Previously, we've fired all our completion callbacks straight from our ISR.
Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now allow up to 126 VFs. Note though that certain firmware
versions only allow up to 80 VFs. Moreover, old HCAs only support 64 VFs.
In these cases, we limit the maximum number of VFs to 64.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the driver queried the firmware in order to get the number
of supported EQs. Under SRIOV, since this was done before the driver
notified the firmware how many VFs it actually needs, the firmware had
to take into account a worst case scenario and always allocated four EQs
per VF, where one was used for events while the others were used for completions.
Now, when the firmware supports the asymmetric allocation scheme, denoted
by exposing num_sys_eqs > 0 (--> MLX4_DEV_CAP_FLAG2_SYS_EQS), we use the
QUERY_FUNC command to query the firmware before enabling SRIOV. Thus we
can get more EQs and MSI-X vectors per function.
Moreover, when running in the new firmware/driver mode, the limitation
that the number of EQs should be a power of two is lifted.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing received traffic, pass CHECKSUM_COMPLETE status to the
stack, with calculated checksum for non TCP/UDP packets (such
as GRE or ICMP).
Although the stack expects checksum which doesn't include the pseudo
header, the HW adds it. To address that, we are subtracting the pseudo
header checksum from the checksum value provided by the HW.
In the IPv6 case, we also compute/add the IP header checksum which
is not added by the HW for such packets.
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to issue CONFIG_DEV "get" firmware command.
This command is used in order to obtain certain parameters used for
supporting various RX checksumming options and vxlan UDP port.
The GET operation is allowed for VFs too.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding ACCESS REG mlx4 command and use it to implement Query method for
PTYS (Port Type and Speed Register).
Query and store eth_prot_ctrl dev cap.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added new MAD_IFC command to read cable module info with attribute id (0xFF60).
Update include/linux/mlx4/device.h with function declaration (mlx4_get_module_info)
and the needed defines/enums for future use.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove unused variable ring->poll_cnt
- No need to set some fields if using blueflame
- Add missing const's
- Use unlikely
- Remove unneeded new line
- Make some comments more precise
- struct mlx4_bf @offset field reduced to unsigned int to save space
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the new flow, we separate the pci initialization and teardown
from the initialization and teardown of the other resources.
__mlx4_init_one handles the pci resources initialization. It then
calls mlx4_load_one to initialize the remainder of the resources.
When removing a device, mlx4_remove_one is invoked. However, now
mlx4_remove_one calls mlx4_unload_one to free all the resources except the pci
resources. When mlx4_unload_one returns, mlx4_remove_one then frees the
pci resources.
The above separation will allow us to implement 'reset flow' in the future.
It will also enable more EQs for VFs and is a pre-step to the modern API to
enable/disable SRIOV.
Also added nvfs; an integer array of size MLX4_MAX_PORTS + 1; to the mlx4_dev
struct. This new field is used to avoid parsing the num_vfs module parameter
each time the mlx4_restart_one is called.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is intended for archs having cache line larger then 64B.
Since our CQE/EQEs are generally 64B in those systems, HW will write
twice to the same cache line consecutively, causing pipe locks due to
he hazard prevention mechanism. For elements in a cyclic buffer, writes
are consecutive, so entries smaller than a cache line should be
avoided, especially if they are written at a high rate.
Reduce consecutive writes to same cache line in CQs/EQs, by allowing the
driver to increase the distance between entries so that each will reside
in a different cache line. Until the introduction of this feature, there
were two types of CQE/EQE:
1. 32B stride and context in the [0-31] segment
2. 64B stride and context in the [32-63] segment
This feature introduces two additional types:
3. 128B stride and context in the [0-31] segment (128B cache line)
4. 256B stride and context in the [0-31] segment (256B cache line)
Modify the mlx4_core driver to query the device for the CQE/EQE cache
line stride capability and to enable that capability when the host
cache line size is larger than 64 bytes (supported cache lines are
128B and 256B).
The mlx4 IB driver and libmlx4 need not be aware of this change. The PF
context behaviour is changed to require this change in VF drivers
running on such archs.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the vlan stripping policy of the QP isn't supported by older
firmware versions for the INIT2RTR command. Nevertheless, we've used it.
