Use the typical startup times from the data sheet so boards get a
reasonable default. Not setting any enable time can lead to board hangs
when e.g. clocks are enabled too soon afterwards.
This fixes gpu power domain resume on the Librem 5.
[Moved #defines into driver, seems to be general agreement and avoids any
cross tree issues -- broonie]
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/41fb2ed19f584f138336344e2297ae7301f72b75.1608316658.git.agx@sigxcpu.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Setups where regulator (especially the buck8) output voltage is scaled
by adding external connection where some other regulator output is
connected to feedback-pin (over suitable resistors) is getting popular
amongst users of BD71837. This allows for example scaling down the
buck8 voltages to suit lover GPU voltages for projects where buck8 is
(ab)used to supply power for GPU. As a note - some setups do allow DVS
for buck8. This do produce voltage spikes and the HW must be evaluated
to be able to survive them. Thus this commit still keep the DVS disabled
for non DVS bucks by default. Let's not help you burn your proto board.
Allow describing this external connection from DT and scale the
voltages accordingly. This is what the connection should look like:
|------------|
| buck 8 |-------+----->Vout
| | |
|------------| |
| FB pin |
| |
+-------+--R2---+
|
R1
|
V FB-pull-up
Here the buck output is sifted according to formula:
Vout_o = Vo - (Vpu - Vo)*R2/R1
Linear_step = step_orig*(R1+R2)/R1
where:
Vout_o is adjusted voltage output at vsel reg value 0
Vo is original voltage output at vsel reg value 0
Vpu is the pull-up voltage V FB-pull-up in the picture
R1 and R2 are resistor values.
Bring support for specifying the Vpu, R1 and R2 from device tree and
scale voltages if they are given.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/89b2be87074f307a8823f15f34e1f662023cbf36.1604994184.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix sparse warnings:
drivers/regulator/bd718x7-regulator.c:576:28: warning: symbol 'bd71847_swcontrol_ops' was not declared. Should it be static?
drivers/regulator/bd718x7-regulator.c:585:28: warning: symbol 'bd71847_hwcontrol_ops' was not declared. Should it be static?
drivers/regulator/bd718x7-regulator.c:902:28: warning: symbol 'bd71837_swcontrol_ops' was not declared. Should it be static?
drivers/regulator/bd718x7-regulator.c:913:28: warning: symbol 'bd71837_hwcontrol_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20200910034240.37268-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The BD718(37/47/50) regulator enable states can be controlled
either by SW or by PMIC internal state machine. The bd718x7
driver has not supported leaving the regulators under HW state
machine control (except for cases where this is required to
avoid boot-up problems due to critical regulators being turned
OFF at reset when SNVS used as reset state).
On some systems this is undesirable as there now are setups where
mixture of SW and HW state machine controlled regulators is needed.
Specifically, some SoCs signal SUSPEND state change to PMIC via
STBY_REQ line. Now there are setups that expect certain regulators
then to be disabled (by PMIC state machine) while other regulators
should stay enabled (regardless of HW state => SW control required).
Add support for a new device-tree property
"rohm,no-regulator-enable-control" which can be used to leave
regulator(s) under HW state machine control.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/6ebba33dd08f2dcc9f1137bbff4d2dc905278a5a.1599029335.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The BD71837 had a HW "feature" where changing the regulator output
voltages of other regulators but bucks 1-4 might cause spikes if
regulators were enabled. Thus SW prohibit voltage changes for other
regulators except for bucks 1-4 when regulator is enabled.
The HW colleagues did inadvertly fix this issue for BD71847 and
BD71850.
The power-good detection for LDOs can still cause false alarms if
LDO voltage is changed upwards when LDO is enabled.
