Here are fixes for omaps to deal with few regressions, and to fix
more boot time errors and warnings:
- The recent ti-sysc interconnect target module driver changes had
incorrect clock bits for both clocks and dts that cause warnings
- For omap3-gta04, gpio changes caused the LCD to break a while back,
and after discussing things the right fix is to set spi-cs-high
- Recent omapdrm changes to use generic panels caused tfp410 to be
disabled as we now must enable the generic support for it in
defconfig
- Recent omapdrm and backlight changes also finally made droid4 LCD
to work, so let's enable it in the defconfig it can be used out
of the box. This is not strictly a fix, but we still also have the
older CONFIG_MFD_TI_LMU options available so this cuts down the
confusion for trying to guess which display and which backlight
is needed
- Recent ti-sysc interconnect target module changes need the gpio
module disabled on some boards, but this now needs to happen at
the module level, not at the gpio driver level
- Recent changes to probe system timers with ti-sysc caused warnings
about mismatch in syconfig registers, so let's configure the option
for RESET_STATUS as available in the TRMs
- Recent changes to probe LCDC with ti-sysc caused warnings about
mismatch in sysconfig registers, so let's configure the missing
idlemodes for both platform data and dts as documented in TRMs
- Since we moved mach-omap2 to probe with device tree, we've been
getting voltage controller warnings. Turns out this code is no
longer needed, so let's just remove omap2_set_init_voltage() to
get rid of the pointless warnings
- Configure am4372 dispc memory bandwidth to avoid underflow errors
-----BEGIN PGP SIGNATURE-----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=SkMF
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.4-rc cycle
Here are fixes for omaps to deal with few regressions, and to fix
more boot time errors and warnings:
- The recent ti-sysc interconnect target module driver changes had
incorrect clock bits for both clocks and dts that cause warnings
- For omap3-gta04, gpio changes caused the LCD to break a while back,
and after discussing things the right fix is to set spi-cs-high
- Recent omapdrm changes to use generic panels caused tfp410 to be
disabled as we now must enable the generic support for it in
defconfig
- Recent omapdrm and backlight changes also finally made droid4 LCD
to work, so let's enable it in the defconfig it can be used out
of the box. This is not strictly a fix, but we still also have the
older CONFIG_MFD_TI_LMU options available so this cuts down the
confusion for trying to guess which display and which backlight
is needed
- Recent ti-sysc interconnect target module changes need the gpio
module disabled on some boards, but this now needs to happen at
the module level, not at the gpio driver level
- Recent changes to probe system timers with ti-sysc caused warnings
about mismatch in syconfig registers, so let's configure the option
for RESET_STATUS as available in the TRMs
- Recent changes to probe LCDC with ti-sysc caused warnings about
mismatch in sysconfig registers, so let's configure the missing
idlemodes for both platform data and dts as documented in TRMs
- Since we moved mach-omap2 to probe with device tree, we've been
getting voltage controller warnings. Turns out this code is no
longer needed, so let's just remove omap2_set_init_voltage() to
get rid of the pointless warnings
- Configure am4372 dispc memory bandwidth to avoid underflow errors
* tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: Set memory bandwidth limit for DISPC
ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
ARM: OMAP2+: Add missing LCDC midlemode for am335x
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
ARM: dts: Fix gpio0 flags for am335x-icev2
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
ARM: dts: Fix wrong clocks for dra7 mcasp
clk: ti: dra7: Fix mcasp8 clock bits
Link: https://lore.kernel.org/r/pull-1570040410-308159@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 6334150e9a ("remoteproc: don't allow modular build")
changes CONFIG_REMOTEPROC to a boolean from a tristate config
option which inhibits all defconfigs marking CONFIG_REMOTEPROC as
a module in compiling the remoteproc and dependent config options.
So fix the configs to have CONFIG_REMOTEPROC built in.
Link: https://lore.kernel.org/r/20190920075946.13282-5-j-keerthy@ti.com
Fixes: 6334150e9a ("remoteproc: don't allow modular build")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Will Deacon <will@kernel.org>
[olof: Fixed up all 4 occurrances in this one commit]
Signed-off-by: Olof Johansson <olof@lixom.net>
A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI
-----BEGIN PGP SIGNATURE-----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=s4qF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: aspeed: ast2500 is ARMv6K
reset: reset-scmi: add missing handle initialisation
firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
Fixes for omap variants
Few fixes for ti-sysc interconnect target module driver for no-idle
quirks that caused nfsroot to fail on some dra7 boards.
