Add const to functions that return strings that aren't going to be
modified. This addresses some reported compile complaints.
Change-ID: Ic56b1e814ab4d23a50480e7fdec652445f776ee8
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code in i40e and i40evf is using an "IN_NETPOLL" flag that has never
added any value due to the fact that the Rx clean-up is handled in NAPI.
As such the flag was set, the queue was scheduled via NAPI, and then polled
from the netpoll controller and if any Rx packets were processed the were
processed in the wrong context.
In addition the flag itself just added an unneeded conditional to the
hot-path so it can safely be dropped and save us a few instructions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The polling routine for i40e was rounding up the budget for Rx cleanup to
1. This is incorrect as the netpoll poll call is expecting no Rx to be
processed as the budget passed was 0.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shorten up the delays in the init task, allowing the VF driver to
initialize faster. This aids performance in load/unload tests and
mitigates DMAR errors in VF enable/disable tests with absurdly short
delays. In the real world, the VF driver will come up more quickly.
The original values were set conservatively based on what we expected
from the firmware in terms of performance. Now that the driver is in use
and we know how well firmware responds to our requests, we can shorten
these delays.
Change-ID: Ibead77d34b19e8170e667c3f58bc14748bbc5bc9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a variable declaration inside an if block hiding an existing
declaration at the start of the function.
Also remove a forward function declaration that is no longer needed due
to code re-organization.
Change-ID: I12954668b722718074949c93d74cd20eaacd93e4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 has a way to work around the descriptor WB issue,
this offload helps turn that feature on.
Change-ID: I7ffa67622426bfca5a651417b63e3afcfeb60412
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These are not implementations of default architecture code but helpers
for drivers. Move them to the place they belong to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove unused members in the PHY structure and add a new member to store
all the capabilities the PHY has as reported by the FW. This information
will help us determine what speeds the device is capable of when link is
down.
Also add an enum to decode the PHY types the NVM is capable of.
Use the phy_types variable to determine what phy types are possible
when link is down instead of device id as it will be more accurate.
When on a backplane device, we do not support changing any settings,
however we should display all the phy_types we are capable of so if we
see a backplane dev ID set supported and advertised purely based on
the phy_types variable.
Change-ID: Ia75d560f1fcd30c54cbfb7458690c5867559a930
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a module_types variable to the link_info struct to save the module
information from get_phy_capabilities. This information can be used to
determine which speeds the module supports.
Also add a new function update_link_info which updates the module_types
parameter and then calls get_link_info. This function should be called
in place of get_link_info so that the module_types variable stays
up-to-date with the rest of the link information.
The EAS table does not reflect the values that are actually returned,
so instead, basing these values on the Ethernet compliance codes
specified in table 33 of SFF-8436 as these have been accurate.
Use the new variable in ethtool to differentiate between a 10G/1G dual
speed fiber module and a 10G only module.
Change-ID: Ib7585cce321319c10ce15180054c41a6cbd41389
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to desires to write userland drivers, and other requests, without
needing the rest of the include files, the device ids are pulled out
into a standalone file.
Change-ID: Ic0b047dbf9d4b0891892309c1f2079f56d9b60e8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a member to the nvm_info struct for oem_ver info to be
output either by OID or ethtool.
Change-ID: I1e5d513ae67622e2af17042924fdb4b5d6d85366
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was not correctly handling calls to its ndo_set_mac_address
method. It did not properly check to see if the override would be
allowed by the PF driver, and never removed the old address from its
filter list.
Add a new flag to the adapter struct which is set if the MAC address is
assigned by the PF. Check this flag and don't allow the MAC address to
be changed if it is set. Search for and properly remove the filter
for the old MAC address when the new one is set.
Change-ID: I817bf620c869c5a80e6a7eab65c9cbad1dc89799
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the new Port link status bit and rename the link status to function
link status.
Change-ID: I71289327ae62638ce967b6ad40114caf998b6dab
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF really doesn't care about the QOS handle but it will in the
future. Since the VF only uses TC0, send it that handle. On the VF
side, save the handle and use it to populate the QOS params when we call
into the client interface.
Change-ID: I76f41b070baeaa09b19383e9168bc677837e0761
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the capabilities passed to us by the PF driver to control VF driver
behavior. In the process, clean up the VLAN add/remove code so it's not
a horrible morass of ifdefs.
Change-ID: I1050eaf12b658a26fea6813047c9964163c70a73
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add missings spaces after declarations, remove another __func__ use,
remove uncessary braces, remove unneeded breaks, and useless returns,
and generally fix up some code.
Change-ID: Ie715d6b64976c50e1c21531685fe0a2bd38c4244
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using VFGEN_RSTAT to detect a VF reset is an endeavor that is fraught
with peril. It's entirely too easy to miss a reset because none of the
bits are sticky. By the time the VF driver reads the register, the reset
may have been processed and cleaned up by the PF driver, leaving the
register in the same state that it was before the reset.
Instead, detect a reset with the VF_ARQLEN register. When the VF is
reset, the enable bit in this register is cleared, and it stays cleared
until the VF driver processes the reset and re-enables the admin queue.
Because we now deal with multiple registers in the reset and watchdog
tasks, rename the rstat_val variable to reg_val.
Change-ID: Id1df17045c0992e607da0162d31807f7fc20d199
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ran into an issue where PF's VSI type list was different from VF's,
which was resulted in different enum index. The VSI type list can
be different depending on what build flag is used for PF and VF.
The change is to explicitly assign enum index for each VSI type
so that PF and VF always reference to the same VSI type event if the
enum lists are different.
Change-ID: I8c0e5fdb515f324f7964df863a458073cf467e57
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds capability to query and store the CEE DCBX DesiredCfg
and RemoteCfg data from the LLDP MIB.
Added new member "desired_dcbx_config" in the i40e_hw data structure
to hold CEE only DesiredCfg data.
Change-ID: I19c550369594384eaff4cc63e690ca740231195d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This opcode is not required. VFs that program RSS through the firmware
do it by interacting directly with the firmware, and do not need to use
the virtual channel for this functionality.
Change-ID: Iaf17d2600e28ff1b6be8653f2fe9df1facd23b0e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lower level functions are properly reporting errors, and higher-level
functions are correctly responding to errors, but the errors aren't
actually getting through. Typically, the middle-manager function seems
to want to shield its boss from any bad news.
This change fixes a panic if the driver is unable to enable MSI-X or is
unable to acquire enough vectors.