Allow LDO voltage changes and disabe the power-good monioring for
the duration of the LDO voltage change and enable it after LDO
voltage has stabilized. ROHM HW colleagues measured the safety
limit of 1000uS for guaranteeing the voltage has stabilized. Let's
use that for starters and add confiurable stabilization wait-time
later if needed.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20200513143921.GA22143@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl61lKwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HxeB/9dblIbC+28MvcEHXCcYBZBouOnrM8E
bIOMXkgEj1uL78ozOm7tMCgEpaKgv6BHdDuClCBvjbr0uOtAi0qUiv0IBotuVrdo
lq73l8l7OPz6TFFKIt8WsgwKnzdkuQC08+qrZasAdluRQnqnmkU2tvl2y9zaaaR4
6hGw+Nwx/pgeCXCa3pu+rCYwA7g0Tf8a6DDC6LyQWZameBJ1ey/YDjhJEeSmY7P7
306zs8YVxHhQMLUQ5T7DA6r/KWMNkO1SOueCqTjxWZc/XamGEcbsZG1cWrAnkoE2
VKLXBtYC75coNxIiu8ZxnQwLLdz1EQPdtg0qmzSjXJ68QjbWWzf4K1ra
=LG9G
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl61lPUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0GuGB/9kDFxKo0DWsH6tqZGS/retk0ddT+4B
mnkkZGvoKkkDe1lh84vRbrPHhiI9LIXaj3lFgzyYeTuAi9tb77mPNnYIPLDye7bO
OvgJgovo4tK3dUVSUFatvOhuAMSZLyN2WjWRX+YeHMd1nNZSHxEz0CuG3npNtuKa
KoZd0Dfom4ds66qDlWdfonFhMJbMvQbEs4BhnfdvpD/soylyDB+29SHlhTBv8+UC
I7BNzsmVDlp/JyrX3yJbuTum9wbPaMLcyL96EbvRykmTywz5FXudffqzPfPnoQxT
rbN5DfwKsnySToUYDfp9dcIMyTF0/MtneaeBMRu2NIkpMmnicvExNrbU
=/+DM
-----END PGP SIGNATURE-----
Merge tag 'linear-ranges-lib' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-5.8
lib: Add linear ranges helper library and start using it
Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
Change the regulator helpers to use common linear_ranges code.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/64f01d5e381b8631a271616b7790f9d5640974fb.1588944082.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The BD71837 had a HW "feature" where changing the regulator output
voltages of other regulators but bucks 1-4 might cause spikes if
regulators were enabled. Thus SW prohibit voltage changes for other
regulators except for bucks 1-4 when regulator is enabled.
The HW colleagues did inadvertly fix this issue for BD71847 and
BD71850. Remove voltage change restrictions from other PMICs but
BD71837.
The LDO voltage changing is still restricted. I did not yet receive
answer whether there is voltage spikes to be expected for LDOs. I
only know that the power-good detection for LDOs can cause false
alarms if LDO voltage is changed when LDO is enabled. We might be
able to work-around this by disabling the power-good monioring for
the duration of the LDO voltage change - but as I said, I don't
know yet. Let's fix it later if we can confirm that also LDO voltage
changes are safe.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20200428092930.GA9721@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
- New Device Support
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
- New Functionality
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
- Fix-ups
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers; madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
- Bug Fixes
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon
-----BEGIN PGP SIGNATURE-----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=t4+B
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
Few ROHM PMICs allow setting the voltage states for different system states
like RUN, IDLE, SUSPEND and LPSR. States are then changed via SoC specific
mechanisms. bd718x7 driver implemented device-tree parsing functions for
these state specific voltages. The parsing functions can be re-used by
other ROHM chip drivers like bd71828. Split the generic functions from
bd718x7-regulator.c to rohm-regulator.c and export them for other modules
to use.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Thanks to Stephen Boyd I today learned we can use platform_device_id
to do device and module matching for MFD sub-devices!
Do device matching using the platform_device_id instead of using
explicit module_aliases to load modules and custom parent-data field
to do module loading and sub-device matching.
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Nowdays ROHM_CHIP_TYPE_AMOUNT includes not only BD71837/BD71847 but also
BD70528/BD71828 which are not supported by this driver. So it seems not
necessay to have pmic_regulators[ROHM_CHIP_TYPE_AMOUNT] as mapping table.