And let's fixes to get LCD working again for logicpd board that got
broken a while back with removal of panel-dpi driver. We need to now
use generic CONFIG_DRM_PANEL_SIMPLE instead.
* tag 'fixes-5.4-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
Link: https://lore.kernel.org/r/pull-1568819401-72461@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Droid4 needs USB option serial driver for modem, and lm3532 for the
LCD backlight.
Note that the LCD backlight does not yet get enabled automatically,
but needs to be done manually with:
# echo 50 > /sys/class/leds/lm3532::backlight/brightness
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TFP410 driver was removed but the replacement driver was
never enabled. This patch enableds the DRM_TI_TFP410
Fixes: be3143d8b2 ("drm/omap: Remove TFP410 and DVI connector drivers")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As usual, a bunch of commits, mostly adding drivers and other
options to defconfigs after the code was merged through another
tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=S1hW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"As usual, a bunch of commits, mostly adding drivers and other options
to defconfigs after the code was merged through another tree"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
arm64: defconfig: Enable Qualcomm QUSB2 PHY
arm64: defconfig: Enable the EFI Framebuffer
arm64: defconfig: Enable Qualcomm GENI based I2C controller
ARM: multi_v7_defconfig: Make MAX77802 regulator driver built-in
arm64: defconfig: Enable CPU clock drivers for Qualcomm msm8916
arm64: defconfig: Add DRM_MSM to defconfigs with ARCH_QCOM
ARM: multi_v7_defconfig: Add DRM_MSM to defconfigs with ARCH_QCOM
ARM: qcom_defconfig: Add DRM_MSM to defconfigs with ARCH_QCOM
ARM: configs: aspeed_g5: Enable AST2600
ARM: configs: multi_v7: Add ASPEED G6
arm64: defconfig: Enable SM8150 GCC and pinctrl driver
arm64: defconfig: Enable CONFIG_ACPI_APEI_PCIEAER
arm64: defconfig: Enable the DesignWare watchdog
ARM: multi_v7_defconfig: Enable SPI_STM32_QSPI support
ARM: imx_v6_v7_defconfig: Enable the PSCI CPUidle driver
arm64: defconfig: Enable the PSCI CPUidle driver
arm64: defconfig: Enable Sun4i SPDIF module
ARM: exynos_defconfig: Enable AHCI-platform SATA driver
arm64: defconfig: CONFIG_DRM_ETNAVIV=m
ARM: imx_v6_v7_defconfig: Select the OV5645 camera driver
...
Add modifications necessary to make davinci part of the ARM v5
multiplatform build.
Move the arch-specific configuration out of arch/arm/Kconfig and
into mach-davinci/Kconfig. Remove the sub-menu for DaVinci
implementations (they'll be visible directly under the system type.
Select all necessary options not already selected by ARCH_MULTI_V5.
Update davinci_all_defconfig. Explicitly include the mach-specific
headers in mach-davinci/Makefile.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When the panel-dpi driver was removed, the simple-panels driver
was never enabled, so anyone who used the panel-dpi driver lost
video, and those who used it inconjunction with simple-panels
would have to manually enable CONFIG_DRM_PANEL_SIMPLE.
This patch makes CONFIG_DRM_PANEL_SIMPLE a module in the same
way the deprecated panel-dpi was.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
1. Enable AHCI platform driver on exynos defconfig for Exynos5250-based
Arndale board,
2. Make Max77802 PMIC regulator driver a built-in on multi_v7 defconfig
as it is essential early during boot.
-----BEGIN PGP SIGNATURE-----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=30RN
-----END PGP SIGNATURE-----
Merge tag 'samsung-defconfig-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/defconfig
Samsung defconfig changes for v5.4
1. Enable AHCI platform driver on exynos defconfig for Exynos5250-based
Arndale board,
2. Make Max77802 PMIC regulator driver a built-in on multi_v7 defconfig
as it is essential early during boot.