Change-ID: Ifd5787ce92519a5d97e4b465902db930d97b71a1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Keep track of how many times we ask the stack to linearize the
skb because the HW cannot handle skbs with more than 8 frags per
segment/single packet.
Change-ID: If455452060963a769bbe6112cba952e79e944b52
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using something like "ip maddr add ..." to add another unicast mac
address to the netdev, the mac address comes into the set_rx_mode handler
in the multicast list whether it is a unicast or multicast address.
This was confusing the code when it was trying to search for addresses
that needed to be deleted from the VSI, because it was looking for the
VSI unicast address in the netdev unicast list. The result was that a
new unicast address would get added to the VSI list and then immediately
removed, and would never actually make it down into the hardware.
This patch removes the separation from unicast and multicast in the search
for filters to be deleted. It also simplifies the logic a little with a
jump to the bottom of the loop when an address is found. Now it doesn't
matter which netdev list the address is hiding in, we'll check them all.
Change-ID: Ie3685a92427ae7d2212bf948919ce295bc7a874c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During early development, we added the function name to all of the error
strings to make debugging simpler. Now that we've released the driver,
our users should have more comprehensible error messages. So tear the
roof off and give up the __func__. Ow.
Change-ID: I7e1766252c7a032b9af6520da6aff536bdfd533c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a possibility where the asq_last_status could get through without
update and thus report a previous error. I don't think we've actually seen
this happen, but this patch will help make sure it doesn't.
Change-ID: I9e33927052a5ee6ea21f80b66d4c4b76c2760b17
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Christopher Pau <christopher.pau@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rework an if expression to assure there is no type compare problem between
a size and a possible negative number.
Change-ID: I4921fcc96abfcf69490efce020a9e4007f251c99
Reported-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Early addition of new a device id.
Change-ID: I61a8c8556fdf4f5714be4e4089689e374f30293c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The standard way to check if the AQ is enabled is to look at the
count field. So we should only set this field after we have
successfully allocated memory. To do otherwise is to incite
panic among the populace.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain circumstances, we can get an extra VF_RESOURCES message
from the PF driver at runtime. When this happens, we need to parse it
because our VSI may have changed out from underneath us, and that will
affect our relationship with the PF driver.
However, parsing the resources message also blows away our current MAC
address in the hardware struct, usually with all zeros. When this
happens, the next time the interface is opened, it will have no MAC
address and will a) not work and b) complain.
Fix this issue by restoring the current MAC address from the netdev
struct after we parse the resource message.
Change-ID: I6cd1b624fc20432f81dc901166c8de195b8e0e65
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure we have the spinlocks before we clear the ARQ and ASQ management
registers. Also, widen the locked portion and make a sanity check earlier
in the send function to be sure we're working with safe register values.
Change-ID: I34b56044b33461ed780f3d2de8d62826cdf933f9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function i40e_clean_rx_irq() tries to reuse memory pages allocated
from the nearest node. To better support memoryless node, use
numa_mem_id() instead of numa_node_id() to get the nearest node with
memory.
This change should only affect performance.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-30
This series contains updates to i40e and i40evf only.
Vasily Averin provides a couple of rtnl lock/unlock fixes for both i40e
and i40evf.
Shannon provides several updates and fixes, first fixes up a type clash
in i40e_aq_rc_to_posix(), where the error codes are signed values, so we
need to treat them as such. Then fixes up a padding issue where an
extra byte is added in i40e_aqc_get_cee_dcb_cfg_v1_resp to directly
acknowledge the padding. Updated i40e to keep debugfs register read
and writes from accessing outside of the io-remapped space. Added
support and device id for another 20 GbE device.
Jesse fixes the transmit hand workaround code for ARM that was causing
Tx hangs to still occur occasionally when there really was no hang. Then
fixed the receive dropped counter to show up in netstat interface.
Refactor the interrupt enable function since it was always making the
caller add the base_vector from the VSI struct which is already passed
to the function. Fix kbuild warnings found in 0day build infrastructure
by adding a harmless cast to a dev_info(), also fix 32 bit build
warnings found by sparse.
Greg fixed a configuration error that results if a port VLAN is set
for a VF before the VF driver is loaded, so that when the VF driver is
loaded the port VLAN is ignored.
Mitch fixes the use of QOS field consistently in
i40e_ndo_set_vf_port_vlan(). Modified the init timing of the driver
to increase stability on load/unload and SR-IOV enable/disable cycles.
Anjali updates i40e to not collect VEB stats if they are disabled in the
hardware for performance reasons.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tweaks the init timing of the driver just a little bit to
increase stability on load/unload and SR-IOV enable/disable cycles.
First, run the init_task loop a little quicker in order to reduce
overall init time.
Second, stagger the start of the init task based on the device's
PCIe function ID. This lessens the impact on the firmware when a
whole bunch of VFs are initialized simultaneously, e.g. enabling
SR-IOV without the VF driver blacklisted. For single VFs assigned
to VMs this will have no effect as the function ID will always be 0.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new device id and support for another 20Gb device.
Change-ID: Ib1b61e5bb6201d84953f97cade39a6e3369c2cf2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The arm writeback (arm_wb) code is used for kicking the Tx ring to
make sure any pending work is completed even if interrupts are
disabled. It was running when it didn't need to, and not clearing
the ring->arm_wb state after it was set. This caused Tx hangs
to still occur occasionally when there really was no hang.
Fix this by resetting the variable right after it was used.
Change-ID: I7bf75d552ba9c4bd203d40615213861a24bb5594
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The error code sent into i40e_aq_rc_to_posix() are signed values, so we
really need to treat them as such.
Change-ID: I3d1ae0ee9ae0b1b6f5fc424f8b8cc58b0ea93203
Reported-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's possible that while we are waiting for the spinlock, another
entity (that owns the spinlock) has shut down the admin queue.
If we then attempt to use the queue, we will panic.
Add a check for this condition on the receive side. This matches
an existing check on the send queue side.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the driver timeout logic by issuing a writeback
request via a software interrupt to the hardware the first time the
driver detects a hang. The driver was too aggressive in resetting a hung
queue, so back that off by removing logic to down the netdevice after
too many hangs, and move the function to the service task.
Change-ID: Ife100b9d124cd08cbdb81ab659008c1b9abbedea
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a facility to recover the result of a previously run AQ command.
Change-ID: I21afec2c20c1a5e6ba60c7fbfcbedfff78c10e45
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a facility to run AQ commands through the nvmupdate utility in order
to allow the update tools to interact with the FW and do special
commands needed for updates and configuration changes.
Change-ID: I5c41523e4055b37f8e4ee479f7a0574368f4a588
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds wait states to the NVM update state machine to signify when
waiting for an update operation to finish, whether we're in the middle
of a set of Write operations, or we're now idle but waiting.
Change-ID: Iabe91d6579ef6a2ea560647e374035656211ab43
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds a new GetStatus command so that the NVM update tool can query
the current status instead of doing fake write requests to probe for
readiness.
Change-ID: I671ec6ccd4dfc9dbac3a03b964589d693fda5cd8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the writeback descriptor buffer was previously created, this gives it
to the AQ command request to be used to save the results.
Change-ID: I8c8a1af81e6ebed6d0a15ed31697fe1a6c4e3708
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the ability to save the AdminQ write back descriptor if a
caller supplies a buffer for it to be saved into.
Change-ID: I3d1301d26360b39a2d66dc8569e851f54133a3af
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version and update the copyright year for i40evf.
Change-ID: Iddb81b9dba09f0dc57ab54937b5821ecdd721ff6
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the CEE TLV status returned by firmware to allow drivers to dump that
for debug purposes.
Change-ID: Ie3c4cf8cebabee4f15e1e3fdc4fc8a68bbca40ee
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were quite a few issues when the wrong defines were getting used
in the VF driver. This patch fixes the code where PF driver registers
were getting used for VF driver, and also removes the registers that are
not being used from the VF register file.
Change-ID: If116a9730112950d006eb8ec763998fc914cc839
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use CTLN1 instead of CTLN for the VF relative register space.
Change-ID: Iefba63faf0307af55fec8dbb64f26059f7d91318
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds capability to update per VEB per TC statistics and dump
it via ethtool. It also adds a structure to hold VEB per TC statistics.
The fields can be filled by reading the GLVEBTC_* counters.
Change-ID: I28b4759b9ab6ad5a61f046a1bc9ef6b16fe31538
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports offloading of outer UDP TX and RX checksum for tunneled
packets. This patch exposes the support and leaves it enabled by
default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 uses the admin queue to configure RSS. This patch adds the necessary
flow changes to configure RSS through AQ. It also adds the separate VMDQ2
lookup tables and hash key programming for X722.
X722 also exposes a different set of PCTYPES for RSS, this patch
accommodates those changes.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the i40e and i40evf register.h file with the registers for X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does the firmware API update to support the new X722 device.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add capabilities flags specific to X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding device ids for new hardware X722
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use macros for abstracting (1 << foo) to BIT(foo)
and (1ULL << foo64) to BIT_ULL(foo64) in order to match
better with kernel requirements.
NOTE: the adminq_cmd.h file was not modified on purpose because
of the dependency upon firmware for that file.
Change-ID: I73ee2e48c880d671948aad19bd53ca6b2ac558fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up a little confusion in reporting error status in phy and fcoe
setup error reports by separating the return status from the AQ error.
Add two decoder functions to make this easier.
Change-ID: I960bcdeef3978a15fec1cdb5eff781d5cbae42fb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store off the PF's API version, then use it to determine whether or not
to send it our capabilities. Change the version checking to allow for PF
drivers with lower API versions than our current version, so we can
still talk to PF drivers over the 1.0 API.
Change-ID: I8edc55d1229c7decf0ed3f285a63032694007c2e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The most common type of reset that the VF will encounter is a PF reset
that cascades down into a VF reset for each VF. In this case, the VF
will always be assigned the same VSI and recovery is fairly simple.
However, in the case of 'bigger' resets, such as a Core or EMP reset,
when the device is reinitialized, it's probable that the VF will NOT get
the same VSI. When this happens, the VF will not be able to recover, as
it will continue to request resources for its original VSI.
Add an extra state to the admin queue state machine so that the driver
can re-request its configuration information at runtime. During reset
recovery, set this bit in the aq_required field, and fetch the (possibly
new) configuration information before attempting to bring the driver
back up. Since the driver doesn't know what kind of reset it has
encountered, this step is done even for a PF reset, but it doesn't hurt
anything - it just gets the same VSI back.
Change-ID: I915d59ffb40375215117362f4ac7a37811aba748
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we've rolled the virtual channel API version to 1.1, add some
macros to test what version is being used by our partner in crime. For the
VF, add some macros to determine what our device capabilities are.
Change-ID: I79f6683d4c23bd76a8ad9fd492776fcc1208e1dc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To prepare for the changes coming up in the X722 device and future
devices, the virtual channel interface has to change slightly. The VF
driver can now report what its capable of supporting, which then informs
the PF driver when it sends the configuration information back to the
VF.
A 1.1 VF driver on a 1.0 PF driver should not send its capabilities.
Likewise, a 1.1 PF driver controlling a 1.0 VF driver should not expect
or depend upon receiving the VF capabilities.
All other aspects of the API are unchanged.
Change-ID: I530cc55f107edd1ee8bdf95830aa90b87854058a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Anjali Singhai <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the switch statement for dynamic interrupt throttling
and adds a default case. With this patch, we check the latency setting
instead of the current ITR settings and the included refactor improves
performance.
Without this patch, the ITR setting would never change dynamically, and
there was no default.
Change-ID: Idb5a8a14c7109ec47c90f6e94bd43baa17d7ee37
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump.
Change-ID: I84573d9fa51effc5b29bf5b8c74e3cc8b2673f48
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_add_pd_table_entry() routine is being modified to handle both
cases where a backing page is passed and where backing page is allocated
in i40e_add_pd_table_entry().
For PBLE resource management, it is more efficient for it to manage its
backing pages. For VF, PBLE backing page addresses will be send to PF
driver for PBLE resource.
The i40e_remove_pd_bp() is also modified to not free pre-allocated pages and
free only ones which were allocated in i40e_add_pd_table_entry().
Change-ID: Ie673f0403f22979e9406f5a94048dceb91bcf9a8
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During close, all of the MAC filters are cleared, so the driver would be
unable to receive unicast packets after being closed and reopened.
Add the adapter's "hardware" MAC address filter in open, not init. This
ensures that the correct filter is present each time.
Change-ID: I51a11e9c1200139dab6f66a5353bd38c7d26f875
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to an inverted conditional, the driver was marking all of its MAC
filters for deletion every time set_rx_mode was called. Depending upon
the timing of the calls to set_rx_mode and the processing of the admin
queue, the driver would (accidentally) end up with a varying number of
functional filters.