Fix that by doing this policy change using INIT2RTR only if the firmware
supports it, otherwise, we call UPDATE_QP command to do the task.
Fixes: 7677fc9 ('net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the function which we use to set VXLAN DMFS (flow-steering) rules
from mlx4_en to mlx4_core. This refactoring will allow the mlx4_ib driver
to call the helper for the use case of user-space RAW Ethernet QPs, such
that they can serve VXLAN traffic too.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use is_kdump_kernel() to detect kdump kernel, instead of reset_devices.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wOm0
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
"Main set of InfiniBand/RDMA updates for 3.17 merge window:
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes..."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (52 commits)
IB/srp: Fix return value check in srp_init_module()
RDMA/ocrdma: report asic-id in query device
RDMA/ocrdma: Update sli data structure for endianness
RDMA/ocrdma: Obtain SL from device structure
RDMA/uapi: Include socket.h in rdma_user_cm.h
IB/srpt: Handle GID change events
IB/mlx5: Use ARRAY_SIZE instead of sizeof/sizeof[0]
IB/mlx4: Use ARRAY_SIZE instead of sizeof/sizeof[0]
RDMA/amso1100: Check for integer overflow in c2_alloc_cq_buf()
IPoIB: Remove unnecessary test for NULL before debugfs_remove()
IB/mad: Add user space RMPP support
IB/mad: add new ioctl to ABI to support new registration options
IB/mad: Add dev_notice messages for various umad/mad registration failures
IB/mad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid multicast join attempts with invalid P_key
IB/umad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid flushing the workqueue from worker context
IB/ipoib: Use P_Key change event instead of P_Key polling mechanism
IB/ipath: Add P_Key change event support
mlx4_core: Add support for secure-host and SMP firewall
...
Secure-host is the general term for the capability of a device
to protect itself and the subnet from malicious host software.
This is achieved by:
1. Not allowing un-trusted entities to access device configuration
registers, directly (through pci_cr or pci_conf) and indirectly
(through MADs).
2. Hiding M_Key from untrusted entities.
3. Preventing the modification of GUID0 by un-trusted entities
4. Not allowing drivers on untrusted hosts to receive nor to transmit
packets over QP0 (SMP Firewall).
The secure-host capability depends on firmware handling all QP0
packets, and not passing these packets up to the driver. Any information
required by the driver for proper operation (e.g., SM lid) is passed
via events generated by the firmware while processing QP0 MADs.
Driver support mainly requires using the MAD_DEMUX FW command at startup,
where the feature is enabled/disabled through a procedure described in
the Mellanox HCA tools package.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
[ Fix error path in mlx4_setup_hca to go to err_mcg_table_free. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add few helper functions to support a mechanism of getting an MPT,
modifying it and updating the HCA with the modified object.
The code takes 2 paths, one for directly changing the MPT (and
sometimes its related MTTs) and another one which queries the MPT and
updates the HCA via fw command SW2HW_MPT. The first path is used in
native mode; the second path is slower and is used only in SRIOV.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When running in kdump kernel, reduce number of resources allocated for
the hardware. This will enable the NIC to operate in this low memory
environment at the expense of performance and some features not related
to the basic NIC functionality.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 40GE we can't use the default bw units for set ratelimit (100 Mbps)
since the max is 255*100 Mbps = 25 Gbps (not suited for 40GE), thus we need 1 Gbps units.
But for 10GE 1 Gbps units might be too bruit so we use the following solution.
For user set ratelimit <= 25 Gbps:
use 100 Mbps units * user_ratelimit (* 10).
For user set ratelimit > 25 Gbps:
use 1 Gbps units * user_ratelimit.
For user set unlimited ratelimit (0 Gbps):
use 1 Gbps units * MAX_RATELIMIT_DEFAULT (57)
Note: any value > 58 will damage the FW ratelimit computation, so we allow
a max and any higher value will be pulled down to 57.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ affinity notifier can only have a single notifier - cpu_rmap
notifier. Can't use it to track changes in IRQ affinity map.