* tag 'samsung-defconfig-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: multi_v7_defconfig: Make MAX77802 regulator driver built-in
ARM: exynos_defconfig: Enable AHCI-platform SATA driver
Link: https://lore.kernel.org/r/20190904175002.10487-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Add DRM_MSM to ARCH_QCOM defconfigs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0xTo
-----END PGP SIGNATURE-----
Merge tag 'qcom-defconfig-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/defconfig
Qualcomm ARM Based defconfig Updates for v5.4
* Add DRM_MSM to ARCH_QCOM defconfigs
* tag 'qcom-defconfig-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: multi_v7_defconfig: Add DRM_MSM to defconfigs with ARCH_QCOM
ARM: qcom_defconfig: Add DRM_MSM to defconfigs with ARCH_QCOM
5.4, please pull the following:
- Nicolas enables the Raspberry Pi CPUFREQ driver in both
bcm2835_defconfig and multi_v7_defconfig
-----BEGIN PGP SIGNATURE-----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=dVMC
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.4/defconfig' of https://github.com/Broadcom/stblinux into arm/defconfig
This pull request contains Broadcom ARM-based SoCs defconfig updates for
5.4, please pull the following:
- Nicolas enables the Raspberry Pi CPUFREQ driver in both
bcm2835_defconfig and multi_v7_defconfig
* tag 'arm-soc/for-5.4/defconfig' of https://github.com/Broadcom/stblinux:
ARM: defconfig: enable cpufreq driver for RPi
- Enable pinctrl and clock driver support for i.MX8MN SoC.
- Enable SDMA support for i.MX8MQ and i.MX8MM SoC, including
FW_LOADER_USER_HELPER and FW_LOADER_USER_HELPER_FALLBACK to support
SDMA firmware loading via udev.
- Enable module build of i.MX8 DDR PMU driver and ETNAVIV GPU driver.
- Enable module build of OV5645 camera driver in imx_v6_v7_defconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdYqWeAAoJEFBXWFqHsHzO8h8H+wTFJx+q4CF7Z8l+3OCR5rNQ
RSC3gaiYLhQUCEx+HVnvzDvhovdJNyoHiT6qdYqHIO5BYMmacsuWYwuZveaSePCl
WYZ0XkIuvMDZu4KFkl3ufEZx73u/7hbY1s4PevWm7KDeHY28XyWfflX0aW2yM/2Q
1Q/bNjMnsFGJPItBModiwS9lNjxMl7K9XBU47m0K/sJV4LFxbl+2OmfmaQYn4Ook
PAa4XbRH3d/Ff+jXrbwSy+AZZfpsiwDPV6cEwaAOTGr0O6+jKGRzqyAYNTANwjfU
ihUhy/XBjX2GRmGVxqTthDgktoSfX9eVQFU4WfDiHjRYO3y6vpBccC1ixpawUEM=
=iYpD
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/defconfig
i.MX defconfig update for 5.4:
- Enable pinctrl and clock driver support for i.MX8MN SoC.
- Enable SDMA support for i.MX8MQ and i.MX8MM SoC, including
FW_LOADER_USER_HELPER and FW_LOADER_USER_HELPER_FALLBACK to support
SDMA firmware loading via udev.
- Enable module build of i.MX8 DDR PMU driver and ETNAVIV GPU driver.
- Enable module build of OV5645 camera driver in imx_v6_v7_defconfig.
* tag 'imx-defconfig-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: defconfig: CONFIG_DRM_ETNAVIV=m
ARM: imx_v6_v7_defconfig: Select the OV5645 camera driver
arm64: defconfig: Build imx8 ddr pmu as module
arm64: defconfig: Select CONFIG_CLK_IMX8MN by default
arm64: defconfig: Select CONFIG_PINCTRL_IMX8MN by default
arm64: defconfig: Enable SDMA on i.mx8mq/8mm
Link: https://lore.kernel.org/r/20190825153237.28829-7-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Enable the new AST2600 in multi_v7 and the aspeed_g5 configs.
- Regenerate defconfigs to drop old options
- Clean up network options
-----BEGIN PGP SIGNATURE-----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=XO1W
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.4-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/defconfig
ASPEED defconfig updates for 5.4
- Enable the new AST2600 in multi_v7 and the aspeed_g5 configs.
