There's a bug in the IOAPIC code for level-triggered interrupts. Its
relatively easy to trigger by sharing (virtio-blk + usbtablet was the
testcase, initially reported by Gerd von Egidy).
The "remote_irr" variable is used to indicate accepted but not yet acked
interrupts. Its cleared from the EOI handler.
Problem is that the EOI handler clears remote_irr unconditionally, even
if it reinjected another pending interrupt.
In that case, kvm_ioapic_set_irq() proceeds to ioapic_service() which
sets remote_irr even if it failed to inject (since the IRR was high due
to EOI reinjection).
Since the TMR bit has been cleared by the first EOI, the second one
fails to clear remote_irr.
End result is interrupt line dead.
Fix it by setting remote_irr only if a new pending interrupt has been
generated (and the TMR bit for vector in question set).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Shadows for large guests can take a long time to tear down, so reschedule
occasionally to avoid softlockup warnings.
Signed-off-by: Avi Kivity <avi@qumranet.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/chrisw/lsm-2.6:
capabilities: remain source compatible with 32-bit raw legacy capability support.
LSM: remove stale web site from MAINTAINERS
Packet sending is driven by two flags, tx_ready and tx_queued.
It was possible, that there were queued data for sending and
hardware was flagged as blocked but in fact it was not.
The tx_queued was indicator but should be really a counter else
first fragmented packet resets tx_queued flag, but there may be
pending packets which do not get sent.
New semantics:
tx_ready - set, if hw is ready to send packet, no packet is being
transferred right now
set the flag right at the place where data are copied
into hw memory and not earlier without checking if it
was succesful
tx_queued - count of enqueued packets, including fragments
Tested-by: Michal Rokos <michal.rokos@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clear CR4.VMXE in hardware_disable. There's no reason to leave it set
after doing a VMXOFF.
VMware Workstation 6.5 checks CR4.VMXE as a proxy for whether the CPU is
in VMX mode, so leaving VMXE set means we'll refuse to power on. With this
change the user can power on after unloading the kvm-intel module. I
tested on kvm-67 and kvm-69.
Signed-off-by: Eli Collins <ecollins@vmware.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
To get zeroed out memory from a particular NUMA node. To be used by
sunrpc.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just a quick explanation of the pagemap interface from a userspace point
of view, and an example of how to use it (in English, not code).
Signed-off-by: Thomas Tuttle <ttuttle@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the user tries to read from a position that is not a multiple of 8, or
read a number of bytes that is not a multiple of 8, they have passed an
invalid argument to read, for the purpose of reading these files. It's
not an IO error because we didn't encounter any trouble finding the data
they asked for.
Signed-off-by: Thomas Tuttle <ttuttle@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since pagemap is all about examining pages mapped into processes' memory
spaces, it makes sense for kpagecount to return the map counts, not the
reference counts.
Signed-off-by: Thomas Tuttle <ttuttle@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds DMI system identifier for ThinkPad T61.
Originally written by Klaus S. Madsen.
Taken from http://launchpadlibrarian.net/10864950/hdaps-t61.patch
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Cc: Klaus S. Madsen <ubuntu@hjernemadsen.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch:
commit e9720acd72
Author: Pavel Emelyanov <xemul@openvz.org>
Date: Fri Mar 7 11:08:40 2008 -0800
[NET]: Make /proc/net a symlink on /proc/self/net (v3)
introduced a /proc/self/net directory without bumping the corresponding
link count for /proc/self.
This patch replaces the static link count initializations with a call that
counts the number of directory entries in the given pid_entry table
whenever it is instantiated, and thus relieves the burden of manually
keeping the two in sync.
[akpm@linux-foundation.org: cleanup]
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This hooks up the platform-specific [gs]et_rtc_time functions so that
kernels using CONFIG_RTC_CLASS have RTC support on most PowerPC platforms.
A new driver, and one which we've been shipping in Fedora for a while
already, since otherwise RTC support breaks.
[akpm@linux-foundation.org: fix Kconfig indenting]
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following compile error caused by
commit 4016a1390d
(mm/nommu.c: return 0 from kobjsize with invalid objects):
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/nommu.c: In function 'kobjsize':
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/nommu.c:112: error: 'memory_end' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/nommu.c:112: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/nommu.c:112: error: for each function it appears in.)
The patch also removes now no longer required memory_{start,end}
declarations inside access_ok().
Reported-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a bug when we are trying to verify that the reserve inode's
double indirect blocks point back to the primary gdt blocks. The fix is
obvious, we need to mod the gdb count by the addr's per block. You can
verify this with the following test case
dd if=/dev/zero of=disk1 seek=1024 count=1 bs=100M
losetup /dev/loop1 disk1
pvcreate /dev/loop1
vgcreate loopvg1 /dev/loop1
lvcreate -l 100%VG loopvg1 -n looplv1
mkfs.ext3 -J size=64 -b 1024 /dev/loopvg1/looplv1
mount /dev/loopvg1/looplv1 /mnt/loop
dd if=/dev/zero of=disk2 seek=1024 count=1 bs=50M
losetup /dev/loop2 disk2
pvcreate /dev/loop2
vgextend loopvg1 /dev/loop2
lvextend -l 100%VG /dev/loopvg1/looplv1
resize2fs /dev/loopvg1/looplv1
without this patch the resize2fs fails, with it the resize2fs succeeds.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Acked-by: Andreas Dilger <adilger@sun.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The nommu binfmt code uses ksize() for pointers returned from do_mmap()
which is wrong. This converts the call-sites to use the nommu specific
kobjsize() function which works as expected.