Detect IRQ affinity changes by comparing CPU to current IRQ affinity map
during NAPI poll thread.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2eacc23 ("net/mlx4_core: Enforce irq affinity changes immediatly")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Modify the various routines used to allocate memory resources which
serve QPs in mlx4 to get an input GFP directive. Have the Ethernet
driver to use GFP_KERNEL in it's QP allocations as done prior to this
commit, and the IB driver to use GFP_NOIO when the IB verbs
IB_QP_CREATE_USE_GFP_NOIO QP creation flag is provided.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.
We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it. To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores. If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.
Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the sysfs interface for enabling QP0 on VFs for
selected VF/port.
By default, no VFs are enabled for QP0 operation.
To enable QP0 operation on a VF/port, under
/sys/class/infiniband/mlx4_x/iov/<b:d:f>/ports/x there are two new entries:
- smi_enabled (read-only). Indicates whether smi is currently
enabled for the indicated VF/port
- enable_smi_admin (rw). Used by the admin to request that smi
capability be enabled or disabled for the indicated VF/port.
0 = disable, 1 = enable.
The requested enablement will occur at the next reset of the
VF (e.g. driver restart on the VM which owns the VF).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This commit adds the infrastructure for enabling selected VFs to
operate SMI (QP0) MADs without restriction.
Additionally, for these enabled VFs, their QP0 proxy and tunnel QPs
are MLX QPs. As such, they operate over VL15. Therefore, they are
not affected by "credit" problems or changes in the VLArb table (which
may shut down VL0).
Non-enabled VFs may only create UD proxy QP0 qps (which are forced by
the hypervisor to send packets using the q-key it assigns and places
in the qp-context). Thus, non-enabled VFs will not pose a security
risk. The hypervisor discards any privileged MADs it receives from
these non-enabled VFs.
By default, all VFs are NOT enabled, and must explicitly be enabled
by the administrator.
The sysfs interface which operates the VF enablement infrastructure
is provided in the next commit.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, VFs in SRIOV VFs are denied QP0 access. The main reason
for this decision is security, since Subnet Management Datagrams
(SMPs) are not restricted by network partitioning and may affect the
physical network topology. Moreover, even the SM may be denied access
from portions of the network by setting management keys unknown to the
SM.
However, it is desirable to grant SMI access to certain privileged
VFs, so that certain network management activities may be conducted
within virtual machines instead of the hypervisor.
This commit does the following:
1. Create QP0 tunnel QPs for all VFs.
2. Discard SMI mads sent-from/received-for non-privileged VFs in the
hypervisor MAD multiplex/demultiplex logic. SMI mads from/for
privileged VFs are allowed to pass.
3. MAD_IFC wrapper changes/fixes. For non-privileged VFs, only
host-view MAD_IFC commands are allowed, and only for SMI LID-Routed
GET mads. For privileged VFs, there are no restrictions.
This commit does not allow privileged VFs as yet. To determine if a VF
is privileged, it calls function mlx4_vf_smi_enabled(). This function
returns 0 unconditionally for now.
The next two commits allow defining and activating privileged VFs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
use_prio was added as part of an infrastructure for running FCoE in A0 mode.
FCoE didn't get into Mellanox Upstream driver, and when it will, it won't be
using A0 steering mode.
Therefore we can safely deprecate this module parameter without hurting any
existing user.
CC: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During heavy traffic, napi is constatntly polling the complition queue
and no interrupt is fired. Because of that, changes to irq affinity are
ignored until traffic is stopped and resumed.
By registering to the irq notifier mechanism, and forcing interrupt when
affinity is changed, irq affinity changes will be immediatly enforced.
Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add implementation for the add/del vxlan port ndo calls, using the
CONFIG_DEV firmware command.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the CONFIG_DEV firmware command which we will use to
configure the UDP port assumed by the firmware for the VXLAN offloads.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
In wrapped commands, we need to verify and convert
the slave's port into the real physical port.
Furthermore, when sending the response back to the slave,
a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
The slave assumes that sqpn is used for QP1 communication.
