[ Upstream commit 027cca9eb5 ]
The mdss node sets #interrupt-cells = <1>, so its interrupts
should be referenced using a single cell (in this case: only the
interrupt number).
However, right now the mdp/dsi node both have two interrupt cells
set, e.g. interrupts = <4 0>. The 0 is probably meant to say
IRQ_TYPE_NONE (= 0), but with #interrupt-cells = <1> this is
actually interpreted as a second interrupt line.
Remove the IRQ flags from both interrupts to fix this.
Fixes: 305410ffd1 ("arm64: dts: msm8916: Add display support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2f0cbb57d ]
Tha parent node of "wcd_codec" specifies #address-cells = <1>
and #size-cells = <0>, which means that each resource should be
described by one cell for the address and size omitted.
However, wcd_codec currently lists 0x200 as second cell (probably
the size of the resource). When parsing this would be treated like
another memory resource - which is entirely wrong.
To quote the device tree specification [1]:
"If the parent node specifies a value of 0 for #size-cells,
the length field in the value of reg shall be omitted."
[1]: https://www.devicetree.org/specifications/
Fixes: 5582fcb382 ("arm64: dts: apq8016-sbc: add analog audio support with multicodec")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6859ae860 ]
Commit fe2aff0c57 ("arm64: dts: qcom: msm8916: remove unit name for thermal trip points")
removed the unit names for most of the thermal trip points defined
in msm8916.dtsi, but missed to update the one for cpu0_1-thermal.
So why wasn't this spotted by "make dtbs_check"? Apparently, the name
of the thermal zone is already invalid: thermal-zones.yaml specifies
a regex of ^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$, so it is not allowed
to contain underscores. Therefore the thermal zone was never verified
using the DTB schema.
After replacing the underscore in the thermal zone name, the warning
shows up:
apq8016-sbc.dt.yaml: thermal-zones: cpu0-1-thermal:trips: 'trip-point@0'
does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Fix up the thermal zone names and remove the unit name for the trip point.
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Fixes: fe2aff0c57 ("arm64: dts: qcom: msm8916: remove unit name for thermal trip points")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2ee9edc28 ]
The original qcom kernel changed the PDM GPIOs to be pull-down
during sleep at some point. Reportedly this was done because
there was some "leakage at PDM outputs during sleep":
https://source.codeaurora.org/quic/la/kernel/msm-3.10/commit/?id=0f87e08c1cd3e6484a6f7fb3e74e37340bdcdee0
I cannot say how effective this is, but everything seems to work
fine with this change so let's apply the same to mainline just
to be sure.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200605185916.318494-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b6a1a162d ]
msm8916-pins.dtsi specifies "bias-pull-none" for most of the audio
pin configurations. This was likely copied from the qcom kernel fork
where the same property was used for these audio pins.
However, "bias-pull-none" actually does not exist at all - not in
mainline and not in downstream. I can only guess that the original
intention was to configure "no pull", i.e. bias-disable.
Change it to that instead.
Fixes: 143bb9ad85 ("arm64: dts: qcom: add audio pinctrls")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200605185916.318494-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61d2ca503d ]
This was mistakenly copied from the downstream dts, however the upstream
driver works differently.
I only tested this with the pm8150_gpios node (used with volume button),
but the 2 others should be the same.
Fixes: e92b61c8e7 ("arm64: dts: qcom: pm8150l: Add base dts file")
Fixes: 229d5bcad0 ("arm64: dts: qcom: pm8150b: Add base dts file")
Fixes: 5101f22a5c ("arm64: dts: qcom: pm8150: Add base dts file")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200420153543.14512-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe2aff0c57 ]
The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/2d3d045c18a2fb85b28cf304aa11ae6e6538d75e.1585562459.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e198c395a ]
The WiFi firmware used on db845c implements the 8bit host-capability
message, so enable the quirk for this.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20191113232245.4039932-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d026c96b25 ]
QUSB2 PHY on msm8996 doesn't work well when autosuspend by
dwc3 core using USB2PHYCFG register is enabled. One of the
issue seen is that PHY driver reports PLL lock failure and
fails phy_init() if dwc3 core has USB2 PHY suspend enabled.