Correct this logic so that MAC filters are added and removed correctly.
Add a check for the driver's "hardware" MAC address so that this filter
doesn't get removed incorrectly.
Change-ID: Ib3e7c4a5b53df6835f164fe44cb778cb71f8aff8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the necessary updates to i40e_adminq_cmd.h.
Change-ID: Ib031c86cc6cab78e5aa44c64d8ce5474be8d7e42
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver currently only maps TX and RX queues to a single MSI-X vector
per queue pair if there are exactly enough vectors for this.
Unfortunately, if we have too many vectors it will fail and allocate
queues to vectors in a suboptimal manner. Change the condition check to
allow for excess vectors. In this case, the extras just won't be used.
Change-ID: I23e1e2955c64739c86612db88a25583e6a7e0b17
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a prefetch for the next Tx descriptor to be used when we know
there are more coming.
Change-ID: Ibb9acab11d508eec2db7da795df74debc16eeacb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Flex10 device/function capability has been upgraded to include
information needed to support Flex-10 configurations. This patch adds new
fields to the i40e_hw_capabilities structure and updates
i40e_parse_discover_capabilities functions to extract them from the AQ
response. Naming convention has changed to use flex10 mode instead of
existing mfp_mode_1.
Change-ID: I305dd888866985a30293acb3fb14fa43ca6b79ea
Signed-off-by: Pawel Orlowski <pawel.orlowski@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the driver can dynamically enable/disable FD ATR and SB features,
these stats help keep track of the current state and along with
fd_flush count provide a means to debug what could be going on
with the flow director filters. This will take away the need for
being verbose in our debug logs with respect to FD.
Change-ID: I29224f750fe6602391043655d18996570720377d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver will only configure as many queues as there are available
CPUs, up the maximum number of queues. However, it always configures
RSS as though it is using the maximum number of queues. This can cause
the device to drop a lot of RX traffic, as the packets get assigned to
nonfunctional queues.
Fix this by only configuring RSS with the number of active queues.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Down was requesting queue disables, but then exited immediately
without waiting for the queues to actually disable. This could
allow any function called after i40evf_down to run immediately,
including i40evf_up, and causes a memory leak.
Removing the whole reinit_locked function is the best way
to go about this, and allows for the driver to handle the
state changes by requesting reset from the periodic timer.
Also, add a couple WARN_ONs in slow path to help us recognize
if we re-introduce this issue or missed any cases.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver doesn't use the time_stamp member to determine if there is a
tx_hang any more. There really isn't any point to the variable at all
so just remove it. It was left over from a previous tx_hang design.
Change-ID: I4c814827e1bcb46e45118fe37acdcfa814fb62a0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Inlining these functions gives us about 15% more 64 byte packets per
second when using pktgen. 13.3 million to 15 million with a single
queue.
Also fix the function names in i40evf to i40evf not i40e while we are
touching the function header.
Change-ID: I3294ae9b085cf438672b6db5f9af122490ead9d0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric added support for skb->xmit_more in i40e, this ports that into
i40evf as well.
Support skb->xmit_more in i40evf is straightforward; we need to move
around i40e_maybe_stop_tx() call to correctly test netif_xmit_stopped()
before taking the decision to not kick the NIC.
Change-ID: Idddda6a2e4a7ab335631c91ced51f55b25eb8468
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no need for a counter so remove the TODO comment.
Change-ID: I3321dda04934c4f5fda9b279ab666192bda44214
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a 3rd dynamic filter counter to track Tunneled ATR hits separately.
Ethtool port stat "fdir_atr_tunnel_match"
Change-ID: Idd978b6db2a462b5722397cd2ffd04ef055f8655
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Without this, RSS would have done inner header load balancing. Now we can
get the benefits of ATR for tunneled packets to better align TX and RX
queues with the right core/interrupt.
Change-ID: I07d0e0a192faf28fdd33b2f04c32b2a82ff97ddd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
None of those drivers uses last_rx for its own needs.
See 4dc89133f4 ("net: add a comment on
netdev->last_rx") for reference.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the 8 bytes of the WR_CSR_PROT field returned as part of the get
device/function capabilities AQ command.
Change-ID: Ifcaeea2ff29885fa769e4f384c7db88a25e8afd0
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The aq_pending field in the adapter structure is actually redundant with
the current_op field. Remove the aq_pending field and expunge all traces
of it from the official record. This simplifies the code significantly,
especially in the virtual channel completion routine.
Change-ID: Ib2957c8c19882bd0cecc6fcd133912c24b46a1ff
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Not sure how this slipped through. Cosmetic change only.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update i40e and i40evf to use dma_rmb. This should improve performance by
decreasing the barrier overhead on strong ordered architectures.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor VF RSS code to allow RSS on a single queue and eliminate
the need for the next_queue function.
Change-ID: I9253bad96b7f542ee7036e15636db0e5d58d8ef2
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC filter list is protected by a critical task bit, and the VLAN
list should be protected as well. This prevents list corruption if the
watchdog happens to run at the same time as a VLAN filter is being added
or deleted.
Change-ID: Ia4867cebbbb046a1f38012771b288a634ca5882b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If transmit VLAN HW offloads are disabled then the network stack sends up
an skb with the protocol set to 8021q. In that case to get the correct
checksum offloads we have to reset the skb protocol to the encapsulated
ethertype.
Change-ID: I903d78533de09b1c5d3ec695ee1990dd0fa5dd0d
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the skb allocation fails we should not continue using the skb
pointer. Breaking out at the point of failure means that at the next
RX interrupt the driver will try the allocation again.
Change-ID: Iefaad69856ced7418bfd92afe55322676341f82e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Inner protocol being UDP should not stop us from verifying Outer UDP
checksum correctness.
If the Outer protocol is not UDP (NVGRE) we should not be doing a UDP
checksum check. If the packet has zero checksum, skip checksum check.
Change-ID: Ie7f153feb276a59f66a54a0938901b2c0a8100fa
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Customers reported that the firmware version information from i40evf
is unlike that of ixgbevf and was causing problems with their scripts.
To resolve this, populate the field to align with ixgbevf.
Change-ID: I9f4e24f6a76cd819bbe07087aab2b74f715ec103
Reported-by: Sourav Chatterjee <sourav.chatterjee@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call the netdev carrier off and TX disable functions first, before other
shutdown operations. This stops the stack from hitting us with
transmits while we're shutting down. Additionally, disable NAPI before
disabling interrupts, or the interrupt might get re-enabled
inappropriately. Finally, remove the call to netif_tx_stop_all_queues,
as it is redundant - the call to netif_tx_disable already did the same
thing.
Change-ID: I8b2dd25231b82817746cc256234a5eeeb4abaccc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VF interface is closed, we cannot immediately free our rings
and RX buffers, because the hardware hasn't yet stopped accessing this
memory. This shows up as a panic or memory corruption when the device is
brought down while under heavy stress.
To fix this, delay releasing resources until we receive acknowledgment
from the PF driver that the rings have indeed been stopped. Because of
this delay, we also need to check to make sure that all of our admin
queue requests have been handled before allowing the device to be
opened.
Change-ID: I44edd35529ce2fa2a9512437a3a8e6f14ed8ed63
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new devices need a new device ID some other defines to
handle the new 20G speed for KR2.
Change-ID: I03f717e364afe59657e8c9ce5ffaad856b4b21df
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump PF version to 1.2.37 and VF version to 1.2.25
Change-ID: I0287a750408250dc055c03e1f744fd5f0caefd68
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug introduced in the force writeback code, where the interrupt
rate was set to 0 (maximum) by accident.
The driver must correctly set the NOITR fields to avoid ITR update
as a side effect of triggering the software interrupt.
Change-ID: I290851ae04ef3811c43aab5ee33242029f26c1a3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset occurs when the netdev is closed, the reset task will hang in
napi_disable, causing deadlocks and general grumpiness.
Check to make sure the device is actually running before stopping
everything. This allows the reset task to complete and have a real good
time.
Change-ID: Iaaea84acbcb9b3810c216b14c3326e4287b75b58
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 1.2.12 and i40evf to 1.2.6.
Change-ID: I641871da3a9abd396b28eda5744a4d68493c1400
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Performance can be improved a bit by imitating ixgbe and using
prefetch to get us the next Tx descriptor.
Change-ID: Ice7ffd4cd0ce87c35295059bdb7972a7f53723aa
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use l4_tunnel type generically to keep code flow simple.
Change-ID: Ic52287e3b1ca4204e6b6e13431890c1a6ae9c422
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A sparse complaint in i40e_debug_aq in a funky buffer write goes away by
straightening out the code out to something less convoluted.
Also fix some other sparse warnings while we are at it, making some
functions static and using NULL instead of 0.
Change-ID: I93907534fe1f1f675830774b3d14ecf1c6ffc9a0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.11 and i40evf to 1.2.5
Change-ID: Ie13375941606b0a027e5b5dbc235f5f5f03b75c8
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some double blank lines and un-split a function declaration that all
fits on one line. Also make i40e_get_priv_flags static.
Change-ID: I11b5d25d1153a06b286d0d2f5d916d7727c58e4a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
0x2A is the NVM version so it has useful data but it is per image
version every image can have a different one. 0x18 is the dev starter
version which all the images for release will have the same version.
Of the two 0x18 is more useful and is what should be displayed.
Change-ID: Idf493da13a42ab211e2de0bef287f5de51033cca
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 1.2.10 and i40evf to 1.2.4
Change-ID: I48aa64df05fcc8356e7026f3a9e69ecf78d0c785
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an extra check to make sure that the indirection table pointer is
valid before dereferencing it.
Change-ID: I698adbf3daff03081d01f489dc95a9f1ad8b12f1
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were missing a few packet types for VXLAN offload. This patch fixes
that.
Change-ID: I4b23aa0b08e40ed49d0df6c49a5ed9f2009b44ce
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Include the FW build number in the formatted FW version string. In order
to fit within ethtool's 32 character limit, the etrack's unused high order
bits are trimmed as is the leading 0 for the NVM version. This leaves
us with 2 character left for if/when the etrack id goes to 5 hex chars
and the NVM major number goes to 2 chars.
Change-ID: Icb004c4b9b14a2f54dd200b467fcc1d7b9297308
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were checking the outer Protocol flags and deciding the flow for
inner header. This patch fixes that.
This fixes the Tx checksum offload for TCP/IPv6 over vxlan.
Change-ID: I837aaea921d34f71b24c2bc32aaadea5001ddf78
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was having some issues with false Tx hang detection. This
makes the driver a little more direct with the checks for progress
forward by directly checking the head write back address and tail register
when determining progress. This avoids Tx hangs where the software
gets behind, because we are directly checking hardware state when
determining hang state.
Change-ID: I774f0e861c9e8ab5ccb213634100fe15440ae24a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware has some limitations the driver needs to adhere to,
that we found in extended testing.
1) no more than 8 descriptors per packet on the wire
2) no header can span more than 3 descriptors
If one of these events occurs, the hardware will generate an internal
error and freeze the Tx queue.
This patch linearizes the skb to avoid these situations.
Change-ID: I37dab7d3966e14895a9663ec4d0aaa8eb0d9e115
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.9 and i40evf 1.2.3
Also update the copyright year.
Change-ID: I345d777e94abd0acffe6a28793f675d251a86299
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the netdev name to the VF misc vector name. Without
this patch, all the interrupts show the same info, so it difficult to
distinguish them.
Change-ID: I247828697e1373ecfb5f8dc1bc9618e98a7f4942
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Copy setting from ethtool to the HW specific struct to actually
enable prints. Change print from i40e to i40evf to differentiate
drivers in bare metal scenarios.
Also update the copyright year.
Change-ID: I06fee26247299a08f2e1c70fc811a9ea0931c4dd
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a requested speed variable to the link_status struct to store the
last speeds we requested from the firmware (the speeds the FW will be
advertising with if autoneg is enabled).
Use the advertised speed settings in get_settings in ethtool now that
we have it. Also set the requested speed settings in set_settings in
ethtool as they are requested and initialize them in probe based on what
the firmware remembers as the last requested speeds.
To accommodate some longer lines in this new code, and improve
readability I have added two functions i40e_get_settings_link_up
and i40e_get_settings_link_down which get_settings now calls first.
It then does all of the settings that happen regardless of link
state. Some PHY types that supported the same settings were also combined.
Also update the copyright year.
Change-ID: Ica0c5ac81b6069ea6a7406fce7482f7816d4455c
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function i40e_debug_aq() prints information helpful in debugging
admin queue commands, but it doesn't do so correctly on big endian machines.
This patch adds the appropriate LExx_TO_CPU wrappers for big endian
architectures.
Also update the copyright year.
Change-ID: I4b2dc229ed5bf6dfe35632a58cddf53c21aff4b0
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Under rare circumstances, after a reset, set_rx_mode might get called
while the watchdog is running, which will cause a deadlock on the
critical section lock. To correct this, add a counter and give up trying
to get the lock after fifty tries. Log a message if this happens but
don't take any other action. Because this happens after a reset, all of
the Rx filters are still in place and the device won't lose
connectivity.
We can also get stuck during shutdown, if the PF has stopped communicating
with us, or if a reset is occurring. If we can't get the lock after a reasonable
amount of time, just error out. Something else bad is happening anyway, so
adding this filter is the least of our concern right now.
Change-ID: I159731e2a82a06b389ee31b34ce336548e05baa0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change to the shutdown flow messed up the reset flow. Since
i40evf_down now holds the critical section lock, we cannot call it from
the reset handler, which also holds the lock. To do so causes a deadlock
accompanied by wailing and gnashing of teeth. This is easily triggered
by running an ethtool self-test on the PF device.
Instead, we move the relevant portions of i40evf_down into the reset
handler and bend them to our will. Additionally, we can optimize the
reinit path by not deleting the MAC and VLAN filters and then adding
them back again. Instead, we just set the 'add' flag and let the
watchdog resynchronize the filter list with the PF driver. We also
reword a few messages to make them more consistent with the rest of the
driver.
Change-ID: I03dd92ae736f7719fca3564b12a2cf9b98c6cb18
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When closing the interface, disable NAPI polling before any other
activities. This fixes an occasional panic during close caused by the
driver trying to delete and clean rings at the same time.
Change-ID: Ib4d427b13d310258ea85b248d535da70ecf0c1e9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.8 and i40evf to 1.2.2
Change-ID: I64f47c3367ea8ff2a53068e895d7a1f60726c871
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An_enable was never used only set so lets remove it. The function
update_link_info only did two things, call get_link_info and set
an_enabled. Therefore we should also remove update_link_info and
change all references to it to get_link_info.
Change-ID: Ie3022680fa7a94bfd495a4f5fc76a73701d85569
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some registers have been removed so take them out and
stop updating and looking at them.
Change-ID: I33da922c8de993a94dd8b8d8a2ae2146b8ca1a27
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Until the time a more robust versioning scheme is needed/implemented all
established virtual channel opcode values should remain consistent between
updates to the opcode enum.
This patch repositions I40E_VIRTCHNL_OP_CONFIG_RSS to the end of the enum. In
its current position this opcode displaces the initial value of
I40E_VIRTCHNL_OP_EVENT and will cause PF/VF compatibility issues.
Going forward the expectation is either:
a) All future opcode additions will be added as the last element of the
enum. Once VF drivers start making use of the new commands the virtual
channel version will need to be incremented and drivers will need to
implement a simple version check whereby VF drivers can only load on
PFs with a >= version.
b) or, if needed, design and implement a more complicated API
negotiation capability.
In either case PF drivers should always maintain backwards compatibility with
earlier VF driver versions.
Change-ID: Ie245daa09a231b6680ed793d648bdcc76caefe58
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Split the receive hot path code into two, one for packet split and one
for single buffer. This improves receive performance since we only need
to check if the ring is in packet split mode once per NAPI poll time,
not several times per packet. The single buffer code is further improved
by the removal of a bunch of code and several variables that are not
needed. On a receive-oriented test this can improve single-threaded
throughput.
Also refactor the packet split receive path to use a fixed buffer for
headers, like ixgbe does. This vastly reduces the number of DMA mappings
and unmappings we need to do, allowing for much better performance in
the presence of an IOMMU.
Lastly, correct packet split descriptor types now that we are actually
using them.
Change-ID: I3a194a93af3d2c31e77ff17644ac7376da6f3e4b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes indentation issue and error found in argument
reported by static analysis. Without this patch, sparse and other
static analysis errors will be found.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a call to u64_stats_init to Rx setup.
This done in order to avoid lockdep errors with seqcount on newer kernels.
Change-ID: Ia8ba8f0bcbd1c0e926f97d70aeee4ce4fd055e93
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch forces Tx descriptor writebacks on ITR by kicking
off the SWINT interrupt when we notice that there are non-cache-aligned
Tx descriptors waiting in the ring while interrupts are disabled
under NAPI.
Change-ID: dd6d9675629bf266c7515ad7a201394618c35444
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop the watchdog during shutdown. Failing to do this causes a log full
of admin queue errors and the occasional hang when the system is shut
down.
Change-ID: Ib2fd11213cca2fa589eb68577e86b1000c23c250
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Occasionally on shutdown, the FW will hand us a bunch of messages filled
with zeros, which can cause us to spin trying to handle them. Just
ignore these and get on with shutting down.
Change-ID: I347e9648f7153ad5a7b7e0847b87f7aad5f3e0da
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the module is being unloaded, don't wait for the PF to politely
handle all of our admin queue requests, as that might take forever with
a lot of VFs enabled. Instead, just stop everything and request a VF
reset.
When the original shutdown code was written, VF resets were unreliable,
so we avoided them. But with production hardware and firmware, and the
1.x PF driver, this is no longer the case.
This fixes a potential multi-minute delay on driver unload, VF disable,
or system shutdown.
Change-ID: Ib43d6d860ef6b9b8f26e8dce0615a0302608c7d9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.6 and i40evf to 1.2.0 version.
Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add parsing and reporting of iSCSI capability for a given device or
function.
Also add support for iSCSI partition type with DCB in NPAR mode.
In this mode it is expected that software would configure both the LAN
and iSCSI traffic classes for the iSCSI partition; whereas all the NIC
type partitions will use LAN TC (TC0) only.
Hence, the patch enables querying of DCB configuration in MFP mode and
configures TCs for iSCSI partition type.
Though NIC type partitions may not have more than 1 TC enabled for them
the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED
will be set/reset on all the partitions based on number of TCs on the
port. This is required as in DCB environment it is expected that all
traffic will be priority tagged.
Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up NVM config read and write data structs.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add struct size checks to many of the indirect structs and a few
command structs that were left out previously.
Change-ID: I7810b9af0f04e3ced670639f8671daf7df9b3f4d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.5 and i40evf to 1.0.7.
Change-ID: I622556829056e3ed42d3b9d285fc5ffb693b21cc
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increase ASQ timeout for some scenarios with multi-function devices
Change-ID: I2d7655b19e6c6f9a7ad04deacb106ca8d53886db
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several little tweaks to keep FW, SV, and SW in line together
- Remove the unused and deprecated
i40e_aqc_opc_debug_modify_internals
- Add define for iSCSI capability
- Fix queue mask size
- Adjust i40e_aqc_oem_param_change for ease-of-use
Change-ID: I51f250b367912968a7cec61b3a68110d9796e914
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kamil Kacperski <kamil.kacperski@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in NPAR mode the driver instance might be controlling the base
partition or one of the other "fake" PFs. There are some things that
can only be done by the base partition, aka partition_id 1. This code
does a bit of work to find how many partitions are there per port and
what is the current partition_id.
Change-ID: Iba427f020a1983d02147d86f121b3627e20ee21d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some versions of the firmware, the VF admin send queue may become
stalled. In this case, the easiest solution is to just place another
descriptor on the queue; the firmware will then process both requests.
The early init code already accounts for this, but the runtime code does
not. In the watchdog task, check for the stall condition, and if it's
found, send our API version to the PF. When the PF replies, just ignore
the reply.
Change-ID: I380d78185a4f284d649c44d263e648afc9b4d50c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't enable vector 0 in the ISR, just schedule the adminq task and let
it enable the vector. This prevents the task from being called
reentrantly. Make sure that the vector is enabled on all exit paths of
the adminq task, including error exits.
Change-ID: I53f3d14f91ed7a9e90291ea41c681122a5eca5b5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is always a possibility that MSI-X interrupts can get lost. To
keep this problem from stalling the driver, we fire all of our MSI-X
vectors during the watchdog routine. However, we should not fire the
traffic vectors when the interface is closed. In this case, just fire
vector 0, which is used for admin queue events.
As a result, we do not enable the interrupt cause for vector 0. This
can cause the admin queue handler to be called reentrantly, which
causes a scary "critical section violation" message to be logged,
even though no real damage is done.
Change-ID: Ic43a5184708ab2cb9a23fca7dedd808a46717795
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we're using VLANs and communications with the PF fail during
shutdown, we will leak memory because not all of the VLAN filters will
be removed. To eliminate this possibility, go through the list again
right before the module is removed and delete any leftover entries.
Change-ID: Id3b5315c47ca0a61ae123a96ff345d010bc41aed
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF driver is running in the host, the shutdown code is completely
broken. We cannot wait in our down routine for the PF to respond to our
requests, as its admin queue task will never run while we hold the lock.
Instead, we schedule operations, then let the watchdog take care of
shutting things down. If the driver is being removed, then wait in the
remove routine until the watchdog is done before continuing.
Change-ID: I93a58d17389e8d6b58f21e430b56ed7b4590b2c5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These messages may be triggered during normal init of the driver if the
PF or FW take a long time to respond. There's nothing really wrong, so
don't freak people out logging messages.
If the communication channel really is dead, then we'll retry a few
times and give up. This will log a different more scary message that
should cause consternation. This allows the user to more easily detect a
genuine failure.
Change-ID: I6e2b758d4234a3a09c1015c82c8f2442a697cbdb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These functions are redundant and duplicate functionality found in
i40evf_free_all_[tx|rx]_resources.
Change-ID: Ia199908926d7a1a4b8247f75f89b5da24c9b149c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Inline functions are preferred over macros when they can be used
interchangeably.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Decoding the AQ return code is great except when the AQ send timed out
and there's no return code set. This changes the handy decoder
interface to help catch and properly report the condition as a useful
errno rather than returning a misleading '0'.
Change-ID: I07a1f94f921606da49ffac7837bcdc37cd8222eb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't bother trying to set a smaller timeout on the polling,
just simplify the code and always use the max limit. Also,
rename a variable for clarity and fix a comment.
Change-ID: I0300c3562ccc4fd5fa3088f8ae52db0c1eb33af5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The nvm_semaphore_wait field is set but never used, so let's
just get rid of it.
Change-ID: I2107bd29b69f99b1a61d7591d087429527c9d8fa
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just to be sure, add a range check to avoid any possible
array index-out-of-bound issues.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Change-ID: I9323bee6732c2a47599816e1d6c6b3a1f8dcbf54
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM update operations take time finish asynchronously, and follow-on
update requests need to wait for the current one to finish. Early
firmware didn't handle this well, so the code had to track the busy state.
The released firmware handles the busy state correctly, returning
I40E_AQ_RC_EBUSY if an update is still in progress, so the code no longer
needs to track this.
Change-ID: I6e6b4adc26d6dcc5fd7adfee5763423858a7d921
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.
It modifies drivers implementation of set/get_rxfh accordingly.
This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.
User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.
Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple VFs attempt to initialize simultaneously, the firmware may
delay or drop messages. Make the init code more adept at handling these
situations by a) reinitializing the admin queue if the firmware fails to
process a request, and b) resending a request if the PF doesn't answer.
Once the request has been sent again, the PF might end up getting both
requests and send the configuration information to the driver twice.
This will cause the VF to complain about receiving an unexpected message
from the PF. Since this is not fatal, reduce the warning level of the
log messages that are generated in response to this event.
Change-ID: I9370a1a2fde2ad3934fa25ccfd0545edfbbb4805
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is useful for future expansion when new VF MAC types get
added. It helps with cleaning up VF driver flow.
Change-ID: Ibe1eeb71262a3a40f24a1c5409436bdc3411da7f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Virtual Channel OP event opcode for CONFIG_RSS, so that the
Virtual Channel state machine can properly decipher status change events.
Change-ID: I09939c7aa380147f60c49fd01ef2e27d0dc1c299
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This message really doesn't give any useful information and ends up
getting printed every service_task loop in the Linux driver, filling the
logfile with noise when AQ tracing is enabled. This patch simply removes
the noise.
Change-ID: I30ad51e6b03c7ad12a7d9c102def0087db622df3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the if part of this statement contains a break, there's no reason
for the else. Clean up the code and make it more obvious that the delay
happens each time through the loop.
Change-ID: I9292eaf7dd687688bdc401b8bd8d1d14f6944460
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most of the null-checking in this driver is of the style if (!foo),
except these few. Make these checks consistent with the rest of the
code.
Change-ID: I991924f34072fa607a1b626a8b3f1fa5195d43e9
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is the result of running checkpatch on the i40evf driver with
the --strict option. The vast majority of changes are adding/removing
blank lines, aligning function parameters, and correcting over-long
lines.
The only possible functional change is changing the flags member of the
adapter structure to be non-volatile. However, according to the kernel
documentation, this is not necessary and the volatile should be removed.
Change-ID: Ie8c6414800924f529bef831e8845292b970fe2ed
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
No code changes. Update comments to match actual function declarations.
Change-ID: Ib830d2f154ee917a104955c0914267fc98f3d2c8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Overloading the msg_size field in the arq_event_info struct is just a
bad idea. It leads to repeated bugs when the structure is used in a
loop, since the input value (buffer size) is overwritten by the output
value (actual message length).
Fix this by splitting the field into two and renaming to indicate the
actual function of each field.
Since the arq_event struct has now changed, we need to change the drivers
to support this. Note that we no longer need to initialize the buffer size
each time we go through a loop as this value is no longer destroyed by
arq processing.
In the process, we also fix a bug in i40evf_verify_api_ver where the
buffer size was not correctly reinitialized each time through the loop.
Change-ID: Ic7f9633cdd6f871f93e698dfb095e29c696f5581
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's kind of silly to configure and attempt to use a bunch of queue
pairs when you're running on a single (virtual) CPU. Instead of
unconditionally configuring all of the queues that the PF gives us,
clamp the number of queue pairs to the number of CPUs.
Change-ID: I321714c9e15072ee76de8f95ab9a81f86ed347d1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In early init, if we get an unexpected message from the PF (such as link
status), we just kick an error back to the init task, causing it to
restart its state machine and delaying initialization.
Make the early init AQ message receive code more robust by handling
messages in a loop, and ignoring those that we aren't interested in.
This also gets rid of some scary log messages that really didn't
indicate a problem.
Change-ID: I620e8c72e49c49c665ef33eeab2425dd10e721cf
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The interrupt throttle rate minimum is actually 2us, so
fix that define and while we are there, remove some unused defines.
Change some strings in the function to be a bit less wrappy, and
express the correct limits.
Change-ID: I96829bbc77935e0b57c6f0fc1439fb4152b2960a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code was polling the firmware tail register for completion every
10 microseconds, which is way faster than the firmware can respond.
This changes the poll interval to 1ms, which reduces polling CPU
utilization, and the number of times we loop.
The maximum delay is still 100ms.
Change-ID: I4bbfa6b66d802890baf8b4154061e55942b90958
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add 10G-Base-T support in i40evf.
Change-ID: I98a1c3138d7d6572fe7903a7c1c4692cae3260d5
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we receive an admin queue message, the msg_size field in the event
struct gets overwritten. Because of this, we need to reinit the field
each time we go through the loop. Without this we may receive truncated
messages due to the firmware thinking we have insufficient buffer size.
Change-ID: I21dcca5114d91365d731169965ce3ffec0e4a190
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the Documentation/timers/timers-howto.txt it is preferred to use
usleep_range() instead of udelay() if the delay value is > 10us in
non-atomic contexts.
So, replacing all the instances of udelay() with 10 or greater than 10
micro seconds delay in the driver and using usleep_range() instead.
Change-ID: Iaa2ab499a4c26f6005e5d86cc421407ef9de16c7
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is one small step in making the indentation more consistent. If
we truly want to align values, then use tabs rather than spaces.
Change-ID: I12368bc77a52f296d1843fdcb67201a7d7cd4749
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Bump i40e version to 1.0.11 and i40evf version to 1.0.5.
Change-ID: I63a60fa2efe82aae87a8a3095f43218db57d46ce
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Set skb->csum_level instead of skb->encapsulation when indicating
CHECKSUM_UNNECESSARY for an encapsulated checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump versions for i40e to 1.0.4 and i40evf to 1.0.1.
Change-ID: I960c04da2c91bdf1d02f8e5011e68c34a634122d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are seeing situations where the driver sees a hang with less than 4
desc pending, if the driver chooses to ignore it the queue progresses
forward and the stack never experiences a real hang.
With this patch we will log a stat when this situation happens
"tx_sluggish" will increment and we can see some more details
at a higher debug level. Other than that we will ignore this
particular case of Tx hang.
Change-ID: I7d1d1666d990e2b12f4f6bed0d17d22e1b6410d5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is at least one case in the Firmware API where the response to a
command changes the buffer size field in the AQ descriptor to a larger
number than what the request's buffer size started as. This is in addition
to setting an error flag and is in order to tell the requester how much
larger a buffer is required for the answer. We need to be sure not to
use that number when dumping the contents of the data buffer because it
can send us into the weeds and generate an invalid pointer exception.
This patch adds a max buffer size parameter to the print helper to be
sure the code knows when to stop.
Change-ID: Ib84f7ed72140fe9d600086d8f2002fc5d8753092
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
Fix this by using vlan_get_protocol() helper.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Removing VF driver during device still in reset caused guest OS panic.
in the i40evf_remove(), we're trying to clean mac_filter_list which has
not been initialized since the device is still stuck at the reset.
The change is to initialize the filter_list before setting any task.
Change-ID: I8b59df7384416c7e6f2d264b598f447e1c2c92b0
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is loaded and then unloaded before the interface is
brought up, then it will allocate a MAC filter entry and never free it.
To fix this, on unload, run through the mac filter list and free all the
entries. We also do this during reset recovery when the driver cannot
contact the PF and needs to shut down completely.
Change-ID: I15fabd67eb4a1bfc57605a7db60d0b5d819839db
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory leak. Driver was allocating memory for queue vectors on
init but not freeing them on shutdown. These need to be freed at two
different times: during module unload, and during reset recovery when
the driver cannot contact the PF driver and needs to give up.
Change-ID: I7c1d0157a776e960d4da432dfe309035aad7c670
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in an adapter state check to prevent re-arming watchdog timer after
i40evf_remove has been called and timer has been deleted.
Change-ID: I636ba7c6322be8cbf053231959f90c0a2d8d803a
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously defined state I40E_VFR_VFACTIVE uses bit 1 which is now set to
"reserved." Update the state checks to also include I40E_VFR_COMPLETED.
This change will allow the VF to work with both existing and future PFs.
Change-ID: Ifd1d34f79f3b0ffd6d2550ee4dadc55825ff52f8
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was converted to use snprintf everywhere but this one function.
Just use snprintf, instead of sprintf.
Also a small spelling correction in a comment.
Change-ID: I59d45f94a52754c7b4cd6034df9a61d8132b7f77
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes the AQTX answer comes back with no data, but we still want to print
the descriptor that got written back.
Change-ID: I5f734d99b4c95510987413893f0a34626571d474
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jingjing Wu