Commit 7a9bc9b81a ("ipv4: Elide fib_validate_source() completely when possible.")
introduced a short-circuit to avoid calling fib_validate_source when not
needed. That change took rp_filter into account, but not accept_local.
This resulted in a change of behaviour: with rp_filter and accept_local
off, incoming packets with a local address in the source field should be
dropped.
Here is how to reproduce the change pre/post 7a9bc9b81a commit:
-configure the same IPv4 address on hosts A and B.
-try to send an ARP request from B to A.
-The ARP request will be dropped before that commit, but accepted and answered
after that commit.
This adds a check for ACCEPT_LOCAL, to maintain full
fib validation in case it is 0. We also leave __fib_validate_source() earlier
when possible, based on the same check as fib_validate_source(), once the
accept_local stuff is verified.
Cc: Gregory Detal <gregory.detal@uclouvain.be>
Cc: Christoph Paasch <christoph.paasch@uclouvain.be>
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Sébastien Barré <sebastien.barre@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of the function usb_endpoint_num.
The Coccinelle semantic patch that makes these changes is as follows:
@@ struct usb_endpoint_descriptor *epd; @@
- (epd->bEndpointAddress & \(USB_ENDPOINT_NUMBER_MASK\|0x0f\))
+ usb_endpoint_num(epd)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of the function usb_endpoint_num.
The Coccinelle semantic patch that makes these changes is as follows:
@@ struct usb_endpoint_descriptor *epd; @@
- (epd->bEndpointAddress & \(USB_ENDPOINT_NUMBER_MASK\|0x0f\))
+ usb_endpoint_num(epd)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the buffer is too small for a packet from VMBus, a bigger buffer will be
allocated in netvsc_channel_cb() and retry reading the packet from VMBus.
Increasing this buffer size will reduce the retry overhead.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test for definedness of the macro which is actually defined (the
change is hard to see: it is s/SSS/SSA/).
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SCTP, selection of active (T.ACT) and retransmission (T.RET)
transports is being done whenever transport control operations
(UP, DOWN, PF, ...) are engaged through sctp_assoc_control_transport().
Commits 4c47af4d5e ("net: sctp: rework multihoming retransmission
path selection to rfc4960") and a7288c4dd5 ("net: sctp: improve
sctp_select_active_and_retran_path selection") have both improved
it towards a more fine-grained and optimal path selection.
Currently, the selection algorithm for T.ACT and T.RET is as follows:
1) Elect the two most recently used ACTIVE transports T1, T2 for
T.ACT, T.RET, where T.ACT<-T1 and T1 is most recently used
2) In case primary path T.PRI not in {T1, T2} but ACTIVE, set
T.ACT<-T.PRI and T.RET<-T1
3) If only T1 is ACTIVE from the set, set T.ACT<-T1 and T.RET<-T1
4) If none is ACTIVE, set T.ACT<-best(T.PRI, T.RET, T3) where
T3 is the most recently used (if avail) in PF, set T.RET<-T.PRI
Prior to above commits, 4) was simply a camp on T.ACT<-T.PRI and
T.RET<-T.PRI, ignoring possible paths in PF. Camping on T.PRI is
still slightly suboptimal as it can lead to the following scenario:
Setup:
<A> <B>
T1: p1p1 (10.0.10.10) <==> .'`) <==> p1p1 (10.0.10.12) <= T.PRI
T2: p1p2 (10.0.10.20) <==> (_ . ) <==> p1p2 (10.0.10.22)
net.sctp.rto_min = 1000
net.sctp.path_max_retrans = 2
net.sctp.pf_retrans = 0
net.sctp.hb_interval = 1000
T.PRI is permanently down, T2 is put briefly into PF state (e.g. due to
link flapping). Here, the first time transmission is sent over PF path
T2 as it's the only non-INACTIVE path, but the retransmitted data-chunks
are sent over the INACTIVE path T1 (T.PRI), which is not good.
After the patch, it's choosing better transports in both cases by
modifying step 4):
4) If none is ACTIVE, set T.ACT_new<-best(T.ACT_old, T3) where T3 is
the most recently used (if avail) in PF, set T.RET<-T.ACT_new
This will still select a best possible path in PF if available (which
can also include T.PRI/T.RET), and set both T.ACT/T.RET to it.
