[ Upstream commit 937d842058 ]
The current code sets up the filter action field before
rewrites are set up. When the action 'switch' is used
with rewrites, this may result in initial few packets
that get switched out don't have rewrites applied
on them.
So, make sure filter action is set up along with rewrites
or only after everything else is set up for rewrites.
Fixes: 12b276fbf6 ("cxgb4: add support to create hash filters")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Link: https://lore.kernel.org/r/20201023115852.18262-1-rajur@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f3391ce8f ]
chtls_pt_recvmsg() receives a skb with tls header and subsequent
skb with data, need to finalize the data copy whenever next skb
with tls header is available. but here current tls header is
overwritten by next available tls header, ends up corrupting
user buffer data. fixing it by finalizing current record whenever
next skb contains tls header.
v1->v2:
- Improved commit message.
Fixes: 17a7d24aa8 ("crypto: chtls - generic handling of data and hdr")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Link: https://lore.kernel.org/r/20201022190556.21308-1-vinay.yadav@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 28e9dcd917 ]
In chtls_pass_establish() we hold child socket lock using bh_lock_sock
and we are again trying bh_lock_sock in add_to_reap_list, causing deadlock.
Remove bh_lock_sock in add_to_reap_list() as lock is already held.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Link: https://lore.kernel.org/r/20201025193538.31112-1-vinay.yadav@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 825741b071 ]
In the AER or firmware reset flow, if we are in fatal error state or
if pci_channel_offline() is true, we don't send any commands to the
firmware because the commands will likely not reach the firmware and
most commands don't matter much because the firmware is likely to be
reset imminently.
However, the HWRM_FUNC_RESET command is different and we should always
attempt to send it. In the AER flow for example, the .slot_reset()
call will trigger this fw command and we need to try to send it to
effect the proper reset.
Fixes: b340dc680e ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 336af6a468 upstream.
Without this patch efivarfs_alloc_dentry creates dentries with slashes in
their name if the respective EFI variable has slashes in its name. This in
turn causes EIO on getdents64, which prevents a complete directory listing
of /sys/firmware/efi/efivars/.
This patch replaces the invalid shlashes with exclamation marks like
kobject_set_name_vargs does for /sys/firmware/efi/vars/ to have consistently
named dentries under /sys/firmware/efi/vars/ and /sys/firmware/efi/efivars/.
Signed-off-by: Michael Schaller <misch@google.com>
Link: https://lore.kernel.org/r/20200925074502.150448-1-misch@google.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 035fff1f7a upstream.
Fix build error when CONFIG_ACPI is not set/enabled by adding the header
file <asm/acpi.h> which contains a stub for the function in the build
error.
../arch/x86/pci/intel_mid_pci.c: In function ‘intel_mid_pci_init’:
../arch/x86/pci/intel_mid_pci.c:303:2: error: implicit declaration of function ‘acpi_noirq_set’; did you mean ‘acpi_irq_get’? [-Werror=implicit-function-declaration]
acpi_noirq_set();
Fixes: a912a7584e ("x86/platform/intel-mid: Move PCI initialization to arch_init()")
Link: https://lore.kernel.org/r/ea903917-e51b-4cc9-2680-bc1e36efa026@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jesse Barnes <jsbarnes@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # v4.16+
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jsbarnes@google.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b92fa7485 upstream.
With CONFIG_EXPERT=y, CONFIG_KASAN=y, CONFIG_RANDOMIZE_BASE=n,
CONFIG_RELOCATABLE=n, we observe the following failure when trying to
link the kernel image with LD=ld.lld:
error: section: .exit.data is not contiguous with other relro sections
ld.lld defaults to -z relro while ld.bfd defaults to -z norelro. This
was previously fixed, but only for CONFIG_RELOCATABLE=y.
Fixes: 3bbd3db864 ("arm64: relocatable: fix inconsistencies in linker script and options")
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201016175339.2429280-1-ndesaulniers@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39533e1206 upstream.
Commit 606f8e7b27 ("arm64: capabilities: Use linear array for
detection and verification") changed the way we deal with per-CPU errata
by only calling the .matches() callback until one CPU is found to be
affected. At this point, .matches() stop being called, and .cpu_enable()
will be called on all CPUs.
This breaks the ARCH_WORKAROUND_2 handling, as only a single CPU will be
mitigated.