If the slave is assigned to a port != (first port), we need
to adjust the sqpn that will direct its QP1 packets into the
correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
In B0 steering, gid[5] contains the port. It needs
to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
When a slave queries the hardware, it needs to view only
the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
The QP port is encoded in the sched_qp, thus in modify_qp we need
to encode the correct port in sched_qp.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the required data structures to support VFs with N (1 or 2)
ports instead of always using the number of physical ports.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,
This is achieved as follows:
Outgoing MADs:
1. Source MAC: obtained from the CQ completion structure
(struct ib_wc, smac field).
2. Destination MAC: obtained from the tunnel header
3. vlan_id: obtained from the tunnel header.
Incoming MADs
1. The source (i.e., remote) MAC and vlan_id are passed in
the tunnel header to the proxy QP1.
VST mode support:
For outgoing MADs, the vlan_id obtained from the header is
discarded, and the vlan_id specified by the Hypervisor is used
instead.
For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
"invalid" vlan (0xffff) is substituted when forwarding to the slave.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs: Remaining GIDS are divided evenly between VFs activated by the driver.
If the division is not even, lower-numbered VFs get an extra GID.
For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IB transport, the host determines the slave GIDs. For ETH (RoCE),
however, the slave's GID is determined by the IP address that the slave
itself assigns to the ETH device used by RoCE.
In this case, the slave must be able to write its GIDs to the HCA gid table
(at the GID indices that slave "owns").
This commit adds processing for the SET_PORT_GID_TABLE opcode modifier
for the SET_PORT command wrapper (so that slaves may modify their GIDS
for RoCE).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.
This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
This patch add the support for Ethernet L2 attributes in the
verbs/cm/cma structures.
When dealing with L2 Ethernet, we should use smac, dmac, vlan ID and priority
in a similar manner that the IB L2 (and the L4 PKEY) attributes are used.
Thus, those attributes were added to the following structures:
* ib_ah_attr - added dmac
* ib_qp_attr - added smac and vlan_id, (sl remains vlan priority)
* ib_wc - added smac, vlan_id
* ib_sa_path_rec - added smac, dmac, vlan_id
* cm_av - added smac and vlan_id
For the path record structure, extra care was taken to avoid the new
fields when packing it into wire format, so we don't break the IB CM
and SA wire protocol.
On the active side, the CM fills. its internal structures from the
path provided by the ULP. We add there taking the ETH L2 attributes
and placing them into the CM Address Handle (struct cm_av).
On the passive side, the CM fills its internal structures from the WC
associated with the REQ message. We add there taking the ETH L2
attributes from the WC.
When the HW driver provides the required ETH L2 attributes in the WC,
they set the IB_WC_WITH_SMAC and IB_WC_WITH_VLAN flags. The IB core
code checks for the presence of these flags, and in their absence does
address resolution from the ib_init_ah_from_wc() helper function.
ib_modify_qp_is_ok is also updated to consider the link layer. Some
parameters are mandatory for Ethernet link layer, while they are
irrelevant for IB. Vendor drivers are modified to support the new
function signature.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds support for allocating IB UD QPs that we can steer
traffic from. We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.
This command isn't supported for VFs.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.
This is done through the following elements:
- read tunneling device caps in QUERY_DEV_CAP
- add helper function to do SET_PORT for tunneling
- add DMFS VXLAN steering rule definitions
- add CQE and WQE checksum offload field definitions
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the infrastructure needed to support ndo_get_phys_port_id which
allows users to identify to which physical port a net-device is connected
to by reading a unique port id.
This will work for VFs and PFs.
The driver uses a new device capability - phys_port_id, The PF driver
reads the port phys_port_id from Firmware and stores it. The VF driver
reads the port phys_port_id from the PF using QUERY_FUNC_CAP command.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each RX/TX ring and its CQ, allocation is done on a NUMA node that
corresponds to the core that the data structure should operate on.
The assumption is that the core number is reflected by the ring index.
The affected allocations are the ring/CQ data structures,
the TX/RX info and the shared HW/SW buffer.
For TX rings, each core has rings of all UPs.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