In case sctp_assoc_control_transport() *just* put T.ACT_old into INACTIVE
as it transitioned from ACTIVE->PF->INACTIVE and stays in INACTIVE just
for a very short while before going back ACTIVE, it will guarantee that
this path will be reselected for T.ACT/T.RET since T3 (PF) is not
available.
Previously, this was not possible, as we would only select between T.PRI
and T.RET, and a possible T3 would be NULL due to the fact that we have
just transitioned T3 in sctp_assoc_control_transport() from PF->INACTIVE
and would select a suboptimal path when T.PRI/T.RET have worse properties.
In the case that T.ACT_old permanently went to INACTIVE during this
transition and there's no PF path available, plus T.PRI and T.RET are
INACTIVE as well, we would now camp on T.ACT_old, but if everything is
being INACTIVE there's really not much we can do except hoping for a
successful HB to bring one of the transports back up again and, thus
cause a new selection through sctp_assoc_control_transport().
Now both tests work fine:
Case 1:
1. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
2. T1 S(ACTIVE) T.ACT, T.RET
T2 S(PF)
3. T1 S(ACTIVE) T.ACT, T.RET
T2 S(INACTIVE)
5. T1 S(PF) T.ACT, T.RET
T2 S(INACTIVE)
[ 5.1 T1 S(INACTIVE) T.ACT, T.RET
T2 S(INACTIVE) ]
6. T1 S(ACTIVE) T.ACT, T.RET
T2 S(INACTIVE)
7. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
Case 2:
1. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
2. T1 S(PF)
T2 S(ACTIVE) T.ACT, T.RET
3. T1 S(INACTIVE)
T2 S(ACTIVE) T.ACT, T.RET
5. T1 S(INACTIVE)
T2 S(PF) T.ACT, T.RET
[ 5.1 T1 S(INACTIVE)
T2 S(INACTIVE) T.ACT, T.RET ]
6. T1 S(INACTIVE)
T2 S(ACTIVE) T.ACT, T.RET
7. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both transports are the same, we don't have to go down that
road only to realize that we will return the very same transport.
We are guaranteed that curr is always non-NULL. Therefore, just
short-circuit this special case.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing defines _ASM_GENERIC_INT_L64_H, it is a weird way to check for
64 bit longs, and u64 should be printed using %llx anyway.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.
Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
A NULL pointer dereference is possible for the argument ring->buf_pool
which is passed to xgene_enet_free_desc_ring(), as ring could be NULL.
And now since NULL pointers are being checked for before the calls to
xgene_enet_free_desc_ring(), might as well take advantage of them and
not call the function if the argument would be NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there are multiple vlan headers present in a received frame, the first
one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the
skb beyond the VLAN TPID may be still non-linear, including the inner TCI
and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it
does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is
executed, __pop_vlan_tci pulls the next vlan header into vlan_tci.
This leads to two things:
1. Part of the resulting ethernet header is in the non-linear part of the
skb. When eth_type_trans is called later as the result of
OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci
is in fact accessing random data when it reads past the TPID.
2. network_header points into the ethernet header instead of behind it.
mac_len is set to a wrong value (10), too.
Reported-by: Yulong Pei <ypei@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.
FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.
To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.
i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.
