Properly register on-chip interrupt using the irqdomain logic. The
number of interrupts is taken from the devicetree node. That includes
the following changes:
- cpu_has_ipr() was converted from an inline function to a static bool
variable, so it can be set using the "marvell,intc-priority" property
inside the device node of the tree.
- IRQ_BASE was converted from a macro to a runtime variable so that it
can be initialized dynamically from the DT init code.
- irq_base() now uses pxa_irq_base and just adds an offset.
Hence, there are now no compile-time fixed values used in case of DT
initialization.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
GPIO0 and GPIO1 are linked to unique interrupt line in PXA series,
others are linked to another interrupt line. All GPIO are linked to one
interrupt line in MMP series.
Since gpio driver is shared between PXA series and MMP series, define
GPIO0 and GPIO1 as chained interrupt chip. So we can move out gpio code
from irq.c to gpio-pxa.c.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
ARM: pxa/cm-x300: properly set bt_reset pin
ARM: mmp: rename SHEEVAD to GPLUGD
ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
ARM: i.MX28: shift frac value in _CLK_SET_RATE
plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
ARM: mx5: fix clock usage for suspend
ARM: pxa: use correct __iomem annotations
ARM: pxa: sharpsl pm needs SPI
ARM: pxa: centro and treo680 need palm27x
ARM: pxa: make pxafb_smart_*() empty when not enabled
ARM: pxa: select POWER_SUPPLY on raumfeld
ARM: pxa: pxa95x is incompatible with earlier pxa
ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
ARM: pxa: pxa95x/saarb depends on pxa3xx code
ARM: pxa: allow selecting just one of TREO680/CENTRO
ARM: pxa: export symbols from pxa3xx-ulpi
ARM: pxa: make zylonite_pxa*_init declaration match code
ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
ARM: at91: add defconfig for at91sam9g45 family
ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
...
The definition of __exception_irq_entry for
CONFIG_FUNCTION_GRAPH_TRACER=y needs linux/ftrace.h, but this creates a
circular dependency with it's current home in asm/system.h. Create
asm/exception.h and update all current users.
v4: - rebase to rmk/for-next
v3: - remove redundant includes of linux/ftrace.h
v2: - document the usage restricitions of __exception*
Cc: Zoltan Devai <zdevai@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This tries to clear up the confusion between integers and iomem pointers
in the marvell pxa platform. MMIO addresses are supposed to be __iomem*
values, in order to let the Linux type checking work correctly. This
patch moves the cast to __iomem as far back as possible, to the place
where the MMIO virtual address windows are defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
before we start consolidating the individual platform implementations
of the gpio header files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Thanks Dmitry for providing a fix to the original code.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Replace sysdev classes and struct sys_device objects used for "core"
power management by the PXA platform code with struct syscore_ops
objects that are simpler.
This reduces the code size and the kernel memory footprint. It also
is necessary for removing sysdevs entirely from the kernel in the
future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reorder
irq_set_chip()
irq_set_chip_data()
irq_set_handler()
to
irq_set_chip()
irq_set_handler()
irq_set_chip_data()
so the next patch can combine irq_set_chip() and irq_set_handler() to
irq_set_chip_and_handler().
Automated conversion with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Define all IRQs in irqs.h. If some IRQs are sharing one IRQ number, define
them together. If some IRQs are sharing same name with different IRQ number,
define different IRQ.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since interrupt handler is changed to use interrupt priority, we also need
to save and restore these interrupt controller registers in suspend/resume
routine.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Tested-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The remaining registers are separated into:
- <mach/regs-ost.h>
- <mach/regs-rtc.h>
- <mach/regs-intc.h>
and then we can remove pxa-regs.h completely. Instead of #include this
file, let's:
1. include the specific <mach/regs-*.h> with care (if that's absolutely
necessary)
2. define the registers in the driver, make cleanly defined API to expose
the register access to external with sufficient reason
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This is part of the work making gpio.c generic enough, the changes
include:
1. move IRQ handling of GPIO 0 and 1 outside (and back into irq.c)
2. pxa_init_gpio() accepts a range for muxed GPIO IRQs, and an IRQ
number for the muxed GPIOs
3. __gpio_is_occupied() and __gpio_is_inverted() are made inline,
and are moved into <mach/gpio.h> instead of generic gpio.c
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Allow PXA IRQs to be numbered starting at 16, leaving 0 to 15 for the
ISA IRQs, if needed.
This patch depends on RMK's PXA_HAVE_BOARD_IRQS patch.