In order to address this, forcefully call the .matches() callback from a
.cpu_enable() callback, which brings us back to the original behaviour.
Fixes: 606f8e7b27 ("arm64: capabilities: Use linear array for detection and verification")
Cc: <stable@vger.kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18fce56134 upstream.
Commit 73f3816609 ("arm64: Advertise mitigation of Spectre-v2, or lack
thereof") changed the way we deal with ARCH_WORKAROUND_1, by moving most
of the enabling code to the .matches() callback.
This has the unfortunate effect that the workaround gets only enabled on
the first affected CPU, and no other.
In order to address this, forcefully call the .matches() callback from a
.cpu_enable() callback, which brings us back to the original behaviour.
Fixes: 73f3816609 ("arm64: Advertise mitigation of Spectre-v2, or lack thereof")
Cc: <stable@vger.kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 548b8b5168 upstream.
When building for an embedded target using Yocto, we're sometimes
observing that the version string that gets built into vmlinux (and
thus what uname -a reports) differs from the path under /lib/modules/
where modules get installed in the rootfs, but only in the length of
the -gabc123def suffix. Hence modprobe always fails.
The problem is that Yocto has the concept of "sstate" (shared state),
which allows different developers/buildbots/etc. to share build
artifacts, based on a hash of all the metadata that went into building
that artifact - and that metadata includes all dependencies (e.g. the
compiler used etc.). That normally works quite well; usually a clean
build (without using any sstate cache) done by one developer ends up
being binary identical to a build done on another host. However, one
thing that can cause two developers to end up with different builds
[and thus make one's vmlinux package incompatible with the other's
kernel-dev package], which is not captured by the metadata hashing, is
this `git describe`: The output of that can be affected by
(1) git version: before 2.11 git defaulted to a minimum of 7, since
2.11 (git.git commit e6c587) the default is dynamic based on the
number of objects in the repo
(2) hence even if both run the same git version, the output can differ
based on how many remotes are being tracked (or just lots of local
development branches or plain old garbage)
(3) and of course somebody could have a core.abbrev config setting in
~/.gitconfig
So in order to avoid `uname -a` output relying on such random details
of the build environment which are rather hard to ensure are
consistent between developers and buildbots, make sure the abbreviated
sha1 always consists of exactly 12 hex characters. That is consistent
with the current rule for -stable patches, and is almost always enough
to identify the head commit unambigously - in the few cases where it
does not, the v5.4.3-00021- prefix would certainly nail it down.
[Adapt to `` vs $() differences between 5.4 and upstream.]
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e81e072443 upstream.
When compiling the kernel with AS=clang, objtool produces a lot of
warnings:
warning: objtool: missing symbol for section .text
warning: objtool: missing symbol for section .init.text
warning: objtool: missing symbol for section .ref.text
It then fails to generate the ORC table.
The problem is that objtool assumes text section symbols always exist.
But the Clang assembler is aggressive about removing them.
When generating relocations for the ORC table, objtool always tries to
reference instructions by their section symbol offset. If the section
symbol doesn't exist, it bails.
Do a fallback: when a section symbol isn't available, reference a
function symbol instead.
Reported-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://github.com/ClangBuiltLinux/linux/issues/669
Link: https://lkml.kernel.org/r/9a9cae7fcf628843aabe5a086b1a3c5bf50f42e8.1585761021.git.jpoimboe@redhat.com
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e3bbb33e6 upstream.
SOCK_TSTAMP_NEW (timespec64 instead of timespec) is also used for
hardware time stamps (configured via SO_TIMESTAMPING_NEW).
User space (ptp4l) first configures hardware time stamping via
SO_TIMESTAMPING_NEW which sets SOCK_TSTAMP_NEW. In the next step, ptp4l
disables SO_TIMESTAMPNS(_NEW) (software time stamps), but this must not
switch hardware time stamps back to "32 bit mode".
This problem happens on 32 bit platforms were the libc has already
switched to struct timespec64 (from SO_TIMExxx_OLD to SO_TIMExxx_NEW
socket options). ptp4l complains with "missing timestamp on transmitted
peer delay request" because the wrong format is received (and
discarded).
Fixes: 887feae36a ("socket: Add SO_TIMESTAMP[NS]_NEW")
Fixes: 783da70e83 ("net: add sock_enable_timestamps")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31cc578ae2 upstream.
This patch fixes the issue due to:
BUG: KASAN: slab-out-of-bounds in nft_flow_rule_create+0x622/0x6a2
net/netfilter/nf_tables_offload.c:40
Read of size 8 at addr ffff888103910b58 by task syz-executor227/16244
The error happens when expr->ops is accessed early on before performing the boundary check and after nft_expr_next() moves the expr to go out-of-bounds.
This patch checks the boundary condition before expr->ops that fixes the slab-out-of-bounds Read issue.
Add nft_expr_more() and use it to fix this problem.
Signed-off-by: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7974ecd7d3 ]
Currently, enabling f_ncm at SuperSpeed Plus speeds results in an
oops in config_ep_by_speed because ncm_set_alt passes in NULL
ssp_descriptors. Fix this by re-using the SuperSpeed descriptors.
This is safe because usb_assign_descriptors calls
usb_copy_descriptors.
Tested: enabled f_ncm on a dwc3 gadget and 10Gbps link, ran iperf
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 37d2a36394 upstream.
syzbot is reporting hung task at wdm_flush() [1], for there is a circular
dependency that wdm_flush() from flip_close() for /dev/cdc-wdm0 forever
waits for /dev/raw-gadget to be closed while close() for /dev/raw-gadget
cannot be called unless close() for /dev/cdc-wdm0 completes.
Tetsuo Handa considered that such circular dependency is an usage error [2]
which corresponds to an unresponding broken hardware [3]. But Alan Stern
responded that we should be prepared for such hardware [4]. Therefore,
this patch changes wdm_flush() to use wait_event_interruptible_timeout()
which gives up after 30 seconds, for hardware that remains silent must be
ignored. The 30 seconds are coming out of thin air.
Changing wait_event() to wait_event_interruptible_timeout() makes error
reporting from close() syscall less reliable. To compensate it, this patch
also implements wdm_fsync() which does not use timeout. Those who want to
be very sure that data has gone out to the device are now advised to call
fsync(), with a caveat that fsync() can return -EINVAL when running on
older kernels which do not implement wdm_fsync().
This patch also fixes three more problems (listed below) found during
exhaustive discussion and testing.
Since multiple threads can concurrently call wdm_write()/wdm_flush(),
we need to use wake_up_all() whenever clearing WDM_IN_USE in order to
make sure that all waiters are woken up. Also, error reporting needs
to use fetch-and-clear approach in order not to report same error for
multiple times.
Since wdm_flush() checks WDM_DISCONNECTING, wdm_write() should as well
check WDM_DISCONNECTING.
In wdm_flush(), since locks are not held, it is not safe to dereference
desc->intf after checking that WDM_DISCONNECTING is not set [5]. Thus,
remove dev_err() from wdm_flush().
[1] https://syzkaller.appspot.com/bug?id=e7b761593b23eb50855b9ea31e3be5472b711186
[2] https://lkml.kernel.org/r/27b7545e-8f41-10b8-7c02-e35a08eb1611@i-love.sakura.ne.jp
[3] https://lkml.kernel.org/r/79ba410f-e0ef-2465-b94f-6b9a4a82adf5@i-love.sakura.ne.jp
[4] https://lkml.kernel.org/r/20200530011040.GB12419@rowland.harvard.edu
[5] https://lkml.kernel.org/r/c85331fc-874c-6e46-a77f-0ef1dc075308@i-love.sakura.ne.jp
Reported-by: syzbot <syzbot+854768b99f19e89d7f81@syzkaller.appspotmail.com>
Cc: stable <stable@vger.kernel.org>
Co-developed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928141755.3476-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29788ab1d2 upstream.
The watermark is set to 1, so we need to input two chars to trigger RDRF
using the original logic. With the new logic, we could always get the
char when there is data in FIFO.
Suggested-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a04f0ecacd ]
The only time that our Bridgeport role should change is when we change
the configuration ourselves. In which case we also adjust our internal
state tracking, no need to do it again when we receive the corresponding
event.
Removing the locked section helps a subsequent patch that needs to flush
the workqueue while under sbp_lock.
It would be nice to raise a warning here in case HW does weird things
after all, but this could end up generating false-positives when we
change the configuration ourselves.