To avoid the issue, we need to check ptp clock status before ptp timer count access.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This small set of fixes addresses a few issues introduced during the
merge window, including:
- Fix typo in I-cache detection that was causing us to treat all
I-caches as aliasing
- Hook up memfd_create and getrandom syscalls for native and compat
- Revert a temporary hack for defconfig builds in -next (the audit
tree changes didn't make it in this merge window)
- A couple of UEFI fixes for TEXT_OFFSET fuzzing and /memreserve/
- A simple sparsemem fix for 48-bit physical addressing
- Small defconfig updates to get autotesters working with X-gene
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BqdY
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"This small set of fixes addresses a few issues introduced during the
merge window, including:
- fix typo in I-cache detection that was causing us to treat all
I-caches as aliasing
- hook up memfd_create and getrandom syscalls for native and compat
- revert a temporary hack for defconfig builds in -next (the audit
tree changes didn't make it in this merge window)
- a couple of UEFI fixes for TEXT_OFFSET fuzzing and /memreserve/
- a simple sparsemem fix for 48-bit physical addressing
- small defconfig updates to get autotesters working with X-gene"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "arm64: Do not invoke audit_syscall_* functions if !CONFIG_AUDIT_SYSCALL"
arm64: mm: update max pa bits to 48
arm64: ignore DT memreserve entries when booting in UEFI mode
arm64: configs: Enable X-Gene SATA and ethernet in defconfig
arm64: align randomized TEXT_OFFSET on 4 kB boundary
asm-generic: add memfd_create system call to unistd.h
arm64: compat: wire up memfd_create and getrandom syscalls for aarch32
arm64: fix typo in I-cache policy detection
The fixes include:
* A patch to fix a crash in the VT-d driver when devices with a
driver attached are hot-unplugged
* A patch for the AMD IOMMU driver to fix a crash with device
assignment of 32 bit PCI devices to KVM guests
* Fix for a copy&paste error in generic IOMMU code. Now the
right function pointer is checked before calling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=KWBo
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"The fixes include:
- fix a crash in the VT-d driver when devices with a driver attached
are hot-unplugged
- fix a AMD IOMMU driver crash with device assignment of 32 bit PCI
devices to KVM guests
- fix for a copy&paste error in generic IOMMU code. Now the right
function pointer is checked before calling"
* tag 'iommu-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/core: Check for the right function pointer in iommu_map()
iommu/amd: Fix cleanup_domain for mass device removal
iommu/vt-d: Defer domain removal if device is assigned to a driver
Description of problem:
The NIC card is not reporting back to the driver the transmitted skbs,
so they get stuck in the TX ring causing issues with reference
counters in other kernel components.
Developed a new Automatic Egress Queue Update firmware facility to slowly tick
through Egress Queues and send back any outstanding CIDX Updates which are
laying around.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlP1svIACgkQjTAFq1RaXHPV6wCfWtoj6987iIwKYSuz9q8nUB03
YtsAn0o3r44apjJT6uwEIfFR1M6NCuQK
=5Bee
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.17-20140821' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-08-21
The first patch is from Mirza Krak, it fixes the initialization of the hardware
in the sja1000 driver. The next patch is contributed by Dan Carpenter, it fixes
the error handling in the c_can's probe function. Then there are two patches
for the flexcan driver, one by Alexander Stein, which fixes the resetting of
the bus error interrupt mask, the other one by Sebastian Andrzej Siewior which
adds an additional error state transition message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible race condition when we unregister the PCI Driver and then
flush/destroy the global "workq". This could lead to situations where there
are tasks on the Work Queue with references to now deleted adapter data
structures. Instead, have per-adapter Work Queues which were instantiated and
torn down in init_one() and remove_one(), respectively.
v2: Remove unnecessary call to flush_workqueue() before destroy_workqueue()
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the transport has always been in state SCTP_UNCONFIRMED, it
therefore wasn't active before and hasn't been used before, and it
always has been, so it is unnecessary to bug the user with a
notification.
Reported-by: Deepak Khandelwal <khandelwal.deepak.1987@gmail.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Suggested-by: Michael Tuexen <tuexen@fh-muenster.de>
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 91ebb929b6 ("bnx2x: Add support for Multi-Function UNDI") [which was
later supposedly fixed by de682941ee ("bnx2x: Fix UNDI driver unload")]
introduced a bug in which in some [yet-to-be-determined] scenarios the
alternative flushing mechanism which was to guarantee the Rx buffers are
empty before resetting them during device probe will fail.
If this happens, when device will be loaded once more a fatal attention will
occur; Since this most likely happens in boot from SAN scenarios, the machine
will fail to load.
Notice this may occur not only in the 'Multi-Function' scenario but in the
regular scenario as well, i.e., this introduced a regression in the driver's
ability to perform boot from SAN.
The patch reverts the mechanism and applies the old scheme to multi-function
devices as well as to single-function devices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh says:
====================
qlcnic: Bug fixes
This series fixes some bugs related to endianess.