Simplify the code by removing struct bd718xx_pmic_inits and
pmic_regulators[ROHM_CHIP_TYPE_AMOUNT].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20200108014256.11282-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Set 'struct device' fwnode when registering a new device
- New Drivers
- Add support for ROHM BD70528 PMIC
- New Device Support
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
- New Functionality
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
- Fix-ups
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
- Bug Fixes
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera
-----BEGIN PGP SIGNATURE-----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=A3jw
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Set 'struct device' fwnode when registering a new device
New Drivers:
- Add support for ROHM BD70528 PMIC
New Device Support:
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
New Functionality:
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
Fix-ups:
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
Bug Fixes:
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera"
* tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (45 commits)
mfd: hi655x-pmic: Fix missing return value check for devm_regmap_init_mmio_clk
mfd: madera: Fixup SPDX headers
mfd: madera: Remove some unused registers and fix some defaults
mfd: intel-lpss: Release IDA resources
mfd: intel-lpss: Add Intel Elkhart Lake PCH PCI IDs
mfd: cs5535-mfd: Remove ifdef OLPC noise
mfd: stmfx: Fix macro definition spelling
dt-bindings: mfd: Add link to ROHM BD71847 Datasheet
MAINAINERS: Swap words in INTEL PMIC MULTIFUNCTION DEVICE DRIVERS
mfd: cros_ec_dev: Register cros_ec_accel_legacy driver as a subdevice
mfd: rk808: Prepare rk805 for poweroff
mfd: rk808: Check pm_power_off pointer
mfd: cros_ec: differentiate SCP from EC by feature bit
dt-bindings: Add binding for cros-ec-rpmsg
mfd: madera: Add Madera core support for CS47L92
mfd: madera: Add Madera core support for CS47L15
mfd: madera: Update DT bindings to add additional CODECs
mfd: madera: Add supply mapping for MICVDD
mfd: madera: Fix potential uninitialised use of variable
mfd: madera: Fix bad reference to pinctrl.txt file
...
Split the bd718x7.h to ROHM common and bd718x7 specific parts
so that we do not need to add same things in every new ROHM
PMIC header. Please note that this change requires changes also
in bd718x7 sub-device drivers for regulators and clk.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver does not use any symbols from <linux/gpio.h>
so just drop the include.
Cc: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use rdev_get_id() instead of directly access rdev->desc->id.
While at it also remove unneeded init for ramp_value variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
read ROHM BD71837 / BD71847 specific device tree bindings for
controlling the PMIC shutdown/reset states and voltages for
different HW states. The PMIC was designed to be used with NXP
i.MX8 SoC and it supports SNVS low power state which seems to
be typical for NXP i.MX SoCs. However, when SNVS is used we must
not allow SW to control enabling/disabling those regulators which
are crucial for system to boot as there is a HW limitation which
causes SW controlled regulators to be kept shut down after SNVS
reset.
Allow setting the SNVS to be used as reset target state and allow
marking those regulators which are critical for boot.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
BD71837 and BD71847 have a HW functionality which leave power
rails OFF after powerof state:
- if they have been controlled by SW.
- if state transition from poweroff is done to SNVS
BD71837 can after reset transition from power-off to SNVS or
READY state depending on reset reason. By default only wathcdog
reset changes state from poweroff to ready. Change PMIC
configuration to always transition to READY in order to avoid
crucial power rails being OFF after reset.
If SNVS is required the crucial power rails should not be
controlled by SW - eg corresponding regulator control register
should have SEL bit kept zero. Currently the driver assumes all
regulators to be controlled by SW so it sets all SEL bits to 1.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The voltages in bd718xx_3rd_nodvs_buck_volts are in ascendant order, so use
regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
0-Day tests found compilation error on x86.
Driver won't compile on x86_64 as "of_match_ptr" is
not found. Add missing include <linux/of.h>
At some point this fix was lost. So re-apply it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With gcc 4.1:
drivers/regulator/bd718x7-regulator.c: In function ‘bd718xx_probe’:
drivers/regulator/bd718x7-regulator.c:1020: warning: initialization from incompatible pointer type
drivers/regulator/bd718x7-regulator.c:1024: warning: initialization from incompatible pointer type
Apparently this old compiler can't handle the obscure double
indirection.
However, there is no need for a double indirection. Just store a
pointer to the array instead, like other drivers tend to do.
Fixes: 494edd266b ("regulator/mfd: Support ROHM BD71847 power management IC")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
All the fields in struct bd718xx_pmic are not really necessary.
Remove struct bd718xx_pmic to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rename bd71837-regulator.c to bd718x7-regulator.c to reflect the
fact that also BD71847 is now supported by the driver.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Guido Günther