This contains a couple of fixes and cleanups for the Meson and ACPI/LPSS
drivers as well as capture support for STM32. Note that given the cross-
subsystem changes, the STM32 patches were merged through the MFD and PWM
trees, both sharing an immutable branch.
-----BEGIN PGP SIGNATURE-----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=ZED5
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains a couple of fixes and cleanups for the Meson and
ACPI/LPSS drivers as well as capture support for STM32.
Note that given the cross- subsystem changes, the STM32 patches were
merged through the MFD and PWM trees, both sharing an immutable
branch"
* tag 'pwm/for-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: stm32: Fix build warning with CONFIG_DMA_ENGINE disabled
pwm: stm32: Enforce dependency on CONFIG_MFD_STM32_TIMERS
ACPI / LPSS: Add missing prv_offset setting for byt/cht PWM devices
pwm: lpss: platform: Save/restore the ctrl register over a suspend/resume
dt-bindings: mfd: stm32-timers: Add support for dmas
pwm: simplify getting .drvdata
pwm: meson: Fix allocation of PWM channel array
Without dmaengine support, we get a harmless warning about an unused
function:
drivers/pwm/pwm-stm32.c:166:12: error: 'stm32_pwm_capture' defined but not used [-Werror=unused-function]
Changing the #ifdef to an IS_ENABLED() check shuts up that warning and
is slightly nicer to read.
Fixes: 53e38fe73f ("pwm: stm32: Add capture support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
-----BEGIN PGP SIGNATURE-----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=e4zs
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-pwm-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into for-next
Immutable branch between MFD and PWM due for the v4.18 merge window (v2)
When compile-testing the PWM driver without also enabling the
stm32_timers MFD, we run into a link error:
drivers/pwm/pwm-stm32.o: In function `stm32_pwm_raw_capture.isra.6':
pwm-stm32.c:(.text+0xcb0): undefined reference to `stm32_timers_dma_burst_read'
We don't need the '|| COMPILE_TEST' here, since stm32_timers itself
can be built with CONFIG_COMPILE_TEST on all architectures, so we do
get the coverage through allmodconfig and randconfig builds even
when we make it a hard dependency.
Fixes: 7edf736920 ("pwm: Add driver for STM32 plaftorm")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
On some devices the contents of the ctrl register get lost over a
suspend/resume and the PWM comes back up disabled after the resume.
This is seen on some Bay Trail devices with the PWM in ACPI enumerated
mode, so it shows up as a platform device instead of a PCI device.
If we still think it is enabled and then try to change the duty-cycle
after this, we end up with a "PWM_SW_UPDATE was not cleared" error and
the PWM is stuck in that state from then on.
This commit adds suspend and resume pm callbacks to the pwm-lpss-platform
code, which save/restore the ctrl register over a suspend/resume, fixing
this.
Note that:
1) There is no need to do this over a runtime suspend, since we
only runtime suspend when disabled and then we properly set the enable
bit and reprogram the timings when we re-enable the PWM.
2) This may be happening on more systems then we realize, but has been
covered up sofar by a bug in the acpi-lpss.c code which was save/restoring
the regular device registers instead of the lpss private registers due to
lpss_device_desc.prv_offset not being set. This is fixed by a later patch
in this series.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This removes build warning when COMPILE_TEST=y and MFD_STM32_TIMERS=n
in drivers/pwm/pwm-stm32.c. In function 'stm32_pwm_capture' 'raw_prd' and
'raw_dty' may be used uninitialized in this function
[-Wmaybe-uninitialized]
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Using input prescaler, capture unit will trigger DMA once every
configurable /2, /4 or /8 events (rising edge). This helps improve
period (only) capture accuracy at high rates.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently, capture is based on timeout window to configure prescaler.
PWM capture framework provides 1s window at the time of writing.
There's place for improvement, after input signal has been captured once:
- Finer tune counter clock prescaler, by using 1st capture result (with
arbitrary margin).
- Do a 2nd capture, with scaled capture window.
This increases accuracy, especially at high rates.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for PMW input mode on pwm-stm32. STM32 timers support
period and duty cycle capture as long as they have at least two PWM
channels. One capture channel is used for period (rising-edge), one
for duty-cycle (falling-edge).
When there's only one channel available, only period can be captured.
Duty-cycle is simply zero'ed in such a case.
Capture requires exclusive access (e.g. no pwm output running at the
same time, to protect common prescaler).
Timer DMA burst mode (from MFD core) is being used, to take two
snapshots of capture registers (upon each period rising edge).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Using the pwm-meson driver on the 32-bit SoCs causes memory corruption.
