Intel CPUID on AMD host or vice versa is a weird case, but it can
happen. Handle it by checking the host CPU vendor instead of the
guest's in reset_tdp_shadow_zero_bits_mask. For speed, the
check uses the fact that Intel EPT has an X (executable) bit while
AMD NPT has NX.
Reported-by: Borislav Petkov <bp@alien8.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_set_cr0 may want to call kvm_zap_gfn_range and thus access the
memslots array (SRCU protected). Using a mini SRCU critical section
is ugly, and adding it to kvm_arch_vcpu_create doesn't work because
the VMX vcpu_create callback calls synchronize_srcu.
Fixes this lockdep splat:
===============================
[ INFO: suspicious RCU usage. ]
4.3.0-rc1+ #1 Not tainted
-------------------------------
include/linux/kvm_host.h:488 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
1 lock held by qemu-system-i38/17000:
#0: (&(&kvm->mmu_lock)->rlock){+.+...}, at: kvm_zap_gfn_range+0x24/0x1a0 [kvm]
[...]
Call Trace:
dump_stack+0x4e/0x84
lockdep_rcu_suspicious+0xfd/0x130
kvm_zap_gfn_range+0x188/0x1a0 [kvm]
kvm_set_cr0+0xde/0x1e0 [kvm]
init_vmcb+0x760/0xad0 [kvm_amd]
svm_create_vcpu+0x197/0x250 [kvm_amd]
kvm_arch_vcpu_create+0x47/0x70 [kvm]
kvm_vm_ioctl+0x302/0x7e0 [kvm]
? __lock_is_held+0x51/0x70
? __fget+0x101/0x210
do_vfs_ioctl+0x2f4/0x560
? __fget_light+0x29/0x90
SyS_ioctl+0x4c/0x90
entry_SYSCALL_64_fastpath+0x16/0x73
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Russell King says:
====================
Phy, mdiobus, and netdev struct device fixes
The third version of this series fixes the build error which David
identified, and drops the broken changes for the Cavium Thunger BGX
ethernet driver as this driver requires some complex changes to
resolve the leakage - and this is best done by people who can test
the driver.
Compared to v2, the only patch which has changed is patch 6
"net: fix phy refcounting in a bunch of drivers"
I _think_ I've been able to build-test all the drivers touched by
that patch to some degree now, though several of them needed the
Kconfig hacked to allow it (not all had || COMPILE_TEST clause on
their dependencies.)
Previous cover letters below:
This is the second version of the series, with the comments David had
on the first patch fixed up. Original series description with updated
diffstat below.
While looking at the DSA code, I noticed we have a
of_find_net_device_by_node(), and it looks like users of that are
similarly buggy - it looks like net/dsa/dsa.c is the only user. Fix
that too.
Hi,
While looking at the phy code, I identified a number of weaknesses
where refcounting on device structures was being leaked, where
modules could be removed while in-use, and where the fixed-phy could
end up having unintended consequences caused by incorrect calls to
fixed_phy_update_state().
This patch series resolves those issues, some of which were discovered
with testing on an Armada 388 board. Not all patches are fully tested,
particularly the one which touches several network drivers.
When resolving the struct device refcounting problems, several different
solutions were considered before settling on the implementation here -
one of the considerations was to avoid touching many network drivers.
The solution here is:
phy_attach*() - takes a refcount
phy_detach*() - drops the phy_attach refcount
Provided drivers always attach and detach their phys, which they should
already be doing, this should change nothing, even if they leak a refcount.
of_phy_find_device() and of_* functions which use that take
a refcount. Arrange for this refcount to be dropped once
the phy is attached.
This is the reason why the previous change is important - we can't drop
this refcount taken by of_phy_find_device() until something else holds
a reference on the device. This resolves the leaked refcount caused by
using of_phy_connect() or of_phy_attach().
Even without the above changes, these drivers are leaking by calling
of_phy_find_device(). These drivers are addressed by adding the
appropriate release of that refcount.
The mdiobus code also suffered from the same kind of leak, but thankfully
this only happened in one place - the mdio-mux code.
I also found that the try_module_get() in the phy layer code was utterly
useless: phydev->dev.driver was guaranteed to always be NULL, so
try_module_get() was always being called with a NULL argument. I proved
this with my SFP code, which declares its own MDIO bus - the module use
count was never incremented irrespective of how I set the MDIO bus up.