- Regenerate defconfigs to drop old options
- Clean up network options
* tag 'aspeed-5.4-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: configs: aspeed_g5: Enable AST2600
ARM: configs: multi_v7: Add ASPEED G6
ARM: configs: aspeed: Refresh defconfigs
ARM: configs: aspeed: Enable commonly used network functionality
Link: https://lore.kernel.org/r/CACPK8XdyWzghA0QPDzA_MK5FYwhT5afqDJHNdhc8mfD2uk8MfQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Maxim 77802 PMIC is a main PMIC for the following Exynos5 based boards:
Odroid XU, Chromebook Pit and Chromebook Pi. Driver for its voltage
regulator is needed very early during boot to properly instantiate SD/MMC
devices and mount rootfs, so change that driver to be compiled-in.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Now that CONFIG_DRM_MSM is no longer default 'y' add it as a module to all
ARCH_QCOM enabled defconfigs to restore the previous expected build
behavior.
I split this off from the original patch to make this change unique to
the multi_v7_defconfig
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Now that CONFIG_DRM_MSM is no longer default 'y' add it as a module to all
ARCH_QCOM enabled defconfigs to restore the previous expected build
behavior.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
CONFIG_STRICT_KERNEL_RWX is enabled by default with ARMv7.
Turn on HIGHMEM as the EVB has 2GB of RAM, and not all is usable without
hihgmem.
The SoC contains Cortex A7 supporting VFP and has two CPUs.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the ASPEED AST2600 system and associated ASPEED devices so we
get build coverage.
The changes to the UART configuration to ensure the default console
(UART5) works.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
I revisited some older patches here, getting two of the remaining
ARM platforms to build with ARCH_MULTIPLATFORM like most others do.
In case of lpc32xx, I created a new set of patches, which seemed
easier than digging out what I did for an older release many
years ago.
* lpc32xx/multiplatform:
ARM: lpc32xx: allow multiplatform build
ARM: lpc32xx: clean up header files
serial: lpc32xx: allow compile testing
net: lpc-enet: allow compile testing
net: lpc-enet: fix printk format strings
net: lpc-enet: fix badzero.cocci warnings
net: lpc-enet: move phy setup into platform code
net: lpc-enet: factor out iram access
gpio: lpc32xx: allow building on non-lpc32xx targets
serial: lpc32xx_hs: allow compile-testing
watchdog: pnx4008_wdt: allow compile-testing
usb: udc: lpc32xx: allow compile-testing
usb: ohci-nxp: enable compile-testing
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All preparation work is done, so the platform can finally
be moved into ARCH_MULTIPLATFORM. This requires a small
change to the defconfig file to enable the platform.
Link: https://lore.kernel.org/r/20190809144043.476786-14-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The driver uses hardwire MMIO addresses instead of the data
that is passed in device tree. Change it over to only
hardcode the register offset values and allow compile-testing.
Link: https://lore.kernel.org/r/20190809144043.476786-6-arnd@arndb.de
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are three families of IOP machines we support in Linux: iop32x
(which includes EP80219), iop33x and iop13xx (aka IOP34x aka WP8134x).
All products we support in the kernel are based on the first of these,
iop32x, the other families only ever supported the Intel reference
boards but no actual machine anyone could ever buy.
While one could clearly make them all three work in a single kernel
with some work, this takes the easy way out, removing the later two
platforms entirely, under the assumption that there are no remaining
users.
Earlier versions of OpenWRT and Debian both had support for iop32x
but not the others, and they both dropped iop32x as well in their 2015
releases.
Link: https://lore.kernel.org/r/20190809163334.489360-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C parts
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This removes the old Winbond w90x900 platform, also known
as Nuvoton NUC900. Wan Zongshun originally contributed
the port and maintained it since then.
From all I can tell, this platform is no longer being used
with modern kernels, based on various indications:
- The supported chips (nuc910/950/960) are no longer marketed
by the manufacturer
- Newer chips from the same family (nuc97x, nuc980, n329x)
that are still marketed have Linux BSPs but those were never
submitted for upstream inclusion.
- The last patch from the platform maintainer was in 2011.
- All patches to w90x900 platform specific files afterwards
are cleanups that were apparently done without access to
test hardware.
- Both the website and the email address listed in the
MAINTAINERS have become unreachable.
