020rdb.
Therefore, p1020utm-pc use the same platform file as the p1/p2 rdb board.
Overview of P1020UTM-PC platform:
- DDR3 1GB
- NOR flash 32MB
- I2C EEPROM 256Kb
- eTSEC1 (RGMII PHY Atheros AR8021)
- eTSEC2 (SGMII PHY Vitesse VSC8221)
- eTSEC3 (RGMII PHY Atheros AR8021)
- SDHC
- 2 USB ports
- PCIe (Lane1 to dual SATA controller)
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p1020mbg-pc has the similar feature as the p1020rdb.
Therefore, p1020mbg-pc use the same platform file as the p1/p2 rdb board.
Overview of P1020MBG-PC platform:
- DDR3 2GB
- NOR flash 64MB
- I2C EEPROM 256Kb
- eTSEC1 (RGMII PHY) connected to VSC7385 L2 switch
- eTSEC2 (SGMII PHY)
- eTSEC3 (RGMII PHY)
- SDHC
- 2 USB ports
- 4 TDM ports
- PCIe (Lane1 to dual SATA controller)
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NOR flash, need to be disabled.
This also means that the localbus is not a 'simple-bus' any more, so remove
that string from the compatible node.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Create a 32-bit address space version of p1022ds.dts. To avoid confusion,
p1022ds.dts is renamed to p1022ds_36b.dts. We also create p1022ds.dtsi
to store some common nodes.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The properties indicates that the hardware supports waking up via magic
packet.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix typo introduced by "powerpc: Add TBI PHY node to first MDIO bus"
from Andy Fleming.
It's device_type rather than device-type, which causes the mdio probe to
fail thus making all gianfar ethernet interfaces unusable.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is here most likely since the FSL bsp. Back in the FSL bsp it was
set to 50Mhz and working. However the driver divided the SoC freq. only
by 2. According to the TRM the platform clock (which the manual refers
in its formula) is the system clock divided by two. So in the end it has
to divide by 4 and this is what the fsl-spi driver in tree is doing.
Since then the flash is not wokring I guess. After chaning the freq from
50Mhz to 40Mhz like others do then I can access the flash.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is not at 0xffa00000. According to current u-boot source the NAND
controller is always at 0xff800000 and it is either at CS0 or CS1
depending on NAND or NAND+NOR mode. In 36bit mode it is shifted to
0xfff800000 but it has always an eight there and never an A.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the file "arch/powerpc/sysdev/fsl_rmu.c", there will be some compile
errors while using the corenet64_smp_defconfig:
.../fsl_rmu.c:315: error: cast from pointer to integer of different size
.../fsl_rmu.c:320: error: cast to pointer from integer of different size
.../fsl_rmu.c:320: error: cast to pointer from integer of different size
.../fsl_rmu.c:320: error: cast to pointer from integer of different size
.../fsl_rmu.c:330: error: cast to pointer from integer of different size
.../fsl_rmu.c:332: error: cast to pointer from integer of different size
.../fsl_rmu.c:339: error: cast to pointer from integer of different size
.../fsl_rmu.c:340: error: cast to pointer from integer of different size
.../fsl_rmu.c:341: error: cast to pointer from integer of different size
.../fsl_rmu.c:348: error: cast to pointer from integer of different size
.../fsl_rmu.c:348: error: cast to pointer from integer of different size
.../fsl_rmu.c:348: error: cast to pointer from integer of different size
.../fsl_rmu.c:659: error: cast from pointer to integer of different size
.../fsl_rmu.c:659: error: format '%8.8x' expects type 'unsigned int',
but argument 5 has type 'size_t'
.../fsl_rmu.c:985: error: cast from pointer to integer of different size
.../fsl_rmu.c:997: error: cast to pointer from integer of different size
Rewrote the corresponding code with the support of 64bit building.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the file "arch/powerpc/sysdev/fsl_rio.c", there will be some relocation
errors while using the corenet64_smp_defconfig:
WARNING: modpost: Found 6 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
GEN .version
CHK include/generated/compile.h
UPD include/generated/compile.h
CC init/version.o
LD init/built-in.o
LD .tmp_vmlinux1
arch/powerpc/sysdev/built-in.o:(__ex_table+0x0):
relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3208
arch/powerpc/sysdev/built-in.o:(__ex_table+0x2):
relocation truncated to fit: R_PPC64_ADDR16 against `.fixup'
arch/powerpc/sysdev/built-in.o:(__ex_table+0x4):
relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3230
arch/powerpc/sysdev/built-in.o:(__ex_table+0x6):
relocation truncated to fit: R_PPC64_ADDR16 against `.fixup'+c
arch/powerpc/sysdev/built-in.o:(__ex_table+0x8):
relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3250
arch/powerpc/sysdev/built-in.o:(__ex_table+0xa):
relocation truncated to fit: R_PPC64_ADDR16 against `.fixup'+18
Rewrote the corresponding code with the support of 64bit building.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1025RDB Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using AtherosTM AR8021
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add usb controller version info for the following:
MPC8536, P1010, P1020, P1021, P1022, P1023, P2020, P2041,
P3041, P3060, P5020
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2020RDB-PC Board shares the same design(PCB) as P102x RDB style platforms.