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Matt Mackall <mpm@selenic.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide documentation of the kernel-doc documentation conventions oriented
to kernel hackers.
Since I figure that there will be more people reading this
kernel-doc-nano-HOWTO.txt file who are kernel developers focused on the
rest of the kernel, than there will be readers of this file who are
documentation developers extracting that embedded kernel-doc
documentation, I have taken the liberty of making the new section added
here:
How to format kernel-doc comments
the first section of the kernel-doc-nano-HOWTO.txt file.
This first section is intended to introduce, motivate and provide basic
usage of the kernel-doc mechanism for kernel hackers developing other
portions of the kernel.
Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frame buffer and mode setting drivers can be built as modules,
so fb_mode_option needs to be exported to support these.
Prevents this error:
ERROR: "fb_mode_option" [drivers/ps3/ps3av_mod.ko] undefined!
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Edward Shishkin <edward.shishkin@gmail.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I made a change to u-boot that used the FP (Fractional Part) field of BRGR
to achieve more accurate baud rate generation. Unfortunately, the
atmel_serial driver looks at the whole BRGR register when trying to detect
the baud rate that the port is currently running at, so setting FP to a
nonzero value breaks the baud rate detection.
I'll sit on the u-boot patch for a while longer, but this is clearly a
bug in the atmel_serial driver which should be fixed.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When posting:
[PATCH 1/8] Scaling msgmni to the amount of lowmem
(see http://lkml.org/lkml/2008/2/11/171), I have added a KERN_INFO message
that is output each time msgmni is recomputed.
In http://lkml.org/lkml/2008/4/29/575 Tony Luck complained that this
message references an ipc namespace address that is useless.
I first thought of using an audit_log instead of a printk, as suggested by
Serge Hallyn. But unfortunately, we do not have any other information
than the namespace address to provide here too. So I chose to move the
message and output it only at boot time, removing the reference to the
namespace.
Signed-off-by: Nadia Derbey <Nadia.Derbey@bull.net>
Cc: Pierre Peiffer <peifferp@gmail.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When posting:
[PATCH 1/8] Scaling msgmni to the amount of lowmem
(see http://article.gmane.org/gmane.linux.kernel/637849/) I changed the
MSGPOOL value to make it fit what is said in the man pages (i.e. a size
in bytes).
But Michael Kerrisk rightly complained that this change could affect the
ABI. So I'm posting this patch to make MSGPOOL expressed back in Kbytes.
Michael, on his side, has fixed the man page.
Signed-off-by: Nadia Derbey <Nadia.Derbey@bull.net>
Cc: Pierre Peiffer <peifferp@gmail.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Original report: """I used to force my console to black-on-white by the
command `setterm -inversescreen on`. In 2.6.26-rc4, I get lots of black
background characters."""
Another addendum to commit c9e587ab. This was previously missed out since
I was not aware of what vc_decscnm was for.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Reported-by: <thunder7@xs4all.nl>
Tested-by: <thunder7@xs4all.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If cpu specific cpufreq driver(i.e. longrun) has "setpolicy" function,
governor object isn't set into cpufreq_policy object at "__cpufreq_set_policy"
function in driver/cpufreq/cpufreq.c .
This causes a null object access at "store_scaling_setspeed" and
"show_scaling_setspeed" function in driver/cpufreq/cpufreq.c when reading or
writing through /sys interface (ex. cat
/sys/devices/system/cpu/cpu0/cpufreq/scaling_setspeed)
Addresses:
http://bugzilla.kernel.org/show_bug.cgi?id=10654https://bugzilla.redhat.com/show_bug.cgi?id=443354
Signed-off-by: CHIKAMA Masaki <masaki.chikama@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The interlaced and double line mode bits should not be copied to new
console when the console is switched. Otherwise, the new console may be
set to incorrect refresh rate.
Also, the x and y offsets does not need to be copied.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This semaphore doesn't appear to be used, so remove it.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding a nonexistent cpu to a cpuset will be omitted quietly. It should
return -EINVAL.
Example: (real_nr_cpus <= 4 < NR_CPUS or cpu#4 was just offline)
# cat cpus
0-1
# /bin/echo 4 > cpus
# /bin/echo $?
0
# cat cpus
#
The same occurs when add a nonexistent mem.
This patch will fix this bug.
And when *buf == "", the check is unneeded.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Paul Jackson <pj@sgi.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug in add_to_pagemap. Previously, since pm->out was a char *,
put_user was only copying 1 byte of every PFN, resulting in the top 7
bytes of each PFN not being copied. By requiring that reads be a multiple
of 8 bytes, I can make pm->out and pm->end u64*s instead of char*s, which
makes put_user work properly, and also simplifies the logic in
add_to_pagemap a bit.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Thomas Tuttle <ttuttle@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Consider you added a 'c foo:bar r' permission to some cgroup and then (a
bit later) 'c'foo:bar w' for it. After this you'll see the
c foo:bar r
c foo:bar w
lines in a devices.list file.