This allowed the MDIO bus code to be removed from the kernel while there
were still PHYs attached to it.
One other bug was discovered: while using in-band-status with mvneta, it
was found that if a real phy is attached with in-band-status enabled,
and another ethernet interface is using the fixed-phy infrastructure, the
interface using the fixed-phy infrastructure is configured according to
the other interface using the in-band-status - which is caused by the
fixed-phy code not verifying that the phy_device passed in is actually
a fixed-phy device, rather than a real MDIO phy.
Lastly, having mdio_bus reversing phy_device_register() internals seems
like a layering violation - it's trivial to move that code to the phy
device layer.
====================
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_find_net_device_by_node() uses class_find_device() internally to
lookup the corresponding network device. class_find_device() returns
a reference to the embedded struct device, with its refcount
incremented.
Add a comment to the definition in net/core/net-sysfs.c indicating the
need to drop this refcount, and fix the DSA code to drop this refcount
when the OF-generated platform data is cleaned up and freed. Also
arrange for the ref to be dropped when handling errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phy_device_remove() function to complement phy_device_register(),
which undoes the effects of phy_device_register() by removing the phy
device from visibility, but not freeing it.
This allows these details to be moved out of the mdio bus code into
the phy code where this action belongs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate that the phy_device passed into fixed_phy_update_state() is a
fixed-phy device before walking the list of phys for a fixed phy at the
same address.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_find_device() increments the phy struct device refcount, which
we need to properly balance. Add code to network drivers using this
function to ensure that the struct device refcount is correctly
balanced.
For xgene, looking back in the history, we should be able to use
of_phy_connect() with a zero flags argument for the DT case as this is
how the driver used to operate prior to de7b5b3d79 ("net: eth: xgene:
change APM X-Gene SoC platform ethernet to support ACPI").
This leaves the Cavium Thunder BGX unfixed; fixing this driver is a
complicated task, one which the maintainers need to be involved with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
bus_find_device() is defined as:
* This is similar to the bus_for_each_dev() function above, but it
* returns a reference to a device that is 'found' for later use, as
* determined by the @match callback.
and it does indeed return a reference-counted pointer to the device:
while ((dev = next_device(&i)))
if (match(dev, data) && get_device(dev))
^^^^^^^^^^^^^^^
break;
klist_iter_exit(&i);
return dev;
What that means is that when we're done with the struct device, we must
drop that reference. Neither of_phy_connect() nor of_phy_attach() did
this when phy_connect_direct() or phy_attach_direct() failed.
With our previous patch, phy_connect_direct() and phy_attach_direct()
take a new refcount on the phy device when successful, so we can drop
our local reference immediatley after these functions, whether or not
they succeeded.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take a refcount on the phy struct device when the phy device is attached
to a network device, and drop it after it's detached. This ensures that
a refcount is held on the phy device while the device is being used by
a network device, thereby preventing the phy_device from being
unexpectedly kfree()'d by phy_device_release().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-implement the mdiobus module refcounting to ensure that we actually
ensure that the mdiobus module code does not go away while we might call
into it.
The old scheme using bus->dev.driver was buggy, because bus->dev is a
class device which never has a struct device_driver associated with it,
and hence the associated code trying to obtain a refcount did nothing
useful.
Instead, take the approach that other subsystems do: pass the module
when calling mdiobus_register(), and record that in the mii_bus struct.
When we need to increment the module use count in the phy code, use
this stored pointer. When the phy is deteched, drop the module
refcount, remembering that the phy device might go away at that point.
This doesn't stop the mii_bus going away while there are in-use phys -
it merely stops the underlying code vanishing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current users of of_mdio_find_bus() leak a struct device refcount, as
they fail to clean up the reference obtained inside class_find_device().
Fix the DSA code to properly refcount the returned MDIO bus by:
1. taking a reference on the struct device whenever we assign it to
pd->chip[x].host_dev.
2. dropping the reference when we overwrite the existing reference.
3. dropping the reference when we free the data structure.
4. dropping the initial reference we obtained after setting up the
platform data structure, or on failure.