Link: https://lore.kernel.org/r/20190809202749.742267-17-arnd@arndb.de
Cc: "Wanzongshun (Vincent)" <wanzongshun@huawei.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ks8695 is an older SoC originally made by Kendin, which was later acquired
by Micrel, and subsequently by Microchip.
The platform port was originally contributed by Andrew Victor and Ben
Dooks, and later maintained by Greg Ungerer.
When I recently submitted cleanups, but Greg noted that the platform no
longer boots and nobody is using it any more, we decided to remove it.
Link: https://lore.kernel.org/r/20190809202749.742267-2-arnd@arndb.de
Cc: Andrew Victor <linux@maxim.org.za>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Link: https://wikidevi.com/wiki/Micrel
Link: https://lore.kernel.org/linux-arm-kernel/2bc41895-d4f9-896c-0726-0b2862fcbf25@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the PSCI CPUidle driver to replace the functionality
previously provided by the generic ARM CPUidle driver.
Link: https://lore.kernel.org/r/20190814125239.6270-3-lorenzo.pieralisi@arm.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Exynos5250-based Arndale board has one eSATA port, so enable AHCI-platform
driver, which handles it.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
OV5645 camera sensor can be used on several i.MX boards, such as
imx6qdl-wandboard, imx7d-pico, imx6ul-pico, etc.
Select the OV5645 driver by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This enables the driver for STM32 booster regulator found on stm32mp1.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds FMC2 NAND controller support used by STM32MP SOCs.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This enables on both multi_v7_defconfig and bcm2835_defconfig the new
firmware based clock and cpufreq drivers for the Raspberry Pi platform.
In the case of bcm2835_defconfig, as the cpufreq subsystem was disabled,
the conservative governor was selected as default since it better
handles the high frequency transition latency.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
This enables the new or updates driver options for U8500
that got merged into v5.3-rc1:
- CMA, MCDE driver, LIMA driver and the Samsung S6D16D0 driver
enabled by default bringing up the new graphics support.
Include the LOGO so we can see when the graphics are live.
- We use the IIO hwmon bridge for reflecting temperature
in the system.
- Set MUSB to PIO mode as this is the one working most stable
for the time being.
- HWSPINLOCK needs to be set to get the hardware semaphore
driver to compile and link properly.
Link: https://lore.kernel.org/r/20190723081523.13079-2-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This refreshes the outdated U8500 defconfig: some options
moved around, PS/2 mouse is no longer default on, crypto
options moved around etc.
Link: https://lore.kernel.org/r/20190723081523.13079-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This addresses some assumptions made by systemd about having multiple
routing table support in the kernel. systemd-networkd will try and
provision mutliple routing tables + policies and will silently break
neighbor advertisement responses due to policy configurations on a
single table.
It also adds support for SLAAC based router settings and faster
duplicate address detection.
Signed-off-by: William A. Kennington III <wak@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We keep this in a separate branch to avoid cross-branch conflicts, but
most of the material here is fairly boring -- some new drivers turned on
for hardware since they were merged, and some refreshed files due to
time having moved a lot of entries around.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl0yUy8PHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3xMsP+wawhEwoH9kgFkzs4OHVw66BHULejrtYF92Q
piOiLhqHgtLnDjz7oV9e3LNUDfsAutPOscDlYzmEU+v4qhisxF66jnmPzv7ppByJ
c4WJkj38TYo1qyZ3SD/9UY9jHQFZyDj3qeeS6LJdSJVMIf7fL/XsjPFeF3QCrA6w
tabVAgFnx49QD1ucCXedbpBFVpRD+TP2nRSwkVGVDHJ5NKl2z6Pi55hNdWsSpJ/E
Smn02vZolfVrbzvWn+3p+SETSOcwNN0F5DWEbDmlwIrMNhtaV8V91Z1vwB7Zu4pq
khLw8hLpYX9cPnqVHu8aUChu5gAOc7UKU52an9qcguznTp2kvTsaBDPRW/hA8hsr
s6sBL0FmNfVesaGw10zLTYfLbfO1Osq3/8dP3u5kJHfhb4veINy09sjSL76On04c
DuljTQvURH5lXAbt3J4GRnN/x8yZ+LNoT3htElo+59TmR/QOBjQXP0oOPXRVyrDQ
+oHdFuw3LjU9ZxUiTkvqaQag217SFpbuUdMR7RO/dtKlwpAnuofWXy+zDFQ1UcxU
