With reset port, set clock and get clock functions in SoC specific extentions
being removed, only the driver probe is left over in these extensions. The
probe function itself can be merged into one and moved into the samsung common
serial driver. With driver probe also moved, all the SoC specific extentions
are no longer required and they are deleted.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With clkdev based clock lookup support, the clock set and get operation
using clock names communicated between the samsung uart driver and the
SoC specific extension can be removed.
In addition to that, for each platform specific extension, add the
default clock selection, number of clock options for uart baud generator,
clock selection bit mask and shift values which is required by the
clkdev support in samsung uart driver.
The default clock selection value 'def_clk_sel' specifies the default clock
to be used as the source clock for baud rate generator in case the platform
code does not specify the same.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With clkdev based clock lookup added to samsung serial driver, the use
of 'struct s3c24xx_uart_clksrc' to supply clock names in platform
data is removed from all the Samsung platform code.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Ramax Lo <ramaxlo@gmail.com>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Instead of using clock names supplied in platform data, use a generic
clock name 'clk_uart_baud' to look up clocks. The platform code should
register clocks with the name 'clk_uart_baud' which can be used by the
baud rate generator. The clock lookup and selection of the best clock
as baud rate clock is reworked.
Platform code can specify the clocks that can be used as source for the
baud clock (as supported previously by passing names of clocks). A new
member is added to the platform data 'clk_sel' which holds a bit-field
value with each bit representing a baud source clock. If a bit at any
bit position is set, that clock is looked up to participate in the
selection of the baud clock source.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With uart tx/rx/err interrupt handling moved into the driver for s3c64xx
and later SoC's, the uart interrupt handling in plaform code can be removed.
The uart device irq resources is reduced to one and the related unused
macros are removed.
Suggested-by: Grant Likely <grant.likely@secretlab.ca>
CC: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit bcae8aeb32 "[ARM] S3C24A0: Initial architecture support files"
brought in a bunch of files while explicitly leaving out the corresponding
Kconfig entry, stating that the series is not complete.
More than 2.5 years later, the support for this has not seen any progress.
This is therefore dead code. If someone wants to revive this code, it is
always possible to retrieve it from the Git repository.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This patch fixes the way of comparison for handling of two or more
clock sources for UART.
For example, if just only one clock source is defined even though
there are two clock sources for UART, the serial driver does not
set proper clock up. Of course, it is problem.
So this patch changes the condition of comparison to avoid useless
setup clock and adds a flag 'NO_NEED_CHECK_CLKSRC' which means
selection of source clock is not required.
In addition, since the Exynos4210 has only one clock source for UART
this patch adds the flag into its common_init_uarts().
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the FRACVAL register on the newer UART blocks which provides
the same function as UDIVSLOT register but the FRACVAL is easier to implement.
To support UDIVSLOT register, UDIVSLOT table search is necessary though
supporting FRACVAL only needs the index value of UDIVSLOT table.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Acked-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move common headers from plat-s3c's include/plat directory into plat-samsung.
No need to fix any files, these are still included via <plat/>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-02-23 00:03:42 +00:00
Renamed from arch/arm/plat-s3c/include/plat/regs-serial.h (Browse further)