In step 2 above, where we obtain a new MDIO bus, there is no need to
take a reference on it as we would only have to drop it immediately
after assignment again, iow:
put_device(cd->host_dev); /* drop original assignment ref */
cd->host_dev = get_device(&mdio_bus_switch->dev); /* get our ref */
put_device(&mdio_bus_switch->dev); /* drop of_mdio_find_bus ref */
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_mdio_find_bus() leaks a struct device refcount, caused by using
class_find_device() and not realising that the device reference has
its refcount incremented:
* Note, you will need to drop the reference with put_device() after use.
...
while ((dev = class_dev_iter_next(&iter))) {
if (match(dev, data)) {
get_device(dev);
break;
}
Update the comment, and arrange for the phy code to drop this refcount
when disposing of a reference to it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
switchdev: transaction item queue and cleanup
====================
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, since we have only 2 values for transaction phase, just use bool.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enum is going to disappear, use the helpers instead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer used by drivers, as transaction queue with item destructors
takes care of abort phase internally in switchdev code. So kill it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shouldn't have been there in the first place. Now it is unused, kill it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from previously introduced transaction item queue infrastructure
and remove rocker specific transaction memory management.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There will be needed to have switchdev_trans available down in the call
chain, so propagate it instead of trans phase enum. This enum will be
removed anyway. Also, use prepare/commit phase check helpers to get
information about current phase of transaction.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers which should be used int attr_set/obj_add switchdev ops to
check the phase of transaction.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before it disappears completely, move transaction phase enum under
transaction structure and make attr/obj structures a bit cleaner.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, the memory allocation in prepare/commit state is done separatelly
in each driver (rocker). Introduce the similar mechanism in generic
switchdev code, in form of queue. That can be used not only for memory
allocations, but also for different items. Abort item destruction
is handled as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is temporary, name "trans" will be used for something else and
"trans_ph" will eventually disappear.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull thermal management fixes from Zhang Rui:
- Power allocator governor changes to allow binding on thermal zones
with missing power estimates information. From Javi Merino.
- Add compile test flags on thermal drivers that allow it without
producing compilation errors. From Eduardo Valentin.
- Fixes around memory allocation on cpu_cooling. From Javi Merino.
- Fix on db8500 cpufreq code to allow autoload. From Luis de
Bethencourt.
- Maintainer entries for cpu cooling device
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: power_allocator: exit early if there are no cooling devices
thermal: power_allocator: don't require tzp to be present for the thermal zone
thermal: power_allocator: relax the requirement of two passive trip points
thermal: power_allocator: relax the requirement of a sustainable_power in tzp
thermal: Add a function to get the minimum power
thermal: cpu_cooling: free power table on error or when unregistering
thermal: cpu_cooling: don't call kcalloc() under rcu_read_lock
thermal: db8500_cpufreq_cooling: Fix module autoload for OF platform driver
thermal: cpu_cooling: Add MAINTAINERS entry
thermal: ti-soc: Kconfig fix to avoid menu showing wrongly
thermal: ti-soc: allow compile test
thermal: qcom_spmi: allow compile test
thermal: exynos: allow compile test
thermal: armada: allow compile test
thermal: dove: allow compile test
thermal: kirkwood: allow compile test
thermal: rockchip: allow compile test
thermal: spear: allow compile test
thermal: hisi: allow compile test
thermal: Fix thermal_zone_of_sensor_register to match documentation
- Silence bogus warning for of_irq_parse_pci
- Fix typo in ARM idle-states binding doc and dts files
- Various minor binding documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWBI2/AAoJEMhvYp4jgsXi08cH/11S/92w1PLNmWCv4y7TXHQw
XTJi7/Hk+q6otV/FigXukdYClR17h/3mFyCKKXHrkAgy/AoSrvN/ABe0bLLoT2AQ
xh0Rx8F6vZwa6ro1MZcrn3ZxQkoJlNUhoIXtY84oSPWd1ernLOar6HonFiynCQQc
bDZo5zoLj6DBbSO+UpVvEQN57ogwPgFZ1hGDjJeyyH8c1755z2OVA+k8O0dwjmqW
Xav/7TO8bFEIbUnfWeKnVyK45qmJxHcTbn3nxUgYFQj3DMI2Hn86WEY4cg8QvTo+
SpdO1Aio6b9NSTNnpiSvPnc2MFNPFaWjiqm1w86w+PTm8oUT+p1V0OG/EE27fcY=
=VUfk
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- Silence bogus warning for of_irq_parse_pci
- Fix typo in ARM idle-states binding doc and dts files
- Various minor binding documentation updates
* tag 'devicetree-fixes-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Documentation: arm: Fix typo in the idle-states bindings examples
gpio: mention in DT binding doc that <name>-gpio is deprecated
of_pci_irq: Silence bogus "of_irq_parse_pci() failed ..." messages.
devicetree: bindings: Extend the bma180 bindings with bma250 info
of: thermal: Mark cooling-*-level properties optional
of: thermal: Fix inconsitency between cooling-*-state and cooling-*-level
Docs: dt: add #msi-cells to GICv3 ITS binding
of: add vendor prefix for Socionext Inc.
Currently error log messages in ip6_tnl_err are printed at 'warn'
level. This is different to other tunnel types which don't print
any messages. These log messages don't provide any information that
couldn't be deduced with networking tools. Also it can be annoying
to have one end of the tunnel go down and have the logs fill with
pointless messages such as "Path to destination invalid or inactive!".
This patch reduces the log level of these messages to 'dbg' level to
bring the visible behaviour into line with other tunnel types.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The idle-states bindings mandate that the entry-method string
in the idle-states node must be "psci" for ARM v8 64-bit systems,
but the examples in the bindings report a wrong entry-method string.
Owing to this typo, some dts in the kernel wrongly defined the
entry-method property, since they likely cut and pasted the example
definition without paying attention to the bindings definitions.
This patch fixes the typo in the DT idle states bindings examples and
respective dts in the kernel so that the bindings and related dts
files are made compliant.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Howard Chen <howard.chen@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
The gpiolib supports parsing DT properties of the form <name>-gpio but it
was only added for compatibility with older DT bindings that got it wrong
and should not be used in newer bindings.
The commit that added support for this was:
dd34c37aa3 ("gpio: of: Allow -gpio suffix for property names")
but didn't update the documentation to explain this so it's been a source
of confusion. So let's make this clear in the GPIO DT binding doc.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-23
This series contains updates to ixgbe only.
Mark provides all the changes in this series, first clears the destination
location for I2C data initially so that the received data will not be
corrupted by previous attempts. Then reduced the pauses/delays in the
PHY detection when no SFP is present by reducing the number of retires,
once an SFP is detected, the "normal" number of retries in PHY detection
will be used. Added support for X55EM_x SFP+ dual-speed, and fixed 1G and
10G link stability for X550EM_x by configuring the CS4227 correctly by
moving code to ixgbe_setup_mac_link_sfp_x550em(). Added functionality to
reset CS4227, since on some platforms the CS4227 does not initialize
properly. Next reduces the SFP polling rate, due to when an SFP is not
present, the I2C timeouts that result are very costly. So prevent the
SFP polling from being done more than once every two seconds. Added
support for I2C bus MUX. Fixed the setting of RDRXCTL register which
should fall through X540 and 82599, not 82598. In addition, added small
packet padding support in X550 by setting RDRXCTL.PSP when the driver is
in SRIOV mode. Fixed a known hardware issue where the PCI transactions
pending bit sticks high when there are pending transactions, so
workaround the issue by wait and then continue with our reset flow.
Added a new device ID for X550EM device with SFPs. Provided a fix with
the DCA setup, which was suggested by Alex Duyck <aduyck@mirantis.com>,
by making it so that we always set the relaxed ordering bits related to
the DCA registers even if DCA is not enbaled. Then moves the
configuration out of the ixgbe_down() and into ixgbe_configure() before
enabling the transmit and receive rings. This ensures that DCA is
configured correctly before starting the processing of packets.
Fixed VM-to-VM loopback mode which requires that FCRTH be set, but
the datasheets did not specify what the value should be. It has now
been determined that the correct value should be RXPBSIZE - (24*1024).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"Most of the GPU drivers people were at XDC last week, so I didn't get
much to send, so I let it rollover until this week.
Also Alex was away for 3 weeks so amdgpu/radeon got a bit more stuff
than usual in one go.
I've been trying to figure out some 4.2 issues with i915 still (that
are fixed in 4.3, but bisecting ends up in a merge commit). Hopefully
next week I or i915 people can work that out"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (46 commits)
drm: Allow also control clients to check the drm version
drm/vmwgfx: Fix uninitialized return in vmw_kms_helper_dirty()
drm/vmwgfx: Fix uninitialized return in vmw_cotable_unbind()
drm/layerscape: fix handling fsl_dcu_drm_plane_index result
drm/mgag200: Fix driver_load error handling
drm/mgag200: Fix error handling paths in fbdev driver
drm/qxl: only report first monitor as connected if we have no state
drm/radeon: add quirk for MSI R7 370
drm/amdgpu: Sprinkle drm_modeset_lock_all to appease locking checks
drm/radeon: Sprinkle drm_modeset_lock_all to appease locking checks
drm/amdgpu: sync ce and me with SWITCH_BUFFER(2)
drm/amdgpu: integer overflow in amdgpu_mode_dumb_create()
drm/amdgpu: info leak in amdgpu_gem_metadata_ioctl()
drm/amdgpu: integer overflow in amdgpu_info_ioctl()
drm/amdgpu: unwind properly in amdgpu_cs_parser_init()
drm/amdgpu: Fix max_vblank_count value for current display engines
drm/amdgpu: use kmemdup rather than duplicating its implementation
drm/amdgpu: fix UVD suspend and resume for VI APU
drm/amdgpu: fix the UVD suspend sequence order
drm/amdgpu: make UVD handle checking more strict
...
* VHT MCS mask array overrun, reported by Dan Carpenter
* reset CQM history to always get a notification, from Sara Sharon
-----BEGIN PGP SIGNATURE-----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=4Ui5
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two small fixes:
* VHT MCS mask array overrun, reported by Dan Carpenter
* reset CQM history to always get a notification, from Sara Sharon
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently error log messages in ip6gre_err are printed at 'warn'
level. This is different to most other tunnel types which don't
print any messages. These log messages don't provide any information
that couldn't be deduced with networking tools. Also it can be annoying
to have one end of the tunnel go down and have the logs fill with
pointless messages such as "Path to destination invalid or inactive!".
This patch reduces the log level of these messages to 'dbg' level to
bring the visible behaviour into line with other tunnel types.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
dump_rules returns skb length and not error.
But when family == AF_UNSPEC, the caller of dump_rules
assumes that it returns an error. Hence, when family == AF_UNSPEC,
we continue trying to dump on -EMSGSIZE errors resulting in
incorrect dump idx carried between skbs belonging to the same dump.
This results in fib rule dump always only dumping rules that fit
into the first skb.
This patch fixes dump_rules to return error so that we exit correctly
and idx is correctly maintained between skbs that are part of the
same dump.
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Renesas R8A7794 SoC support to the Renesas R-Car gen2 PCI driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
added PCI_DEV_FLAGS_VPD_REF_F0. Previously, we set the flag on every
non-zero function of quirked devices. If a function turned out to be
different from function 0, i.e., it had a different class, vendor ID, or
device ID, the flag remained set but we didn't make VPD accessible at all.
Flip this around so we only set PCI_DEV_FLAGS_VPD_REF_F0 for functions that
are identical to function 0, and allow regular VPD access for any other
functions.
[bhelgaas: changelog, stable tag]
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
Commit 932c435cab ("PCI: Add dev_flags bit to access VPD through function
0") passes PCI_SLOT(devfn) for the devfn parameter of pci_get_slot().
Generally this works because we're fairly well guaranteed that a PCIe
device is at slot address 0, but for the general case, including
conventional PCI, it's incorrect. We need to get the slot and then convert
it back into a devfn.
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
SR-IOV creates a virtual bus where bus->self is NULL. When we add VFs and
scan for an MSI domain, pci_set_bus_msi_domain() dereferences bus->self,
which causes a kernel NULL pointer dereference oops.
Scan up to the parent bus until we find a real bridge where we can get the
MSI domain.
[bhelgaas: changelog]
Fixes: 44aa0c657e ("PCI/MSI: Add hooks to populate the msi_domain field")
Tested-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Neal suggested to move sk_txhash init into tcp_create_openreq_child(),
called both from IPv4 and IPv6.
This opportunity was missed in commit 58d607d3e5 ("tcp: provide
skb->hash to synack packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a good amount of debugging, I found bnx2x was byte swaping
the 40 bytes of rss_key.
If we byte swap the key, then bnx2x generates hashes matching
MSDN specs as documented in (Verifying the RSS Hash Calculation)
https://msdn.microsoft.com/en-us/library/windows/hardware/ff571021%
28v=vs.85%29.aspx
It is mostly a non issue, unless we want to mix different NIC
in a host, and want consistent hashing among all of them, ie
if they all use the boot time generated rss key, or if some application
is choosing specific tuple(s) so that incoming traffic lands into known
rx queue(s).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fw filter uses tp->root==NULL to check if it is the old method,
so it doesn't need allocation at all in this case. This patch
reverts the offending commit and adds some comments for old
method to make it obvious.
Fixes: 33f8b9ecdb ("net_sched: move tp->root allocation into fw_init()")
Reported-by: Akshat Kakkar <akshat.1984@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge misc fixes from Andrew Morton:
"15 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
ocfs2/dlm: fix deadlock when dispatch assert master
membarrier: clean up selftest
vmscan: fix sane_reclaim helper for legacy memcg
lib/iommu-common.c: do not try to deref a null iommu->lazy_flush() pointer when n < pool->hint
x86, efi, kasan: #undef memset/memcpy/memmove per arch
mm: migrate: hugetlb: putback destination hugepage to active list
mm, dax: VMA with vm_ops->pfn_mkwrite wants to be write-notified
userfaultfd: register uapi generic syscall (aarch64)
userfaultfd: selftest: don't error out if pthread_mutex_t isn't identical
userfaultfd: selftest: return an error if BOUNCE_VERIFY fails
userfaultfd: selftest: avoid my_bcmp false positives with powerpc
userfaultfd: selftest: only warn if __NR_userfaultfd is undefined
userfaultfd: selftest: headers fixup
userfaultfd: selftests: vm: pick up sanitized kernel headers
userfaultfd: revert "userfaultfd: waitqueue: add nr wake parameter to __wake_up_locked_key"
Jiri Benc says:
====================
lwtunnel: make it really work, for IPv4
One of the selling points of lwtunnel was the ability to specify the tunnel
destination using routes. However, this doesn't really work currently, as
ARP and ndisc replies are not handled correctly. ARP and ndisc replies won't
have tunnel metadata attached, thus they will be sent out with the default
parameters or not sent at all, either way never reaching the requester.
Most of the egress tunnel parameters can be inferred from the ingress
metada. The only and important exception is UDP ports. This patchset infers
the egress data from the ingress data and disallow settings of UDP ports in
tunnel routes. If there's a need for different UDP ports, a new interface
needs to be created for each port combination. Note that it's still possible
to specify the UDP ports to use, it just needs to be done while creating the
vxlan/geneve interface.
This covers only ARPs. IPv6 ndisc has the same problem but is harder to
solve, as there's already dst attached to outgoing skbs. Ideas to solve this
are welcome.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP tunnel config is asymmetric wrt. to the ports used. The source and
destination ports from one direction of the tunnel are not related to the
ports of the other direction. We need to be able to respond to ARP requests
using the correct ports without involving routing.
As the consequence, UDP ports need to be fixed property of the tunnel
interface and cannot be set per route. Remove the ability to set ports per
route. This is still okay to do, as no kernel has been released with these
attributes yet.
Note that the ability to specify source and destination ports is preserved
for other users of the lwtunnel API which don't use routes for tunnel key
specification (like openvswitch).
If in the future we rework ARP handling to allow port specification, the
attributes can be added back.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using ip lwtunnels, the additional data for xmit (basically, the actual
tunnel to use) are carried in ip_tunnel_info either in dst->lwtstate or in
metadata dst. When replying to ARP requests, we need to send the reply to
the same tunnel the request came from. This means we need to construct
proper metadata dst for ARP replies.
We could perform another route lookup to get a dst entry with the correct
lwtstate. However, this won't always ensure that the outgoing tunnel is the
same as the incoming one, and it won't work anyway for IPv4 duplicate
address detection.
The only thing to do is to "reverse" the ip_tunnel_info.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_read_u32 instead of of_get_property with return value
checks and endianness conversion.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_read_u32 to read the "clock-frequency" property instead
of using of_get_property with return value checks.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.