+p7asIo+3Nwiea8MQeB4+XArW20lpTEJUs3GVrqQvCOfmzttS9q842gTPDex8id2
b4VER5MJLV2EQ9JKU1cfMd5IVak9fbnIIgh5tD/UzVVP/s+RwdJQgMeT/RqoCrZc
PTMbqCVX
=Ysfd
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Olof Johansson:
"We keep this in a separate branch to avoid cross-branch conflicts, but
most of the material here is fairly boring -- some new drivers turned
on for hardware since they were merged, and some refreshed files due
to time having moved a lot of entries around"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: configs: multi_v5: Remove duplicate ASPEED options
arm64: defconfig: Enable CONFIG_KEYBOARD_SNVS_PWRKEY as module
ARM: imx_v6_v7_defconfig: Enable CONFIG_ARM_IMX_CPUFREQ_DT
defconfig: arm64: enable i.MX8 SCU octop driver
arm64: defconfig: Add i.MX SCU SoC info driver
arm64: defconfig: Enable CONFIG_QORIQ_THERMAL
ARM: imx_v6_v7_defconfig: Select CONFIG_NVMEM_SNVS_LPGPR
arm64: defconfig: ARM_IMX_CPUFREQ_DT=m
ARM: imx_v6_v7_defconfig: Add TPM PWM support by default
ARM: imx_v6_v7_defconfig: Enable the OV2680 camera driver
ARM: imx_v6_v7_defconfig: Enable CONFIG_THERMAL_STATISTICS
arm64: defconfig: NVMEM_IMX_OCOTP=y for imx8m
ARM: multi_v7_defconfig: enable STMFX pinctrl support
arm64 defconfig: enable LVM support
ARM: configs: multi_v5: Add more ASPEED devices
arm64: defconfig: Add Tegra194 PCIe driver
ARM: configs: aspeed: Add new drivers
ARM: exynos_defconfig: Enable Panfrost and Lima drivers
ARM: multi_v7_defconfig: Enable Panfrost and Lima drivers
arm64 defconfig: enable Mellanox cards
...
We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM Mali
GPU devices added to device trees, since the DRM drivers have now been
merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Polish and fixes for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now at
feature parity with TX1
-----BEGIN PGP SIGNATURE-----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=sHZs
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM Devicetree updates from Olof Johansson:
"We continue to see a lot of new material. I've highlighted some of it
below, but there's been more beyond that as well.
One of the sweeping changes is that many boards have seen their ARM
Mali GPU devices added to device trees, since the DRM drivers have now
been merged.
So, with the caveat that I have surely missed several great
contributions, here's a collection of the material this time around:
New SoCs:
- Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53)
- TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA)
- Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53)
New Boards / platforms:
- Aspeed BMC support for a number of new server platforms
- Kontron SMARC SoM (several i.MX6 versions)
- Novtech's Meerkat96 (i.MX7)
- ST Micro Avenger96 board
- Hardkernel ODROID-N2 (Amlogic G12B)
- Purism Librem5 devkit (i.MX8MQ)
- Google Cheza (Qualcomm SDM845)
- Qualcomm Dragonboard 845c (Qualcomm SDM845)
- Hugsun X99 TV Box (Rockchip RK3399)
- Khadas Edge/Edge-V/Captain (Rockchip RK3399)
Updated / expanded boards and platforms:
- Renesas r7s9210 has a lot of new peripherals added
- Fixes and polish for Rockchip-based Chromebooks
- Amlogic G12A has a lot of peripherals added
- Nvidia Jetson Nano sees various fixes and improvements, and is now
at feature parity with TX1"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (586 commits)
ARM: dts: gemini: Set DIR-685 SPI CS as active low
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Arndale Octa
ARM: dts: exynos: Adjust buck[78] regulators to supported values on Odroid XU3 family
ARM: dts: exynos: Move Mali400 GPU node to "/soc"
ARM: dts: exynos: Fix imprecise abort on Mali GPU probe on Exynos4210
arm64: dts: qcom: qcs404: Add missing space for cooling-cells property
arm64: dts: rockchip: Fix USB3 Type-C on rk3399-sapphire
arm64: dts: rockchip: Update DWC3 modules on RK3399 SoCs
arm64: dts: rockchip: enable rk3328 watchdog clock
ARM: dts: rockchip: add display nodes for rk322x
ARM: dts: rockchip: fix vop iommu-cells on rk322x
arm64: dts: rockchip: Add support for Hugsun X99 TV Box
arm64: dts: rockchip: Define values for the IPA governor for rock960
arm64: dts: rockchip: Fix multiple thermal zones conflict in rk3399.dtsi
arm64: dts: rockchip: add core dtsi file for RK3399Pro SoCs
arm64: dts: rockchip: improve rk3328-roc-cc rgmii performance.