The difference between this platform and the already existing P2020RDB
is mainly with respect to DDR. The P2020RDB-PC has a DDR3 memory.
The P2020RDB-PC also has a CPLD device connected to local bus.
The main differences from the P102x RDB-PC is 64-bit DDR and SYSCLK of
100Mhz.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1021RDB-PC Overview
-----------------
1Gbyte DDR3 (on board DDR)
16Mbyte NOR flash
32Mbyte eSLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
Real-time clock on I2C bus
SD/MMC connector to interface with the SD memory card
PCIex
- x1 PCIe slot or x1 PCIe to dual SATA controller
- x1 mini-PCIe slot
USB 2.0
- ULPI PHY interface: SMSC USB3300 USB PHY and Genesys Logic’s GL850A
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
eTSEC1: Connected to RGMII PHY VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xu Jiucheng <B37781@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
in commit 7230c56441
"powerpc: Rework lazy-interrupt handling"
I introduced a regression, accidentally calling irq tracing twice
and not properly restoring a clobbered register (r7) later used
for writing to the MSR.
This caused lockups when booting on a G5 with lockdep enabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When using the "compat" APIs, architectures will generally want to
be able to make direct syscalls to msgsnd(), shmctl(), etc., and
in the kernel we would want them to be handled directly by
compat_sys_xxx() functions, as is true for other compat syscalls.
However, for historical reasons, several of the existing compat IPC
syscalls do not do this. semctl() expects a pointer to the fourth
argument, instead of the fourth argument itself. msgsnd(), msgrcv()
and shmat() expect arguments in different order.
This change adds an ARCH_WANT_OLD_COMPAT_IPC config option that can be
set to preserve this behavior for ports that use it (x86, sparc, powerpc,
s390, and mips). No actual semantics are changed for those architectures,
and there is only a minimal amount of code refactoring in ipc/compat.c.
Newer architectures like tile (and perhaps future architectures such
as arm64 and unicore64) should not select this option, and thus can
avoid having any IPC-specific code at all in their architecture-specific
compat layer. In the same vein, if this option is not selected, IPC_64
mode is assumed, since that's what the <asm-generic> headers expect.
The workaround code in "tile" for msgsnd() and msgrcv() is removed
with this change; it also fixes the bug that shmat() and semctl() were
not being properly handled.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The registers that describe size supported by TLB are different on MMU
v2 as well as we support power of two page sizes. For now we continue
to assume that FSL variable size array supports all page sizes up to the
maximum one reported in TLB1PS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The SERIAL_8250_EXTENDED option just enables access to other
less regularly used options, like SERIAL_8250_SHARE_IRQ.
Select it to get rid of this warning when selecting the child
option living underneath it.
warning: (FSL_SOC_BOOKE && SERIAL_8250_RM9K) selects
SERIAL_8250_SHARE_IRQ which has unmet direct dependencies
(HAS_IOMEM && SERIAL_8250_EXTENDED)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current implementation of lazy interrupts handling has some
issues that this tries to address.
We don't do the various workarounds we need to do when re-enabling
interrupts in some cases such as when returning from an interrupt
and thus we may still lose or get delayed decrementer or doorbell
interrupts.
The current scheme also makes it much harder to handle the external
"edge" interrupts provided by some BookE processors when using the
EPR facility (External Proxy) and the Freescale Hypervisor.
Additionally, we tend to keep interrupts hard disabled in a number
of cases, such as decrementer interrupts, external interrupts, or
when a masked decrementer interrupt is pending. This is sub-optimal.