Please apply this series to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware binary file is in little endian. On big-endian architecture, while
writing this binary FW file to adapters memory, writel() swaps the data resulting into
corruption of FW image. So, swap the data before writing into adapters memory.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware dump template header is read from adapter using
readl() which swaps the data. So, adjust structure
element on the boundary of 32bit dword.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Application expects flash data in little endian, but driver reads/writes
flash data using readl()/writel() APIs which swaps data on big endian machine.
So, swap the data after reading from and before writing to flash memory.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan is the original author of the driver. This change was discussed
with the 802.15.4 subsystem maintainer, Alexander Aring.
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, macvlan code restricts multicast and unicast
filter setting only to passthru devices. As a result,
if a guest using macvtap wants to receive multicast
traffic, it has to set IFF_ALLMULTI or IFF_PROMISC.
This patch makes it possible to use the fdb interface
to add multicast addresses to the filter thus allowing
a guest to receive only targeted multicast traffic.
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
af_packet can currently overwrite kernel memory by out of bound
accesses, because it assumed a [new] block can always hold one frame.
This is not generally the case, even if most existing tools do it right.
This patch clamps too long frames as API permits, and issue a one time
error on syslog.
[ 394.357639] tpacket_rcv: packet too big, clamped from 5042 to 3966. macoff=82
In this example, packet header tp_snaplen was set to 3966,
and tp_len was set to 5042 (skb->len)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: f6fb8f100b ("af-packet: TPACKET_V3 flexible buffer implementation.")
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LECS response contains the MTU that should be used. Correctly
synchronize with other layers when updating.
Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull libata fixes from Tejun Heo:
"Nothing drastic but pushing out early due to build breakage in the new
tegra platform.
Additionally:
- M550 tagged trim blacklist pattern is widened so that it matches
the new 1TB model
- three controller specific fixes"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: widen Crucial M550 blacklist matching
pata_scc: propagate return value of scc_wait_after_reset
ata: ahci_tegra: Change include to fix compilation
pata_samsung_cf: change ret type to signed
ahci_xgene: Removing NCQ support from the APM X-Gene SoC AHCI SATA Host Controller driver.
Pull HID fixes from Jiri Kosina:
- fixes for a couple potential memory corruption problems (the HW would
have to be manufactured to be deliberately evil to trigger those)
found by Ben Hawkes
- fix for potential infinite loop when using sysfs interface of
logitech driver, from Simon Wood
- a couple more simple driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix a couple of off-by-ones
HID: logitech: perform bounds checking on device_id early enough
HID: logitech: fix bounds checking on LED report size
HID: logitech: Prevent possibility of infinite loop when using /sys interface
HID: rmi: print an error if F11 is not found instead of stopping the device
HID: hid-sensor-hub: use devm_ functions consistently
HID: huion: Use allocated buffer for DMA
HID: huion: Fail on parameter retrieval errors
A bunch of ASoC fixes with a few HD-audio fixes in this pull request.
All fairly small, boring and device-specific fixes, in addition to
MAINTAINERS update for better reviewing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJT9b8uAAoJEGwxgFQ9KSmkOZUP/RmB+4/vscB3z+exCFldIG3R
gHOn4ER/JRWoObVVST3VabU5T5v88/gC2/12uYHFJQdDIwaMQytdVMDzhi6v8Uyf
MFh24DcHQ7dRsedCCrUeoy2DZ42G+HhPH+SRGinkFUZ0RJjnCgqvyYw1p6KZD29K
AuB07FbgmThqRVyoZoMh3K7zm8d/ZeZU59SkyGi2U8dhCfgZyrsYZ1jHd/fGuwq4
XgJIJvHWZoniFnnxoVW/r9wutbF5JSf/FbwRI7ptZT0Rj/u+PcgDPmrhYPINFkt2
IrIt/ZnGadKZuiK9p+aSSIUPWluVjyChCwskkWfKtg+5N4FOFed48HjZNw5TVsdc
deJjao7dtyqxugMcA2E6VkWqTprFRhRbauT0WU7KX54HBrnng3792YGLJqqqggCE
bAP5crrT1wMjk7qXPLouk0TvcXbSkCYQ53Ip+QITGNkLUiN0tj8cgbsfPjDU4GvH
T9tz0I5thLkKp4xP3xSEphQdaLdmG0zGiBcoOH/6jByUxvQdiQimo7a1YEuxtFN2
sIGbrpM8k9ypfJaOpqoh6FtHRL9Y41W1guY4TqUm+QZbLw9KQn1QRe9HQF5M6kU+
vsIoVR8UGTudaLG/AIg+YFEbSsTcTlCNHw1iXYxmqj5pP5J+N0N/aNIFYeObWkcO
8O9/WAwBUdH0cVdXoWze
=x5gm
-----END PGP SIGNATURE-----
Merge tag 'sound-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bunch of ASoC fixes with a few HD-audio fixes in this pull request.
All fairly small, boring and device-specific fixes, in addition to
MAINTAINERS update for better reviewing"
* tag 'sound-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/hdmi - apply Valleyview fix-ups to Cherryview display codec
ALSA: hda/hdmi - set depop_delay for haswell plus
ALSA: hda - restore the gpio led after resume
ALSA: hda/realtek - Avoid setting wrong COEF on ALC269 & co
ASoC: pxa-ssp: drop SNDRV_PCM_FMTBIT_S24_LE
ASoC: fsl-esai: Revert .xlate_tdm_slot_mask() support
ASoC: mcasp: Fix implicit BLCK divider setting
ASoC: arizona: Fix TDM slot length handling in arizona_hw_params
ASoC: pcm512x: Correct Digital Playback control names
ASoC: dapm: Fix uninitialized variable in snd_soc_dapm_get_enum_double()
ASoC: Intel: Restore Baytrail ADSP streams only when ADSP was in reset
ASoC: Intel: Wait Baytrail ADSP boot at resume_early stage
ASoC: Intel: Merge Baytrail ADSP suspend_noirq into suspend_late
MAINTAINERS: Add i.MX maintainers and paths to Freescale ASoC entry
ASoC: Intel: Update Baytrail ADSP firmware name
Pull i2c fixes from Wolfram Sang:
"Here is the fixup for the 'lowlight' of my last pull request. I2C is
not selected anymore by I2C_ACPI. Instead, the code in question now
depends on I2C=y.
Also, Mika has agreed to support me and be the maintainer for I2C-ACPI
related patches. Finally, a new-ID-patch came along last week"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer for ACPI parts of I2C
i2c: i801: Add PCI ID for Intel Braswell
i2c: rework kernel config I2C_ACPI
There are a few very theoretical off-by-one bugs in report descriptor size
checking when performing a pre-parsing fixup. Fix those.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
device_index is a char type and the size of paired_dj_deivces is 7
elements, therefore proper bounds checking has to be applied to
device_index before it is used.
We are currently performing the bounds checking in
logi_dj_recv_add_djhid_device(), which is too late, as malicious device
could send REPORT_TYPE_NOTIF_DEVICE_UNPAIRED early enough and trigger the
problem in one of the report forwarding functions called from
logi_dj_raw_event().
Fix this by performing the check at the earliest possible ocasion in
logi_dj_raw_event().
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The check on report size for REPORT_TYPE_LEDS in logi_dj_ll_raw_request()
is wrong; the current check doesn't make any sense -- the report allocated
by HID core in hid_hw_raw_request() can be much larger than
DJREPORT_SHORT_LENGTH, and currently logi_dj_ll_raw_request() doesn't
handle this properly at all.
Fix the check by actually trimming down the report size properly if it is
too large.
Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Once the CAN-bus is open and a packet is sent, the controller switches
into the PASSIVE state. Once the BUS is closed again it goes the back
err-warning. The TX error counter goes 0 -> 0x80 -> 0x7f.
This patch makes sure that the user learns about this state chang
(CAN_STATE_ERROR_WARNING => CAN_STATE_ERROR_PASSIVE)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Matthias Klein <matthias.klein@optimeas.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case we don't have FLEXCAN_HAS_BROKEN_ERR_STATE and the user set
CAN_CTRLMODE_BERR_REPORTING once it can not be unset again until reboot.
So in case neither hardware nor user wants the error interrupt disable
the bit.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
devm_ioremap() returns NULL on error, not an ERR_PTR().