The result are some hard-to-explain errors, for example
devm_clk_register() crashes with a NULL dereference somewhere deep in
the common clock framework code. In some cases the kernel even refused
to boot when any of the PWM controllers were enabled on Meson8b.
The root cause is an incorrect memory size in the devm_kcalloc() call in
meson_pwm_probe(). The code allocates an array of meson_pwm_channel
structs, but the size given is the size of the meson_pwm struct (which
seems like a small copy-and-paste error, as meson_pwm is allocated a few
lines above).
Even with this typo the code seemed to work fine on the 64-bit GX SoCs
(maybe due to the structs having the same size in the compiled result,
but I haven't checked this further).
Fixes: 211ed63075 ("pwm: Add support for Meson PWM Controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This set of changes adds support for more generations of the RCar
controller as well as runtime PM support. The JZ4740 driver gains
support for device tree and can now be used on all Ingenic SoCs.
Rounding things off is a random assortment of fixes and cleanups
all across the board.
-----BEGIN PGP SIGNATURE-----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=JiRM
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes adds support for more generations of the RCar
controller as well as runtime PM support. The JZ4740 driver gains
support for device tree and can now be used on all Ingenic SoCs.
Rounding things off is a random assortment of fixes and cleanups all
across the board"
* tag 'pwm/for-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (29 commits)
pwm: rcar: Add suspend/resume support
pwm: rcar: Use PM Runtime to control module clock
dt-bindings: pwm: rcar: Add bindings for R-Car M3N support
pwm: rcar: Fix a condition to prevent mismatch value setting to duty
pwm: sysfs: Use put_device() instead of kfree()
dt-bindings: pwm: sunxi: Add new compatible strings
pwm: sun4i: Simplify controller mapping
pwm: sun4i: Drop unused .has_rdy member
pwm: sun4i: Properly check current state
pwm: Remove depends on AVR32
pwm: stm32: LPTimer: Use 3 cells ->of_xlate()
dt-bindings: pwm-stm32-lp: Add #pwm-cells
pwm: stm32: Protect common prescaler for all channels
pwm: stm32: Remove unused struct device
pwm: mediatek: Improve precision in rate calculation
pwm: mediatek: Remove redundant MODULE_ALIAS entries
pwm: mediatek: Fix up PWM4 and PWM5 malfunction on MT7623
pwm: jz4740: Enable for all Ingenic SoCs
pwm: jz4740: Add support for devicetree
pwm: jz4740: Implement ->set_polarity()
...
This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips
in mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older
PXA and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure
is needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HD9V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
Runtime PM API (pm_runtime_get_sync/pm_runtime_put) should be used
to control module clock instead of clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: Hien Dang <hien.dang.eb@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch fixes an issue that is possible to set mismatch value to duty
for R-Car PWM if we input the following commands:
# cd /sys/class/pwm/<pwmchip>/
# echo 0 > export
# cd pwm0
# echo 30 > period
# echo 30 > duty_cycle
# echo 0 > duty_cycle
# cat duty_cycle
0
# echo 1 > enable
--> Then, the actual duty_cycle is 30, not 0.
So, this patch adds a condition into rcar_pwm_config() to fix this
issue.
Signed-off-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
[shimoda: revise the commit log and add Fixes and Cc tags]
Fixes: ed6c1476bf ("pwm: Add support for R-Car PWM Timer")
Cc: Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Never directly free @dev after calling device_register(), even if it
returned an error! Always use put_device() to give up the reference
initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
At the moment we assign our supported compatible strings to a respective
instance of our sun4i_pwm_data structure, even though some of them
are the same.
To avoid further clutter, split out the three different combinations of
features we have at the moment and name them accordingly.
This should make it more obvious which compatible string to use for new
SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Commit a054c4d684 ("pwm: sun4i: Drop legacy callbacks") dropped the
only user of the .has_rdy member in our sun4i_pwm_data struct.
Consequently we don't need to store this anymore for the various SoCs,
which paves the way for further simplifications.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Correctly extract the prescaler value from CTRL_REG before comparing it
to PWM_PRESCAL_MASK.
Also, check that both PWM_CLK_GATING and PWM_EN to ensure the PWM is
enabled instead of relying on only one of those.
Fixes: 93e0dfb2c5 ("pwm: sun4i: Improve hardware read out")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
AVR32 is gone, so no more need to depend on it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There may be a race, when configuring two PWM channels, with different
prescaler values, when there's no active channel yet.
Add mutex lock to avoid concurrent access on PWM apply state.
This is also precursor patch for PWM capture support.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
dev is never assigned or used. Remove it.
Fixes: 7edf736920 ("pwm: Add driver for STM32 plaftorm")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add a way that turning resolution from in nanosecond into in picosecond
to improve noticeably almost 4.5% precision.