Suggested-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bad60b8d1a ]
The idx in __ath10k_htt_rx_ring_fill_n function lives in
consistent dma region writable by the device. Malfunctional
or malicious device could manipulate such idx to have a OOB
write. Either by
htt->rx_ring.netbufs_ring[idx] = skb;
or by
ath10k_htt_set_paddrs_ring(htt, paddr, idx);
The idx can also be negative as it's signed, giving a large
memory space to write to.
It's possibly exploitable by corruptting a legit pointer with
a skb pointer. And then fill skb with payload as rougue object.
Part of the log here. Sometimes it appears as UAF when writing
to a freed memory by chance.
[ 15.594376] BUG: unable to handle page fault for address: ffff887f5c1804f0
[ 15.595483] #PF: supervisor write access in kernel mode
[ 15.596250] #PF: error_code(0x0002) - not-present page
[ 15.597013] PGD 0 P4D 0
[ 15.597395] Oops: 0002 [#1] SMP KASAN PTI
[ 15.597967] CPU: 0 PID: 82 Comm: kworker/u2:2 Not tainted 5.6.0 #69
[ 15.598843] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[ 15.600438] Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
[ 15.601389] RIP: 0010:__ath10k_htt_rx_ring_fill_n
(linux/drivers/net/wireless/ath/ath10k/htt_rx.c:173) ath10k_core
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200623221105.3486-1-bruceshenzk@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d9459d040 ]
CFGx.FIFO_MODE field controls a DMA-controller "FIFO readiness" criterion.
In other words it determines when to start pushing data out of a DW
DMAC channel FIFO to a destination peripheral or from a source
peripheral to the DW DMAC channel FIFO. Currently FIFO-mode is set to one
for all DW DMAC channels. It means they are tuned to flush data out of
FIFO (to a memory peripheral or by accepting the burst transaction
requests) when FIFO is at least half-full (except at the end of the block
transfer, when FIFO-flush mode is activated) and are configured to get
data to the FIFO when it's at least half-empty.
Such configuration is a good choice when there is no slave device involved
in the DMA transfers. In that case the number of bursts per block is less
than when CFGx.FIFO_MODE = 0 and, hence, the bus utilization will improve.
But the latency of DMA transfers may increase when CFGx.FIFO_MODE = 1,
since DW DMAC will wait for the channel FIFO contents to be either
half-full or half-empty depending on having the destination or the source
transfers. Such latencies might be dangerous in case if the DMA transfers
are expected to be performed from/to a slave device. Since normally
peripheral devices keep data in internal FIFOs, any latency at some
critical moment may cause one being overflown and consequently losing
data. This especially concerns a case when either a peripheral device is
relatively fast or the DW DMAC engine is relatively slow with respect to
the incoming data pace.
In order to solve problems, which might be caused by the latencies
described above, let's enable the FIFO half-full/half-empty "FIFO
readiness" criterion only for DMA transfers with no slave device involved.
Thanks to the commit 99ba8b9b0d ("dmaengine: dw: Initialize channel
before each transfer") we can freely do that in the generic
dw_dma_initialize_chan() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731200826.9292-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8ee6c8cb6 ]
DW DMA IP-core provides a way to synthesize the DMA controller with
channels having different parameters like maximum burst-length,
multi-block support, maximum data width, etc. Those parameters both
explicitly and implicitly affect the channels performance. Since DMA slave
devices might be very demanding to the DMA performance, let's provide a
functionality for the slaves to be assigned with DW DMA channels, which
performance according to the platform engineer fulfill their requirements.
After this patch is applied it can be done by passing the mask of suitable
DMA-channels either directly in the dw_dma_slave structure instance or as
a fifth cell of the DMA DT-property. If mask is zero or not provided, then
there is no limitation on the channels allocation.
