The multi-threading facility is introduced with the z13 processor family.
This patch adds code to detect the multi-threading facility. With the
facility enabled each core will surface multiple hardware threads to the
system. Each hardware threads looks like a normal CPU to the operating
system with all its registers and properties.
The SCLP interface reports the SMT topology indirectly via the maximum
thread id. Each reported CPU in the result of a read-scp-information
is a core representing a number of hardware threads.
To reflect the reduced CPU capacity if two hardware threads run on a
single core the MT utilization counter set is used to normalize the
raw cputime obtained by the CPU timer deltas. This scaled cputime is
reported via the taskstats interface. The normal /proc/stat numbers
are based on the raw cputime and are not affected by the normalization.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The call to topology_init is too late for the set_sched_topology call.
The initial scheduling domain structure has already been established
with default topology array. Use the smp_cpus_done() call to get the
s390 specific topology array registered early enough.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull scheduler updates from Ingo Molnar:
"The main scheduling related changes in this cycle were:
- various sched/numa updates, for better performance
- tree wide cleanup of open coded nice levels
- nohz fix related to rq->nr_running use
- cpuidle changes and continued consolidation to improve the
kernel/sched/idle.c high level idle scheduling logic. As part of
this effort I pulled cpuidle driver changes from Rafael as well.
- standardized idle polling amongst architectures
- continued work on preparing better power/energy aware scheduling
- sched/rt updates
- misc fixlets and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (49 commits)
sched/numa: Decay ->wakee_flips instead of zeroing
sched/numa: Update migrate_improves/degrades_locality()
sched/numa: Allow task switch if load imbalance improves
sched/rt: Fix 'struct sched_dl_entity' and dl_task_time() comments, to match the current upstream code
sched: Consolidate open coded implementations of nice level frobbing into nice_to_rlimit() and rlimit_to_nice()
sched: Initialize rq->age_stamp on processor start
sched, nohz: Change rq->nr_running to always use wrappers
sched: Fix the rq->next_balance logic in rebalance_domains() and idle_balance()
sched: Use clamp() and clamp_val() to make sys_nice() more readable
sched: Do not zero sg->cpumask and sg->sgp->power in build_sched_groups()
sched/numa: Fix initialization of sched_domain_topology for NUMA
sched: Call select_idle_sibling() when not affine_sd
sched: Simplify return logic in sched_read_attr()
sched: Simplify return logic in sched_copy_attr()
sched: Fix exec_start/task_hot on migrated tasks
arm64: Remove TIF_POLLING_NRFLAG
metag: Remove TIF_POLLING_NRFLAG
sched/idle: Make cpuidle_idle_call() void
sched/idle: Reflow cpuidle_idle_call()
sched/idle: Delay clearing the polling bit
...
The original bootmem allocator is getting replaced by memblock. To
cover the needs of the s390 kdump implementation the physical memory
list is used.
With this patch the bootmem allocator and its bitmaps are completely
removed from s390.
Signed-off-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The call to update_cpu_masks() from within topology_init()
is completely redundant. This patch removes it.
Signed-off-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Export cpu_topology symbol, so it's available for modules.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Mainly merge all different per-cpu arrays into a single array which
holds all topology information per logical cpu.
Also fix the broken core vs socket variable naming and simplify the
locking a bit.
When running in environments without topology information also
invent book, socket and core ids, so that not all ids are zero.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current topology code confuses core id vs physical package id.
In other words /sys/devices/system/cpu/cpuX/topology/core_id
displays the physical_package_id (aka socket id) instead of the
core id.
The physical_package_id sysfs attribute always displays "-1"
instead of the socket id.
Fix this mix-up with a small patch which defines and initializes
topology_physical_package_id correctly and fixes the broken
core id handling.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use for_each_set_bit() to simplify the code.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cpu polarization member is the only per cpu state that is not part
of the pcpu structure. So add it there and have everything in one place.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The maximum nesting of the cpu topology is evaluated when /proc/sysinfo
is the first time read. This happens without a lock and a concurrent
reader on a different cpu can see and use an invalid intermediate value.
Besides the fact that this race is quite unlikely the worst thing that
could happen is that /proc/sysinfo would contain bogus information about
the machine's cpu topology.
Nevertheless this should be fixed. So move the detection code to the
early machine detection code and since now the value is early available
use it in the topology code as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Any change to sysinfo.h causes a whole kernel recompile since sysinfo.h is
included by topology.h, which again is used nearly everywhere.
So remove that include and add a forward declaration instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Define struct pcpu and merge some of the NR_CPUS arrays into it, including
__cpu_logical_map, current_set and smp_cpu_state. Split smp related
functions to those operating on physical cpus and the functions operating
on a logical cpu number. Make the functions for physical cpus use a
pointer to a struct pcpu. This hides the knowledge about cpu addresses in
smp.c, entry[64].S and swsusp_asm64.S, thus remove the sigp.h header.
The PSW restart mechanism is used to start secondary cpus, calling a
function on an online cpu, calling a function on the ipl cpu, and for
the nmi signal. Replace the different assembler functions with a
single function restart_int_handler. The new entry point calls a function
whose pointer is stored in the lowcore of the target cpu and it can wait
for the source cpu to stop. This covers all existing use cases.
Overall the code is now simpler and there are ~380 lines less code.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (31 commits)
[S390] disassembler: mark exception causing instructions
[S390] Enable exception traces by default
[S390] return address of compat signals
[S390] sysctl: get rid of dead declaration
[S390] dasd: fix fixpoint divide exception in define_extent
[S390] dasd: add sanity check to detect path connection error
[S390] qdio: fix kernel panic for zfcp 31-bit
[S390] Add s390x description to Documentation/kdump/kdump.txt
[S390] Add VMCOREINFO_SYMBOL(high_memory) to vmcoreinfo
[S390] dasd: fix expiration handling for recovery requests
[S390] outstanding interrupts vs. smp_send_stop
[S390] ipc: call generic sys_ipc demultiplexer
[S390] zcrypt: Fix error return codes.
[S390] zcrypt: Rework length parameter checking.
[S390] cleanup trap handling
[S390] Remove Kerntypes leftovers
[S390] topology: increase poll frequency if change is anticipated
[S390] entry[64].S improvements
[S390] make arch/s390 subdirectories depend on config option
[S390] kvm: move cmf host id constant out of lowcore
...
Fix up conflicts in arch/s390/kernel/{smp.c,topology.c} due to the
sysdev removal clashing with "topology: get rid of ifdefs" which moved
some of that code around.
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increase cpu topology change poll frequency if a change is anticipated.
Otherwise a user might be a bit confused to have to wait up to a minute
in order to see a change this should be visible immediatly.
However there is no guarantee that the change will happen during the
time frame the poll frequency is increased.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cleanup z10 topology handling. This adds some more code but hopefully
the result is more readable and easier to maintain.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove all ifdefs from topology code and also only compile it for the
CONFIG_SCHED_BOOK case. The new code selects SCHED_MC if SCHED_BOOK is
selected. SCHED_MC without SCHED_BOOK is not possible anymore.
Furthermore various sysfs attributes are not available anymore for the
!SCHED_BOOK case. In particular all attributes that correspond to
CPU polarization.
But since all real world kernels have SCHED_BOOK selected anyway this
doesn't matter too much.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This moves the 'cpu sysdev_class' over to a regular 'cpu' subsystem
and converts the devices to regular devices. The sysdev drivers are
implemented as subsystem interfaces now.
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Userspace relies on events and generic sysfs subsystem infrastructure
from sysdev devices, which are made available with this conversion.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Len Brown <lenb@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that all cpus in a book on a z10 appear as book siblings
and not as core siblings. This fixes some performance regressions that
appeared after the book scheduling domain got introduced.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix this warning:
WARNING: vmlinux.o(.text+0x199b6): Section mismatch in reference from
the function alloc_masks() to the function .init.text:__alloc_bootmem()
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Merge irq.c and s390_ext.c into irq.c. That way all external interrupt
related functions are together.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix cpu masks for 'topology=off' case. Folding of the scheduling domains
happen in such a way that everything belongs to the MC domain instead
of the CPU doimain.
This should fix a performance regression introduced with
eafd2b6d "[S390] topology: use default MC domain initializer" and also
makes sure we have the same behavious as if CONFIG_SCHED_MC was not
selected at all.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Export the cpu configuration topology via sysinfo. Two new lines are
introduced:
CPU Topology HW: 0 0 0 4 6 4
CPU Topology SW: 0 0 0 0 4 24
The HW line describes the cpu topology nesting levels when the maximum
nesting level is used to get the corresponding SYSIB.
The SW line describes what Linux is actually using. In this case it
supports only two levels (CONFIG_SCHED_BOOK off) and therefore the
hardware folded the two lower levels in the SYSIB response block.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the topology sysinfo SYSIB definitions to the proper place in
asm/sysinfo.h where they should be.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move cpu topology facility detection to early setup code where it
should be.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Store the facility list once at system startup with stfl/stfle and
reuse the result for all facility tests.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Switch default value of the kernel parameter 'topology' from off to on.
Various performance measurements have finally shown that there are no
(known) regressions anywhere.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the extended cpu topology information that z11 machines provide
to improve the scheduler's decision making.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20100831082844.604956770@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Provide a topology_core_id define which makes sure that the contents of
/sys/devices/system/cpu/cpuX/topology/core_id
indeed do contain the core id and not always 0.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the default case the lock is not unlocked. The return is
converted to a goto, to share the unlock at the end of the function.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E1;
identifier f;
@@
f (...) { <+...
* spin_lock_irq (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Finally move it to the place where it belongs to and make get rid of
it for !CONFIG_SMP.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Impact: cleanup
cpu_coregroup_mask is the New Hotness.
As S/390 uses theirs internally, so we just make it static.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Like cpu_coregroup_map, but returns a (const) pointer.
Compile-tested on s390 (defconfig).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Interrupts haven't been implemented. So remove the dead code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce a topology=[on|off] kernel parameter which allows to switch
cpu topology on/off. Default will be off, since it looks like that for
some workloards this doesn't behave very well (on s390).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Call rebuild_sched_domains instead of arch_reinit_sched_domains if
cpu topology changes. This leaves cpu sets alone which otherwise would
be destroyed.
If and how it makes sense to define cpu sets on a virtualized
architecture is another question.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Common code doesn't call arch_update_cpu_topology() anymore on
cpu hotplug. But our architecture backend relied on that in order to
update the cpu_core_map. For machines without cpu topology support
this leads uninitialized cpu_core_maps for later on added cpus.
To solve this just initialize the maps with cpu_possible_map, since
that will be always valid for machines without topology support.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change arch_update_cpu_topology so it returns 1 if the cpu topology changed
and 0 if it didn't change. This will be useful for the next patch which adds
a call to this function in partition_sched_domains.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
cpu_coregroup_map used to grab a mutex on s390 since it was only
called from process context.
Since c7c22e4d5c "block: add support
for IO CPU affinity" this is not true anymore.
It now also gets called from softirq context.
To prevent possible deadlocks change this in architecture code and
use a spinlock instead of a mutex.
Cc: stable@kernel.org
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Now that it is safe to use get_online_cpus() we can revert
[S390] cpu topology: Fix possible deadlock.
commit: fd781fa25c
and call arch_reinit_sched_domains() directly from topology_work_fn().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: Paul Menage <menage@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As noted by Akinobu Mita in patch b1fceac2b9,
alloc_bootmem and related functions never return NULL and always return a
zeroed region of memory. Thus a NULL test or memset after calls to these
functions is unnecessary.
arch/s390/kernel/topology.c | 2 --
1 file changed, 2 deletions(-)
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
statement S;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
- memset(E,0,E1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When we get a notification that cpu topology changed, we schedule a
work struct which just calls arch_reinit_sched_domains. This function
in turn calls get_online_cpus() which results int the lockdep warning
below.
After all it turnded out that it's not legal to call get_online_cpus()
from the context of a multi-threaded work queue.
It could deadlock this way:
process 0 (events/cpu-x):
-> run_workqueue
-> removes my work_struct from the work queue
-> calls work_struct->fn
-> get_online_cpus()
-> locks on cpu_hotplug.lock since process 1 below is doing cpu hotplug
process 1:
-> cpu_down (for cpu-x)
-> cpu_hotplug_begin (holds cpu_hotplug.lock now)
-> cpu-x dead
-> notifier_call_chain with CPU_DEAD
-> cleanup_workqueue_thread
-> flush_cpu_workqueue (succeeds)
-> kthread_stop for events/cpu-x
-> now kthread_stop waits for my work_struct to complete from within
process 0. -> dead.
A single threaded workqueue wouldn't have such problems, however there is
no such common queue available and it's not worth to create one for the
very rare calls to arch_reinit_sched_domains.
So we just create a kernel thread from our work struct which calls
arch_reinit_sched_domains and are done with it.
Thanks to Oleg Nesterov and Peter Zijlstra for helping me figuring out
that this isn't a false positive lockdep warning:
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.25-03562-g3dc5063-dirty #12
-------------------------------------------------------
events/3/14 is trying to acquire lock:
(&cpu_hotplug.lock){--..}, at: [<0000000000076094>] get_online_cpus+0x50/0x78
but task is already holding lock:
(topology_work){--..}, at: [<0000000000059cde>] run_workqueue+0x106/0x278
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (topology_work){--..}:
[<000000000006fc74>] __lock_acquire+0x1010/0x111c
[<000000000006fe40>] lock_acquire+0xc0/0xf8
[<0000000000059d48>] run_workqueue+0x170/0x278
[<0000000000059edc>] worker_thread+0x8c/0xf0
[<000000000005f5bc>] kthread+0x68/0xa0
[<000000000001a33e>] kernel_thread_starter+0x6/0xc
[<000000000001a338>] kernel_thread_starter+0x0/0xc
-> #1 (events){--..}:
[<000000000006fc74>] __lock_acquire+0x1010/0x111c
[<000000000006fe40>] lock_acquire+0xc0/0xf8
[<000000000005a23c>] cleanup_workqueue_thread+0x60/0xa8
[<00000000003b2ab8>] workqueue_cpu_callback+0xbc/0x170
[<00000000003bba80>] notifier_call_chain+0x5c/0xa4
[<00000000000655a2>] __raw_notifier_call_chain+0x26/0x38
[<00000000000655e2>] raw_notifier_call_chain+0x2e/0x40
[<0000000000075e00>] cpu_down+0x228/0x31c
[<00000000003b1dd8>] store_online+0x64/0xb8
[<00000000001e7128>] sysdev_store+0x48/0x58
[<0000000000121cd2>] sysfs_write_file+0x126/0x1c0
[<00000000000c1944>] vfs_write+0xb0/0x15c
[<00000000000c20e6>] sys_write+0x56/0x88
[<0000000000027a68>] sys32_write+0x34/0x4c
[<0000000000023f70>] sysc_noemu+0x10/0x16
[<0000000077f3f186>] 0x77f3f186
-> #0 (&cpu_hotplug.lock){--..}:
[<000000000006fa84>] __lock_acquire+0xe20/0x111c
[<000000000006fe40>] lock_acquire+0xc0/0xf8
[<00000000003b701c>] mutex_lock_nested+0xd0/0x364
[<0000000000076094>] get_online_cpus+0x50/0x78
[<000000000003a03e>] arch_reinit_sched_domains+0x26/0x58
[<000000000002700e>] topology_work_fn+0x26/0x34
[<0000000000059d4e>] run_workqueue+0x176/0x278
[<0000000000059edc>] worker_thread+0x8c/0xf0
[<000000000005f5bc>] kthread+0x68/0xa0
[<000000000001a33e>] kernel_thread_starter+0x6/0xc
[<000000000001a338>] kernel_thread_starter+0x0/0xc
other info that might help us debug this:
2 locks held by events/3/14:
#0: (events){--..}, at: [<0000000000059cde>] run_workqueue+0x106/0x278
#1: (topology_work){--..}, at: [<0000000000059cde>] run_workqueue+0x106/0x278
stack backtrace:
CPU: 3 Not tainted 2.6.25-03562-g3dc5063-dirty #12
Process events/3 (pid: 14, task: 000000002fb04038, ksp: 000000002fb0bd70)
0400000000000000 000000002fb0ba40 0000000000000002 0000000000000000
000000002fb0bae0 000000002fb0ba58 000000002fb0ba58 0000000000016488
0000000000000000 000000002fb0bd70 0000000000000000 0000000000000000
000000002fb0ba40 000000000000000c 000000002fb0ba40 000000002fb0bab0
00000000003c99e0 0000000000016488 000000002fb0ba40 000000002fb0ba90
Call Trace:
([<00000000000163fc>] show_trace+0x138/0x158)
[<00000000000164e2>] show_stack+0xc6/0xf8
[<0000000000016624>] dump_stack+0xb0/0xc0
[<000000000006cd36>] print_circular_bug_tail+0xa2/0xb4
[<000000000006fa84>] __lock_acquire+0xe20/0x111c
[<000000000006fe40>] lock_acquire+0xc0/0xf8
[<00000000003b701c>] mutex_lock_nested+0xd0/0x364
[<0000000000076094>] get_online_cpus+0x50/0x78
[<000000000003a03e>] arch_reinit_sched_domains+0x26/0x58
[<000000000002700e>] topology_work_fn+0x26/0x34
[<0000000000059d4e>] run_workqueue+0x176/0x278
[<0000000000059edc>] worker_thread+0x8c/0xf0
[<000000000005f5bc>] kthread+0x68/0xa0
[<000000000001a33e>] kernel_thread_starter+0x6/0xc
[<000000000001a338>] kernel_thread_starter+0x0/0xc
INFO: lockdep is turned off.
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Martin Schwidefsky