Revert "ARM: dts: rockchip: set PWM delay backlight settings for Minnie"
ARM: dts: rockchip: Configure BT_DEV_WAKE in on rk3288-veyron
arm64: dts: qcom: sdm845-cheza: add initial cheza dt
ARM: dts: msm8974-FP2: Add vibration motor
...
SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus Walleij--
the SoC doesn't have active maintainers with hardware, and in
discussions with the vendor the agreement was that it's OK to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support.
-----BEGIN PGP SIGNATURE-----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=FX6e
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus
Walleij-- the SoC doesn't have active maintainers with hardware,
and in discussions with the vendor the agreement was that it's OK
to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: stm32: use "depends on" instead of "if" after prompt
ARM: sa1100: convert to common clock framework
ARM: exynos: Cleanup cppcheck shifting warning
ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view
ARM: exynos: Only build MCPM support if used
arm: add missing include platform-data/atmel.h
ARM: davinci: Use GPIO lookup table for DA850 LEDs
ARM: OMAP2: drop explicit assembler architecture
ARM: use arch_extension directive instead of arch argument
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
MAINTAINERS: mvebu: Add git entry
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
...
- Add a "cut here" to make it clearer where oops dumps should be cut
from - we already have a marker for the end of the dumps.
- Add logging severity to show_pte()
- Drop unnecessary common-page-size linker flag
- Errata workarounds for Cortex A12 857271, Cortex A17 857272 and
Cortex A7 814220.
- Remove some unused variables that had started to provoke a compiler
warning.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ru/4
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Add a "cut here" to make it clearer where oops dumps should be cut
from - we already have a marker for the end of the dumps.
- Add logging severity to show_pte()
- Drop unnecessary common-page-size linker flag
- Errata workarounds for Cortex A12 857271, Cortex A17 857272 and
Cortex A7 814220.
- Remove some unused variables that had started to provoke a compiler
warning.
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8863/1: stm32: select ARM errata 814220
ARM: 8862/1: errata: 814220-B-Cache maintenance by set/way operations can execute out of order
ARM: 8865/1: mm: remove unused variables
ARM: 8864/1: Add workaround for I-Cache line size mismatch between CPU cores
ARM: 8861/1: errata: Workaround errata A12 857271 / A17 857272
ARM: 8860/1: VDSO: Drop implicit common-page-size linker flag
ARM: arrange show_pte() to issue severity-based messages
ARM: add "8<--- cut here ---" to kernel dumps
1. Trim several configs with savedefconfig.
2. Enable Lima and Panfrost drivers for Mali GPU.
-----BEGIN PGP SIGNATURE-----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=WRDT
-----END PGP SIGNATURE-----
Merge tag 'samsung-defconfig-5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/defconfig
Samsung defconfig changes for v5.3
1. Trim several configs with savedefconfig.
2. Enable Lima and Panfrost drivers for Mali GPU.
* tag 'samsung-defconfig-5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: exynos_defconfig: Enable Panfrost and Lima drivers
ARM: multi_v7_defconfig: Enable Panfrost and Lima drivers
ARM: defconfig: samsung: Cleanup with savedefconfig
ARM: exynos_defconfig: Trim and reorganize with savedefconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
A recent change mistakenly added a second copy of these two options,
which kbuild warns about:
arch/arm/configs/multi_v5_defconfig:257:warning: override: reassigning
to symbol ASPEED_LPC_CTRL
arch/arm/configs/multi_v5_defconfig:258:warning: override: reassigning
to symbol ASPEED_LPC_SNOOP
Fixes: 2d8bf3404b ("ARM: configs: multi_v5: Add more ASPEED devices")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
The SNVS LPGPR hardware is present on several i.MX SoCs.
Select its driver by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Patrice Chotard