For instance Baikal-T1 SoC is equipped with a DW DMAC engine, which first
two channels are synthesized with max burst length of 16, while the rest
of the channels have been created with max-burst-len=4. It would seem that
the first two channels must be faster than the others and should be more
preferable for the time-critical DMA slave devices. In practice it turned
out that the situation is quite the opposite. The channels with
max-burst-len=4 demonstrated a better performance than the channels with
max-burst-len=16 even when they both had been initialized with the same
settings. The performance drop of the first two DMA-channels made them
unsuitable for the DW APB SSI slave device. No matter what settings they
are configured with, full-duplex SPI transfers occasionally experience the
Rx FIFO overflow. It means that the DMA-engine doesn't keep up with
incoming data pace even though the SPI-bus is enabled with speed of 25MHz
while the DW DMA controller is clocked with 50MHz signal. There is no such
problem has been noticed for the channels synthesized with
max-burst-len=4.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200731200826.9292-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89dd87acd4 ]
If ufs_qcom_dump_dbg_regs() calls ufs_qcom_testbus_config() from
ufshcd_suspend/resume and/or clk gate/ungate context, pm_runtime_get_sync()
and ufshcd_hold() will cause a race condition. Fix this by removing the
unnecessary calls of pm_runtime_get_sync() and ufshcd_hold().
Link: https://lore.kernel.org/r/1596975355-39813-3-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbc299437c ]
usb_kill_anchored_urbs() is commonly used to cancel all URBs on an
anchor just before releasing resources which the URBs rely on. By doing
so, users of this function rely on that no completer callbacks will take
place from any URB on the anchor after it returns.
However if this function is called in parallel with __usb_hcd_giveback_urb
processing a URB on the anchor, the latter may call the completer
callback after usb_kill_anchored_urbs() returns. This can lead to a
kernel panic due to use after release of memory in interrupt context.
The race condition is that __usb_hcd_giveback_urb() first unanchors the URB
and then makes the completer callback. Such URB is hence invisible to
usb_kill_anchored_urbs(), allowing it to return before the completer has
been called, since the anchor's urb_list is empty.
Even worse, if the racing completer callback resubmits the URB, it may
remain in the system long after usb_kill_anchored_urbs() returns.
Hence list_empty(&anchor->urb_list), which is used in the existing
while-loop, doesn't reliably ensure that all URBs of the anchor are gone.
A similar problem exists with usb_poison_anchored_urbs() and
usb_scuttle_anchored_urbs().
This patch adds an external do-while loop, which ensures that all URBs
are indeed handled before these three functions return. This change has
no effect at all unless the race condition occurs, in which case the
loop will busy-wait until the racing completer callback has finished.
This is a rare condition, so the CPU waste of this spinning is
negligible.
The additional do-while loop relies on usb_anchor_check_wakeup(), which
returns true iff the anchor list is empty, and there is no
__usb_hcd_giveback_urb() in the system that is in the middle of the
unanchor-before-complete phase. The @suspend_wakeups member of
struct usb_anchor is used for this purpose, which was introduced to solve
another problem which the same race condition causes, in commit
6ec4147e7b ("usb-anchor: Delay usb_wait_anchor_empty_timeout wake up
till completion is done").
The surely_empty variable is necessary, because usb_anchor_check_wakeup()
must be called with the lock held to prevent races. However the spinlock
must be released and reacquired if the outer loop spins with an empty
URB list while waiting for the unanchor-before-complete passage to finish:
The completer callback may very well attempt to take the very same lock.
To summarize, using usb_anchor_check_wakeup() means that the patched
functions can return only when the anchor's list is empty, and there is
no invisible URB being processed. Since the inner while loop finishes on
the empty list condition, the new do-while loop will terminate as well,
except for when the said race condition occurs.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200731054650.30644-1-eli.billauer@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c151410d5 ]
When brcmf_proto_msgbuf_attach fail and msgbuf->txflow_wq != NULL,
we should destroy the workqueue.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595237765-66238-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e68cccc8e ]
Eliminate kernel panics when getting invalid responses from controller.
Take controller offline instead of causing kernel panics.
Link: https://lore.kernel.org/r/159622929306.30579.16523318707596752828.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Prasad Munirathnam <Prasad.Munirathnam@microsemi.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed93f9750c ]
Add AE-7 quirk data for setting of microphone. The AE-7 has no front
panel connector, so only rear-mic/line-in have new commands.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Link: https://lore.kernel.org/r/20200825201040.30339-19-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 621a3a8b1c ]
syzbot is reporting that del_timer_sync() is called from
mwifiex_usb_cleanup_tx_aggr() from mwifiex_unregister_dev() without
checking timer_setup() from mwifiex_usb_tx_init() was called [1].
Ganapathi Bhat proposed a possibly cleaner fix, but it seems that
that fix was forgotten [2].
