Store the upper dword of the register offset in the whitelist as well.
This would allow it to read register where the two halves aren't sitting
right next to each other, and it'll make it easier to make register
access type safe.
While at it change the register offsets to u32 from u64. Our register
space isn't quite that big, yet :)
v2: Use ldw/udw as the suffixes, and add a note about
64bit wide split regs (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446839021-18599-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Most of our register defines follow the convention that if there's a
need for the raw register offset, that one has an underscore sa a
prefix. The define (possibly parametrized) without the underscore is
the one people should normally use, since it will take into account
all the parameters and other potential offsets that are needed.
Fix up the few stragglers that don't follow this convention.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-14-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Handle DC off as a power well where enabling the power well will prevent
the DMC to enter selected DC states (required around modesets and Aux
A). Disabling the power well will allow DC states again. For now the
highest DC state is DC6 for Skylake and DC5 for Broxton but will be
configurable for Skylake in a later patch.
v2: Check both DC5 and DC6 bits in power well enabled function (Ville)
v3:
- Remove unneeded DC_OFF case in skl_set_power_well() (Imre)
- Add PW2 dependency to DC_OFF (Imre)
v4: Put DC_OFF before PW2 in BXT power well array
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[fixed line over 80 and parenthesis alignment checkpatch warns (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1447687201-24759-1-git-send-email-patrik.jakobsson@linux.intel.com
lookup_power_well() expects uniq power well IDs, but atm we have
uninitialized IDs which would clash with those power wells with a 0
ID. This wasn't a problem so far since nothing looked up such a power
well, but an upcoming patch will (Misc IO for SKL), so fix this up on
platforms where this matters.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-2-git-send-email-imre.deak@intel.com
Drop the EDP_PSR_BASE() thing, and just stick the PSR register offset
under dev_priv, like we for DSI and GPIO for example.
TODO: could probably move a bunch of this kind of stuff into the device
info instead...
v2: Drop the spurious whitespace change (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-7-git-send-email-ville.syrjala@linux.intel.com
Currently we determine the location of the AUX registers in a confusing
way. First we assume the PCH registers are used always, but then we
override it for everything but HSW/BDW to use DP+0x10. Very confusing.
Let's just make it straightforward and simply add a few functions to
pick the right AUX_CTL based on the DP port.
To deal with VLV/CHV we'll include the display_mmio_offset into the
AUX register defines.
v2: Reorder patches (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-5-git-send-email-ville.syrjala@linux.intel.com
v2: Keep some MISSING_CASE() stuff (Jani)
s/-1/-PIPE_B/ in the register macro
Fix typo in patch subject
v3: Use PORT_B registers for invalid ports in g4x_aux_ctl_reg() (Jani)
v4: Reorder patches (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v3)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-4-git-send-email-ville.syrjala@linux.intel.com
We check these to determine firmware loading status. Include
them to help to debug causes of firmware loading fails.
v2: Move all CSR specific registers to i915_reg.h (Ville)
v3: Rebase
v4: Rebase (RPM ref)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220487-32691-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
For bxt CSR firmware exposes a count of dc5 entries. Expose
it through debugs
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The CSR firmware expose two counters, handy to check if we are indeed
entering DC5/DC6.
v2: Rebase
v3: Take RPM ref before reading (Imre)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220412-32574-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
SWF18 is set if the display has been initialized by the pre-os. It also
gives what configuration is enabled on which pipe. In skl_sanitize_cdclk,
the DPLL sanity check can pass even if GOP/VBIOS is not loaded as BIOS
enables DPLL for integrated audio codec related programming.
So fisrt check if SWF18 is set and then follow through with other DPLL
and CDCLK verification. If not set then for sure we need to sanitize the
cdclock.
v2: Update the commit message for clarity (Siva)
v3: Correct the mask to check for bits[23:0] instead of only bits[16:0].
Had missed checking for PIPE C altogether. Remaining are reserved (Siva)
v4: Use ILK_SWF macro for SWF register definitions. Taken from Ville's patch
http://lists.freedesktop.org/archives/intel-gfx/2015-November/079480.html
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446726932-14078-1-git-send-email-shobhit.kumar@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Parametrize the SWF registers. This also fixes the register offsets,
which were mostly garbage in the old defines.
Also save/restore only as many SWF registers that each platform has.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PIPE_FRMCOUNT_GM45 and PIPE_FLIPCOUNT_GM45 names have bothered me
for a long time. The work equally well for ELK and onwards, so let's
s/GM45/G4X/.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few register mask defines were missing the '0x' from hex numbers. Or
at least I assume those were meant to be hex numbers. Put the '0x' in
place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always put parens around macro argument evaluations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Keep using the same registers (PCH_*) instead of accidentally
starting to use the other ones (BXT_*)2) (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note that in Bspec you have to dig around in a section called
"Timestamp bases" and Bspec update request is filed.
Signed-off-by: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Add note about state of Bspec.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to support glDispatchComputeIndirect for gen7.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BXT DSI clocks are different than previous platforms. So adding a
new function to program following clocks and dividers:
1. Program variable divider to generate input to Tx clock divider
(Output value must be < 39.5Mhz)
2. Select divide by 2 option to get < 20Mhz for Tx clock
3. Program 8by3 divider to generate Rx clock
v2: Fixed Jani's review comments. Adjusted the Macro definition as
per convention. Simplified the logic for bit definitions for
MIPI PORT A and PORT C in same registers.
v3: Refactored the macros for TX, RX Escape and DPHY clocks as per
Jani's suggestion.
v4: Addressed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains following changes:
1. MIPI device ready changes to support dsi_pre_enable. Changes
are specific to BXT device ready sequence. Added check for
ULPS mode(No effects on VLV).
2. Changes in dsi_enable to pick BXT port control register.
3. Changes in dsi_pre_enable to restrict DPIO programming for VLV
v2: Fixed Jani's review comments. Removed the changes in VLV/CHV
code. Fixed the macros to get proper port offsets.
v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register was added on GEN4, by the name INSTDONE_1 whereas the GEN6
specification calls it INSTDONE_2. Keep the original name with a
platform prefix to make it clearer which INSTDONE register instance this
is. Also add a comment about the SNB alternative name.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a bunch of INSTDONE registers for different platforms and
purposes and it's not immediately clear which instance they are just by
looking at the register name. This one was added on GEN2, where it was
the only INSTDONE register, so mark it as such.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use 3 different names to refer to the same render ring INSTDONE
register. This can be confusing when comparing two parts of the code
accessing the register via different names. Although the GEN4 version's
layout is different, we treat it the same way as the GEN7+ version, in
that we simply read it out during error capture. So remove the
duplicates and leave a comment about the GEN4 difference.
Note that there is also a GEN2 version of this register, but that's on a
different address so not handled in this patch.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Use SKL_DPLLx symbolic names instead of raw numbers
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added checks for available slices, subslices and EUs for Broadwell. This
information is filled in intel_device_info and is available to user with
GET_PARAM.
Added checks for enabled slices, subslices and EU for Broadwell. This
information is based on available counts but takes power gated slices
into account. It can be read in debugfs.
Introduce new register defines that contain information on slices on
Broadwell.
v2:
- Introduce GT_SLICE_INFO register
- Change Broadwell sseu_device_status function to use GT_SLICE_INFO
register instead of RPCS register
- Undo removal of dev_priv variables in Cherryview and Gen9
sseu_device_satus functions
v3:
- Fix style issues
v4:
- Corrected comment
- Reverted reordering of defines
Cc: Jeff Mcgee <jeff.mcgee@intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Łukasz Daniluk <lukasz.daniluk@intel.com>
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As with the cdclk, read out czclk from CCK as well. This gives us the
real current value and avoids having to decode fuses and whatnot.
Also store it in kHz under dev_priv like we do for cdlck since it's not
just an rps related clock, and having it in kHz is more
standard/convenient for some things.
Imre also pointed out that we currently fail to read czclk on VLV, which
means the PFI credit programming isn't working as expected.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the DISPLAY_TRUNK_* and DISPLAY_FREQUENCY_* bits to CCK_... instead
of DISPLAY_... to make it clear they apply to all CCK clock control registers.
Suggested by Ville.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Hide the 945 vs. rest of gen2/3 difference in the macro
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec update tells that we have to enable oscaledcompmethod instead of
ouniqetrangenmethod for enabling scale value during swing programming.
v2: Adding back 'don't care' values to bxt_ddi_translations_dp and add
error message if ouniquetrangemethod was set (Imre)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>(v1)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIXME: Should there be a WARN(i != 9) or something, or what does the
entry 9 comment mean?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Finally managed to dig up enough hints as to where the stolen
reserved stuff lives on ctg/elk. So add the code to decode it.
This was a combination of old chipset specs, diggin up an old
elk grits release with an ctg/elk AubLoad etc.
This was only tested on an elk as I don't have a ctg here
unfortunately.
This leaves ilk as the only platform that doesn't have a way
to detect this stuff. Looking at the register contents on my
ilk, it might be that the elk way works there too, but I
can't be sure since I can't affect the amount of reserved
memory on that machine, and if I am to trust the register
contents, by default it would reserve 0 bytes.
v2: s/WARN_ON_ONCE/WARN_ON/ since it's in one time init code
anyway (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch modifies dsi_prepare() function to support the same
modeset prepare sequence for BXT also. Main changes are:
1. BXT port control register is different than VLV.
2. BXT modeset sequence needs vdisplay and hdisplay programmed
for transcoder.
3. BXT can select PIPE for MIPI transcoders.
4. BXT needs to program register MIPI_INIT_COUNT for both the ports,
even if only one is being used.
v2: Fixed Jani's review comments. Rectified the DSI Macros to get
proper register offsets using _MIPI_PORT instead of _TRANSCODER
v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds new functions for BXT clock and PLL programming.
They are:
1. configure_dsi_pll for BXT.
This function does the basic math and generates the divider ratio
based on requested pixclock, and program clock registers.
2. enable_dsi_pll function.
This function programs the calculated clock values on the PLL.
3. intel_enable_dsi_pll
Wrapper function to use same code for multiple platforms. It checks the
platform and calls appropriate core pll enable function.
v2: Fixed Jani's review comments. Macros are adjusted as per convention.
v3: Removed a redundant change wrt code comment.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normally we determine the backlight PWM modulation frequency (which we
also use as backlight max value) from the backlight registers at module
load time, expecting the registers have been initialized by the BIOS. If
this is not the case, we fail.
The VBT contains the backlight modulation frequency in Hz. Add platform
specific functions to convert the frequency in Hz to backlight PWM
modulation frequency, and use them to initialize the backlight when the
registers are not initialized by the BIOS.
v2: Fix SPT and VLV. Thanks to Clint for the VLV code.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rewrite the BXT hpd setup to match the way we do it on other platforms:
- Throw out BXT_HOTPLUG_CTL since it's the same as PCH_PORT_HOTPLUG
- Enable the HPD bits in the DE port IER in gen8_de_irq_postinstall()
- Update DE port IMR using bdw_update_port_irq()
Also throw out port D from bxt_port_hotplug_long_detect() since BXT only
goes up to C.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL the port A HPD has moved to the PCH. Hook it up.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PORTA HPD defines are not BXT specific. They also exist on SPT,
and partially already on LPT:LP.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Indent the PORTx_HOTPLUG_... defines appropriately, and fix some space
vs. tab issues.
v2: Document pre-HSW/LPT bits, and order another tab (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
At various points when changing the DPIO lane/phy power states,
construct an expected value of the DISPLAY_PHY_STATUS register
and compare it with the real thing.
To construct the expected value we look at our shadow PHY_CONTROL
register value (which should match what we've just written to the
hardware), and we also need to look at the actual state of the cmn
power wells as a disabled power well causes the relevant LDO status
to be reported as 'on' in DISPLAY_PHY_STATUS.
When initially powering up the PHY it performs various internal
calibrations for which it fully powers up. That means that if we check
for the expetected power state immediately upon releasing cmnreset we
would get the occasional false positive. But we can of course
poll until the expected value appears. It shouldn't be too long so
this shouldn't make modesets substantially longer.
One extra complication is introduced when we cross the streams, ie.
drive port B with pipe B. In this case we trick CL2 (where the DPLL lives)
into life by temporaily powering up the lanes in the second channel,
and once the pipe is up and runnign we release the lane power override.
At that point the power state of CL2 has somehow gotten entangled with
the power state of the first channel. That means that constructing the
expected DISPLAY_PHY_STATUS value is a bit tricky since based on the
lane power states in the second channel, CL2 should also be powered
down. But we can use the DPLL enable bit to determine when CL2 should
be alive even if the lanes are powered down. However the power state
of CL2 isn't actually tied in with the DPLL state, but to the state
of the lanes in first channel, so we have to avoid checking the
expected state between shutting down the DPLL and powering down
the lanes in the first channel. So no calling assert_chv_phy_status()
before the DISPLAY_PHY_CONTROL write in chv_phy_powergate_lanes(),
but after the write is a safe time to check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add some checks that the state of the DPIO lanes is more or less what we
expect based on the overrides.
The hardware only provides two bits per channel indicating whether all
or some of the lanes are powered down, so we can't do an exact check.
Additionally, CL2 powering down before we can check it adds another
twist. To work around this we simply check for the 0 value of the
CL2 register (which is what we get when it's powered down) and
adjust our expectations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can choose to leave the display PHY CL2 powerdown up to some hardware
signals, or we can force it. The BXT code forces the nonexistent CL2 in
the x1 PHY to power down. Follow suit on CHV. Maybe it can still save
some extra power by disabling some extra logic in CL1, or something.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has supports some form of automagic clock gating for the
DPIO SUS clock. We can simply enable the magic bits and the
hardware should take care of the rest.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Powergate the PHY lanes when they're not needed. For HDMI all four lanes
are needed always, but for DP we can enable only the needed lanes. To
power down the unused lanes we use some power down override bits in the
DISPLAY_PHY_CONTROL register. Without the overrides it appears that the
hardware always powers on all the lanes. When the port is disabled the
power down override is not needed and the lanes will shut off on their
own. That also means the override is critical to actually be able to
access the DPIO registers before the port is actually enabled.
Additionally the common lanes will power down when not needed. CL1
remains on as long as anything else is on, CL2 will shut down when
all the lanes in the same channel will shut down. There is one exception
for CL2 that will be dealt in a separate patch for clarity.
With potentially some lanes powered down, the DP code now has to check
the number of active lanes before accessing PCS/TX registers. All
registers in powered down blocks will reads as 0xffffffff, and soe we
would drown in warnings from vlv_dpio_read() if we allowed the code
to access all those registers.
Another important detail in the DP code is the "TX latency optimal"
setting. Normally the second TX lane acts as some kind of reset master,
with the other lanes as slaves. But when only a single lane is enabled,
that single lane obviously has to be the master.
A bit of extra care is needed to reconstruct the initial state of the
DISPLAY_PHY_CONTROL register since it can't be read safely. So instead
read the actual lane status from the DPLL/PHY_STATUS registers and
use that to determine which lanes ought to be powergated initially.
We also need to switch the PHY power modes to "deep PSR" to avoid
a hard system hang when powering down the single channel PHY.
Also sprinkle a few debug prints around so that we can monitor the
DISPLAY_PHY_STATUS changes without having to read it and risk
corrupting it.
v2: Add locking to chv_powergate_phy_lanes()
v3: Actually enable dynamic powerdown in the PHY and deal with the
fallout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: fix one error found by checkpath.pl
v3: Add one ignored break for switch-case. DDI-E hotplug
function doesn't work after updating drm-intel tree,
I checked the code and found this missing which isn't
the root cause for broke DDI-E hp. The broken
DDI-E hp function is fixed by "Adding DDI_E power
well domain".
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Timo Aaltonen <timo.aaltonen@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
MI_STORE_REGISTER_MEM, MI_LOAD_REGISTER_MEM instructions are not really
variable length instructions unlike MI_LOAD_REGISTER_IMM where it expects
(reg, addr) pairs so use fixed length for these instructions.
v2: rebase
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Appease checkpatch as Mika spotted in i915_reg.h - it seems
terminally unhappy about i915_cmd_parser.c so that would be a separate
patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turn on interrupt steering to route necessary interrupts to GuC.
v6:
Rebased
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fetches the required firmware image from the filesystem,
then loads it into the GuC's memory via a dedicated DMA engine.
This patch is derived from GuC loading work originally done by
Vinit Azad and Ben Widawsky.
v2:
Various improvements per review comments by Chris Wilson
v3:
Removed 'wait' parameter to intel_guc_ucode_load() as firmware
prefetch is no longer supported in the common firmware loader,
per Daniel Vetter's request.
Firmware checker callback fn now returns errno rather than bool.
v4:
Squash uC-independent code into GuC-specifc loader [Daniel Vetter]
Don't keep the driver working (by falling back to execlist mode)
if GuC firmware loading fails [Daniel Vetter]
v5:
Clarify WOPCM-related #defines [Tom O'Rourke]
Delete obsolete code no longer required with current h/w & f/w
[Tom O'Rourke]
Move the call to intel_guc_ucode_init() later, so that it can
allocate GEM objects, and have it fetch the firmware; then
intel_guc_ucode_load() doesn't need to fetch it later.