This is an attempt at fixing it all in one go by reworking the way
we do the lazy interrupt disabling from the ground up.
The base idea is to replace the "hard_enabled" field with a
"irq_happened" field in which we store a bit mask of what interrupt
occurred while soft-disabled.
When re-enabling, either via arch_local_irq_restore() or when returning
from an interrupt, we can now decide what to do by testing bits in that
field.
We then implement replaying of the missed interrupts either by
re-using the existing exception frame (in exception exit case) or via
the creation of a new one from an assembly trampoline (in the
arch_local_irq_enable case).
This removes the need to play with the decrementer to try to create
fake interrupts, among others.
In addition, this adds a few refinements:
- We no longer hard disable decrementer interrupts that occur
while soft-disabled. We now simply bump the decrementer back to max
(on BookS) or leave it stopped (on BookE) and continue with hard interrupts
enabled, which means that we'll potentially get better sample quality from
performance monitor interrupts.
- Timer, decrementer and doorbell interrupts now hard-enable
shortly after removing the source of the interrupt, which means
they no longer run entirely hard disabled. Again, this will improve
perf sample quality.
- On Book3E 64-bit, we now make the performance monitor interrupt
act as an NMI like Book3S (the necessary C code for that to work
appear to already be present in the FSL perf code, notably calling
nmi_enter instead of irq_enter). (This also fixes a bug where BookE
perfmon interrupts could clobber r14 ... oops)
- We could make "masked" decrementer interrupts act as NMIs when doing
timer-based perf sampling to improve the sample quality.
Signed-off-by-yet: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
v2:
- Add hard-enable to decrementer, timer and doorbells
- Fix CR clobber in masked irq handling on BookE
- Make embedded perf interrupt act as an NMI
- Add a PACA_HAPPENED_EE_EDGE for use by FSL if they want
to retrigger an interrupt without preventing hard-enable
v3:
- Fix or vs. ori bug on Book3E
- Fix enabling of interrupts for some exceptions on Book3E
v4:
- Fix resend of doorbells on return from interrupt on Book3E
v5:
- Rebased on top of my latest series, which involves some significant
rework of some aspects of the patch.
v6:
- 32-bit compile fix
- more compile fixes with various .config combos
- factor out the asm code to soft-disable interrupts
- remove the C wrapper around preempt_schedule_irq
v7:
- Fix a bug with hard irq state tracking on native power7
With the original EEH implementation, the access to config space of
the corresponding PCI device is done by RTAS sensitive function. That
depends on pci_dn heavily. That would limit EEH extension to other
platforms like powernv because other platforms might have different
ways to access PCI config space.
The patch splits those functions used to access PCI config space
and implement them in platform related EEH component. It would be
helpful to support EEH on multiple platforms simutaneously in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the original EEH implementation, the EEH global statistics
are maintained by individual global variables. That makes the
code a little hard to maintain.
The patch introduces extra struct eeh_stats for the EEH global
statistics so that it can be maintained in collective fashion.
It's the rework on the corresponding v5 patch. According to
the comments from David Laight, the EEH global statistics have
been changed for a litte bit so that they have fixed-type of
"u64". Also, the format used to print them has been changed to
"%llu" based on David's suggestion. Also, the output format of
EEH global statistics should be kept as intacted according to
Michael's suggestion that there might be tools parsing them.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pci_dn has been replaced with eeh_dev. In order to comply with
the rule, the EEH platform implementation on pSeries should also
be adjusted for a little bit so that it will depend on eeh_dev instead
of pci_dn.
The patch replaces pci_dn with eeh_dev. The corresponding information
will be retrieved from eeh_dev instead of pci_dn.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The original EEH implementation is heavily depending on struct pci_dn.
We have to put EEH related information to pci_dn. Actually, we could
split struct pci_dn so that the EEH sensitive information to form an
individual struct, then EEH looks more independent.
The patch replaces pci_dn with eeh_dev for EEH aux components like
event and driver. Also, the eeh_event struct has been adjusted for
a little bit since eeh_dev has linked the associated FDT (Flat Device
Tree) node and PCI device. It's not necessary for eeh_event struct to
trace FDT node and PCI device. We can just simply to trace eeh_dev in
eeh_event.
The patch also renames function pcid_name() to eeh_pcid_name(), which
should be missed in the previous patch where the EEH aux components
have been cleaned up.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell