Fix problems with transmit pause frames. The driver was telling the
GMAC to flush (not process) pause frames. Manually disabling pause wasn't
working because of problems in the setup.
This maybe the cause of the lockup under load.
http://bugzilla.kernel.org/show_bug.cgi?id=6839
Patch against netdev-2.6 git tree
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement NAPI changes to pcnet32 driver. Compile default is off.
Listed as experimental.
Len and Don both worked on a NAPI implementation and have both tested
these changes.
An e1000 blasting short packets to the pcnet32 will lockup Don's system
until the receive storm stops. Without NAPI Len's system watchdog would
expire causing the system to reboot. With NAPI the system will stay
operational.
Tested ia32 and ppc64. Tested '970A, '971, '972, '973, '975, '976, and
'978.
The Kconfig changes came from Len. Don is to blame for all the others.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Breaking the receive frame processing into two routines for greater clarity.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move the receive routine and create the transmit routine.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change some magic numbers to clearer names. A few whitespace changes.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Delete unnecessary save/restore of rap in interrupt handler and statistics.
tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a missing call to dma_unmap_single() in the receive path. Without
this call, errors have been observed on non-cache-coherent systems.
Signed-off-by Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The commit 'e1000: Remove 0x1000 as supported device' (Jeff Kirsher,
673a052fde) Removes PIC device ID 8086:1000
from the list of supported devices. A fix was submitted for the original
issue (commit 6a9516989f).
This commit reverts commit 673a052fde and
re-enables 82542rev3 chips completely.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As long as the descriptor fits on a single cacheline, the change
should be almost free.
Now ring_info is not used at all. Remove it.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Commit 581d708eb4 (oct. 5 2005) introduced
partial Multiqueue support for e1000 which broke macro smartness in setting
up head/tail registers for 82542 rev3 chipsets, making these adapters
completely non-working since 2.6.15.
This commit sets the proper head and tail registers for read and write
descriptor rings. Ths fix was tested on an 82542 rev3 NIC and newer NICs.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As I promised last week, here is the first pass at removing all
unnecessary printk's that exist in network device drivers currently in
promiscuous mode. The duplicate messages are not needed so they have
been removed. Some of these drivers are quite old and might not need an
update, but I did them all anyway.
I am currently auditing the remaining conditional printk's and will send
out a patch for those soon.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hostap_cs driver
- added support for Proxim Harmony PCI W-Lan Card (uses pd6729 based
pcmcia2pci bridge)
Signed-off-by: Christian Steineck <memphis@machzwo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Coverity CID 1160 & 1161
Remove some dead code from bcm43xx_sysfs.c in 2.6.18-rc6
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch prints out the ucode debug status to sysfs. So, users can
watch the microcode status of their hardware.
Signed-off-by: Martin Langer <martin-langer@gmx.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch prints microcode revision, patchlevel, date and time to
KERN_INFO. Also, version 4.xx microcodes (rev>0x128) will be rejected
by the driver, because they still do not work.
Signed-off-by: Martin Langer <martin-langer@gmx.de>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes code that was make obsolete when the wireless
statistics in bcm43xx-softmac were changed, but was overlooked at that
time. The value of bcm->stats.link_quality computed here is never used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds bitrate information to the scan result in the Prism54
driver, like some/most other driver do.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inspired by an e-mail by Stephen Hemminger I decided to remove all
unneeded packed attributes from the code where the member variables are
already aligned. This avoids horrible code being generated on some
architectures.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Vincent TOUCHARD
zd1211 chip 0b05:170c v4802 high 00-11-d8 AL2230_RF pa0 g---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Martin Dummer.
zd1211 chip 0b3b:5630 v4330 high 00-01-e3 RF2959_RF pa0 ---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an out of sequence step in the bcm43xx_init_board
routine for bcm43xx-softmac.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes various bugs in the init and shutdown code
that would lead to lockups and crashes.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Caused by a documentation issue I mixed up fields of the zd_status
structure. This patch fixes it and improves also the average
computation, which is now using only measurements of packets sent
by the access point.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inverting the write ordering of the TxDescAddr{High/Low} registers
suffices to trigger a sabbat of PCI errors which make the device
completely dysfunctional. The issue has not been reported on a
different platform.
Switching from MMIO accesses to I/O ones as done in Realtek's
own driver fixes (papers over ?) the bug as well but I am not
thrilled to see everyone pay the I/O price for an obscure bug.
This is the minimal change to handle the issue.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
dm9000_release_board calls release_resource with the platform resource
instead of the requested resource:
db->addr_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
db->addr_req = request_mem_region(db->addr_res->start, i, pdev->name);
dm9000_release_board:
if (db->addr_res != NULL) {
release_resource(db->addr_res);
kfree(db->addr_req);
With this behavior the kernel will crash on the second removal. The
attached patch fix this problem.
Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This removes unnecessary messages that show up every time I put my
ethernet card in promiscuous mode. I'm already getting notification
from the networking layer, I don't need notification from the driver as
well.
There are probably other drivers that do this as well -- I'll look
around and see what I can find.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Include "tulip.h" in winbond-840.c and clean up lots of redundant
definitions.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update/cleanup some definitions in tulip.h and tulip_core.c.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move tulip_select_media() processing to a workqueue, instead of
delaying in interrupt context, edited by Kyle McMartin to use kevent
thread, instead of creating its own workqueue.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The obvious safe registers to read is one from PCI config space.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As the cookie returned by pci_iomap() is fairly useless...
[Compile warning on pci_resource_start() format fixed up by Valerie
Henson.]
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes the needlessly global e1000_phy_igp_get_info() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Because of the NAPI and other SMP fixes, let's call
this a version.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver has much better performance if transmit done is handled in
NAPI softirq. Change from doing transmit locking in driver (LLTX) and
use device lock.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver needs to access the IRQ status inside of lock to avoid
races with other places changing IRQ mask etc. This may be related
to some of the SMP bugs reported against skge in kernel bugzilla.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change to use new netdev_alloc_skb interface for 2.6.18.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some more Marvell device id's, these are from the latest SysKonnect
vendor driver version of sk98lin (8.36).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve the firmware selection by adding 2 cases where we should use the
optimized firmware:
* when the actual PCIe link width is lower than 8x.
* when the board is plugged to one of the new Intel PCIe chipsets that
are known to provide aligned PCIe completions.
The patch actually raises two concerns:
* We might want to add a generic PCI function to get the PCIe link width since
some other drivers (at least ipath) do the same. But we probably do not want
to add a new function for every PCIe capability. I will probably look at it
and discuss it on linux-pci in the future.
* As requested during the submission, the PCI ids of chipsets that are known to
provided aligned completion are defined in the myri10ge code. If we keep adding
new ones, it might become better to move them to pciids.h.
But, this sort of quirk to detect these chipsets are very specific to our NIC,
I don't think it is worth moving it to the PCI core until somebody else really
needs it.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the firmware download URL in Kconfig to match the header
in drivers/net/myri10ge/myri10ge.c.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch decouples the dependency between the rx checksum feature and
vlan feature. This is done by ignoring the checksum information if the
user has disabled rx checksum when vlan is enabled.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch addresses an errata found on certain marvell phys concerning
the reset of the BMCR phy register during phy reset.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adds PCI Error recovery callbacks to the Intel 10-gigabit ethernet ixgb
device driver. Lightly tested, works.
"Zhang, Yanmin" <yanmin_zhang@linux.intel.com> wrote:
Both pci_disable_device and ixgb_down would access the device. It doesn't
follow Documentation/pci-error-recovery.txt that error_detected shouldn't do
any access to the device.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
A recent patch in -mm3 titled
"gregkh-pci-pci-don-t-enable-device-if-already-enabled.patch" causes
pci_enable_device() to be a no-op if the kernel thinks that the device is
already enabled. This change breaks the PCI error recovery mechanism in
the e100 device driver, since, after PCI slot reset, the card is no longer
enabled. This is a trivial fix for this problem. Tested.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Device 0x10a4 is a double 82571 on a single PCI-Express card and
has 4 gigabit capable ports.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
WoL is constantly giving problems and needed a rewrite. Consolidates
all WoL capabilities into a single function, and disables WoL for all
other ports on the device except for port A.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
struct cp_private is reorganized to be more easily compared between the
r8169 and the 8139cp drivers.
The alignment should not be impacted.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The ring_info.len field is not used at all. cp_private.rx_skb is
turned into an array of sk_buff *.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
No need to chew CPU cycles as there is no heavy timing requirement
and the delays are always requested from a sleepable context.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The current probe table causes ledma and lebuffer
"le" devices to get probed twice which is not what
we want.
Match just "le" and look directly at the parent to get the correct
top-level node information.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found by inspection. The STRIP driver does neigh_lookup() but never
releases. This driver shouldn't being doing gratuitous arp anyway.
Untested, obviously, because of lack of hardware.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several people run into the situation where the E100
EEPROM contents are fine, but the checksum hasn't been
set properly. This renders the device useless for
them even though it would function correctly.
The default is off, which retains the current behavior.
Signed-off-by: David S. Miller <davem@davemloft.net>
The user level irq balance daemon uses "eth" as a way to distinquish
ethernet devices. Also, by using device name it is possible to distinquish
different boards.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To avoid problems with buggy protocols that assume extra header space,
use dev_alloc_skb() when allocating receive buffers.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At the end of a critical section, we need to force the PCI write
to complete by doing a read.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code for suspend/resume needs several fixes. The hardware lock
should be setup in probe only, not in resume. Interrupts should be
disabled during suspend, etc.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To save power, don't enable power to the PHY until device is brought up.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since many packets have the same checksum starting offset and insertion
location; the driver can save the last information and only tell hardware
when it changes.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The MSS in the transmit engine only has to change if TSO mtu changes. This
means less commands to the chip when mixing TSO and regular data.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The test for MSI IRQ could have timing issues. The PCI write needs to be
pushed out before waiting, and the wait queue should be initialized before
the IRQ.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't use force status bit. It was never implemented on all chips, or has
no impact.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use netdev_alloc_skb for buffer allocation to allow for headroom.
This prevents bugs in code paths that assume extra space at the
front and makes sky2 behave like other drivers.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code to handle cloned skb overwriting is unnecessary in the
sky2 driver and is buggy. The bug is that pskb_expand_head can change the
skb but the driver has already mapped in the header.
Since the sky2 hardware doesn't need to overwrite memory, the buggy
code can just be removed; it was mistakenly copied from the tg3
driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch sets the floor of wireless level (signal) and noise at
-110 dBm, which makes them be comatible with RCPI, as discussed by
Simon Barber. With this change, bcm43xx-softmac and bcm43xx-d80211
behave the same.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When bcm43xx-softmac is given an ifdown/ifup sequence, the value for
bcm->mac_suspended ends up wrong, which leads to a large number of
assert(bcm->mac_suspended>=0) messages. This one-line patch fixes
this problem.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables the ipw2200 driver to support passive scanning as
offered by the wireless extensions. For this, I enhanced the ipw_wx_set_scan
function in such a way that it differentiates between a passive and an
active scan request. Additionally, I added a new function called
ipw_request_passive_scan that is similiar to the ipw_request_scan
function to perform passive scans. Last but not least, I added a field
(in fact it is a work_struct struct) called request_passive_scan to
the ipw_priv struct.
Signed-off-by: Thomas King <king@informatik.uni-mannheim.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix by removing dependency between priv->action_sem and rtnl semaphore.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we don't disable the card in the pci .shutdown method, there might be
pending interrupts still in the interrupt line after a reboot on some
platform. This patch fixes the problem by disable the hardware in the pci
.shutdown method.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When command error log debug is enabled, we write every host command and
parameters into a buffer. But we didn't alloc the parameter buffer for this
case. The patch adds struct cmdlog_host_cmd so that the buffer is allocated
from the stack.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ipw2200 firmware/ucode only support values from 0 to 254. So mark 255
as invalid.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_RADIOTAP_TSFT is defined as the Value in microseconds of the
MAC's 64-bit 802.11 Time Synchronization Function timer when the first bit
of the MPDU arrived at the MAC. Since ipw2200 hardware doesn't provide this
value, we disable this feature from the radiotap header present flag.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch traps the case when the essid is being set to its
current value. If the essid is being set again and we are already
associated, chances are some other parameters have also been altered.
I think it is safer to do the re-association for this case.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleanups the ipw_wx_set_essid code and forces a reassociation
when setting the essid to "any". I have tested this patch with iwconfig. It
makes ipw2200 compliant with all the cases mentioned in the iwconfig man
page. The commands
iwconfig iface essid any
iwconfig iface essid -- any
iwconfig iface essid off
iwconfig iface essid on
all seemed to work correctly. None of this worked before the patch.
Note, this patch treats
iwconfig iface essid
iwconfig iface essid ""
The same. It produces an error message: essid: Unknown host.
Since an essid of "" is not mentioned in the iwconfig man page.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SIOCGIWFREQ ioctl fills the request structure's freq field by setting
the exponent to 0 and the mantissa to the current channel number. The
iwconfig tool works around this behaviour by looking up the frequency
from the channel table if a frequency below 1kHz is returned, other tools
(e.g. kwlaninfo) don't. According to the comment in the iwconfig source
the driver is supposed to return the frequency, not the channel number.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving part of the debugging code from IPW_DEBUG to IPW_LL_DEBUG (low level
debugging) and make IPW_DEBUG be always enabled. IPW_LL_DEBUG still needs
to be enabled by selecting CONFIG_IPW2200_DEBUG. But it is highly
deprecated for normal users since it adds higher debug verbosity in driver
hot paths.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hard_start_xmit should return a NETIF_TX_FOO error code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert the bitfields in the bcm43xx DMA code to properly
aligned u8 booleans. These flags are accessed in the DMA
hotpath, so it's a good idea to waste a few bytes of memory
for the sake of speed by not requiring masking (and probably
shifting) of the bitfields.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't rely on linux/if_arp.h being included by other headers
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SPARC architecture has been fixed, so it's no longer needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calls to bcm43xx_rng_init() and bcm43xx_rng_exit() got
lost due to merge trouble. Re-add them.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a rewrite of the bcm43xx DMA engine. It adds support
for >1G of memory (for chips that support the extension bits)
and 64-bit DMA (for chips that support it).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The airo driver is currently caching a pid for later use, but with the
implementation of containers, pids themselves do not uniquely identify a
task. The driver is also using kernel_thread() which is deprecated in
drivers.
This patch essentially replaces the kernel_thread() with kthread_create().
It also stores the task_struct of the airo_thread rather than its pid.
Since this introduces a second task_struct in struct airo_info, the patch
renames airo_info.task to airo_info.list_bss_task.
As an extension of these changes, the patch further:
- replaces kill_proc() with kthread_stop()
- replaces signal_pending() with kthread_should_stop()
- removes thread completion synchronisation which is handled by
kthread_stop().
[akpm@osdl.org: fix races]
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Javier Achirica <achirica@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the code that reads part_num from the EEPROM. This part number
is never displayed or queryable by the user.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Memory leak was found in 2.6.18-rc4 and e1000 7.2.7 from sourceforge: We
should free resources allocated for previous rings if following allocation
fails.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
irq leak was found in 2.6.18-rc4 and e1000 7.2.7 from sourceforge: if
e1000_up fails in e1000_open() we do not free allocated irq
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Some recent myri10ge firmwares support multicast filtering as well
as an extended mcp_irq_data structure (64 instead of 40 bytes).
The new command MXGEFW_CMD_SET_STATS_DMA_V2 is used to check
whether the firmware support those. mgp->fw_multicast_support
is defined accordingly.
When fw_multicast_support is set, some new multicast filtering
commands is passed to the board in myri10ge_set_multicast_list().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add msg_enable and use netif_msg_link to enable/disable reporting
of link status changes since some Ethernet switches seem to generate
a lot of status changes under some circumstances and some people
want to avoid useless flooding in the logs.
Also add a counter for link status changes to statistics.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
spectrum_cs: Fix the logic so we error when the device is *not* present!
This fixes firmware upload failures which prevent the driver from
working (the bug is also present in 2.6.17).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A change I made for 2.6.17 and another for 2.6.18 do not work on older
pcnet32 chips which I do not have access to. If the chip is a 79C970 or
79C965, do not try and suspend or check the link status.
I have tested with a 79C970A, 79C971, 79C972, 79C973, 79C975, 79C976,
and 79C978.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I am using a Xircom CEM33 pcmcia NIC which has occasional hardware problems.
If the netdev watchdog detects a transmit timeout, do_reset is called which
msleeps - this is illegal in atomic context.
This patch schedules the timeout handling as a workqueue item.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