"grep -FrB1 'del_timer' drivers/ | grep -FA1 '.function)'" says that
currently there are 28 locations which call del_timer[_sync]() only if
that timer's function field was initialized (because timer_setup() sets
that timer's function field). Therefore, let's use same approach here.
[1] https://syzkaller.appspot.com/bug?id=26525f643f454dd7be0078423e3cdb0d57744959
[2] https://lkml.kernel.org/r/CA+ASDXMHt2gq9Hy+iP_BYkWXsSreWdp3_bAfMkNcuqJ3K+-jbQ@mail.gmail.com
Reported-by: syzbot <syzbot+dc4127f950da51639216@syzkaller.appspotmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821082720.7716-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9d4709fcc ]
When a usrjquota or grpjquota mount option is used multiple times, we
will leak memory allocated for the file name. Make sure the last setting
is used and all the previous ones are properly freed.
Reported-by: syzbot+c9e294bbe0333a6b7640@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d33fe77bdf ]
When kmalloc() on buf fails, urb should be freed just like
when kmalloc() on dr fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db33235622 ]
ipwireless_send_packet() can only return 0 on success and -ENOMEM on
error, the caller should check non zero for error condition
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Link: https://lore.kernel.org/r/20200821161942.36589-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a49145acfb ]
A fb_ioctl() FBIOPUT_VSCREENINFO call with invalid xres setting
or yres setting in struct fb_var_screeninfo will result in a
KASAN: vmalloc-out-of-bounds failure in bitfill_aligned() as
the margins are being cleared. The margins are cleared in
chunks and if the xres setting or yres setting is a value of
zero upto the chunk size, the failure will occur.
Add a margin check to validate xres and yres settings.
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reported-by: syzbot+e5fd3e65515b48c02a30@syzkaller.appspotmail.com
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dhaval Giani <dhaval.giani@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1594149963-13801-1-git-send-email-george.kennedy@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28b35d17f9 ]
While aborting the I/O, the firmware cleanup task timed out and driver
deleted the I/O from active command list. Some time later the firmware
sent the cleanup task response and driver again deleted the I/O from
active command list causing firmware to send completion for non-existent
I/O and list_del corruption of active command list.
Add fix to check if I/O is present before deleting it from the active
command list to ensure firmware sends valid I/O completion and protect
against list_del corruption.
Link: https://lore.kernel.org/r/20200908095657.26821-4-mrangankar@marvell.com
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0650e2844 ]
Protect active command list for non-I/O commands like login response,
logout response, text response, and recovery cleanup of active list to
avoid list corruption.
Link: https://lore.kernel.org/r/20200908095657.26821-5-mrangankar@marvell.com
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10aff62fab ]
If SUCCESS is not returned, error handling will escalate. Return SUCCESS
similar to other conditions in this function.
Link: https://lore.kernel.org/r/20200907121443.5150-6-jhasan@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bf2f2f331 ]
The Acer One S1003 2-in-1 keyboard dock uses a Synaptics S910xx touchpad
which is connected to an ITE 8910 USB keyboard controller chip.
This keyboard has the same quirk for its rfkill / airplane mode hotkey as
other keyboards with ITE keyboard chips, it only sends a single release
event when pressed and released, it never sends a press event.
This commit adds this keyboards USB id to the hid-ite id-table, fixing
the rfkill key not working on this keyboard. Note that like for the
Acer Aspire Switch 10 (SW5-012) the id-table entry matches on the
HID_GROUP_GENERIC generic group so that hid-ite only binds to the
keyboard interface and the mouse/touchpad interface is left untouched
so that hid-multitouch can bind to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e219688fc5 ]
If a response to virtio_gpu_cmd_get_capset_info takes longer than
five seconds to return, the callback will access freed kernel memory
in vg->capsets.
Signed-off-by: Doug Horn <doughorn@google.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200902210847.2689-2-gurchetansingh@chromium.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86279456a4 ]
Free the skb if usb_submit_urb fails on rx_urb. And free the urb
no matter usb_submit_urb succeeds or not in rtl8xxxu_submit_int_urb.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906040424.22022-1-chiu@endlessm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4443293d7 ]
When wlc_phy_txpwr_srom_read_lcnphy fails in wlc_phy_attach_lcnphy,
the allocated pi->u.pi_lcnphy is leaked, since struct brcms_phy will be
freed in the caller function.
