Given that the bulk of the Kconfig file is enclosed in "if USB_ATM",
remove the unnecessary dependencies.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1084b) fixes the way uhci-hcd handles polling and
remote wakeups for its root hubs. When remote wakeup is disabled,
neither interrupts nor polling should be enabled during a root-hub
suspend. Likewise, if interrupts are enabled during suspend then
polling isn't needed.
Furthermore the EGSM (Enter Global Suspend Mode) bit shouldn't be set
in the Command register unless remote wakeup is enabled. Apparently
some controllers will issue a remote-wakeup interrupt whenever EGSM
is on, even if Resume-Detect interrupts are supposedly disabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch (as1086) works around a bogus "uninitialized variable"
warning generated by some versions of GCC.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds HCD support for the Cypress c67x00 family of devices.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch add the core driver for the c67x00 USB OTG controller. The core
driver is responsible for the platform bus binding and creating either
USB HCD or USB Gadget instances for each of the serial interface engines
on the chip.
This driver does not directly implement the HCD or gadget behaviours; it
just controls access to the chip.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the low level support code for the Cypress c67x00 family of
OTG controllers. The low level code is responsible for register access and
implements the software protocol for communicating with the 16bit
microcontroller inside the c67x00 device.
Communication is done over the HPI interface (16bit SRAM-like parallel bus).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch fixes a [probable] copy & paste mistake in
airprime.c. Instead of unlocking an acquired mutex, the actual
code tries to lock it again.
Signed-off-by: Leonardo Chiquitto <lchiquitto@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/unusual_devs.h lists the address
linux-usb-devel@lists.sourceforge.net for patches to that file. This
address results in a bounce and a pointer to vger. This patch updates
the address in the header file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This device descriptor was added by the recent USB Link Power Management (LPM)
ECN. It indicates whether the USB device supports LPM.
This descriptor is grouped under a Binary Device Object Store (BOS) descriptor.
Update the BOS comments to indicate any USB device (not just wireless USB
devices) can implement BOS descriptors.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When I used ohci-sm501, hcd_alloc_coherent() in map_urb_for_dma() is not
called, because usb_sg_init() always sets URB_NO_TRANSFER_DMA_MAP.
dmesg (CONFIG_USB_STORAGE_DEBUG enabled):
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code -75; transferred 0/36
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x2
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initialize timer earlier so if an error occurs allocating USB request
or buffer request (zero_bind) Gadget Zero will not hang trying to
delete an uninitialized timer (zero_unbind).
Signed-off-by: David Lopo <lopo.david@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor updates to "Gadget Zero".
- Primarily these are whitespace updates to address the fact that since
this was written, Documentation/CodingStyle was changed to disapprove
of parts of the original coding style.
- Update a few comments that weren't quite correct, notably mentioning
the "autoresume" module parameter.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch from <Aurel.Thomi@ruag.com>, this makes the
CDC-ACM support in the serial gadget handle the SET_LINE_CODING
and SET_CONTROL_LINE_STATE requests ... which should improve
interop with at least MS-Windows "usbser.sys" if not some other
ACM host drivers.
It also adds a few REVISIT comments where this code plays a bit
loose with the CDC ACM spec. If this were used to hook up to a
real RS232 or modem link, those places would need a bit of work.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds pxa27x udc driver to support USB peripherals on pxa27x chips.
The driver is compatible with: Gadget Zero, the File Storage
gadget, and the Ethernet gadget (only in CDC subset mode).
The driver can't properly support multiple interfaces, because
of hardware bugs without possible workaround. That means no
RNDIS support from g_ether, and no CDC ACM support in g_serial.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
FIX_CAPACITY is all that's needed.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The test for an mos7840_set_uart_reg() error return value only works when
status is signed. propagate its error value.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: SL Baur <steve@xemacs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup to the "usbtest" driver, mostly to resolve a regression:
all the important diagnostics were at KERN_DEBUG, so that when the
"#define DEBUG" was removed from the top of that file it stopped
providing diagnostics. Fix by using KERN_ERROR. Also:
- Stop using the legacy dbg() calls
- Simplify the internal debug macros
- Correct some test descriptions:
* Test #10 subcase 7 should *always* stall
* Test #10 subcase 8 *may* stall
- Diagnostic about control queue test failures is more informative
- Fix some whitespace "bugs"
And add a warning about the rude interaction between usbfs ioctl()
and khubd during device disconnect ... don't unplug a device under
test, that will wedge.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I hoped to continue to ignore this problem or use libusual, but these
days it's simpler to work around than to deal with it. Let's attempt to
use bad residue devices and hope that upper level integrity checks catch
any problems (e.g. please use sha1sum on your backups).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wodim says:
"close track/session scsi sendcmd: cmd timeout after 5.000 (480) s"
This happened because we ignored the supplied timeout and used 5s.
It's not completely correct to apply a timeout meant for the complete
command to any single URB, but we don't have many URBs per command, so
this is simple and works.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1088) adds an unusual_devs entry for Samsung's YP-U3.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global onetouch_release_input() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If USB storage is built-in but input subsystem is made modular then
OneTouch button functionality can not be selected.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver has been written from scratch and supports the ISP1760. ISP1761
might (should) work as well but the OTG isn't supported. Also ISO packets are
not. However, it works on my little PowerPC board.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for variable-length, extended, and vendor specific
CDBs to scsi-ml. It is now possible for initiators and ULD's
to issue these types of commands. LLDs need not change much.
All they need is to raise the .max_cmd_len to the longest command
they support (see iscsi patch).