This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Kevin Hao <haokexin@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN device can receive skb with checksum partial. But the checksum
offset could be in outer header which is pulled on receive. This results
in negative checksum offset for the skb. Such skb can cause the assert
failure in skb_checksum_help(). Following patch fixes the bug by setting
checksum-none while pulling outer header.
Following is the kernel panic msg from old kernel hitting the bug.
------------[ cut here ]------------
kernel BUG at net/core/dev.c:1906!
RIP: 0010:[<ffffffff81518034>] skb_checksum_help+0x144/0x150
Call Trace:
<IRQ>
[<ffffffffa0164c28>] queue_userspace_packet+0x408/0x470 [openvswitch]
[<ffffffffa016614d>] ovs_dp_upcall+0x5d/0x60 [openvswitch]
[<ffffffffa0166236>] ovs_dp_process_packet_with_key+0xe6/0x100 [openvswitch]
[<ffffffffa016629b>] ovs_dp_process_received_packet+0x4b/0x80 [openvswitch]
[<ffffffffa016c51a>] ovs_vport_receive+0x2a/0x30 [openvswitch]
[<ffffffffa0171383>] vxlan_rcv+0x53/0x60 [openvswitch]
[<ffffffffa01734cb>] vxlan_udp_encap_recv+0x8b/0xf0 [openvswitch]
[<ffffffff8157addc>] udp_queue_rcv_skb+0x2dc/0x3b0
[<ffffffff8157b56f>] __udp4_lib_rcv+0x1cf/0x6c0
[<ffffffff8157ba7a>] udp_rcv+0x1a/0x20
[<ffffffff8154fdbd>] ip_local_deliver_finish+0xdd/0x280
[<ffffffff81550128>] ip_local_deliver+0x88/0x90
[<ffffffff8154fa7d>] ip_rcv_finish+0x10d/0x370
[<ffffffff81550365>] ip_rcv+0x235/0x300
[<ffffffff8151ba1d>] __netif_receive_skb+0x55d/0x620
[<ffffffff8151c360>] netif_receive_skb+0x80/0x90
[<ffffffff81459935>] virtnet_poll+0x555/0x6f0
[<ffffffff8151cd04>] net_rx_action+0x134/0x290
[<ffffffff810683d8>] __do_softirq+0xa8/0x210
[<ffffffff8162fe6c>] call_softirq+0x1c/0x30
[<ffffffff810161a5>] do_softirq+0x65/0xa0
[<ffffffff810687be>] irq_exit+0x8e/0xb0
[<ffffffff81630733>] do_IRQ+0x63/0xe0
[<ffffffff81625f2e>] common_interrupt+0x6e/0x6e
Reported-by: Anupam Chanda <achanda@vmware.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a few drm/i915 fixes, including a fix to the recent regression
reported by Sedat Dilek
* tag 'drm-intel-fixes-2015-09-24' of git://anongit.freedesktop.org/drm-intel:
drm/i915/bios: handle MIPI Sequence Block v3+ gracefully
drm/i915: Add primary plane to mask if it's visible
drm/i915: workaround bad DSL readout v3
drm/i915: fix kernel-doc warnings in intel_audio.c
inode_cgwb_enabled() gates cgroup writeback support. If it returns
true, each inode is attached to the corresponding memory domain which
gets mapped to io domain. It currently only tests whether the
filesystem and bdi support cgroup writeback; however, cgroup writeback
support doesn't work on traditional hierarchies and thus it should
also test whether memcg and iocg are on the default hierarchy.
This caused traditional hierarchy setups to hit the cgroup writeback
path inadvertently and ended up creating separate writeback domains
for each memcg and mapping them all to the root iocg uncovering a
couple issues in the cgroup writeback path.
cgroup writeback was never meant to be enabled on traditional
hierarchies. Make inode_cgwb_enabled() test whether both memcg and
iocg are on the default hierarchy.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Artem Bityutskiy <dedekind1@gmail.com>
Reported-by: Dexuan Cui <decui@microsoft.com>
Link: http://lkml.kernel.org/g/1443012552.19983.209.camel@gmail.com
Link: http://lkml.kernel.org/g/f30d4a6aa8a546ff88f73021d026a453@SIXPR30MB031.064d.mgd.msft.net
Paolo Bonzini