[Daniel Vetter].
v6:
Update comment describing intel_guc_ucode_load() [Tom O'Rourke]
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we clobber intel_dp->lane_count in compute config, which means
after a rejected modeset we may no longer be able to retrain the current
link. Move lane_count into pipe_config to avoid that.
v2: Add missing ':' to the pipe config debug dump
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In 64b (48bit canonical) PPGTT addressing, the PDP0 register contains
the base address to PML4, while the other PDP registers are ignored.
In LRC, the addressing mode must be specified in every context
descriptor, and the base address to PML4 is stored in the reg state.
v2: PML4 update in legacy context switch is left for historic reasons,
the preferred mode of operation is with lrc context based submission.
v3: s/gen8_map_page_directory/gen8_setup_page_directory and
s/gen8_map_page_directory_pointer/gen8_setup_page_directory_pointer.
Also, clflush will be needed for bxt. (Akash)
v4: Squashed lrc-specific code and use a macro to set PML4 register.
v5: Rebase after Mika's ppgtt cleanup / scratch merge patch series.
PDP update in bb_start is only for legacy 32b mode.
v6: Rebase after final merged version of Mika's ppgtt/scratch
patches.
v7: There is no need to update the pml4 register value in
execlists_update_context. (Akash)
v8: Move pd and pdp setup functions to a previous patch, they do not
belong here. (Akash)
v9: Check USES_FULL_48BIT_PPGTT instead of GEN8_CTX_ADDRESSING_MODE in
gen8_emit_bb_start to check if emit pdps is needed. (Akash)
Cc: Akash Goel <akash.goel@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I started digging this when I noticed that the BDW code was just
reserving 1mb by coincidence since it was reading reserved fields.
Then I noticed we didn't have any values set for SNB and earlier, and
that the HSW sizes were wrong. After that, I noticed that the reserved
area has a specific start, and may not exactly end where the stolen
memory ends. I also noticed the base pointer can be zero. So I decided
to just write a single patch fixing everything instead of 20 patches
that would be much harder to review.
This patch may solve random stolen memory corruption/problems on
almost all platforms. Notice that since this is always dealing with
the top of the stolen memory, the problems are not so easy to
reproduce - especially since FBC is still disabled by default.
One of the major differences of this patch is that we now look at both
the size and base address. By only looking at the size we were
assuming that the reserved area was always at the very top of
stolen, which is not always true.
After we merge the patch series that allows user space to allocate
stolen memory we'll be able to write IGT tests that maybe catch the
bugs fixed by this patch.
v2:
- s/BIOS reserved/stolen reserved/g (Chris)
- Don't DRM_ERROR if we can't do anything about it (Chris)
- Improve debug messages (Chris).
- Use the gen7 version instead of gen6 on HSW. Tom found some
documentation problems, so I think with gen7 we're on the safer
side (Tom).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a requirement for enabling display port HPD support on the port
A HPD pin. This support is to be added by follow-up patches.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge fixes since it's getting out of hand again with the massive
split due to atomic between -next and 4.2-rc. All the bugfixes in
4.2-rc are addressed already (by converting more towards atomic
instead of minimal duct-tape) so just always pick the version in next
for the conflicts in modeset code.
All the other conflicts are just adjacent lines changed.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem_gtt.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
drivers/gpu/drm/i915/intel_ringbuffer.h
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This change adds the programming of the MOCS registers to the gen 9+
platforms. The set of MOCS configuration entries introduced by this
patch is intended to be minimal but sufficient to cover the needs of
current userspace - i.e. a good set of defaults. It is expected to be
extended in the future to provide further default values or to allow
userspace to redefine its private MOCS tables based on its demand for
additional caching configurations. In this setup, userspace should
only utilize the first N entries, higher entries are reserved for
future use.
It creates a fixed register set that is programmed across the different
engines so that all engines have the same table. This is done as the
main RCS context only holds the registers for itself and the shared
L3 values. By trying to keep the registers consistent across the
different engines it should make the programming for the registers
consistent.
v2:
-'static const' for private data structures and style changes.(Matt Turner)
v3:
- Make the tables "slightly" more readable. (Damien Lespiau)
- Updated tables fix performance regression.
v4:
- Code formatting. (Chris Wilson)
- re-privatised mocs code. (Daniel Vetter)
v5:
- Changed the name of a function. (Chris Wilson)
v6:
- re-based
- Added Mesa table entry (skylake & broxton) (Francisco Jerez)
- Tidied up the readability defines (Francisco Jerez)
- NUMBER of entries defines wrong. (Jim Bish)
- Added comments to clear up the meaning of the tables (Jim Bish)
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
v7 (Francisco Jerez):
- Don't write L3-specific MOCS_ESC/SCC values into the e/LLC control
tables. Prefix L3-specific defines consistently with L3_ and
e/LLC-specific defines with LE_ to avoid this kind of confusion in
the future.
- Change L3CC WT define back to RESERVED (matches my hardware
documentation and the original patch, probably a misunderstanding
of my own previous comment).
- Drop Android tables, define new minimal tables more suitable for the
open source stack.
- Add comment that the MOCS tables are part of the kernel ABI.
- Move intel_logical_ring_begin() and _advance() calls one level down
(Chris Wilson).
- Minor formatting and style fixes.
v8 (Francisco Jerez):
- Add table size sanity check to emit_mocs_control/l3cc_table() (Chris
Wilson).
- Add comment about undefined entries being implicitly set to uncached
for forwards compatibility.
v9 (Francisco Jerez):
- Minor style fixes.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop the spurious 'A' from the VLV/CHV ref clock enable define,
and add the "REF" to the VLV ref clock selection bit. Also
s/CLOCK/CLK/ for extra consistency.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In this WA we need to set GEN8_L3SQCREG4[21:21] and reset it after PIPE_CONTROL
instruction but there is a slight complication as this is applied in WA batch
where the values are only initialized once.
Dave identified an issue with the current implementation where the register value
is read once at the beginning and it is reused; this patch corrects this by saving
the register value to memory, update register with the bit of our interest and
restore it back with original value.
This implementation uses MI_LOAD_REGISTER_MEM which is currently only used
by command parser and was using a default length of 0. This is now updated
with correct length and moved to appropriate place.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also clarify comments on context size that the extra state for
Resource Streamer is included.
v2: Don't remove the extended save/restore enabled for older
platforms. (Ville)
Use new MI_SET_CONTEXT defines for HSW RS save/restore state
instead of extended save/restore. (Daniel)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adds support for enabling the resource streamer on the legacy
ringbuffer for HSW and GEN8.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains changes based on 2 updates to the spec:
Port PLL VCO restriction raised up to 6700.
Port PLL now needs DCO amp override enable for all VCO frequencies.
v2: Sonika's review comment addressed
- dcoampovr_en_h variable not required
Based on a discussion with Siva, the following changes have been made.
- replace dco_amp var with #define BXT_DCO_AMPLITUDE
- set pll10 in a single assignment
v3:
Move DCO amplitude default value to i915_reg.h. Suggested by Siva.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com> [v2]
[danvet: Spell out BUN since not everyone knows what this means.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull intel drm fixes from Jani Nikula:
"Almost all of it is regression fixes all around, with cc: stable, and
then there's Ander's fix for one of the warnings you reported. We're
still working on the rest"
[ Dave is on vacation, and Jani is heading out on vacation too ]
* tag 'drm-intel-next-fixes-2015-07-02' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Clear pipe's pll hw state in hsw_dp_set_ddi_pll_sel()
drm/i915: fix backlight after resume on 855gm
agp/intel: Fix typo in needs_ilk_vtd_wa()
drm/i915/ppgtt: Break loop in gen8_ppgtt_clear_range failure path
drm/i915: Fix IPS related flicker
Add support for reading out the HW state for DDI ports. Since the actual
programming is very similar to the CHV/VLV DPIO PLL programming we can
reuse much of the logic from there.
This fixes the state checker failures I saw on my BXT with HDMI output.
v2:
- rebased on v2 of patch 4/5
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Although we have a fixed setting for the PLL9 and EBB4 registers, it
still makes sense to check them together with the rest of PLL registers.
While at it also remove a redundant comment about 10 bit clock enabling.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some 855gm models (at least ThinkPad X40) regressed because of
commit b0cd324fae
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Nov 12 16:25:43 2014 +0200
drm/i915: don't save/restore backlight hist ctl registers
which tried to make our driver more robust by not blindly saving and
restoring registers, but it failed to take into account
commit 0eb96d6ed3
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Oct 14 12:33:41 2009 -0700
drm/i915: save/restore BLC histogram control reg across suspend/resume
Fix the regression by enabling hist ctl on gen2.
v2: Improved the comment.
v3: Improved the comment, again.
Reported-and-tested-by: Philipp Gesang <phg@phi-gamma.net>
References: http://mid.gmane.org/20150623222648.GD12335@acheron
Fixes: b0cd324fae ("drm/i915: don't save/restore backlight hist ctl registers")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Consider which planes are active and compute the FIFO split based on the
relative data rates. Since we only consider the pipe src width rather
than the plane width when computing watermarks it seems best to do the
same when computing the FIFO split as well. This means the only thing we
actually have to consider for the FIFO splut is the bpp, and we can
ignore the rest.
I've just stuffed the logic into the watermark code for now. Eventually
it'll need to move into the atomic update for the crtc.
There's also one extra complication I've not yet considered; Some of the
DSPARB registers contain bits related to multiple pipes. The registers
are double buffered but apparently they update on the vblank of any
active pipe. So doing the FIFO reconfiguration properly when multiple
pipes are active is not going to be fun. But let's ignore that mess for
now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.2.
I've one other new driver from freescale on my radar, it's been posted
and reviewed, I'd just like to get someone to give it a last look, so
maybe I'll send it or maybe I'll leave it.
There is no major nouveau changes in here, Ben was working on
something big, and we agreed it was a bit late, there wasn't anything
else he considered urgent to merge.
There might be another msm pull for some bits that are waiting on
arm-soc, I'll see how we time it.
This touches some "of" stuff, acks are in place except for the fixes
to the build in various configs,t hat I just applied.
Summary:
New drivers:
- virtio-gpu:
KMS only pieces of driver for virtio-gpu in qemu.
This is just the first part of this driver, enough to run
unaccelerated userspace on. As qemu merges more we'll start
adding the 3D features for the virgl 3d work.
- amdgpu:
a new driver from AMD to driver their newer GPUs. (VI+)
It contains a new cleaner userspace API, and is a clean
break from radeon moving forward, that AMD are going to
concentrate on. It also contains a set of register headers
auto generated from AMD internal database.
core:
- atomic modesetting API completed, enabled by default now.
- Add support for mode_id blob to atomic ioctl to complete interface.
- bunch of Displayport MST fixes
- lots of misc fixes.
panel:
- new simple panels
- fix some long-standing build issues with bridge drivers
radeon:
- VCE1 support
- add a GPU reset counter for userspace
- lots of fixes.
amdkfd:
- H/W debugger support module
- static user-mode queues
- support killing all the waves when a process terminates
- use standard DECLARE_BITMAP
i915:
- Add Broxton support
- S3, rotation support for Skylake
- RPS booting tuning
- CPT modeset sequence fixes
- ns2501 dither support
- enable cmd parser on haswell
- cdclk handling fixes
- gen8 dynamic pte allocation
- lots of atomic conversion work
exynos:
- Add atomic modesetting support
- Add iommu support
- Consolidate drm driver initialization
- and MIC, DECON and MIPI-DSI support for exynos5433
omapdrm:
- atomic modesetting support (fixes lots of things in rewrite)
tegra:
- DP aux transaction fixes
- iommu support fix
msm:
- adreno a306 support
- various dsi bits
- various 64-bit fixes
- NV12MT support
rcar-du:
- atomic and misc fixes
sti:
- fix HDMI timing complaince
tilcdc:
- use drm component API to access tda998x driver
- fix module unloading
qxl:
- stability fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits)
drm/nouveau: Pause between setting gpu to D3hot and cutting the power
drm/dp/mst: close deadlock in connector destruction.
drm: Always enable atomic API
drm/vgem: Set unique to "vgem"
of: fix a build error to of_graph_get_endpoint_by_regs function
drm/dp/mst: take lock around looking up the branch device on hpd irq
drm/dp/mst: make sure mst_primary mstb is valid in work function
of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/atomic: Don't set crtc_state->enable manually
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
...
Broxton is using a different register and different bit ordering
for rps status capabilities.
Also GT perf freqency register is different for Broxton so update
that.
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Indirect context w/a batch buffer,
WaClearSlmSpaceAtContextSwitch
This WA performs writes to scratch page so it must be valid, this check
is performed before initializing the batch with this WA.
v2: s/PIPE_CONTROL_FLUSH_RO_CACHES/PIPE_CONTROL_FLUSH_L3 (Ville)
v3: GTT bit in scratch address should be mbz (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Indirect context w/a batch buffer,
+WaFlushCoherentL3CacheLinesAtContextSwitch:bdw
v2: Add LRI commands to set/reset bit that invalidates coherent lines,
update WA to include programming restrictions and exclude CHV as
it is not required (Ville)
v3: Avoid unnecessary read when it can be done by reading register once (Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order for gen8+ hardware to guarantee that no context switch
takes place during engine reset and that current context is properly
saved, the driver needs to notify and query hw before commencing
with reset.
There are gpu hangs where the engine gets so stuck that it never will
report to be ready for reset. We could proceed with reset anyway, but
with some hangs with skl, the forced gpu reset will result in a system
hang. By inspecting the unreadiness for reset seems to correlate with
the probable system hang.
We will only proceed with reset if all engines report that they
are ready for reset. If root cause for system hang is found and
can be worked around with another means, we can reconsider if
we can reinstate full reset for unreadiness case.
v2: -EIO, Recovery, gen8 (Chris, Tomas, Daniel)
v3: updated commit msg
v4: timeout_ms, simpler error path (Chris)
References: https://bugs.freedesktop.org/show_bug.cgi?id=89959
References: https://bugs.freedesktop.org/show_bug.cgi?id=90854
Testcase: igt/gem_concurrent_blit/prw-blt-overwrite-source-read-rcs-forked
Testcase: igt/gem_concurrent_blit/gtt-blt-overwrite-source-read-rcs-forked
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tomas Elf <tomas.elf@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Changes for BXT - added a IS_BROXTON check to use the macro related to PPS
registers for BXT.
BXT does not have PP_DIV register. Making changes to handle this.
Second set of PPS registers have been defined but will be used when VBT
provides a selection between the 2 sets of registers.
v2:
[Jani] Added 2nd set of PPS registers and the macro
Jani's review comments
- remove reference in i915_suspend.c
- Use BXT PP macro
Squashing all PPS related patches into one.
v3: Jani's review comments addressed
- Use pp_ctl instead of pp
- ironlake_get_pp_control() is not required for BXT
- correct the use of && in the print statement
- drop the shift in the print statement
v4: Jani's comments
- modify ironlake_get_pp_control() - dont set unlock key for bxt
v5: Sonika's comments addressed
- check alignment
- move pp_ctrl_reg write (after ironlake_get_pp_control())
to !IS_BROXTON case.
- check before subtracting 1 for t11_t12
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already had a few bugs in the past where FBC was compressing
nothing when it was enabled, which makes the feature quite useless.
Add this information to debugfs so the test suites can check for
regressions in this piece of the code.
Our igt/tests/kms_frontbuffer_tracking already has support for this
message.
v2: - Remove pointless VLV check (Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GCP infoframes are required to inform the HDMI sink about the color
depth.
Send the GCP infoframe whenever the sink supports any deep color modes
since such sinks must anyway be capable of receiving them. For sinks
that don't support deep color let's skip the GCP in case it might
confuse the sink, although HDMI 1.4 spec does say all sinks must be
capable of reciving them. In theory we could skip the GCP infoframe
for deep color sinks in 8bpc mode as well since sinks must fall back to
8bpc whenever GCP isn't received for some time.
BSpec says we should disable GCP after disabling the port, so do that as
well.
v2: s/intel_set_gcp_infoframe/intel_hdmi_set_gcp_infoframe/
Rebased due to crtc->config changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict with lack of chv phy patches and fixup typo
Chandra spotted.]
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CPT/PPT require a specific procedure for enabling 12bpc HDMI. Implement
it, and to keep things neat pull the code into a function.
v2: Rebased due to crtc->config changes
s/HDMI_GC/HDMIUNIT_GC/ to match spec better
Factor out intel_enable_hdmi_audio()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-By: Chandra Konduru <Chandra.konduru@intel.com>
Testecase: igt/kms_render/*
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for changing cdclk frequency during runtime on BDW.
Also with IPS enabled the actual pixel rate mustn't exceed 95% of cdclk,
so take that into account when computing the max pixel rate.
v2: Grab rps.hw_lock around sandybridge_pcode_write()
v3: Rebase due to power well vs. .global_resources() reordering
v4: Rebased to the latest
v5: Rebased to the latest
v6: Patch order shuffle so that Broadwell CD clock change is
applied before the patch for Haswell CD clock change
v7: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