Fix this by calling wlc_phy_detach_lcnphy in the error handler of
wlc_phy_txpwr_srom_read_lcnphy before returning.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200908121743.23108-1-keitasuzuki.park@sslab.ics.keio.ac.jp
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fb5eefd76 ]
Andrii reported that with latest clang, when building selftests, we have
error likes:
error: progs/test_sysctl_loop1.c:23:16: in function sysctl_tcp_mem i32 (%struct.bpf_sysctl*):
Looks like the BPF stack limit of 512 bytes is exceeded.
Please move large on stack variables into BPF per-cpu array map.
The error is triggered by the following LLVM patch:
https://reviews.llvm.org/D87134
For example, the following code is from test_sysctl_loop1.c:
static __always_inline int is_tcp_mem(struct bpf_sysctl *ctx)
{
volatile char tcp_mem_name[] = "net/ipv4/tcp_mem/very_very_very_very_long_pointless_string";
...
}
Without the above LLVM patch, the compiler did optimization to load the string
(59 bytes long) with 7 64bit loads, 1 8bit load and 1 16bit load,
occupying 64 byte stack size.
With the above LLVM patch, the compiler only uses 8bit loads, but subregister is 32bit.
So stack requirements become 4 * 59 = 236 bytes. Together with other stuff on
the stack, total stack size exceeds 512 bytes, hence compiler complains and quits.
To fix the issue, removing "volatile" key word or changing "volatile" to
"const"/"static const" does not work, the string is put in .rodata.str1.1 section,
which libbpf did not process it and errors out with
libbpf: elf: skipping unrecognized data section(6) .rodata.str1.1
libbpf: prog 'sysctl_tcp_mem': bad map relo against '.L__const.is_tcp_mem.tcp_mem_name'
in section '.rodata.str1.1'
Defining the string const as global variable can fix the issue as it puts the string constant
in '.rodata' section which is recognized by libbpf. In the future, when libbpf can process
'.rodata.str*.*' properly, the global definition can be changed back to local definition.
Defining tcp_mem_name as a global, however, triggered a verifier failure.
./test_progs -n 7/21
libbpf: load bpf program failed: Permission denied
libbpf: -- BEGIN DUMP LOG ---
libbpf:
invalid stack off=0 size=1
verification time 6975 usec
stack depth 160+64
processed 889 insns (limit 1000000) max_states_per_insn 4 total_states
14 peak_states 14 mark_read 10
libbpf: -- END LOG --
libbpf: failed to load program 'sysctl_tcp_mem'
libbpf: failed to load object 'test_sysctl_loop2.o'
test_bpf_verif_scale:FAIL:114
#7/21 test_sysctl_loop2.o:FAIL
This actually exposed a bpf program bug. In test_sysctl_loop{1,2}, we have code
like
const char tcp_mem_name[] = "<...long string...>";
...
char name[64];
...
for (i = 0; i < sizeof(tcp_mem_name); ++i)
if (name[i] != tcp_mem_name[i])
return 0;
In the above code, if sizeof(tcp_mem_name) > 64, name[i] access may be
out of bound. The sizeof(tcp_mem_name) is 59 for test_sysctl_loop1.c and
79 for test_sysctl_loop2.c.
Without promotion-to-global change, old compiler generates code where
the overflowed stack access is actually filled with valid value, so hiding
the bpf program bug. With promotion-to-global change, the code is different,
more specifically, the previous loading constants to stack is gone, and
"name" occupies stack[-64:0] and overflow access triggers a verifier error.
To fix the issue, adjust "name" buffer size properly.
Reported-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200909171542.3673449-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0014f9421 ]
Emit a warning when ->done or ->free are called on an already freed
srb. There is a hidden use-after-free bug in the driver which corrupts
the srb memory pool which originates from the cleanup callbacks.
An extensive search didn't bring any lights on the real problem. The
initial fix was to set both pointers to NULL and try to catch invalid
accesses. But instead the memory corruption was gone and the driver
didn't crash. Since not all calling places check for NULL pointer, add
explicitly default handlers. With this we workaround the memory
corruption and add a debug help.
Link: https://lore.kernel.org/r/20200908081516.8561-2-dwagner@suse.de
Reviewed-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Masahiro Fujiwara