It's necessary to hold the new resolution with type u64 and thus related
operations on u64 are applied instead in those rate calculations.
And the patch has a dependency on [1].
[1] http://lists.infradead.org/pipermail/linux-mediatek/2018-March/012225.html
Cc: stable@vger.kernel.org
Fixes: caf065f8fd ("pwm: Add MediaTek PWM support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
MODULE_ALIAS exports information to allow the module to be auto-loaded at
boot for the drivers registered using legacy platform registration.
However, currently the driver is always used by DT-only platform,
MODULE_ALIAS is redundant and should be removed properly.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since the offset for both registers, PWMDWIDTH and PWMTHRES, used to
control PWM4 or PWM5 are distinct from the other PWMs, whose wrong
programming on PWM hardware causes waveform cannot be output as expected.
Thus, the patch adds the extra condition for fixing up the weird case to
let PWM4 or PWM5 able to work on MT7623.
v1 -> v2: use pwm45_fixup naming instead of pwm45_quirk
v2 -> v3: add more tags for Reviewed-by, Fixes, and Cc stable
Cc: stable@vger.kernel.org
Fixes: caf065f8fd ("pwm: Add MediaTek PWM support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Zhi Mao <zhi.mao@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This driver works perfectly with all the versions of the SoCs from
Ingenic that are supported upstream.
This makes the driver usable on JZ4740, JZ4770 and JZ4780 SoCs.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add support for probing the pwm-jz4740 directly from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This permits clients of this driver to specify the polarity to use for
their PWM channel.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
On the JZ4750 and later SoCs, channel 1 and 2 operate in a different
way (TCU2 mode) as the other channels. If a TCU2 mode counter is
stopped before its PWM functionality is disabled, the output is not
guaranteed to return to the initial level.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
On a imx6q-cubox-i board, which has an LED driven by PWM, when the system
goes into suspend the PWM block is disabled by default, then the PWM pin
goes to logic level zero and turn on the LED during suspend, which is not
really the behaviour we want to see.
By keeping the PWM enabled during suspend via STOPEN bit, the pwm-leds
driver sets the brightness to zero in suspend and then the LED is
turned off as expected.
So always set the STOPEN to fix the PWM behaviour in suspend.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add SPDX identifier to make it easier to determine the license of the
file.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The blackfin architecture is getting removed, so this driver is now
obsolete as well.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
For PWM controller in the Meson-AXG SoC, the EE domain and AO domain
have different clock sources. This patch tries to describe them in the
DT compatible data.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Notifications for devices without bus or class set get dropped by
dev_uevent_filter(). Adding the class to the exported child matches
what the GPIO subsystem is doing.
With this change exporting a channel triggers a udev event, which
gives userspace a chance to fixup permissions and makes it possible
for non-root users to make use of the PWM subsystem.
Signed-off-by: Gottfried Haider <gottfried.haider@gmail.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: H Hartley Sweeten <hsweeten@visionengravers.com>
CC: linux-pwm@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-rpi-kernel@lists.infradead.org
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The changes for this release include power management improvements for
the pwm-img driver, support for the backup mode on pwm-atmel-tcb as well
as support for more hardware with the R-Car and Mediatek drivers.
To round things off there's a bit of cleanup for sunxi and stm32-lp.
-----BEGIN PGP SIGNATURE-----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=HLrm
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The changes for this release include power management improvements for
the pwm-img driver, support for the backup mode on pwm-atmel-tcb as
well as support for more hardware with the R-Car and Mediatek drivers.
To round things off there's a bit of cleanup for sunxi and stm32-lp"
* tag 'pwm/for-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: stm32-lp: Remove pwm_is_enabled() check before calling pwm_disable()
pwm: mediatek: Add MT2712/MT7622 support
pwm: sunxi: Use of_device_get_match_data()
pwm: atmel-tcb: Support backup mode
dt-bindings: pwm: Add R-Car D3 device tree bindings
pwm: img: Add runtime PM
pwm: img: Add suspend / resume handling
The same checking is done by the implementation of pwm_disable().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add support for MT2712 and MT7622. Due to register offset address of
pwm7 for MT2712 is not fixed 0x40, add mtk_pwm_reg_offset array for PWM
register offset.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The usage of of_device_get_match_data reduce the code size a bit.
Furthermore, it prevents an improbable dereference when
of_match_device() returns NULL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Save and restore registers for the PWM on suspend and resume, which
makes hibernation and backup modes possible.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add runtime PM to disable the clocks when the h/w is not in use.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The power may be disabled during suspend, so implement suspend and
resume callbacks to save and restore register state.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
[thierry.reding@gmail.com: guard using PM_SLEEP instead of PM]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds