The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in NPAR mode the driver instance might be controlling the base
partition or one of the other "fake" PFs. There are some things that
can only be done by the base partition, aka partition_id 1. This code
does a bit of work to find how many partitions are there per port and
what is the current partition_id.
Change-ID: Iba427f020a1983d02147d86f121b3627e20ee21d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some versions of the firmware, the VF admin send queue may become
stalled. In this case, the easiest solution is to just place another
descriptor on the queue; the firmware will then process both requests.
The early init code already accounts for this, but the runtime code does
not. In the watchdog task, check for the stall condition, and if it's
found, send our API version to the PF. When the PF replies, just ignore
the reply.
Change-ID: I380d78185a4f284d649c44d263e648afc9b4d50c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't enable vector 0 in the ISR, just schedule the adminq task and let
it enable the vector. This prevents the task from being called
reentrantly. Make sure that the vector is enabled on all exit paths of
the adminq task, including error exits.
Change-ID: I53f3d14f91ed7a9e90291ea41c681122a5eca5b5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is always a possibility that MSI-X interrupts can get lost. To
keep this problem from stalling the driver, we fire all of our MSI-X
vectors during the watchdog routine. However, we should not fire the
traffic vectors when the interface is closed. In this case, just fire
vector 0, which is used for admin queue events.
As a result, we do not enable the interrupt cause for vector 0. This
can cause the admin queue handler to be called reentrantly, which
causes a scary "critical section violation" message to be logged,
even though no real damage is done.
Change-ID: Ic43a5184708ab2cb9a23fca7dedd808a46717795
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we're using VLANs and communications with the PF fail during
shutdown, we will leak memory because not all of the VLAN filters will
be removed. To eliminate this possibility, go through the list again
right before the module is removed and delete any leftover entries.
Change-ID: Id3b5315c47ca0a61ae123a96ff345d010bc41aed
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF driver is running in the host, the shutdown code is completely
broken. We cannot wait in our down routine for the PF to respond to our
requests, as its admin queue task will never run while we hold the lock.
Instead, we schedule operations, then let the watchdog take care of
shutting things down. If the driver is being removed, then wait in the
remove routine until the watchdog is done before continuing.
Change-ID: I93a58d17389e8d6b58f21e430b56ed7b4590b2c5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These messages may be triggered during normal init of the driver if the
PF or FW take a long time to respond. There's nothing really wrong, so
don't freak people out logging messages.
If the communication channel really is dead, then we'll retry a few
times and give up. This will log a different more scary message that
should cause consternation. This allows the user to more easily detect a
genuine failure.
Change-ID: I6e2b758d4234a3a09c1015c82c8f2442a697cbdb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These functions are redundant and duplicate functionality found in
i40evf_free_all_[tx|rx]_resources.
Change-ID: Ia199908926d7a1a4b8247f75f89b5da24c9b149c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Inline functions are preferred over macros when they can be used
interchangeably.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Decoding the AQ return code is great except when the AQ send timed out
and there's no return code set. This changes the handy decoder
interface to help catch and properly report the condition as a useful
errno rather than returning a misleading '0'.
Change-ID: I07a1f94f921606da49ffac7837bcdc37cd8222eb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't bother trying to set a smaller timeout on the polling,
just simplify the code and always use the max limit. Also,
rename a variable for clarity and fix a comment.
Change-ID: I0300c3562ccc4fd5fa3088f8ae52db0c1eb33af5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The nvm_semaphore_wait field is set but never used, so let's
just get rid of it.
Change-ID: I2107bd29b69f99b1a61d7591d087429527c9d8fa
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just to be sure, add a range check to avoid any possible
array index-out-of-bound issues.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Change-ID: I9323bee6732c2a47599816e1d6c6b3a1f8dcbf54
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM update operations take time finish asynchronously, and follow-on
update requests need to wait for the current one to finish. Early
firmware didn't handle this well, so the code had to track the busy state.
The released firmware handles the busy state correctly, returning
I40E_AQ_RC_EBUSY if an update is still in progress, so the code no longer
needs to track this.
Change-ID: I6e6b4adc26d6dcc5fd7adfee5763423858a7d921
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.
It modifies drivers implementation of set/get_rxfh accordingly.
This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.
User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.
Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple VFs attempt to initialize simultaneously, the firmware may
delay or drop messages. Make the init code more adept at handling these
situations by a) reinitializing the admin queue if the firmware fails to
process a request, and b) resending a request if the PF doesn't answer.
Once the request has been sent again, the PF might end up getting both
requests and send the configuration information to the driver twice.
This will cause the VF to complain about receiving an unexpected message
from the PF. Since this is not fatal, reduce the warning level of the
log messages that are generated in response to this event.
Change-ID: I9370a1a2fde2ad3934fa25ccfd0545edfbbb4805
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is useful for future expansion when new VF MAC types get
added. It helps with cleaning up VF driver flow.
Change-ID: Ibe1eeb71262a3a40f24a1c5409436bdc3411da7f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Virtual Channel OP event opcode for CONFIG_RSS, so that the
Virtual Channel state machine can properly decipher status change events.
Change-ID: I09939c7aa380147f60c49fd01ef2e27d0dc1c299
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This message really doesn't give any useful information and ends up
getting printed every service_task loop in the Linux driver, filling the
logfile with noise when AQ tracing is enabled. This patch simply removes
the noise.
Change-ID: I30ad51e6b03c7ad12a7d9c102def0087db622df3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the if part of this statement contains a break, there's no reason
for the else. Clean up the code and make it more obvious that the delay
happens each time through the loop.
Change-ID: I9292eaf7dd687688bdc401b8bd8d1d14f6944460
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most of the null-checking in this driver is of the style if (!foo),
except these few. Make these checks consistent with the rest of the
code.
Change-ID: I991924f34072fa607a1b626a8b3f1fa5195d43e9
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is the result of running checkpatch on the i40evf driver with
the --strict option. The vast majority of changes are adding/removing
blank lines, aligning function parameters, and correcting over-long
lines.
The only possible functional change is changing the flags member of the
adapter structure to be non-volatile. However, according to the kernel
documentation, this is not necessary and the volatile should be removed.
Change-ID: Ie8c6414800924f529bef831e8845292b970fe2ed
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
No code changes. Update comments to match actual function declarations.
Change-ID: Ib830d2f154ee917a104955c0914267fc98f3d2c8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Overloading the msg_size field in the arq_event_info struct is just a
bad idea. It leads to repeated bugs when the structure is used in a
loop, since the input value (buffer size) is overwritten by the output
value (actual message length).
Fix this by splitting the field into two and renaming to indicate the
actual function of each field.
Since the arq_event struct has now changed, we need to change the drivers
to support this. Note that we no longer need to initialize the buffer size
each time we go through a loop as this value is no longer destroyed by
arq processing.
In the process, we also fix a bug in i40evf_verify_api_ver where the
buffer size was not correctly reinitialized each time through the loop.
Change-ID: Ic7f9633cdd6f871f93e698dfb095e29c696f5581
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's kind of silly to configure and attempt to use a bunch of queue
pairs when you're running on a single (virtual) CPU. Instead of
unconditionally configuring all of the queues that the PF gives us,
clamp the number of queue pairs to the number of CPUs.
Change-ID: I321714c9e15072ee76de8f95ab9a81f86ed347d1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In early init, if we get an unexpected message from the PF (such as link
status), we just kick an error back to the init task, causing it to
restart its state machine and delaying initialization.
Make the early init AQ message receive code more robust by handling
messages in a loop, and ignoring those that we aren't interested in.
This also gets rid of some scary log messages that really didn't
indicate a problem.
Change-ID: I620e8c72e49c49c665ef33eeab2425dd10e721cf
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The interrupt throttle rate minimum is actually 2us, so
fix that define and while we are there, remove some unused defines.
Change some strings in the function to be a bit less wrappy, and
express the correct limits.
Change-ID: I96829bbc77935e0b57c6f0fc1439fb4152b2960a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code was polling the firmware tail register for completion every
10 microseconds, which is way faster than the firmware can respond.
This changes the poll interval to 1ms, which reduces polling CPU
utilization, and the number of times we loop.
The maximum delay is still 100ms.
Change-ID: I4bbfa6b66d802890baf8b4154061e55942b90958
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add 10G-Base-T support in i40evf.
Change-ID: I98a1c3138d7d6572fe7903a7c1c4692cae3260d5
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we receive an admin queue message, the msg_size field in the event
struct gets overwritten. Because of this, we need to reinit the field
each time we go through the loop. Without this we may receive truncated
messages due to the firmware thinking we have insufficient buffer size.
Change-ID: I21dcca5114d91365d731169965ce3ffec0e4a190
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the Documentation/timers/timers-howto.txt it is preferred to use
usleep_range() instead of udelay() if the delay value is > 10us in
non-atomic contexts.
So, replacing all the instances of udelay() with 10 or greater than 10
micro seconds delay in the driver and using usleep_range() instead.
Change-ID: Iaa2ab499a4c26f6005e5d86cc421407ef9de16c7
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is one small step in making the indentation more consistent. If
we truly want to align values, then use tabs rather than spaces.
Change-ID: I12368bc77a52f296d1843fdcb67201a7d7cd4749
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Bump i40e version to 1.0.11 and i40evf version to 1.0.5.
Change-ID: I63a60fa2efe82aae87a8a3095f43218db57d46ce
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Set skb->csum_level instead of skb->encapsulation when indicating
CHECKSUM_UNNECESSARY for an encapsulated checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump versions for i40e to 1.0.4 and i40evf to 1.0.1.
Change-ID: I960c04da2c91bdf1d02f8e5011e68c34a634122d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are seeing situations where the driver sees a hang with less than 4
desc pending, if the driver chooses to ignore it the queue progresses
forward and the stack never experiences a real hang.
With this patch we will log a stat when this situation happens
"tx_sluggish" will increment and we can see some more details
at a higher debug level. Other than that we will ignore this
particular case of Tx hang.
Change-ID: I7d1d1666d990e2b12f4f6bed0d17d22e1b6410d5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is at least one case in the Firmware API where the response to a
command changes the buffer size field in the AQ descriptor to a larger
number than what the request's buffer size started as. This is in addition
to setting an error flag and is in order to tell the requester how much
larger a buffer is required for the answer. We need to be sure not to
use that number when dumping the contents of the data buffer because it
can send us into the weeds and generate an invalid pointer exception.
This patch adds a max buffer size parameter to the print helper to be
sure the code knows when to stop.
Change-ID: Ib84f7ed72140fe9d600086d8f2002fc5d8753092
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
Fix this by using vlan_get_protocol() helper.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Removing VF driver during device still in reset caused guest OS panic.
in the i40evf_remove(), we're trying to clean mac_filter_list which has
not been initialized since the device is still stuck at the reset.
The change is to initialize the filter_list before setting any task.
Change-ID: I8b59df7384416c7e6f2d264b598f447e1c2c92b0
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is loaded and then unloaded before the interface is
brought up, then it will allocate a MAC filter entry and never free it.
To fix this, on unload, run through the mac filter list and free all the
entries. We also do this during reset recovery when the driver cannot
contact the PF and needs to shut down completely.
Change-ID: I15fabd67eb4a1bfc57605a7db60d0b5d819839db
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory leak. Driver was allocating memory for queue vectors on
init but not freeing them on shutdown. These need to be freed at two
different times: during module unload, and during reset recovery when
the driver cannot contact the PF driver and needs to give up.
Change-ID: I7c1d0157a776e960d4da432dfe309035aad7c670
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in an adapter state check to prevent re-arming watchdog timer after
i40evf_remove has been called and timer has been deleted.
Change-ID: I636ba7c6322be8cbf053231959f90c0a2d8d803a
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously defined state I40E_VFR_VFACTIVE uses bit 1 which is now set to
"reserved." Update the state checks to also include I40E_VFR_COMPLETED.
This change will allow the VF to work with both existing and future PFs.
Change-ID: Ifd1d34f79f3b0ffd6d2550ee4dadc55825ff52f8
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was converted to use snprintf everywhere but this one function.
Just use snprintf, instead of sprintf.
Also a small spelling correction in a comment.
Change-ID: I59d45f94a52754c7b4cd6034df9a61d8132b7f77
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes the AQTX answer comes back with no data, but we still want to print
the descriptor that got written back.
Change-ID: I5f734d99b4c95510987413893f0a34626571d474
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Copy desc and buffer data even for ARQ events which return error status.
Previously, a check for NVM related AQ commands which is done later in this
function would not recognize that such a command was received and would
not clear nvm_busy flag. This would block access to NVM until a driver reset.
This will fix that.
Change-ID: If69ad74e165b56081c0686b97402511d2e2880c0
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We really don't need to delay an entire millisecond just to get into our
critical section. A microsecond will be sufficient, thank you.
Change-ID: I2d02ece6610007d98cabcb3f42df9a774bb54e59
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware design requires that the driver avoid indicating
checksum offload success on some ipv6 frames with extension
headers.
The code needs to just check for the IPV6EXADD bit and if
it is set punt the checksum to the stack. I don't know why
the code was checking TCP on inner protocol, as that code
doesn't make any sense to me but seems wrong, so remove it.
Change-ID: I10d3aacdbb1819fb60b4b0eb80e6cc67ef2c9599
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This implements a state machine intended to support the userland tool for
updating the device eeprom. The state machine implements one-shot reads,
writes, multi-step write sessions, and checksum requests. If we're in the middle
of a multi-step write session, no one should fire off other writes, however, one
shot reads are valid. The userland tool is expected to keep track of its session
status, arrange the placement and ordering of the writes, and deal with the
checksum requirement.
This patch also adds nvmupdate support to ethtool callbacks.
The get_eeprom() and set_eeprom() services in ethtool are used here to
facilitate the userland NVMUpdate tool. The 'magic' value in the get and
set commands is used to pass additional control information for managing
the read and write steps.
The read operation works both as normally expected in the standard ethtool
method, as well as with the extra NVM controls. The write operation
works only for the expanded NVM functions - the normal ethtool method is
not allowed because of the NVM semaphore management needed for multipart
writes, as well as the checksum requirement.
Change-ID: I1d84a170153a9f437906744e2e350fd68fe7563d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Remove some break statements that will never get touched.
2. Remove an extra space.
3. Remove a comment for a parameter that doesn't exist
4. Move the assignment of a variable up to get rid of an else case.
Change-ID: I308a4b5ec070b1f0601f13b041ba4375aaad4b06
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump.
Change-ID: Ie0c36583ffd9997679f46bdf89bc462d3e992995
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add function set_fc to set the requested FC mode. This patch also
adds the init of FC setting to get_link_info and replaces the init
code to set FC off by default in main. Also adds i40e_set_phy_config
to support this.
Change-ID: I7b25bbaec81f15777137ab324a095f916e44351d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a new variable, hw.phy.link_info.an_enabled, to track whether autoneg is
enabled. Also add a new function update_link_info that will update that
variable as well as calling get_link_info to update the rest of the link info.
Also add get_phy_capabilities to support this.
Change-ID: I5157ef03492b6dd8ec5e608ba0cf9b0db9c01710
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40evf_irq_enable and i40evf_fire_sw_interrupt functions were
unfairly discriminating against MSI-X vector 0, just because it doesn't
handle traffic. That doesn't mean it's not essential to the operation of
the driver. This change allows the watchdog to fire vector 0 via
software, which makes the driver tolerant of dropped interrupts on that
vector.
Buck up, vector 0! You can be part of our gang!
Change-ID: I37131d955018a6b3e711e1732d21428acd0d767e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Force a shifted '1' to be unsiged to avoid shifting a signed int
Change-ID: I688cbd082af0f2e1df548fda25847a5ca04babcf
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move a declaration up one level so we don't dereference it out of scope.
This didn't cause any panics, but the details->async field would
mysteriously disappear, causing unnecessary delays when sending AQ
commands. Also, the code is just plain wrong.
Change-ID: I753f64f13c55e5d75ea4351e29b14fb53b2f0104
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HW still needs to consume it and freeing it in the function
that created it would mean we will be racing with the HW. The
i40e_clean_tx_ring() routine will free up the buffer attached once
the HW has consumed it. The clean_fdir_tx_irq function had to be fixed
to handle the freeing correctly.
Cases where we program more than one filter per flow (Ipv4), the
code had to be changed to allocate dummy buffer multiple times
since it will be freed by the clean routine. This also fixes an issue
where the filter program routine was not checking if there were
descriptors available for programming a filter.
Change-ID: Idf72028fd873221934e319d021ef65a1e51acaf7
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a slash to the branding string to reduce confusion and match up with
our other marketing materials.
Change-ID: I8229e8c3e43083b7a29c859a250f8d2d4dc46b9e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver needs to initialize all members of context descriptor. Stale
data is possible otherwise.
Change-ID: Idc6b53af45583509da42d5ec0824cbaf78aee64f
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new variable defining ASQ command write back timeout to allow for
dynamic modification of this timeout. Initialize it on AQ initialize
routine with default value, vary it on device ID.
Change-ID: I5c9908f9d7c5455634353b694a986d6f146d1b9d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, the firmware could beat us to the punch, and the
reply from the PF would come back before we were able to properly modify
the aq_pending and aq_required flags. This would mess up the flags and
put the driver in an indeterminate state, much like Schrödinger's cat.
However, unlike the cat, the driver is definitely dead.
To fix this, simply set the flags before sending the request to the AQ.
This way, it won't matter if the interrupt comes back too soon.
Change-ID: I9784655e475675ebcb3140cc7f36f4a96aaadce5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the AQ BAH and BAL registers on a clean shutdown to help make sure
all is tidy when the driver is done.
Change-ID: I393e92680247daa52a8e00bab183213672d73578
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Base Address High and Low to the admin queue struct to simplify
another bit of "which context" logic in the config routines.
Change-ID: Iae195a7da3baffc1a9d522119e1e2b427068ad07
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes the firmware will not indicate an error but fail to pass a
message between the VF and the PF driver. If this happens, just resend
the request.
This fixes an initialization failure if many VFs are instantiated at the
same time and the VF module is autoloaded.
Change-ID: Idd1ad8da2fd5137859244685c355941427d317d7
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct a missing word in a log message.
Change-ID: Id94da7d9f842382d073b3947e0b616503e2f8e91
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When verifying the API version (which is the first time the driver
communicates with the firmware and thus the PF driver), there are many
ways in which a failure can occur. There may be an error from the
firmware, there may be unresponsive firmware, there may be an error from
the PF driver, etc, etc.
Make this function return more useful information, instead of just -EIO.
Propagate FW errors back to the caller, and log a message if the PF
sends an invalid reply.
Change-ID: I3e9135a2b80f7acdb855f62f12b2b2668c9a8951
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF driver fails to complete early init, then rmmod can cause a
softlock when the driver tries to stop a watchdog timer that never even
got initialized.
Add a check to see if the timer is actually initialized before stopping
it.
Change-ID: Id9d550aa8838e07f4b02afe7bc017ef983779efc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix HMC handling for big endian architectures.
Change-ID: Id8c46fc341815d47bfe0af8b819f0ab9a1e9e515
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the PCTYPES that was moved to a reserved value
wasn't removed from the code.
Change-ID: I31fafe6d79c5f5128179979af5eaafa8c0cd62fe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some AQ debug prints needs be moved around or do additional checks so they
will not cause our tool applications to cause segmentation faults.
The tools run in user space and we need to correctly reference kernel
space memory.
Change-ID: Ia2ac4076f576b805f350453fd50ad69c2a91ab9a
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the RSS configuration to set table size
and write to hardware to confirm RSS table size being used.
Change-ID: I455a4c09c9dd479f5791ee1f09fdc83ff9908df5
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The loop in i40evf_get_rxfh_indir was only reading fifteen registers,
not all sixteen. Change the matching loop in i40evf_set_rxfh_indir at
the same time to make the code more consistent.
Change-ID: I6c182287698e742d1f6ca1a4bcc43cc08df6e1de
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reset head and tail on admin queue initialization where H/T are
not reset by HW.
Change-ID: I6db8a2dd3f05ce66410a92cce016191add04760e
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This updates the register file for new hardware.
The format of the file has changed requiring drivers to
declare I40E_MASK. I40E_MASK is to be used with 32 bit registers.
This patch also updates the drivers to accommodate the register changes.
Change-ID: If9bc8d736391024cbf99054efe50f9acc12ee4f1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add members to stat struct to keep track of Flow director ATR and
SideBand filter packet matches.
Change-ID: Ibbb31a53c7adcc2bb96991dd80565442a2f2513c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change drops the FTYPE field from the Rx descriptor, to
match the hardware implementation.
Change-ID: I66d31d2b43861da45e8ace4fb03df033abe88bab
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FW can indicate any admin queue error states to the driver via some bits
in the length registers. Each time we process an admin queue message,
check these bits and log any errors we find. Since the VF really can't
do much, we just print the message and depend on the PF driver to clear
things up on our behalf.
Change-ID: I92bc6c53ce3b4400544e0ca19c5de2d27490bd0d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linux gives us a function to copy Ethernet MAC addresses, let's use it.
Change-ID: I0c861900029ca5ea65a53ca39565852fb633f6fd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the device is down, there's no place to go but up, so don't try to go
down even more. This prevents a CPU soft lock in napi_disable().
Change-ID: I8b058b9ee974dfa01c212fae2597f4f54b333314
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add set_pf_context, replace set_phy_reset with set_phy_debug, add
nvm_config_read/write, remove nvm_read/write_reg_se and add some
PHY types.
With these changes we bump the API version to 1.2.
Change-ID: I4dc3aec175c2316f66fc9b726b3f7d594699d84e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set appropriate fields in Tx queue configuration virtchnl message
to pf to enable headwb and setup headwb addr.
Then use that info from the VF to set headwb and headwb_addr instead of
always enabling them.
Change-ID: I7d393d1b2b07f0f3355b3a4f7c2d3c6ee3b0d622
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bumpity and Fred Worm say it's time to change the numbers again.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Change-ID: I658731d022ea23cedede4be2bfecd8b4cc68d270
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was not marking packets with bad checksums
correctly, especially IPv6 packets with a bad checksum.
To do this correctly we need a define that may be set by
hardware in rare cases.
Change-ID: I1a997b72b491ded27a78ac3bce1197b2d2611130
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix function header comment to have the correct function name.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 0.4.5 and i40evf to 0.9.29.
Change-ID: I9faca5544446518c5425612e733499cf16ef20a1
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove two device IDs 1582 and 1573, because they will not be shipped.
Change-ID: Ica2e550b5b21a69e3f353eba2fe5e1c532a548c4
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a coding error where during the registration for NAPI
the driver requested 256 budget. The max recommended
value for this is NAPI_POLL_WEIGHT or 64.
Change-ID: I03ea1e2934a84ff1b5d572988b18315d6d91c5c6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The TSO logic in the transmit path had some assumptions that
have been broken now that the kernel can send as much as 32kB
in a single skb->frag[.] entry, even on a system with 4kB pages.
This fixes the assumptions and allows the kernel to operate
as efficiently as possible with both SENDFILE and SEND.
In addition, the hardware limit of data contained in a descriptor is
changed to the next power of two below where it currently is in
order to align to a power of two value, preventing a single byte
of data in a descriptor.
Change-ID: I6af1f0b87c1458e10644dbd47541591075a52651
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Both the PF side and the VF side of the VF reset process are too noisy.
We already warn the user that a reset is happening, and that is
sufficient.
Because some of these message are inside if statements, we have to
rejigger the brackets at the same time to keep our coding style
consistent.
Change-ID: Id175562fb0ec7c396d9de156b4890e136f52d5f4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The correct format is %pM, not %pMAC.
Change-ID: Idb335723a966fe56db3a72b9c07c08ca66f9db3c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up inconsistent log messages, mostly related to punctuation. Based
on the dogma that "kernel messages are not sentences", remove all
trailing periods. Reword a few of the messages to make them less
sentence-like.
Change-ID: Ibd849aa7623a77549b0709988c66ab05d1311472
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This comment is just plain false. VF drivers require MSI-X or they won't
get interrupts at all.
Change-ID: Iaea5e30b6926948aa834a3c506d9a9223d9e3e29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to print log messages when we encounter an out-of-memory
condition, as the allocator will do this for us. Also, remove a Tx hang
message that duplicates the one emitted by the netdev layer, and a
duplicate message in the watchdog.
Change-ID: If2056e6135fe248f66ea939778f9895660f4d189
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. There is no ixgbe_watchdog_task function in the driver, so change
the comment to the correct function name, i40e_watchdog_subtask.
2. Remove num_msix_entries from interrupt set_up routine
because it is never used.
3. Remove some TBD comments that are not needed.
Change-ID: I37697a04007074b797f85fd83d626672e4df1ad1
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove use of registers no longer supported.
Change-ID: I9d27399091cea78a926489d94f958edd762f5a20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As reported by Eric Dumazet, the driver is not masking the right
bits in the receive descriptor before it starts checking them.
This patch extends the mask to allow for the right bits to be
checked, and fixes the issue permanently via a define.
CC: Eric Dumazet <eric.dumazet@gmail.com>
Change-ID: I3274f7619057a950f468143e6d7e11b129f54655
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 0.4.3 and i40evf to 0.9.27.
Change-ID: I4141e9f8615bdcfa3b1b5ecbc2ac62603a03b7ad
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a function which indicates our intention to enable or disable a particular
Tx queue. Also add a function to notify the device's Tx unit that we're about
to enable or disable a Tx queue.
Change-ID: I6adf3cbb5bb3e3c984d1ec969e06577c19ef296d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
B0 Si blocks AQ registers when in Blank Flash mode - write is dropped,
read gives 0xDEADBEEF. Introduce a simple check for a correct value in one
of the AQ registers to be sure that AQ was configured correctly.
Without this check we get into an endless loop while trying to send
GetVersion AQ cmd.
Change-ID: I00102b8c5fa6c16d14289be677aafadf87f10f0d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Depending on the timing of what the PF driver is doing, it make take a
few tries before the VF driver is able to communicate with the PF driver
on init or reset recovery. In order to prevent confusion, make the most
common messages less scary by lowering them to a less terrifying log
level and indicate that the driver will retry.
Change-ID: I1ec22aa59a68f4469aabe14775a1bfc1ab4b7f2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rx_errors (GLV_REPC) and rx_missed (GLV_RMPC) were removed
from the chip design.
Change-ID: Ifdeb69c90feac64ec95c36d3d32c75e3a06de3b7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Structure for VEB context added. Update macro for
transition from ms to GTIME (us) time units.
Change-ID: Ib3a19587b4cf355348655df8f60c6f37bb1497a3
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40evf_set_ringparam was broken in several ways. First, it only changed
the size of the first ring, and second, changing the ring size would
often result in a panic because it would change the count before
deallocating resources, causing the driver to either free nonexistent
buffers, or leak leftover buffers.
Fix this by storing the descriptor count in the adapter structure, and
updating the count for each ring each time we allocate them. This
ensures that we always free the right size ring, and always end up with
the requested count when the device is (re)opened.
Change-ID: I298396cd3d452ba8509d9f2d33a93f25868a9a55
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware requires descriptors to be allocated in groups of 32.
Change-ID: I752ccc96769d1bd8d3018c004b8aeff464045bf2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused defines and macros for RX_LRO.
Change-ID: I8ca6715edfa62b56837417a1c4ff68c2345dab6e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ben Hutchings says:
====================
Pull request: Fixes for new ethtool RSS commands
This addresses several problems I previously identified with the new
ETHTOOL_{G,S}RSSH commands:
1. Missing validation of reserved parameters
2. Vague documentation
3. Use of unnamed magic number
4. No consolidation with existing driver operations
I don't currently have access to suitable network hardware, but have
tested these changes with a dummy driver that can support various
combinations of operations and sizes, together with (a) Debian's ethtool
3.13 (b) ethtool 3.14 with the submitted patch to use ETHTOOL_{G,S}RSSH
and minor adjustment for fixes 1 and 3.
v2: Update RSS operations in vmxnet3 too
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The RESETTING state means that a Catastrophic Hardware Bad Thing is
happening and the driver need to tiptoe around and not use the admin
queue or registers or anything like that.
On the other hand, a reinit is no big deal and we can use the admin
queue, and we should. So don't set the state to RESETTING here.
This fixes a Tx hang and FW crash that happens after setting the MTU on
a VF.
Change-ID: I3e6191edbd6a93958a1f1bd1d41a5c2d17474d41
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tx_lpi_status and rx_lpi_status are declared as bool but then used in sizeof
operations in the CORE driver code. Make them u32 to make sparse be quiet.
Change-ID: Iad6daeb1c7149e61ece242acd18c64b320c246a3
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The storm control features are not part of the hardware
and mistakenly were left in the code. Remove them as
they are not needed any more.
Change-ID: I6e9277c8da2c52e69348a657bae25271449c2099
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Patch to remove PCTYPE definitions which are now reserved.
Change-ID: I66c1c16a45a16f4894b2983101ab2a48ce03f1f4
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the i40e_check_asq_alive check to ensure that the len register
offset is non-zero, indicating that SW has initialized the AQ.
Change-ID: I9c2e804788b4775bef9c7e80954ab004e6bdb306
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the is_multicast_ether_addr helper function from linux/etherdevice.h
instead of open coding the multicast address check.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove cases where useless bare return is left at end of function.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For all of our supported kernels, ethtool allows us to directly control
adaptive ITR instead of just faking it with an ITR value. Support this
capability so that user knows explicitly when ITR is being controlled
dynamically. Suggested by Ben Hutchings.
CC: Ben Hutchings <ben@decadent.org.uk>
Change-ID: Iae6b79c5db767a63d22ecd9a9c24acaff02a096e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool consistently reports 0 values for our ITR settings because
we never actually set them. Fix this by setting the default values
to the specified default values.
Change-ID: I2832406a66f7140f2b1230945d6ff6cbf77467c8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Const-ify the ethtool_ops structure, as it is extremely unlikely to
change at runtime. Suggested by Ben Hutchings.
CC: Ben Hutchings <ben@decadent.org.uk>
Change-ID: I1ccb1b7c3ea801cc934447599a35910e7c93d321
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't tell ethtool that the VF can do 10GbaseT, when it really has no
idea what its link speed is. Set the supported values to 0 instead.
Suggested by Ben Hutchings.
CC: Ben Hutchings <ben@decadent.org.uk>
Change-ID: Iceb0d8af68fe5d8dc13224366979ba701ba89c39
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a macro parameter for ethtool stats instead of just assuming
that a valid netdev variable exists. Suggested by Ben Hutchings.
CC: Ben Hutchings <ben@decadent.org.uk>
Change-ID: I66681698573c1549f95fdea310149d8a7e96a60f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding the appropriate GNU General Public License header and
update copyright year to 2014.
Change-ID: I769dd2d37d70350afd0c8727ae2859c0fd340361
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the defines for PCI bus info that are never used.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Minor changes to the AdminQ interface to bring it up-to-date.
Change-ID: Ie31a4cc4911b2d9d3b7f9af2e56fb0ae674f6345
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some information returned via "Get Link Status" command was not
being cached in the struct i40e_link_status.
Add this so the driver can utilize this information as needed.
Change-ID: If084a0ae2a63b16b97572196b993742af2c67772
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the PF driver fails or is removed from the host, the VF driver will
fill up its log with this message.
Change-ID: I67045f987f7c0d444d21ded403adc509343cdb8f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a panic that would occur in the VF if the PF driver failed or was
removed from the host kernel. In this case, the VF driver calls
i40evf_close(), but this function does nothing because the driver is in
the resetting state. Because of this, the driver doesn't free its irqs
and causes a kernel panic when it tries to disable MSI-X.
Change-ID: If95644a89e554b4d7be0dca1b6add26f63047129
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver version string was added to this struct to be passed
down through the firmware to low-level NC-SI functions. We tell
the firmware about the length of the ASCII string not counting
any terminating null.
Change-ID: I09ac98ff9b869e8661c55fc6a5c98808fc280c91
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Anjali Singhai <anjali.singhai@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for getting and setting RSS hashing options, RSS LUT
entries, and getting the number of device channels from ethtool. Because
the LUT is so small for the VFs, we just read and write the device
registers directly instead of maintaining a shadow copy.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to version 0.3.43 and i40evf to version 0.9.21.
Change-ID: Ice4c715731bfa1dfc12dd45418675a3ba6e08d57
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM updates take some time and are asynchronous actions that signal
their completion with an AdminQ event. This code tracks when there is
an NVM update outstanding and won't allow a new update command until a
completion event is received from the current update.
Change-ID: Ic132fe16bd9dc09b002ed38297a877c1a01553ce
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PREFENA field in the receive host memory cache (RX-HMC)
must be visible in order to be set to 1 at driver init for
best performance.
Change-ID: I16b0bcd84cf56f4b6c938201ff5e954bee5a1992
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change broke the RSS LUT programming, causing it to be
programmed with all 0. Correct this by actually assigning the
incremented value back to the counter variable so that the increment
will be remembered by the calling function.
While we're at it, add a proper kernel-doc function comment to our
helper function.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using addressof then casting to the original type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast.cocci
@@
type T;
T foo;
@@
- (T *)&foo
+ &foo
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit 6494294f27 ("i40e/i40evf: Use
dma_set_mask_and_coherent") uses dma_set_mask_and_coherent() to
replace dma_set_coherent_mask() for the benefit of return error.
The conversion brings some confusion in error checking as whether
against DMA_BIT_MASK(64) or DMA_BIT_MASK(32). For one, if error is
zero, the check will be against DMA_BIT_MASK(64) twice. Fix this
error checking by binding the check to the pertinent one.
Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To use for Flow Director specific messages.
Change-ID: I69e39a410aa2661f8fd1ed6af0126fa4c335cb77
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were two spaces between return and the value, we only need one.
Change-ID: Iaa42c33f50d8d149cdf1a4c9c1902295bfd991c4
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx watchdog handler runs in interrupt context, so it would cause an
oops when sending an admin queue message to request a reset, because the
admin queue functions use spinlocks.
Instead, set a flag and let the reset task handle sending the request.
Change-ID: I65879470b72963d9c308edfb8f45ac4fbba2c14f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an error message when the admin queue message never completes, and
fix formatting on another one that was unnecessarily wrapped.
Change-ID: I8b8a4eb7629d741f09357250144023cd4a72231f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver encounters an error while communicating with the PF
driver, don't just shut down the admin queue unconditionally. The PF
may be delayed, and shutting down the admin queue causes it to fail
completely. If this happens, the VF will never complete initialization.
Change-ID: I6192e9d8caeefb738428c3597fa2f54fa400ce7f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump to version 0.3.36 for i40e and 0.9.16 for i40evf.
Change-ID: I7b4ff97b32d2825181803c03c316381a7608a618
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need context descriptors for every packet, only tso
or timesync. This fixes a bug in the driver where it would
always add a context even if all the passed in values
to the context descriptor function were 0/default values.
Change-ID: I0101d2b893380707b5c2de61aab3e16d4310e9a1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a feature to avoid updating the descriptor
ring by marking each descriptor with a DD bit, and instead
writes a memory location with an update to where the driver
should clean up to. Enable this feature.
Change-ID: I5da4e0681f0b581a6401c950a81808792267fe57
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Checkpatch complained in an earlier patch about using min(), but that
change would have been completely unrelated to the point of that patch.
So fix it here.
Change-ID: I2cd87b39cfd406850d283b88f259757a6bcd14cd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HLUT programming loop in in i40evf_configure_rss was a) overly-
complicated, and b) just plain broken. Most of the entries ended up being
not written at all, so most of the flows ended up at queue zero.
Refactor the HLUT programming loop to simply walk through the registers
and write four values to each one, incrementing through the number of
available queues.
Change-ID: I75766179bc67e4e997187794f3144e28c83fd00d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When compiling the i40e and the i40evf driver into the same kernel I get:
LD drivers/net/ethernet/intel/built-in.o
drivers/net/ethernet/intel/i40evf/built-in.o:(.data+0x300): multiple definition of `i40e_ptype_lookup'
drivers/net/ethernet/intel/i40e/built-in.o:(.data+0x780): first defined here
make[3]: *** [drivers/net/ethernet/intel/built-in.o] Error 1
make[2]: *** [drivers/net/ethernet/intel] Error 2
make[1]: *** [drivers/net/ethernet/] Error 2
make: *** [sub-make] Error 2
Fix this by renaming the i40evf version of this structure from
i40e_ptype_lookup to i40evf_ptype_lookup.
This build failure was introduced in:
commit 206812b5fc
Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
i40e/i40evf: i40e implementation for skb_set_hash
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Eric W Biederman <ebiederm@xmission.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Linux 3.13, dma_set_mask_and_coherent was introduced, and we have
been encouraged to use it. It simplifies the DMA mapping code a bit as
well.
Change-ID: I66e340245af7d0dedfa8b40fec1f5e352754432e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that the 2.4 firmware reports the correct number of MSI-X vectors,
use this value correctly when communicating with the VF, and when
setting up the interrupt linked list.
The PF has always reported the correct number of MSI-X vectors, so we
should never increment the value in the vf driver.
Change-ID: Ifeefc631c321390192219ce2af9ada6180c1492f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Fix a name of the error bit to correctly indicate the error.
2) Added a fd_id field in the 32 byte desc at the place(qw0) where it gets
reported in the programming error desc WB. In a normal data desc
the fd_id field is reported in qw3.
Change-ID: Ide9a24bff7273da5889c36635d629bc3b5212010
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to make sure that we stay away from the cache line
where the DD bit (done) may be getting written back for
the transmit ring since the hardware may be writing the
whole cache line for a partial update.
Change-ID: Id0b6dfc01f654def6a2a021af185803be1915d7e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Original comment from Tom Herbert <therbert@google.com>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
This patch builds upon Tom's original implementation and adds
the L4 type return when we know it is an L4 hash.
This requires use of the ptype decoder ring, so enable it.
Change-ID: I2f9fa86d1a6add58cff13386f7f4238b1abcc468
CC: Tom Herbert <therbert@google.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set netdev->hw_features to enable the ndo_set_features netdev op.
Change-Id: I5a086fbfa5a089de5adba2800c4d0b3a73747b11
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix inconsistent use of MSIX and MSI-X in messages.
Change-ID: Iae9ffb42819677c34544719044ed77632e06147d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a bogus space.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bunch of changes merit a new version number, and since these were
made in the new year, update the copyright date.
Change-ID: Ic3f282bf0c20679b9fb06860211afa7c78055bc2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the descriptor ring size in the actual ring structs instead of in
the adapter struct. This enables us to use common tx and rx code with
the i40e PF driver.
Also update copyrights.
Change-ID: I2861e599b2b4c76441c062ea14400f4750f54d0e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to set an interface name here; the net core will do
that, and then it will get renamed by udev anyway.
Change-ID: I839a17837d19bedd1f490bff32ac5b85b4bfd97f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This comment is simply not true.
Change-ID: If006b02b60984601a24257a951ae873dff568008
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure errors are reported at the correct log level, quit printing
the function name every time, and make the messages more consistent in
format.
v2: Removed unnecessary periods and redundant OOM message.
Change-ID: I50e443467519ad3850def131d84626c50612c611
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI DAC doesn't really mean much on a virtualized PCI Express part, so
get rid of that check and just always set the HIGHDMA flag in the net
device.
Change-ID: I2040272be0e7934323f470c2bc73fbdd4f93e2b6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending upon the state of the driver, there are several potential
pitfalls on remove. Kill the watchdog task so rmmod doesn't hang.
Check the adapter->msix_entries field, not the num_msix_vectors field,
which is never cleared.
Change-ID: I0546048477f09fc19e481bd37efa30daae4faa88
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We remove all the MAC filters, so remove the VLAN filters, too.
Change-ID: I4f7559acdf005dc3f359bf6460ce32d183c8878b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the kernel watchdog bites us, ask the PF to reset us and attempt to
reinit the driver.
Change-ID: Ic97665aeeed71ce712b9c4f057e78ff8372522b9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respond better to a VF reset event. When a reset is signaled by the
PF, or detected by the watchdog task, prevent the watchdog from
processing admin queue requests, and schedule the reset task.
In the reset task, wait first for the reset to start, then for it to
complete, then reinit the driver.
If the reset never appears to complete after a long, long time (>10
seconds is possible depending on what's going on with the PF driver),
then set a flag to indicate that PF communications have failed.
If this flag is set, check for the reset to complete in the watchdog,
and attempt to do a full reinitialization of the driver from scratch.
With these changes the VF driver correctly handles a PF reset event
while running on bare metal, or in a VM.
Also update copyrights.
Change-ID: I93513efd0b50523a8345e7f6a33a5e4f8a2a5996
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Dan Carpenter (from Oracle), the flags variable is
declared as a 64-bit long but all of the flags are defined as u32,
which may lead to unintended consequences. Fix this by declaring flags
as u32 (since we don't need any more than about a dozen flags right
now), and remove the volatile qualifier, since it's unnecessary and
just makes checkpatch cry.
Change-ID: I137d3bb1842bf7e9456b5929ca54e3b0ed45dcab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we store the traffic vector names in the queue vector struct, we
don't need to maintain an array of strings for these names in the
adapter structure. Replace this array with a single string and use it
when allocating the misc irq vector.
Also update copyrights.
Change-ID: I664f096c3c008210d6a04a487163e8aa934fee5b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locate the structure in the correct header file.
Change-ID: Ic7853131728812093a44a75d6b70953311a48dab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a bunch of unused structure members that are just wasting
space. Remove a completely unused info structure definition as well.
Also update copyrights.
Change-ID: I028ab92d9b7bd13a832cf3363bd1dc6610d8a535
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change moves one operator up to the previous line and deletes
the duplicate declaration of ETH_ALEN.
Also update copyrights.
Change-ID: I88de73093b584e0f3b29d481ccd83fc4b1a1afa5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a spelling error, s/extention/extension/.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the device ID #defines to follow the _DEV_ID convention
already established in the other Intel drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit 7f12ad741a ("i40evf: transmit
and receive functionality") the s390 builds (allyesconfig) fail with:
drivers/net/ethernet/intel/i40evf/i40e_txrx.c: In function 'i40e_clean_rx_irq':
drivers/net/ethernet/intel/i40evf/i40e_txrx.c:818:3: error: implicit declaration of function 'prefetch'
make[5]: *** [drivers/net/ethernet/intel/i40evf/i40e_txrx.o] Error 1
due to an implicit assumption that the prototype from linux/prefetch.h
will be present.
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A0 stepping silicon specific code
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify the existing Kconfig, Makefile, and MAINTAINERS to add the driver
to the kernel. Add a Makefile and a documentation
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the hardware specific init and management.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the main driver header files, containing structures
and data types specific to the linux driver.
i40e_osdep.h contains some code that helps us adapt our OS agnostic code
to Linux.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This PCI-E SR-IOV virtual function (VF) driver is dependant upon the
physical function (PF) driver (i40e) for nearly all of its hardware
configuration. Requests from the VF driver are passed to the PF using
the hardware's Admin Queue.
This patch contains the functionality for communicating with the PF
driver. Because of the delay inherent in this communications channel,
most of the replies from the PF driver are handled asynchronously. The
exceptions are the "send API version" and "get VF config" messages,
which busy-wait because they are done so early during init that
interrupts are not yet configured.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the ethtool interface and related functionality.
Since the VF driver is mostly unaware of link, much of that
functionality is unused. The driver implements ethtool hooks for
statistics, driver info, and some basic non-link-related driver
settings.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This file contains the transmit, receive, and NAPI functionality.
Some of the functions in this module are extracted from the i40e driver
but functions that are not appropriate for virtual function devices have
been removed.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the driver for the Intel(R) XL710 X710 Virtual Function.
This patch contains the main driver entry points, but does not include
transmit and receive or ethtool functionality, which are presented as
separate patches in this series.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jiri Pirko