Fix this by using quirks to disable USB2 PHY LPM/suspend and
dwc3 core already takes care of explicitly suspending PHY
during suspend if quirks are specified.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Link: https://lore.kernel.org/r/20191209151501.26993-1-p.pisati@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 05caa5bf9c upstream.
The tcsr syscon region is really 0x40000 in size. We need access to the
full region so that we can access the axi resets when managing the
modem subsystem.
Fixes: c783394956 ("arm64: dts: qcom: msm8998: Add smem related nodes")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20191107045948.4341-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eac8ce86cb upstream.
vdd_apc is the regulator that supplies the main CPU cluster.
At sudden CPU load changes, we have noticed invalid page faults on
addresses with all bits shifted, as well as on addresses with individual
bits flipped.
By putting the vdd_apc regulator in high power mode, the voltage drops
during sudden load changes will be less severe, and we have not been able
to reproduce the invalid page faults with the regulator in this mode.
Fixes: 8faea8edbb ("arm64: dts: qcom: qcs404-evb: add spmi regulators")
Cc: stable@vger.kernel.org
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191014120920.12691-1-niklas.cassel@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43b0a4b482 upstream.
This is unused on cheza. Delete the node to get ride of the reserved-
memory section, and to avoid the driver from attempting to load a zap
shader that doesn't exist every time it powers up the GPU.
This also avoids a massive amount of dmesg spam about missing zap fw:
msm ae00000.mdss: [drm:adreno_request_fw] *ERROR* failed to load
qcom/a630_zap.mdt: -2
adreno 5000000.gpu: [drm:adreno_zap_shader_load] *ERROR* Unable to
load a630_zap.mdt
Signed-off-by: Rob Clark <robdclark@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 3fdeaee951 ("arm64: dts: sdm845: Add zap shader region for GPU")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a636f93fcd upstream.
Boot failure has been reported on MSM8998 based laptop when
coresight is enabled. This is most likely due to lack of
firmware support for coresight on production device when
compared to debug device like MTP where this issue is not
observed. So disable coresight by default for MSM8998 and
enable it only for MSM8998 MTP.
Reported-and-tested-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Fixes: 783abfa224 ("arm64: dts: qcom: msm8998: Add Coresight support")
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e38161bd32 upstream.
In the same way as for msm8974-hammerhead, l21 load, used for SDCARD
VMMC, needs to be increased in order to prevent any voltage drop issues
(due to limited current) happening with some SDCARDS or during specific
operations (e.g. write).
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 660a9763c6 (arm64: dts: qcom: db820c: Add pm8994 regulator node)
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b40dd23f9a upstream.
The retention idle state does not appear to be supported by the firmware
present on the msm8998 laptops since the state is advertised as disabled
in ACPI, and attempting to enable the state in DT is observed to result
in boot hangs. Therefore, remove the state from use to address the
observed issues.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Fixes: 2c6d2d3a58 (arm64: dts: qcom: Add Lenovo Miix 630)
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates.
The only core change this time around is the addition of request
batching for virtio. Since batching requires an additional flag to
use, it should be invisible to the rest of the drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXYQE/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXs9AP4usPY5
OpMlF6OiKFNeJrCdhCScVghf9uHbc7UA6cP+EgD/bCtRgcDe1ZjOTYWdeTwvwWqA
ltWYonnv6Lg3b1f9yqI=
=jRC/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
only core change this time around is the addition of request batching
for virtio. Since batching requires an additional flag to use, it
should be invisible to the rest of the drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
scsi: hisi_sas: Fix the conflict between device gone and host reset
scsi: hisi_sas: Add BIST support for phy loopback
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
scsi: hisi_sas: Remove some unused function arguments
scsi: hisi_sas: Remove redundant work declaration
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
scsi: hisi_sas: Update all the registers after suspend and resume
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
scsi: virtio_scsi: unplug LUNs when events missed
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
...
Specify the UFS device-reset gpio for db845c and mtp, so that the
controller will issue a reset of the UFS device.
Link: https://lore.kernel.org/r/20190828191756.24312-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The Lenovo Yoga C630 is built on the SDM850 from Qualcomm, but this seem
to be similar enough to the SDM845 that we can reuse the sdm845.dtsi.
Supported by this patch is: keyboard, battery monitoring, UFS storage,
USB host and Bluetooth.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
[Lee] Reorder, change licence, remove non-upstream device node
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
RPM clock controller has parent as xo, so specify that in DT node for
rpmhcc
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the regulators found in the mtp platform. This platform consists of
pmic PM8150, PM8150L and PM8009.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This add base DTS file for sm8150-mtp and enables boot to console, adds
tlmm reserved range, resin node, volume down key and also includes pmic
file.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PMIC pm8150l is a slave pmic and this adds base DTS file for pm8150l
with power-on, adc and gpio nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PMIC pm8150b is a slave pmic and this adds base DTS file for pm8150b
with power-on, adc, and gpio nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add base DTS file for pm8150 along with GPIOs, power-on, rtc and vadc
nodes
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This add base DTS file with cpu, psci, firmware, clock node tlmm and
spmi and enables boot to console
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add fastrpc compute context bank nodes to both cdsp and adsp.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add dynamic power coefficients for the Silver and Gold CPU cores of
the Qualcomm SDM845.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Update the reserved-memory map to version 3, to adjust to changes in the
remoteprocs.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
'7d0c76bdf227 ("clk: qcom: Add WCSS gcc clock control for QCS404")'
introduces two new clocks to gcc. These are not used before
clk_disable_unused() and as such the clock framework tries to disable
them.
But on the EVB these registers are only accessible through TrustZone, so
these clocks must be marked as "protected" to prevent the clock code
from touching them.
Numerical values are used as the constants are not yet available in a
common tree.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Longcheer L8150 is a smartphone based on MSM8916 which is
used in several rebrands like the Snapdragon 410
Android One devices or the Wileyfox Swift.
Add a device tree for L8150 with initial support for:
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- Regulators
Co-developed-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Samsung Galaxy A3 (SM-A300FU) and Samsung Galaxy A5 (SM-A500FU)
are smartphones using the MSM8916 SoC released in 2015.
Add a device tree for A3U and A5U with initial support for:
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5502 MUIC)
- Regulators
The two devices (and all other variants of A3/A5 released in 2015)
are very similar, with some differences in display, touchscreen
and sensors. The common parts are shared in
msm8916-samsung-a2015-common.dtsi to reduce duplication.
The device tree is loosely based on apq8016-sbc.dtsi and the
downstream kernel provided by Samsung, mixed with a lot of own
research.
Co-developed-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds Qualcomm Venus video codec DT node for the video
codec hardware found in MSM8996 platforms.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
AOSS hosts resources that can be used to warm up the SoC.
Add nodes for these resources.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable coresight support by adding device nodes for the
available source, sinks and channel blocks on msm8996.
This also adds coresight cpu debug nodes.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable coresight support by adding device nodes for the
available source, sinks and channel blocks on MSM8998.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DT nodes should be ordered by address, then node name, and finally label.
The msm8998 dtsi does not follow this, so clean it up by reordering the
nodes. While we are at it, extend the addresses to be fully 32-bits wide
so that ordering is easy to determine when adding new nodes. Also, two
or so nodes had the wrong address value in their node name (did not match
the reg property), so fix those up as well.
Hopefully going forward, things can be maintained so that a cleanup like
this is not needed.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The thermal trip points have unit name but no reg property, so we can
remove them
arch/arm64/boot/dts/qcom/qcs404.dtsi:1080.31-1084.7: Warning (unit_address_vs_reg): /thermal-zones/aoss-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1095.33-1099.7: Warning (unit_address_vs_reg): /thermal-zones/q6-hvx-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1110.32-1114.7: Warning (unit_address_vs_reg): /thermal-zones/lpass-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1125.31-1129.7: Warning (unit_address_vs_reg): /thermal-zones/wlan-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1140.34-1144.7: Warning (unit_address_vs_reg): /thermal-zones/cluster-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1145.34-1149.7: Warning (unit_address_vs_reg): /thermal-zones/cluster-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1174.31-1178.7: Warning (unit_address_vs_reg): /thermal-zones/cpu0-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1179.31-1183.7: Warning (unit_address_vs_reg): /thermal-zones/cpu0-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1208.31-1212.7: Warning (unit_address_vs_reg): /thermal-zones/cpu1-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1213.31-1217.7: Warning (unit_address_vs_reg): /thermal-zones/cpu1-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1242.31-1246.7: Warning (unit_address_vs_reg): /thermal-zones/cpu2-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1247.31-1251.7: Warning (unit_address_vs_reg): /thermal-zones/cpu2-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1276.31-1280.7: Warning (unit_address_vs_reg): /thermal-zones/cpu3-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1281.31-1285.7: Warning (unit_address_vs_reg): /thermal-zones/cpu3-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/qcs404.dtsi:1310.30-1314.7: Warning (unit_address_vs_reg): /thermal-zones/gpu-thermal/trips/trip-point@0: node has a unit name, but no reg property
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
pms405@1 nodes specified unnecessary #address-cells/#size-cells but the
subnodes dont have "ranges" or "reg" so remove it
arch/arm64/boot/dts/qcom/pms405.dtsi:141.21-150.4: Warning (avoid_unnecessary_addr_size): /soc@0/spmi@200f000/pms405@1: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The adc nodes have reg property but were missing the unit name, so add
that to fix these warnings:
arch/arm64/boot/dts/qcom/pms405.dtsi:91.12-94.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/ref_gnd: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:96.14-99.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/vref_1p25: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:101.19-104.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/vph_pwr: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:106.13-109.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/die_temp: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:111.27-116.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/thermistor1: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:118.27-123.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/thermistor3: node has a reg or ranges property, but no unit name
arch/arm64/boot/dts/qcom/pms405.dtsi:125.22-130.6: Warning (unit_address_vs_reg): /soc@0/spmi@200f000/pms405@0/adc@3100/xo_temp: node has a reg or ranges property, but no unit name
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Last level cache (aka. system cache) controller provides control
over the last level cache present on SDM845. This cache lies after
the memory noc, right before the DDR.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Node names shouldn't include a vendor prefix and should whenever
possible use a generic identifier. Resolve this by renaming the smmu
nodes "iommu".
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Unit name is supposed to be a number, using a macro with hex value is
not recommended, so add the value in unit name.
arch/arm64/boot/dts/qcom/pm8998.dtsi:81.18-84.6: Warning (unit_address_format): /soc/spmi@c440000/pmic@0/adc@3100/adc-chan@0x06: unit name should not have leading "0x"
arch/arm64/boot/dts/qcom/pm8998.dtsi:81.18-84.6: Warning (unit_address_format): /soc/spmi@c440000/pmic@0/adc@3100/adc-chan@0x06: unit name should not have leading 0s
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Unit address is supposed to be a number, using a macro with hex value is
not recommended, so add the value in unit name.
arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi:966.16-969.4: Warning (unit_address_format): /soc@0/spmi@c440000/pmic@0/adc@3100/adc-chan@0x4d: unit name should not have leading "0x"
arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi:971.16-974.4: Warning (unit_address_format): /soc@0/spmi@c440000/pmic@0/adc@3100/adc-chan@0x4e: unit name should not have leading "0x"
arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi:976.16-979.4: Warning (unit_address_format): /soc@0/spmi@c440000/pmic@0/adc@3100/adc-chan@0x4f: unit name should not have leading "0x"
arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi:981.16-984.4: Warning (unit_address_format): /soc@0/spmi@c440000/pmic@0/adc@3100/adc-chan@0x50: unit name should not have leading "0x"
arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi:986.16-989.4: Warning (unit_address_format): /soc@0/spmi@c440000/pmic@0/adc@3100/adc-chan@0x51: unit name should not have leading "0x"
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The thermal trip points have unit name but no reg property, so we can
remove them
arch/arm64/boot/dts/qcom/sdm845.dtsi:2824.31-2828.7: Warning (unit_address_vs_reg): /thermal-zones/cpu0-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:2830.31-2834.7: Warning (unit_address_vs_reg): /thermal-zones/cpu0-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:2868.31-2872.7: Warning (unit_address_vs_reg): /thermal-zones/cpu1-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:2874.31-2878.7: Warning (unit_address_vs_reg): /thermal-zones/cpu1-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:2912.31-2916.7: Warning (unit_address_vs_reg): /thermal-zones/cpu2-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:2918.31-2922.7: Warning (unit_address_vs_reg): /thermal-zones/cpu2-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:2956.31-2960.7: Warning (unit_address_vs_reg): /thermal-zones/cpu3-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:2962.31-2966.7: Warning (unit_address_vs_reg): /thermal-zones/cpu3-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3000.31-3004.7: Warning (unit_address_vs_reg): /thermal-zones/cpu4-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3006.31-3010.7: Warning (unit_address_vs_reg): /thermal-zones/cpu4-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3044.31-3048.7: Warning (unit_address_vs_reg): /thermal-zones/cpu5-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3050.31-3054.7: Warning (unit_address_vs_reg): /thermal-zones/cpu5-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3088.31-3092.7: Warning (unit_address_vs_reg): /thermal-zones/cpu6-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3094.31-3098.7: Warning (unit_address_vs_reg): /thermal-zones/cpu6-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3132.31-3136.7: Warning (unit_address_vs_reg): /thermal-zones/cpu7-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3138.31-3142.7: Warning (unit_address_vs_reg): /thermal-zones/cpu7-thermal/trips/trip-point@1: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3176.32-3180.7: Warning (unit_address_vs_reg): /thermal-zones/aoss0-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3191.35-3195.7: Warning (unit_address_vs_reg): /thermal-zones/cluster0-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3211.35-3215.7: Warning (unit_address_vs_reg): /thermal-zones/cluster1-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3231.31-3235.7: Warning (unit_address_vs_reg): /thermal-zones/gpu-thermal-top/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3246.31-3250.7: Warning (unit_address_vs_reg): /thermal-zones/gpu-thermal-bottom/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3261.32-3265.7: Warning (unit_address_vs_reg): /thermal-zones/aoss1-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3276.35-3280.7: Warning (unit_address_vs_reg): /thermal-zones/q6-modem-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3291.30-3295.7: Warning (unit_address_vs_reg): /thermal-zones/mem-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3306.31-3310.7: Warning (unit_address_vs_reg): /thermal-zones/wlan-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3321.33-3325.7: Warning (unit_address_vs_reg): /thermal-zones/q6-hvx-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3336.33-3340.7: Warning (unit_address_vs_reg): /thermal-zones/camera-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3351.32-3355.7: Warning (unit_address_vs_reg): /thermal-zones/video-thermal/trips/trip-point@0: node has a unit name, but no reg property
arch/arm64/boot/dts/qcom/sdm845.dtsi:3366.32-3370.7: Warning (unit_address_vs_reg): /thermal-zones/modem-thermal/trips/trip-point@0: node has a unit name, but no reg property
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Stephan Gerhold