Another example - consider you added 10 'c foo:bar r' permissions to some
cgroup (e.g. by mistake). After this you'll see 10 c foo:bar r lines in
a list file.
This is weird. This situation also has one more annoying consequence.
Having many items in a white list makes permissions checking slower, sine
it has to walk a longer list.
The proposal is to merge permissions for items, that correspond to the
same device.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently even if a task sits in an all-denied cgroup it can still mount
any block device in any mode it wants.
Put a proper check in do_open for block device to prevent this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Tested-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two functions, that need to get a device_cgroup from a task (they are
devcgroup_inode_permission and devcgroup_inode_mknod) make it in a strange
way:
They get a css_set from task, then a subsys_state from css_set, then a
cgroup from the state and then a subsys_state again from the cgroup.
Besides, the devices_subsys_id is read from memory, whilst there's a
enum-ed constant for it.
Optimize this part a bit:
1. Get the subsys_stats form the task and be done - no 2 extra
dereferences,
2. Use the device_subsys_id constant, not the value from memory
(i.e. one less dereference).
Found while preparing 2.6.26 OpenVZ port.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Paul Menage <menage@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is just picking the container_of out of cgroup_to_devcgroup into a
separate function.
This new css_to_devcgroup will be used in the 2nd patch.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces memory_read_from_buffer().
The only difference between memory_read_from_buffer() and
simple_read_from_buffer() is which address space the function copies to.
simple_read_from_buffer copies to user space memory.
memory_read_from_buffer copies to normal memory.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Doug Warzecha <Douglas_Warzecha@dell.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Abhay Salunke <Abhay_Salunke@dell.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Markus Rechberger <markus.rechberger@amd.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Bob Moore <robert.moore@intel.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Len Brown <lenb@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Cc: Brian King <brking@us.ibm.com>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bluetooth will be able to use this.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the name of the device from "rtc-ds1374" to just "ds1374", to match
what all other RTC drivers do. I seem to remember that this name was
chosen to avoid possible confusion with an older ds1374 driver, but that
driver was removed 3 months ago.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Although if people have questions about ARCnet, perhaps it's _better_
for them to be mailing dwmw2@cam.ac.uk about it...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include limits.h to get a definition of PATH_MAX.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We lost the marking of SIGWINCH as being OK to receive during stub
execution, causing a panic should that happen.
Cc: Benedict Verheyen <benedict.verheyen@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86_64 defines either memcpy or __memcpy depending on the gcc version, and
it looks like UML needs to follow that in its exporting.
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes os_get_task_size locate the bottom of the address space,
as well as the top. This is for systems which put a lower limit on mmap
addresses. It works by manually scanning pages from zero onwards until a
valid page is found.
Because the bottom of the address space may not be zero, it's not
sufficient to assume the top of the address space is the size of the
address space. The size is the difference between the top address and
bottom address.
[jdike@addtoit.com: changed the name to reflect that this function is
supposed to return the top of the process address space, not its size and
changed the return value to reflect that. Also some minor formatting
changes]
Signed-off-by: Tom Spink <tspink@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed duplicated include file "kern_util.h" in
arch/um/drivers/ubd_kern.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Protection against the host's time going backwards (eg, ntp activity on
the host) by keeping track of the time at the last tick and if it's
greater than the current time, keep time stopped until the host catches
up.
Cc: Nix <nix@esperi.org.uk>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update status and URL for the "Gary's Encyclopedia" entry.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Cc: Len Brown <len.brown@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kobjsize() has been abusing page->index as a method for sorting out
compound order, which blows up both for page cache pages, and SLOB's
reuse of the index in struct slob_page.
Presently we are not able to accurately size arbitrary pointers that
don't come from kmalloc(), so the best we can do is sort out the
compound order from the head page if it's a compound page, or default
to 0-order if it's impossible to ksize() the object.
Obviously this leaves quite a bit to be desired in terms of object
sizing accuracy, but the behaviour is unchanged over the existing
implementation, while fixing the page->index oopses originally reported
here:
http://marc.info/?l=linux-mm&m=121127773325245&w=2
Accuracy could also be improved by having SLUB and SLOB both set PG_slab
on ksizeable pages, rather than just handling the __GFP_COMP cases
irregardless of the PG_slab setting, as made possibly with Pekka's
patches:
http://marc.info/?l=linux-kernel&m=121139439900534&w=2http://marc.info/?l=linux-kernel&m=121139440000537&w=2http://marc.info/?l=linux-kernel&m=121139440000540&w=2
This is primarily a bugfix for nommu systems for 2.6.26, with the aim
being to gradually kill off kobjsize() and its particular brand of
object abuse entirely.
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As some m68k machines have plenty of libc5 binaries in active use, enable
CONFIG_COMPAT_BRK by default.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>