- clean-up some code paths that did not expect commands to be
larger than 16, and change cmd_len members' type to short as
char is not enough.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of git://www.linux-m32r.org/git/takata/linux-2.6_dev:
m32r: cleanup: drop .data.idt section in vmlinux.lds script
m32r: use KBUILD_DEFCONFIG
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: make Launcher see device status updates
lguest: remove bogus NULL cpu check
lguest: avoid using NR_CPUS as a bounds check.
virtio: add virtio disk geometry feature
virtio: explicit advertisement of driver features
virtio: change config to guest endian.
virtio: finer-grained features for virtio_net
virtio: wean net driver off NETDEV_TX_BUSY
virtio-blk: fix remove oops
virtio: fix scatterlist sizing in net driver.
virtio: de-structify virtio_block status byte
virtio: export more headers to userspace
virtio: fix sparse return void-valued expression warnings
virtio: fix tx_ stats in virtio_net
virtio: ignore corrupted virtqueues rather than spinning.
- struct scsi_cmnd had a 16 bytes command buffer of its own.
This is an unnecessary duplication and copy of request's
cmd. It is probably left overs from the time that scsi_cmnd
could function without a request attached. So clean that up.
- Once above is done, few places, apart from scsi-ml, needed
adjustments due to changing the data type of scsi_cmnd->cmnd.
- Lots of drivers still use MAX_COMMAND_SIZE. So I have left
that #define but equate it to BLK_MAX_CDB. The way I see it
and is reflected in the patch below is.
MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB
as per the SCSI standard and is not related
to the implementation.
BLK_MAX_CDB. - The allocated space at the request level
- I have audit all ISA drivers and made sure none use ->cmnd in a DMA
Operation. Same audit was done by Andi Kleen.
(*)fixed-length here means commands that their size can be determined
by their opcode and the CDB does not carry a length specifier, (unlike
the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly
true and the SCSI standard also defines extended commands and
vendor specific commands that can be bigger than 16 bytes. The kernel
will support these using the same infrastructure used for VARLEN CDB's.
So in effect MAX_COMMAND_SIZE means the maximum size command
scsi-ml supports without specifying a cmd_len by ULD's
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This enables bsg to handle the request length larger than BLK_MAX_CDB
(mainly for the variable length CDB format).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On Apr 21, 2008, at 8:42 PM, Yinghai Lu wrote:
> bisected to:
>
> commit e6990c6448
> Author: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
> Date: Mon Apr 14 14:20:16 2008 -0400
>
> [SCSI] aacraid: Fix down_interruptible() to check the return value
The return value for down_interruptible was incorrectly checked!
updated patch enclosed.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The PROM library function prom_meminit() builds a table,
prom_phys_avail[], just so that probe_memory() in
arch/sparc/mm/fault.c can copy it into sp_banks[].
Just have prom_meminit() fill in the sp_banks[] array directly, and
remove duplicated sort() function.
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in arch/sparc/prom/memory.c computes three tables, the list
of total memory, the list of available memory (total minus what
firmware is using), and the list of firmware taken memory.
Only the available memory list is even used.
Therefore, kill those unused tables and make prom_meminfo() return
just the available memory list.
Signed-off-by: David S. Miller <davem@davemloft.net>
The change I put into copy_thread() just papered over the real
problem.
When we are looking to see if we should do a syscall restart, when
deliverying a signal, we should only interpret the syscall return
value as an error if the carry condition code(s) are set.
Otherwise it's a success return.
Also, sigreturn paths should do a pt_regs_clear_trap_type().
It turns out that doing a syscall restart when returning from a fork()
does and should happen, from time to time. Even if copy_thread()
returns success, copy_process() can still unwind and signal
-ERESTARTNOINTR in the parent.
Signed-off-by: David S. Miller <davem@davemloft.net>
It just creates confusion, errors, and bugs.
For one thing, this can cause dup sysfs or procfs nodes to get
created:
[ 1.198015] proc_dir_entry '00.0' already registered
[ 1.198036] Call Trace:
[ 1.198052] [00000000004f2534] create_proc_entry+0x7c/0x98
[ 1.198092] [00000000005719e4] pci_proc_attach_device+0xa4/0xd4
[ 1.198126] [00000000007d991c] pci_proc_init+0x64/0x88
[ 1.198158] [00000000007c62a4] kernel_init+0x190/0x330
[ 1.198183] [0000000000426cf8] kernel_thread+0x38/0x48
[ 1.198210] [00000000006a0d90] rest_init+0x18/0x5c
Signed-off-by: David S. Miller <davem@davemloft.net>
This brings us closer to Real Life, where we'd examine the device
features once it's set the DRIVER_OK status bit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
NR_CPUS (being a host number) is an arbitrary limit for the Guest.
Using the array size directly (which currently happes to be NR_CPUS)
is more futureproof.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rather than faking up some geometry, allow the backend to push the disk
geometry via virtio pci config option. Keep the old geo code around for
compatibility.
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (modified to single struct)
A recent proposed feature addition to the virtio block driver revealed
some flaws in the API: in particular, we assume that feature
negotiation is complete once a driver's probe function returns.
There is nothing in the API to require this, however, and even I
didn't notice when it was violated.
So instead, we require the driver to specify what features it supports
in a table, we can then move the feature negotiation into the virtio
core. The intersection of device and driver features are presented in
a new 'features' bitmap in the struct virtio_device.
Note that this highlights the difference between Linux unsigned-long
bitmaps where each unsigned long is in native endian, and a
straight-forward little-endian array of bytes.
Drivers can still remove feature bits in their probe routine if they
really have to.
API changes:
- dev->config->feature() no longer gets and acks a feature.
- drivers should advertise their features in the 'feature_table' field
- use virtio_has_feature() for extra sanity when checking feature bits
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