Signed-off-by: Marc Zyngier <marc.zyngier@altran.com>
Acked-by: Russel King <linux@arm.linux.org.uk>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both i2c-pxa.c and irq.c still include pxa2xx-gpio.h although is is not
needed anymore.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
of the PXA register definitions
2. this is actually a temporary move in the transition of PXA2xx to
use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To further clean up the GPIO and IRQ structure:
1. pxa_init_irq_gpio() and pxa_init_gpio() combines into a single
function pxa_init_gpio()
2. assignment of set_wake merged into pxa_init_{irq,gpio}() as
an argument
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes the code better organized and simplified a bit. The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.
This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable. The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)
The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).
"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
by
1. wrapping long lines and making comments tidy
2. using IRQ_TYPE_* instead of migration macros __IRQT_*
3. introduce a pr_debug() for the commented printk(KERN_DEBUG ...)
stuff
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
by:
1. introduce dedicated pxa_{mask,unmask}_low_gpio()
2. remove set_irq_chip(IRQ_GPIO_2_x, ...) which has already been
initialized in pxa_init_irq()
3. introduce dedicated pxa_init_gpio_set_wake()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. As David Brownell suggests, using ffs() is going to make the loop
a bit faster (by avoiding unnecessary shift and iteration)
2. Russell suggested find_{first,next}_bit() being used with the
gedr[] array
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds gpiolib support for the PXA architecture:
- move all GPIO API functions from generic.c into gpio.c
- convert the gpio_get/set_value macros into inline functions
This makes it easier to hook up GPIOs provided by external chips like
ASICs and CPLDs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Minor ARM fixup from David Brownell folded into this ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a function pxa_init_irq_set_wake() was introduced, so that
processor specific code could install their own version
code setting PFER and PRER registers within pxa_gpio_irq_type
are removed, and the edge configuration is postponed to the
(*set_wake) and copies the GRER and GFER register, which will
always be set up correctly by pxa_gpio_irq_type()
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This definition produces processor specific code in generic function
pxa_gpio_mode(), thus creating inconsistencies for support of pxa25x
and pxa27x in a single zImage.
As David Brownell suggests, make it a run-time variable and initialize
at run-time according to the number of GPIOs on the processor. For now
the initialization happens in pxa_init_irq_gpio(), since there is
already a parameter for that, besides, this is and MUST be earlier
than any subsequent calls to pxa_gpio_mode().
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As pointed out by Jrgen, we are overflowing the number of GPIOs
in pxa_init_irq_gpio(). I'm seeing the same problem on my HTC
Universal PXA270 based PDA.
According to Eric, the function argument is the number of GPIOs,
so we should keep the semantics and reduce the number of
iteration by 1.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
/* should be ok this time, I aligned this patch to your arm:pxa2.mbox */
1. move pxa25x specific IRQ initialization code to pxa25x_init_irq()
and pxa27x code to pxa27x_init_irq(), remove pxa_init_irq()
2. replace all pxa_init_irq() with their PXA25x or PXA27x specific
functions
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. use GPIO_IRQ_mask[] to select those bits of interest, actually
only those "unmasked" GPIO IRQs with their corresponding bits
in GPIO_IRQ_mask[] set to "1" should be checked
2. remove #ifdef PXA_LAST_GPIO > 96 .. #endif, GPIO_IRQ_mask[]
is used to mask out the irrelevant bits, so that even though
the GEDR3 on PXA25x is reserved, it will be masked, and the
following code will never run. Another point is that GPIO85-
GPIO95 bits within GEDR2 will also be masked out on PXA25x
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
move the GPIO IRQ initialization code to pxa_init_irq_gpio()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. move low IRQ initialization code to pxa_init_irq_low()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. define PXA_GPIO_IRQ_BASE to be right after the internal IRQs,
and define PXA_GPIO_IRQ_NUM to be 128 for all PXA2xx variants
2. make the code specific to the high IRQ numbers (32..64) to be
PXA27x specific
3. add a function pxa_init_irq_high() to initialize the internal
high IRQ chip, the invoke of this function could be moved to
PXA27x specific initialization code
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. PXA_IRQ_SKIP is defined to be 7 on PXA25x so that the first IRQ
starts from zero. This makes IRQ numbering inconsistent between
PXA25x and PXA27x. Remove this macro so that the same IRQ_XXXXX
definition has the same value on both PXA25x and PXA27x.
2. make IRQ_SSP3..IRQ_PWRI2C valid only if PXA27x is defined, this
avoids unintentional use of these macros on PXA25x
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Daniel Mack