Fixes: 33cf756569 ('can: c_can_platform: Fix raminit, use devm_ioremap() instead of devm_ioremap_resource()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When sja1000 is not compiled as module the SJA1000 chip is only
initialized during device registration on kernel boot. Should the chip
get a hardware reset there is no way to reinitialize it without re-
booting the Linux kernel.
This patch adds a check in sja1000_start if the chip is initialized, if
not we initialize it.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull cifs fixes from Steve French:
"Most important fixes in this set include three SMB3 fixes for stable
(including fix for possible kernel oops), and a workaround to allow
writes to Mac servers (only cifs dialect, not more current SMB2.1,
worked to Mac servers). Also fallocate support added, and lease fix
from Jeff"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
[SMB3] Enable fallocate -z support for SMB3 mounts
enable fallocate punch hole ("fallocate -p") for SMB3
Incorrect error returned on setting file compressed on SMB2
CIFS: Fix wrong directory attributes after rename
CIFS: Fix SMB2 readdir error handling
[CIFS] Possible null ptr deref in SMB2_tcon
[CIFS] Workaround MacOS server problem with SMB2.1 write response
cifs: handle lease F_UNLCK requests properly
Cleanup sparse file support by creating worker function for it
Add sparse file support to SMB2/SMB3 mounts
Add missing definitions for CIFS File System Attributes
cifs: remove unused function cifs_oplock_break_wait
Pull filesystem fixes from Jan Kara:
"udf, isofs, and ext3 bug fixes"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext3: Count internal journal as bsddf overhead in ext3_statfs
isofs: Fix unbounded recursion when processing relocated directories
udf: avoid unneeded up_write when fail to add entry in ->symlink
Pull x86 platform driver revert from Matthew Garrett:
"This clearly shouldn't have been merged. No excuse on my part"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
Revert "platform/x86/toshiba-apci.c possible bad if test?"
(one has a CVE), and fixing some problems introduced during the merge window
(the CMA bug came in via Andrew, the x86 ones via yours truly).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=lhLd
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Reverting a 3.16 patch, fixing two bugs in device assignment (one has
a CVE), and fixing some problems introduced during the merge window
(the CMA bug came in via Andrew, the x86 ones via yours truly)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
virt/kvm/assigned-dev.c: Set 'dev->irq_source_id' to '-1' after free it
Revert "KVM: x86: Increase the number of fixed MTRR regs to 10"
KVM: x86: do not check CS.DPL against RPL during task switch
KVM: x86: Avoid emulating instructions on #UD mistakenly
PC, KVM, CMA: Fix regression caused by wrong get_order() use
kvm: iommu: fix the third parameter of kvm_iommu_put_pages (CVE-2014-3601)
These are the two bug fixes I mentioned in the final merge window pull. One
is a reversed logic check in the device busy tests which can cause a nasty
hang and another crash seen in the new SCSI pool support if the use count ever
goes to zero.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT85zGAAoJEDeqqVYsXL0Mnw4IAJ7BP+4nUlP7Oib8JfPu4Df2
b6dv3YEGe6th4awrHqUnATusjQLIybk/rgRKb6P50o1iX2VI+rs1mAm9esw9NalS
8aKzDMAv9pTRsRvAhe3AnIVGGCYAekV4AZWmsXQPCKqcsQZSZKAnIerLBf0lBemR
X3+1VhYtbB9z4o0Gpv4E5mR/7CqIouDpe5QGRKRY2+/Yyp2El6Vzwqr9XMLyOvmY
Y9WaIhM1UzABl+NAlDhMnA0Yw27UHJfWY6UWZ3Wa73DQCWsdZ6eydal4g8YNA5pB
+6UjMQKWh/bXHZl8v+eCuuXODXZQGazKOFFoc6SGumxAcuLraCBFsuU5m4AQ0NA=
=v+g2
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"These are the two bug fixes I mentioned in the final merge window
pull. One is a reversed logic check in the device busy tests which
can cause a nasty hang and another crash seen in the new SCSI pool
support if the use count ever goes to zero"
[ The device busy test already got merged from a patch earlier, so is
now duplicated. ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] save command pool address of Scsi_Host
[SCSI] fix qemu boot hang problem
Sébastien Barré