Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the omap2plus platforms to be using CONFIG_MULTI_IRQ_HANDLER.
Each machine is modified to provide either omap2_intc_handle_irq(),
omap3_intc_handle_irq() or gic_handle_irq().
This allows for a major cleanup, removing the MULTI_OMAP setup
from the interrupt path.
Tested on both Panda and IGEPv2 (single kernel image)
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Omap cleanups conflicted with omap2_dss work in a nontrivial
way, this is the most logical fixup.
Conflicts:
arch/arm/mach-omap2/board-2430sdp.c
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-apollon.c
arch/arm/mach-omap2/board-h4.c
arch/arm/mach-omap2/board-ldp.c
arch/arm/mach-omap2/board-rx51.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
`keypad_pads' is referred to by `keypad_data' which is
not __initdata, so `keypad_pads' should not be __initdata either.
Signed-off-by: Bjarne Steinsbo <bsteinsbo@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An on-board projector named picodlp is available for OMAP4430 SDP.
Entry for this picodlp as a panel is being added in dss_devices array to
the board file. It needs 4 GPIO pins for interfacing with host
processor and these are defined and two of them are configured in board
file. Two GPIOs power_on and display_select are configured here.
picodlp also needs an i2c client over i2c controller-2 at address 0x1b.
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Mythri P K <mythripk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
4430SDP has two Taal DSI panels, connected to DSI 1 and DSI 2 modules.
The panels use a common PWM backlight, which will be implemented later
when the PWM driver has been improved to support the backlight.
Until the PWM driver has been improved, the following hack added to
arch/arm/mach-omap2/board-4430sdp.c can be used to set the backlight to
max:
static int omap_4430sdp_hack_backlight(void)
{
twl_i2c_write_u8(TWL_MODULE_PWM, 0x7f, LED_PWM2OFF);
twl_i2c_write_u8(TWL_MODULE_PWM, 0x7f, LED_PWM2ON);
twl_i2c_write_u8(TWL6030_MODULE_ID1, 0x30, TWL6030_TOGGLE3);
return 0;
}
late_initcall(omap_4430sdp_hack_backlight);
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
4430SDP board file contains some unused old LCD configurations. They are
not used and can be removed.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use default regn and regm2 dividers in the hdmi driver if the board file
does not define them.
Cc: Mythri P K <mythripk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce them for each omap variant and just make them all call
omap2_init_common_infrastructure for now. Do this for each board-*.c
file except for board-generic and board-omap3beagle as they use
the same machine ID for multiple SoCs.
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to call omap2_init_common_devices from init_early.
It no longer does anything else except reprogram the memory timings
for some boards, so it's better to do it later so we have a chance
to get console messages if something goes wrong.
Move it to happen after omap_serial_init gets called. And while
patching it anyways, rename it to omap_sdrc_init as suggested by
Benoit Cousson <b-cousson@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
The mux settings for keypad are done for omap4430sdp in
board file.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
[tony@atomide.com: improved formatting a bit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add MMC5 support on BLAZE, which has the wl1283 device hardwired to.
The wl1283 is a 4-wire, 1.8V, embedded SDIO WLAN device with an external IRQ line,
and power-controlled by a GPIO-based fixed regulator.
Based on the patch for zoom by Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
[tony@atomide.com: improved formatting a bit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this the HSMMC driver takes GPIO 0 to be the card detect gpio
and requests/configures it. This will give rise to issues when another
driver needs to use GPIO 0. On 4430SDP, the card detection is through
TWL 6030.
Signed-off-by: Silesh C V <silesh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configure, and enable the twl6040 codec on SDP4430.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Add twl4030_vibra platform data, and the needed regulators
for twl6040 vibrator.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reduce the amount of duplicated code by moving the common
configuration for TWL6030 (on OMAP4 platform) to the
twl-common file.
Use the omap4_pmic_get_config function from board files to
properly configure the PMIC with the common fields.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This is no longer needed as we now just set the desired
.timer in MACHINE_START. We can now also remove timer-gp.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
This is needed for the following patches so we can initialize the
rest of the hardware timers later on.
As with the init_irq calls, there's no need to do cpu_is_omap calls
during the timer init as we only care about the major omap generation.
This means that we can initialize the sys_timer with the .timer
entries alone.
Note that for now we just set stubs for the various sys_timer entries
that will get populated in a later patch. The following patches will
also remove the omap_dm_timer_init calls and change the init for the
rest of the hardware timers to happen with an arch_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
to use REGULATOR_SUPPLY arrays.
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Nishant Kamat <nskamat@ti.com>
CC: Steve Sakoman <steve@sakoman.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: peter.barada@logicpd.com
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
eMMC does not handle power off when not in sleep state,
Skip regulator disable during probe when eMMC is
not in known state - state left by bootloader.
Resolves eMMC failure on OMAP4
mmc0: error -110 whilst initialising MMC card
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 contains two separate instances of the padconf registers,
one in the core system config and one in the wakeup system config.
Pass in two tables to apply the correct values to each instance.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The serial*_data should have been marked as __initdata as per
it's usage in the board files. Fix the same to remove the
section mismatch warnings caused by it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Silesh C V <silesh@ti.com>
[tony@atomide.com: updated with additional fixes from Silesh]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
OMAP3: PM: Boot message is not an error, and not helpful, remove it
OMAP3: cpuidle: change the power domains modes determination logic
OMAP3: cpuidle: code rework for improved readability
OMAP3: cpuidle: re-organize the C-states data
OMAP3: clean-up mach specific cpuidle data structures
OMAP3 cpuidle: remove useless SDP specific timings
usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
usb: otg: OMAP4430: Fixing the omap4430_phy_init function
usb: musb: am35x: fix compile error when building am35x
usb: musb: OMAP4430: Power down the PHY during board init
omap: drop board-igep0030.c
omap: igep0020: add support for IGEP3
omap: igep0020: minor refactoring
omap: igep0020: name refactoring for future merge with IGEP3
omap: Remove support for omap2evm
arm: omap2plus: GPIO cleanup
omap: musb: introduce default board config
omap: move detection of NAND CS to common-board-devices
omap: use common initialization for PMIC i2c bus
omap: consolidate touch screen initialization among different boards
...
use gpio_request_<one|array>() instead of multiple gpiolib calls,
remove unneeded variables, etc.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move some of the configurable HDMI PLL parameters to dssdev.clock struct.
Cleanup the function hdmi_compute_pll() by using the parameters defined in the
board file and do some cosmetic modifications.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce omap_pmic_init that registers i2c bus and PMIC device on that
bus and add omap2/3/4 wrappers for common cases.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In Blaze and Panda, 32KHz clock - CLK32KG to WLAN is supplied
from Phoenix TWL6030.
Add CLK32KG platform data to blaze and omap4panda board file.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
Adding board file structure for display which adds the display
structure with HDMI as the default driver when the display init
is called.
HDMI GPIO configurations are also done in this file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.
Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).
Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.
So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modifying the device & driver name from "mmci-omap-hs" to
"omap_hsmmc".
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The usbhs intialization is invoked by all omap3 and omap4
variant board files.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Create the ehci and ohci specific platform data structures.
The port enum values are made common for both ehci and ohci.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
