Adding relevant read out comparison code, in check_crtc_state, for the new
member of crtc_config, dp_m2_n2, which was introduced to store link_m_n
values for a DP downclock mode (if available). Suggested by Daniel.
v2: Changed patch title.
Daniel's review comments incorporated.
Added relevant state readout code for M2_N2. dp_m2_n2 comparison to be done
only when high RR is not in use (This is because alternate m_n register
programming will be done only when low RR is being used).
v3: Modified call to get_m2_n2 which had dp_m_n as param by mistake.
Compare dp_m_n and dp_m2_n2 for gen 7 and below. compare the structures
based on DRRS state for gen 8 and above.
Save and restore M2 N2 registers for gen 7 and below
v4: For Gen>=8, check M_N registers against dp_m_n and dp_m2_n2 as there is
only one set of M_N registers
v5: Removed the chunk which saves and restores M2_N2 registers. Modified
get_m_n() to get M2_N2 registers as well. Modified the macro which compares
hw.dp_m_n against sw.dp_m2_n2/sw.dp_m_n for gen > 8.
v6: Added check to compare dp_m2_n2 only when DRRS is enabled
v7: Modified drrs check to use has_drrs
v8: Add has_drrs check before reading M2_N2 registers
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Gen < 8, set M2_N2 registers on every mode set. This is required to make
sure M2_N2 registers are set during boot, resume from sleep for cross-
checking the state. The register is set only if DRRS is supported.
v2: Patch rebased
v3: Daniel's review comments
- Removed HAS_DRRS(dev) and added bool has_drrs to pipe_config to
track drrs support
v4: Jesse's review comments
- Made changes to set m2_n2 in intel_dp_set_m_n()
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 521e62e49a.
Although POST_SYNC brought a bit of stability to Semaphores on BDW
it didn't solved all issues and some hungs can still occour when
semaphores are enabled on BDW. Also some sloweness can be found on some
igt tests, althoguth it apparently doesn't affect real workloads.
Besides that, no real performance gain was found on our tests with different
and even multiple workloads.
Let's disable it again for now. At least until we are sure it is safe
to re-enable it.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Withtout this, ring initialization fails reliabily during resume with
[drm:init_ring_common] *ERROR* render ring initialization failed ctl 0001f001 head ffffff8804 tail 00000000 start 000e4000
This is not a complete fix, but it is verified to make the ring
initialization failures during resume much less likely.
We were not able to root-cause this bug (likely HW-specific to Gen4 chips)
yet. This is therefore used as a ducttape before problem is fully
understood and proper fix created, so that people don't suffer from
completely unusable systems in the meantime.
The discussion and debugging is happening at
https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This particular nasty presented itself while trying to register the
intelfb device (intel_fbdev.c). During the process of registering the device
the driver will disable the crtc via i9xx_crtc_disable. These will
also disable the panel using the generic mipi panel functions in
dsi_mod_vbt_generic.c. The stale MIPI generic data sequence pointers would
cause a crash within those functions. However, all of this is happening
while console_lock is held from do_register_framebuffer inside fbcon.c. Which
means that you got kernel log and just the device appearing to reboot/hang for
no apparent reason.
The fault started from the FB_EVENT_FB_REGISTERED event using the
fb_notifier_call_chain call in fbcon.c.
This regression has been introduced in
commit d3b542fcfc
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Mon Apr 14 11:00:34 2014 +0530
drm/i915: Add parsing support for new MIPI blocks in VBT
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Add regression citation.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We might be leaving the PGU Frequency (and thus vnn) high during the suspend.
Flusing the delayed work queue should take care of this.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW has many other Display Engine interrupts and GT interrupts registers.
Collecting it properly on gpu_error_state.
On debugfs all was properly listed already but besides we were also listing old
DEIER and GTIER that doesn't exist on BDW anymore. This was causing
unclaimed register messages
v2: Fix small issues of first version and don't read DEIER regs when pipe's
power well is disabled
v3: bikeshed accepted: use enum pipe pipe instead of int i for pipe interection
v4: Ben notice previous version was checking for display_power_enabled without
using propper locks. Using _unlocked version isn't reliable and we cannot
get this registers when power well is off. So let's avoid getting all DE_IER
per pipe for now. If someone think this is an useful information it can be
added later.
v5: Ben: put back debugfs stuff that might be coverred by pm_get and use
gen >= 8 trying to predict future.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81701
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: (v3) Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the actual head has progressed forward inside a batch (request),
don't accumulate hangcheck score.
As the hangcheck score in increased only by acthd jumping backwards,
the result is that we only declare an active batch as stuck if it is
trapped inside a loop. Or that the looping will dominate the batch
progression so that it overcomes the bonus that forward progress gives.
v2: Improved commit message (Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: s/active_loop/active (loop)/ as requested by Chris.]
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Broadwell, any PIPE_CONTROL with the "State Cache Invalidate" bit set
must be preceded by a PIPE_CONTROL with the "CS Stall" bit set.
Documented on the BSpec 3D workarounds page.
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[vsyrjala: add chv w/a note too]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll want to reuse this for a workaround.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Rmove now unused int.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DDL registers can hold 7bit numbers. Make the most of those seven
bits by adjusting the threshold where we switch between the 64 vs. 32
precision multipliers.
Also we compute 'entries' to make the decision about precision, and then
we recompute the same value to calculate the actual drain latency. Just
use the already calculate 'entries' there.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GTIER and DEIER doesn't have same interface on HSW so this "or" operation
makes the information provided useless.
v2: since we have gtier variable already let's split for everybody
and avoid the strange | op.
Also avoid overriding the value that was set for vlv. In this case I
believe that we should reorganize the whole function, but I'll respect
the comment that ask to not touch the order and let this organization
work to be done later.
v3: moving VLV check to the right place.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Users often can't do anything about this since their vendors stopped
providing BIOS updates. Also we seem to be able to hack around it
with increased latency values, and thus far the only reports have
been for screens with really high resolutions. So tune it down to a
level where only developers can see it.
Also drop some of the end-user fluff.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Power users spot this and then get adventurous and try to adjust
module driver options. Nothing good ever came out of that, so
hide it better.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I've reworked psr support to no longer require x-tiling we don't
check any state protected by the Giant GEM Lock. So drop that check.
Also boo for lockdep_assert_held for not yelling when lockdep is
disabled.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Acked-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix signal_offset when recording semaphore state on BDW.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like during booting the BIOS can leave the VDD bit enabled after
system resume. So apply the same state sanitization there too. This
fixes a problem where after resume the port power domain refcount gets
unbalanced.
v2:
- unchanged
v3:
- call edp sanitizing from the encoder reset handler (Daniel)
Reported-and-tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check in vlv_crtc_clock_get if DPLL is enabled before calling dpio read.
It will not be enabled for DSI and avoid dpio read WARN dumps.
Absence of ->get_config was causing other WARN dumps as well. Update
dpll_hw_state as well correctly
v2: Address review comments by Daniel
- Check if DPLL is enabled rather than checking pipe output type
- set adjusted_mode->flags to 0 in compute_config rather than using
pipe_config->quirks
- Add helper function in intel_dsi_pll.c and use that in intel_dsi.c
- updated dpll_hw_state correctly
- Updated commit message and title
v3: Address review comments by Imre
- Proper masking of P1, M1 fields while computing divisors
- assert in case of bpp mismatch
- guard for divide by 0 while computing pclk
- Use ARRAY_SIZE instead of direct calculation
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed by an upcoming patch too that needs to sanitize the
VDD state during resume. The additional async disabling is only needed
for the resume path, here it doesn't make a difference since we enable
VDD right after the sanitize call.
v2:
- don't set intel_dp ptr for non-eDP encoders (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ensure that the DSI packets for a particular sequence are completely
sent before going ahead in the enabling or disabling of the panel
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gcc warns that addr might be used uninitialized. It may not, but I see
why gcc gets confused.
Additionally, hiding code with side-effects inside WARN_ON() argument
seems uncool, so I moved it outside.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[danvet: Add obligatory /* shuts up gcc */ comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 7dc19d5a "drivers: convert shrinkers to new count/scan API" added
deadlock warnings that ttm_page_pool_free() and ttm_dma_page_pool_free()
are currently doing GFP_KERNEL allocation.
But these functions did not get updated to receive gfp_t argument.
This patch explicitly passes sc->gfp_mask or GFP_KERNEL to these functions,
and removes the deadlock warning.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@kernel.org> [2.6.35+]
Signed-off-by: Dave Airlie <airlied@redhat.com>
While ttm_dma_pool_shrink_scan() tries to take mutex before doing GFP_KERNEL
allocation, ttm_pool_shrink_scan() does not do it. This can result in stack
overflow if kmalloc() in ttm_page_pool_free() triggered recursion due to
memory pressure.
shrink_slab()
=> ttm_pool_shrink_scan()
=> ttm_page_pool_free()
=> kmalloc(GFP_KERNEL)
=> shrink_slab()
=> ttm_pool_shrink_scan()
=> ttm_page_pool_free()
=> kmalloc(GFP_KERNEL)
Change ttm_pool_shrink_scan() to do like ttm_dma_pool_shrink_scan() does.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@kernel.org> [2.6.35+]
Signed-off-by: Dave Airlie <airlied@redhat.com>
I can observe that RHEL7 environment stalls with 100% CPU usage when a
certain type of memory pressure is given. While the shrinker functions
are called by shrink_slab() before the OOM killer is triggered, the stall
lasts for many minutes.
One of reasons of this stall is that
ttm_dma_pool_shrink_count()/ttm_dma_pool_shrink_scan() are called and
are blocked at mutex_lock(&_manager->lock). GFP_KERNEL allocation with
_manager->lock held causes someone (including kswapd) to deadlock when
these functions are called due to memory pressure. This patch changes
"mutex_lock();" to "if (!mutex_trylock()) return ...;" in order to
avoid deadlock.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@kernel.org> [3.3+]
Signed-off-by: Dave Airlie <airlied@redhat.com>
We can use "unsigned int" instead of "atomic_t" by updating start_pool
variable under _manager->lock. This patch will make it possible to avoid
skipping when choosing a pool to shrink in round-robin style, after next
patch changes mutex_lock(_manager->lock) to !mutex_trylock(_manager->lork).
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@kernel.org> [3.3+]
Signed-off-by: Dave Airlie <airlied@redhat.com>
list_empty(&_manager->pools) being false before taking _manager->lock
does not guarantee that _manager->npools != 0 after taking _manager->lock
because _manager->npools is updated under _manager->lock.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@kernel.org> [3.3+]
Signed-off-by: Dave Airlie <airlied@redhat.com>
This series of patches add the support of DRM/KMS drivers for STMicroelectronics
chipsets stih416 and stih407.
Hardware is split in two main blocks: Compositor and TVout. Each of them
includes specific hardware IPs and the display timing are controlled by a specific
Video Timing Generator hardware IP (VTG).
Compositor is made of the follow hardware IPs:
- GDP (Generic Display Pipeline) which is an entry point for graphic (RGB)
buffers
- VDP (Video Diplay Pipeline) which is an entry point for video (YUV) buffers
- HQVDP (High Quality Video Display Processor) that supports scaling,
deinterlacing and some miscellaneous image quality improvements.
It fetches the Video decoded buffers from memory, processes them and pushes
them to the Compositor through a HW dedicated bus.
- Mixer is responsible of mixing all the entries depending of their
respective z-order and layout
TVout is divided in 3 parts:
- HDMI to generate HDMI signals, depending of chipset version HDMI phy can
change.
- HDA to generate signals for HD analog TV
- VIP to control/switch data path coming from Compositor
On stih416 compositor and Tvout are on different dies so a Video Trafic Advance
inter-die Communication mechanism (VTAC) is needed.
+---------------------------------------------+ +----------------------------------------+
| +-------------------------------+ +----+ | | +----+ +--------------------------+ |
| | | | | | | | | | +---------+ +----+ | |
| | +----+ +------+ | | | | | | | | | VIP |---->|HDMI| | |
| | |GPD +------------->| | | | | | | | | | | | +----+ | |
| | +----+ |Mixer |--|-->| | | | | |---|->| switcher| | |
| | | | | | | | | | | | | | +----+ | |
| | | | | | | | | | | | | |---->|HDA | | |
| | +------+ | |VTAC|========>|VTAC| | +---------+ +----+ | |
| | | | | | | | | | | |
| | Compositor | | | | | | | | TVout | |
| +-------------------------------+ | | | | | | +--------------------------+ |
| ^ | | | | | | ^ |
| | | | | | | | | |
| +--------------+ | | | | | | +-------------+ |
| | VTG (master) |----->| | | | | |----->| VTG (slave) | |
| +--------------+ +----+ | | +----+ +-------------+ |
|Digital die | | Analog Die|
+---------------------------------------------+ +----------------------------------------+
On stih407 Compositor and Tvout are on the same die
+-----------------------------------------------------------------+
| +-------------------------------+ +--------------------------+ |
| | | | +---------+ +----+ | |
| | +----+ +------+ | | | VIP |---->|HDMI| | |
| | |GPD +------------->| | | | | | +----+ | |
| | +----+ |Mixer |--|--|->| switcher| | |
| | +----+ +-----+ | | | | | | +----+ | |
| | |VDP +-->+HQVDP+--->| | | | | |---->|HDA | | |
| | +----+ +-----+ +------+ | | +---------+ +----+ | |
| | | | | |
| | Compositor | | TVout | |
| +-------------------------------+ +--------------------------+ |
| ^ ^ |
| | | |
| +--------------+ |
| | VTG | |
| +--------------+ |
|Digital die |
+-----------------------------------------------------------------+
In addition of the drivers for the IPs listed before a thin I2C driver (hdmiddc) is used
by HDMI driver to retrieve EDID for monitor.
To unify interfaces of GDP and VDP we create a "layer" interface called by
compositor to control both GPD and VDP.
Hardware have memory contraints (alignment, contiguous) so we use CMA drm helpers functions
to allocate frame buffer.
File naming convention is:
- sti_* for IPs drivers
- sti_drm_* for drm functions implementation.
* 'drm_kms_for_next-v8' of git://git.linaro.org/people/benjamin.gaignard/kernel:
drm: sti: Add DRM driver itself
drm: sti: add Compositor
drm: sti: add Mixer
drm: sti: add VID layer
drm: sti: add GDP layer
drm: sti: add TVOut driver
drm: sti: add HDA driver
drm: sti: add HDMI driver
drm: sti: add VTAC drivers
drm: sti: add VTG driver
drm: sti: add bindings for DRM driver
This builds upon the previous set of fixes which were pulled on 6th July.
Included in this set are:
- an update from Jean-Francois to add the missing reg documentation entry
to the device tree documentation.
- conversion of the tda998x driver to the component helpers.
* 'tda998x-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
drm/i2c: tda998x: add component support
drm/i2c: tda998x: allow re-use of tda998x support code
drm/i2c: tda998x: fix lack of required reg in DT documentation
Conflicts:
drivers/gpu/drm/i2c/tda998x_drv.c
This time around we have a mix of new hw enablement (mdp5 v1.3 /
apq8084), plus devicetree and various upstream changes (mostly
adapting to CCF vs downstream clk driver differences) for mdp4 /
apq8064. With these drm/msm patches plus a few other small patchsets
(from linaro qcom integration branch.. mostly stuff queued up for
3.17) we have the inforce ifc6410 board working, with gpu. Much nicer
to work with than ancient vendor android branch :-)
* 'msm-next' of git://people.freedesktop.org/~robclark/linux:
drm/msm/hdmi: fix HDMI_MUX_EN gpio request typo
drm/msm/hdmi: enable lpm-mux if it is present
drm/msm/mdp5: add support for MDP5 v1.3
drm/msm: fix potential deadlock in gpu init
drm/msm: use upstream iommu
drm/msm: no mmu is only error if not using vram carveout
drm/msm: fix BUG_ON() in error cleanup path
drm/msm/mdp4: add mdp axi clk
drm/msm: hdmi phy 8960 phy pll
drm/msm: update generated headers
drm/msm: DT support for 8960/8064 (v3)
drm/msm: Implement msm drm fb_mmap callback function
drm/msm: activate iommu support
drm/msm: fix double struct_mutex acquire
HDMI_MUX_EN gpio is requested. If an error occurs, the same name
should be printed (HDMI_MUX_EN) instead of HDMI_MUX_SEL (typo).
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
lpm-mux is programmed to enable HDMI connector
on the docking station for S805 chipset based
devices.
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 has several functional blocks (ie: VIG/RGB pipes, LMs, ...).
From one revision to another, these blocks' base addresses might
change due to the number of instances present in the MDP5 hw.
A way of dealing with these offset changes is to introduce
dynamic offsets 'per block'.
This change adds support for the new revision of MDP5: v1.3.
The idea is to define one hw config per MDP version and select
either one of them at runtime, after reading the MDP5 version.
Once the MDP version is known, 'per block' dynamic offsets
are initialized through a global pointer, which is then used for
read/write register access.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Somewhere along the way, the firmware loader sprouted another lock
dependency, resulting in possible deadlock scenario:
&dev->struct_mutex --> &sb->s_type->i_mutex_key#2 --> &mm->mmap_sem
which is problematic vs things like gem mmap.
So introduce a separate mutex to synchronize gpu init.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Downstream kernel IOMMU had a non-standard way of dealing with multiple
devices and multiple ports/contexts. We don't need that on upstream
kernel, so rip out the crazy.
Note that we have to move the pinning of the ringbuffer to after the
IOMMU is attached. No idea how that managed to work properly on the
downstream kernel.
For now, I am leaving the IOMMU port name stuff in place, to simplify
things for folks trying to backport latest drm/msm to device kernels.
Once we no longer have to care about pre-DT kernels, we can drop this
and instead backport upstream IOMMU driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Downstream kernel holds this clk via a fake-parent relationship.
Upstream clock framework requires that we hold it explicitly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
On downstream kernel the clk driver directly bangs hdmi phy registers.
For upstream kernel, we need to model this as a clock and register with
the clock framework.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that we (almost) have enough dependencies in place (MMCC, RPM, etc),
add necessary DT support so that we can use drm/msm on upstream kernel.
v2: update for review comments
v3: rebase on component helper changes
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change implements msm drm specific fb_mmap function for fb device
to properly map the fb address to userspace.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com> (+ minor comment tweak)
This changes activates the iommu support for MDP5, through the
platform config structure.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Final feature pull for 3.17.
drm-intel-next-2014-07-25:
- Ditch UMS support (well just the config option for now)
- Prep work for future platforms (Sonika Jindal, Damien)
- runtime pm/soix fixes (Paulo, Jesse)
- psr tracking improvements, locking fixes, now enabled by default!
- rps fixes for chv (Deepak, Ville)
- drm core patches for rotation support (Ville, Sagar Kamble) - the i915 parts
unfortunately didn't make it yet
- userptr fixes (Chris)
- minimum backlight brightness (Jani), acked long ago by Matthew Garret on irc -
I've forgotten about this patch :(
QA is a bit unhappy about the DP MST stuff since it broke hpd testing a
bit, but otherwise looks sane. I've backmerged drm-next to resolve
conflicts with the mst stuff, which means the new tag itself doesn't
contain the overview as usual.
* tag 'drm-intel-next-2014-07-25-merged' of git://anongit.freedesktop.org/drm-intel: (75 commits)
drm/i915/userptr: Keep spin_lock/unlock in the same block
drm/i915: Allow overlapping userptr objects
drm/i915: Ditch UMS config option
drm/i915: respect the VBT minimum backlight brightness
drm/i915: extract backlight minimum brightness from VBT
drm/i915: Replace HAS_PCH_SPLIT which incorrectly lets some platforms in
drm/i915: Returning from increase/decrease of pllclock when invalid
drm/i915: Setting legacy palette correctly for different platforms
drm/i915: Avoid incorrect returning for some platforms
drm/i915: Writing proper check for reading of pipe status reg
drm/i915: Returning the right VGA control reg for platforms
drm/i915: Allowing changing of wm latencies for valid platforms
drm/i915: Adding HAS_GMCH_DISPLAY macro
drm/i915: Fix possible overflow when recording semaphore states.
drm/i915: Do not unmap object unless no other VMAs reference it
drm/i915: remove plane/cursor/pipe assertions from intel_crtc_disable
drm/i915: Reorder ctx unref on ppgtt cleanup
drm/i915/error: Check the potential ctx obj's vm
drm/i915: Fix printing proper min/min/rpe values in debugfs
drm/i915: BDW can also detect unclaimed registers
...
Daniel pointed out with hotplug that userspace could be trying to oops us
as root for lols, and that to be correct we shouldn't register the object
with the idr before we have fully set the connector object up.
His proposed solution was a lot more life changing, this seemed like a simpler
proposition to me, get the connector object id from the idr, but don't
register the object until the drm_connector_register callback.
The open question is whether the drm_mode_object_register needs a bigger lock
than just the idr one, but I can't see why it would, but I can be locking
challenged.
v2: fix bool noreg into sane - add comment.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On HSW+, the digital encoders are shared between HDMI and DP outputs,
with one encoder masquerading as both. The VBT should tell us if we need
to have DP or HDMI support on a particular port, but if we don't have DP
support and we enable the DP hpd pulse handler then we cause an oops.
Don't hook up the DP hpd handling if we don't have a DP port.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81856
Reported-by: Intel QA Team.
Signed-off-by: Dave Airlie <airlied@redhat.com> # v1
[ickle: Fix the error handling after a malloc failure]
Reviewed-by: Dave Airlie <airlied@redhat.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently the DRM_IOCTL_EXYNOS_G2D_GET_VER ioctl always succeeds, even
if no G2D support is available. Let the ioctl fail when this is the
case, so that userspace can accurately probe for G2D support.
This also fixes the exynos tests in libdrm. There 'g2d_init' doesn't
fail when G2D is absent, leading to a segfault later.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: INki Dae <inki.dae@samsung.com>
Both exynos_g2d_set_cmdlist_ioctl and exynos_g2d_exec_ioctl don't check
if the G2D was succesfully probe. If that is not the case, then g2d_priv
is just NULL and extracting 'dev' from it in the next step is going to
produce a kernel oops.
Add proper checks and return ENODEV if the G2D is not available.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: INki Dae <inki.dae@samsung.com>
The hdmiphy can be apb and hdmiphy_port can be null. So before
accessing hdmiphy_port, it should be checked.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The mixer graphic layer 0 isn't blended as default by commit
0377f4ed9f1aed30292c4e3c87f24e028ae26f36(drm/exynos: Don't blend mixer
layer 0). But it needs to be blended with graphic layer 0 if video layer
is enabled by vp because video layer is bottom.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Add MODULE_DEVICE_TABLE calls for the various OF match tables that
currently don't have one. This allows the module to be
autoloaded based on devicetree information.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This reverts commit d089621896 was
original to prevent multiple MODULE_DEVICE_TABLE in one module.
Which, as a side-effect broke autoloading of the module.
Since 21bdd17b21 it is possible to have
multiple calls to MODULE_DEVICE_TABLE, so the patch can be
reverted to restore support for autoloading
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since 21bdd17b21 it is possible to have
multiple calls to MODULE_DEVICE_TABLE, so the patch can be
reverted to restore support for autoloading
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_fimd.c
drivers/gpu/drm/exynos/exynos_drm_g2d.c
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch puts repeated code sequence into one function, removes verbose
comments and decreases log verbosity.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no gain in passing id by pointer to be filled.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
In case of error callback prints already corresponding message.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Argument checks are redundant, clients always check ippdrv before calling
these functions.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The only thing function should check is if there are buffers in respective
queues.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
list_first_entry does not return NULL on empty list so this check
does not make sense. Moreover there is already code which prevents calling
list_first_entry on empty lists.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no reason to allocate intermediate variable.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
exynos_drm_gem_get_dma_addr returns dma_addr_t, type casting to void* and
back is not necessary.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
struct exynos_drm_ipp_private contains only one pointer so all occurrences
of the struct can be replaced by the pointer itself.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch removes unused event_list field from struct exynos_drm_ipp_private.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The offset of register DSIM_PLLTMR_REG in Exynos5410 / 5420 / 5440
SoCs is different from the one in Exynos4 SoCs.
In case of Exynos5410 / 5420 / 5440 SoCs, there is no frequency
band bit in DSIM_PLLCTRL_REG, and it uses DSIM_PHYCTRL_REG and
DSIM_PHYTIMING*_REG instead.
So this patch adds driver data to distinguish it.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
To support MIPI command mode based I80 interface panel,
FIMD should do followings:
- Sets LCD I80 interface timings configuration.
- Uses "lcd_sys" as an IRQ resource and sets relevant IRQ configuration.
- Sets LCD block configuration for I80 interface.
- Sets ideal(pixel) clock is 2 times faster than the original one
to generate frame done IRQ prior to the next TE signal.
- Implements trigger feature that transfers image data if there is page
flip request, and implements TE handler to call trigger function.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This is a temporary solution and should be made by more
generic way.
To support LCD I80 interface, the DSI host should register
TE interrupt handler from the TE GPIO of attached panel.
So the panel generates a tearing effect synchronization signal
then the DSI host calls the CRTC device manager to trigger
to transfer video image.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
To support LCD I80 interface, the panel should generate
Tearing Effect synchronization signal between MCU and FB
to display video images.
And the display controller should trigger to transfer
video image at this signal.
So the panel receives the TE IRQ, then calls these handler
chains to notify it to the display controller.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There could be the case that the page flip operation isn't finished correctly
with some abnormal condition such as panel reset. So this patch replaces
wait_event() with wait_event_timeout() to avoid waiting for page flip completion
infinitely.
And clears exynos_crtc->pending_flip in exynos_drm_crtc_page_flip()
when exynos_drm_crtc_mode_set_commit() is failed.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This configuration could be used in MIPI DSI command mode also.
And adds user manual description for display configuration.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Configuration sets for Exynos 4210 and 4x12 SoC were already defined in
Exynos HDMI and Mixed drivers, but they lacked proper linking to device
tree 'compatible' values. This patch fixes this issue adding support for
following compatible values: samsung,exynos4210-mixer,
samsung,exynos4212-mixer and samsung,exynos4210-hdmi. It also corrects
access to sclk_mixer clock, which is available only on Exynos 4210.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
HDMI_EN regulator is additional regulator for providing voltage source
for DCC lines available on HDMI connector. When there is no power
provided for DDC epprom, some TV-sets do not pulls up HPD (hot plug
detect) line, what causes HDMI block to stay turned off. This patch
enables HDMI_EN regulator (if available) on driver probe and keep it
enabled all the time to let TV-set correctly signal HPD event.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
According to the header comment in the source file, the driver is
licensed under GPL v2, so update MODULE_LICENSE() to match that.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
'exynos_gem_obj' is not used in the function. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
'frame_size_code' is not used in the function. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Linux doesn't run on i386, anymore. See:
commit d55c5a93db
Author: H. Peter Anvin <hpa@linux.intel.com>
Date: Wed Nov 28 11:50:24 2012 -0800
x86, 386 removal: Remove CONFIG_CMPXCHG
All 486+ CPUs support CMPXCHG, so remove the fallback 386 support
code.
Furthermore, as the commit-message states, all 486+ CPUs support the
CMPXCHG instruction and thus even legacy DRM can run fine.
Drop the now superfluous "x86 == 3" check.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This object is not used except for static fields in drm_bufs *cough*.
Inline the watermark fields and drop the unused structure definition.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add component helper support to the tda998x driver. This permits the
TDA998x to be declared as a separate device in device tree, and bound
at the appropriate moment with a co-operating card driver.
The existing slave_encoder interfaces are kept while there are existing
users of it in order to prevent regressions.
Tested-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Re-jig the TDA998x code so that we separate the functionality from the
drm slave encoder implementation. In several places, this is pretty
clearly the correct thing to do, because we can avoid repetitively
having to convert from the drm_encoder to the TDA998x private
structure, particularly with the driver internal functions.
The main motivation behind this change is to allow the code to be
re-used with a standard drm_encoder and drm_connector implementation
based on the component helpers, rather than the slave_encoder system.
The addition of this will be in the following patch.
We keep the slave_encoder interface as there are existing users of
this; we need to give them time to convert and test.
Tested-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the link between all the hardware drivers and DRM/KMS interface.
Create the driver itself and make it register all the sub-components.
Use GEM CMA helpers for buffer allocation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Compositor control all the input sub-device (VID, GDP)
and the mixer(s).
It is the main entry point for composition.
Layer interface is used to control the abstracted layers.
Add debug in mixer and GDP.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Mixer hardware IP is responsible of mixing the different inputs layers.
Z-order is managed by the mixer.
We could 2 mixers: one for main path and one for auxillary path
Mixers are part of Compositor hardware block
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
VIDeo plug are one of the compositor input sub-devices.
VID are dedicated to video inputs like YUV plans.
Like GDP, VID are part of Compositor hardware block
and use sti_layer structure to provide an abstraction for
Compositor calls.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Generic Display Pipeline are one of the compositor input sub-devices.
GDP are dedicated to graphic input like RGB plans.
GDP is part of Compositor hardware block which will be introduce later.
A sti_layer structure is used to abstract GDP calls from Compositor.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
TVout hardware block is responsible to dispatch the data flow coming
from compositor block to any of the output (HDMI or Analog TV).
It control when output are start/stop and configure according the
require flow path.
TVout is the parent of HDMI and HDA drivers and bind them at runtime.
Tvout is mapped on drm_encoder structure.
One encoder is created for each of the sub-devices and link to their
connector/bridge
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Add driver to support analog TV ouput.
HDA driver is mapped on drm_bridge and drm_connector structures.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Add driver for HDMI output.
HDMI PHY registers are mixed into HDMI device registers
and their is only one IRQ for all this hardware block.
That is why PHYs aren't using phy framework but only a
thin hdmi_phy_ops structure with start and stop functions.
HDMI driver is mapped on drm_bridge and drm_connector structures.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Video Traffic Advance Communication Rx and Tx drivers are designed
for inter-die communication.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Video Time Generator drivers are used to synchronize the compositor
and tvout hardware IPs by providing line count, sample count,
synchronization signals (HSYNC, VSYNC) and top and bottom fields
indication.
VTG are used by pair for each data path (main or auxiliary)
one for master and one for slave.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Add DRM/KMS driver bindings documentation.
Describe the required properties for each of the hardware IPs drivers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
The maximum pitch constraint for the hardware is expressed in pixels.
Convert it to bytes to validate frame buffer creation, as frame buffer
pitches are expressed in bytes.
Reported-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull in drm-next with Dave's DP MST support so that I can merge some
conflicting patches which also touch the driver load sequencing around
interrupt handling.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the code around in order to acquire and release the spinlock in the
same function and in the same block. This keeps static analysers happy
and the reader sane.
Suggested-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a halfway fix for hawaii acceleration. More fixes to come
but hopefully isolated to userspace.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
two more radeon fixes.
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix irq ring buffer overflow handling
drm/radeon: fix error handling in radeon_vm_bo_set_addr
This time in time! Just 32bit-pae fix from Hugh, semaphores fun from Chris
and a fix for runtime pm cherry-picked from next.
Paulo is still working on a fix for runtime pm when X does cursor fun when
the display is off, but that one isn't ready yet.
* tag 'drm-intel-fixes-2014-07-24' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Simplify i915_gem_release_all_mmaps()
drm/i915: fix freeze with blank screen booting highmem
drm/i915: Reorder the semaphore deadlock check, again
Whilst I strongly advise against doing so for the implicit coherency
issues between the multiple buffer objects accessing the same backing
store, it nevertheless is a valid use case, akin to mmaping the same
file multiple times.
The reason why we forbade it earlier was that our use of the interval
tree for fast invalidation upon vma changes excluded overlapping
objects. So in the case where the user wishes to create such pairs of
overlapping objects, we degrade the range invalidation to walkin the
linear list of objects associated with the mm.
A situation where overlapping objects could arise is the lax implementation
of MIT-SHM Pixmaps in the xserver. A second situation is where the user
wishes to have different access modes to a region of memory (e.g. access
through a read-only userptr buffer and through a normal userptr buffer).
v2: Compile for mmu-notifiers after tweaking
v3: Rename is_linear/has_linear
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Li, Victor Y" <victor.y.li@intel.com>
Cc: "Kelley, Sean V" <sean.v.kelley@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Gong, Zhipeng" <zhipeng.gong@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Cc: "Volkin, Bradley D" <bradley.d.volkin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's march ahead with the deprecation plan laid out in
commit b30324adaf
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Nov 13 22:11:25 2013 +0100
drm/i915: Deprecated UMS support
Thus far no regression report yet, so the transparent fallback plan
seems to pan out.
Cc: Dave Airlie <airlied@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Suggested-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This chunk was no longer required from what I can see, or
at least it is doing the wrong thing, as I confused
intel_connector->encoder and connector->encoder. Drop it
for now, to remove the warnings at bootup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
When I moved the irq disable down to after display disable,
I didn't realise the gt suspend also required irqs off, so move it
down as well.
Fixes WARNs seen at suspend/resume time.
v2: moved the rps flush down as well.
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We must mask out the overflow bit as well, otherwise
the wptr will never match the rptr again and the interrupt
handler will loop forever.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
An object can only have an active gtt mapping if it is currently bound
into the global gtt. Therefore we can simply walk the list of all bound
objects and check the flag upon those for an active gtt mapping.
From commit 48018a57a8
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Dec 13 15:22:31 2013 -0200
drm/i915: release the GTT mmaps when going into D3
Also note that the WARN is inappropriate for this function as GPU
activity is orthogonal to GTT mmap status. Rather it is the caller that
relies upon this condition and so it should assert that the GPU is idle
itself.
References: https://bugs.freedesktop.org/show_bug.cgi?id=80081
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: cherry-pick from -next to -fixes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Historically we've exposed the full backlight PWM duty cycle range to
the userspace, in the name of "mechanism, not policy". However, it turns
out there are both panels and board designs where there is a minimum
duty cycle that is required for proper operation. The minimum duty cycle
is available in the VBT.
The backlight class sysfs interface does not make any promises to the
userspace about the physical meaning of the range
0..max_brightness. Specifically there is no guarantee that 0 means off;
indeed for acpi_backlight 0 usually is not off, but the minimum
acceptable value.
Respect the minimum backlight, and expose the range acceptable to the
hardware as 0..max_brightness to the userspace via the backlight class
device; 0 means the minimum acceptable enabled value. To switch off the
backlight, the user must disable the encoder.
As a side effect, make the backlight class device max brightness and
physical PWM modulation frequency (i.e. max duty cycle)
independent. This allows a follow-up patch to virtualize the max value
exposed to the userspace.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: s/BUG_ON/WARN_ON/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Adding IS_G4X instead of gen < 5 as suggested by Daniel
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
semaphore _sync_seqno, _seqno and _mbox are smaller than number of rings.
This optimization is to remove the ring itself from the list and the logic to do that
is at intel_ring_sync_index as below:
/*
* rcs -> 0 = vcs, 1 = bcs, 2 = vecs, 3 = vcs2;
* vcs -> 0 = bcs, 1 = vecs, 2 = vcs2, 3 = rcs;
* bcs -> 0 = vecs, 1 = vcs2. 2 = rcs, 3 = vcs;
* vecs -> 0 = vcs2, 1 = rcs, 2 = vcs, 3 = bcs;
* vcs2 -> 0 = rcs, 1 = vcs, 2 = bcs, 3 = vecs;
*/
v2: Skip when from == to (Damien).
v3: avoid computing idx when from == to (Damien).
use ring == to instead of ring->id == to->id (Damien).
use continue instead of return (Rodrigo).
v4: avoid all unecessary computation (Damien).
reduce idx to loop scope (Damien).
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When using an IOMMU, GEM objects are mapped by their DMA address as the
physical address is unknown. This depends on the underlying IOMMU
driver to map and unmap the physical pages properly as defined in
intel_iommu.c.
The current code will tell the IOMMU to unmap the GEM BO's pages on the
destruction of the first VMA that "maps" that BO. This is clearly wrong
as there may be other VMAs "mapping" that BO (using flink). The scanout
is one such example.
The patch fixes this issue by only unmapping the DMA maps when there are
no more VMAs mapping that object. This is equivalent to when an object
is considered unbound as can be seen by the code. On the first VMA that
again because bound, we will remap.
An alternate solution would be to move the dma mapping to object
creation and destrubtion. I am not sure if this is considered an
unfriendly thing to do.
Some notes to backporters trying to backport full PPGTT:
The bug can never be hit without enabling the IOMMU. The existing code
will also do the right thing when the object is shared via dmabuf. The
failure should be demonstrable with flink. In cases when not using
intel_iommu_strict it is likely (likely, as defined by: off the top of
my head) on current workloads to *not* hit this bug since we often
teardown all VMAs for an object shared across multiple VMs. We also
finish access to that object before the first dma_unmapping.
intel_iommu_strict with flinked buffers is likely to hit this issue.
Signed-off-by: Armin Reese <armin.c.reese@intel.com>
[danvet: Add the excellent commit message provided by Ben.]
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we merged runtime PM support for DPMS, it is possible that these
assertions will be called when the power wells are disabled but a mode
is "set", resulting in "failed assertion" and "device suspended while
reading register" WARNs.
To reproduce the bug: disable all screens using mode unset, do a
modeset on one screen, disable it using DPMS, then try to do a mode
unset on it again to see the WARNs.
v2: The first version of this patch changed the assertions to also
check the power domains. Daniel suggested that it would be better to
just remove the assertions: "The modeset state checker
will already notice when we've failed to turn off the pipe. And we
check cursors and plane state in the enable sequence, too. Since we
use these asserts a lot to lock down the precise modeset sequence I
actually prefer if they're a bit dumb and don't check the power
wells."
Testcase: igt/rpm_rpm/dpms-mode-unset-lpsp
Testcase: igt/rpm_rpm/dpms-mode-unset-non-lpsp
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The comment [which was mine] is wrong. The context object can never be
bound in a PPGTT because it is only capable of living in the Global GTT.
So, remove the comment, and reorder the unref. What's nice about the
latter is it keeps the context object alive past the PPGTT. This makes
the destroy ordering symmetric with the creation ordering.
Create:
1. Create context
2. Create PPGTT
Destroy:
1. Destroy PPGTT
2. Destroy context
As far as I know, this does not fix a bug. The code previously kept the
context data structure, only the object was gone. As the code was,
nothing tried to use the object after this point.
NOTE: If in the future we have cases where the PPGTT can/should outlive
the context (which doesn't occur today, but the code permits it), this
ordering does not matter. Even if this occurs, as it stands now, we do
not expect that to be the normal case, and having this order makes
debugging a bit easier if we're tracking object lifetimes for the
context vs ppgtt
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Resolve conflict with Oscar's execlist prep patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bound list is global (all objects which back the VMAs are stored
here). Recently the BUG() in the offset lookup was demoted to a WARN,
but the fault actually lies in the caller, here.
This bug has existed since the initial introduction of PPGTT (however,
it was fixed in unmerged patches to fix up the error state).
Note: The reason for the BUG_ON to WARN_ON demotion was _not_ to
duct-tape over this bug here but another but triggerable without
ppgtt. See the commit for details:
commit f25748ea73
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jun 17 22:34:38 2014 +0200
drm/i915: Don't BUG_ON in i915_gem_obj_offset
A WARN_ON is perfectly fine.
The BUG in here seems to be the cause behind hard-hangs when I cat the
i915_gem_pageflip debugfs file (which calls this from an irq
spinlock). But only while running a full igt run after a while. I
still need to root cause the underlying issue.
I'll also start reject patches which add new BUG_ON but don't come
with a really good justification for it. The general rule really
should be to just WARN and hope the driver survives for long enough.
v2: Make the WARN a bit more useful per Chris' suggestion.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Clarfy that the WARN_ON (former BUG_ON) in ggtt_offset caught
more than just this bug fixed in this patch here.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was fumbled while trying to use the cached min/min/rpe values in
the vlv debugfs code.
This is a regression from
commit 03af20458a
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Sat Jun 28 02:03:53 2014 +0300
drm/i915: Use the cached min/min/rpe values in the vlv debugfs code
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By the time I wrote this patch, it allowed me to catch some problems.
But due to patch reordering - in order to prevent fake "regression"
reports - this patch may be merged after the fixes of the problems
identified by this patch.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code only runs when we do an I915_WRITE operation. It
checks if the unclaimed register flag is set before we do the
operation, and then it checks it again after we do the operation. This
double check allows us to find out if the I915_WRITE operation in
question is the bad one, or if some previous code is the bad one. When
it finds a problem, our code uses DRM_ERROR to signal it.
The good thing about the current code is that it detects the problem,
so at least we can know we did something wrong. The problem is that
even though we find the problem, we don't really have much information
to actually debug it. So whenever I see one of these DRM_ERROR
messages on my systems, the first thing I do is apply a patch to
change the DRM_ERROR to a WARN and also check for unclaimed registers
on I915_READ operations. This local patch makes things even slower,
but it usually helps a lot in finding the bad code.
The first point here is that since the current code is only useful to
detect whether we have a problem or not, but it is not really good to
find the cause of the problem, I don't think we should be checking
both before and after every I915_WRITE operation: just doing the check
once should be enough for us to quickly detect problems. With this
change, the code that runs by default for every single user will only
do 1 read operation for every single I915_WRITE, instead of 2. This
patch does this change.
The second point is that the local patch I have should be upstream,
but since it makes things slower it should be disabled by default. So
I added the i915.mmio_debug option to enable it.
So after this patch, this is what will happen:
- By default, we will try to detect unclaimed registers once after
every I915_WRITE operation. Previously we tried twice for every
I915_WRITE.
- When we find an unclaimed register we will still print a DRM_ERROR
message, but we will now tell the user to try again with
i915.mmio_debug=1.
- When we use i915.mmio_debug=1 we will try to find unclaimed
registers both before and after every I915_READ and I915_WRITE
operation, and we will print stack traces in case we find them.
This should really help locating the exact point of the bad code
(or at least finding out that i915.ko is not the problem).
This commit also opens space for really-slow register debugging
operations on other platforms. In theory we can now add lots and lots
of debug code behind i915.mmio_debug, enable this option on our tests,
and catch more problems.
v2: - Remove not-so-useful comments (Daniel)
- Fix the param definition macros (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After this point, we'll modify it with the runtime routines.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before we've installed the handler, we can set this and avoid confusing
init code that then thinks IRQs are enabled and spews complaints
everywhere.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we use the runtime IRQ enable/disable functions in our suspend
path, we can simply check the pm._irqs_disabled flag everywhere. So
rename it to catch the users, and add an inline for it to make the
checks clear everywhere.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was always the case on our suspend path, but it was recently
exposed by the change to use our runtime IRQ disable routine rather than
the full DRM IRQ disable. Keep the warning on the enable side, as that
really would indicate a bug.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move it from hsw_power_well_post_enable() (intel_pm.c) to i915_irq.c
so we can reuse the nice IRQ macros we have there. The main difference
is that now we're going to check if the IIR register is non-zero when
we try to re-enable the interrupts.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So don't write it, otherwise we will trigger unclaimed register
errors.
Testcase: igt/pm_rpm/rte
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we enable unclaimed register reporting on Gen 8, we will discover
that the IRQ registers for pipes B and C are also on the power well,
so writes to them when the power well is disabled result in unclaimed
register errors.
Also, hsw_power_well_post_enable() already takes care of re-enabling
them once the power well is enabled.
Testcase: igt/pm_rpm/rte
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Traditionally we use genX_ for GT/render stuff and the codenames for
display stuff. But the gt and pm interrupt handling functions on
gen5/6+ stuck out as exceptions, so convert them.
Looking at the diff this nicely realigns our ducks since almost all
the callers are already platform-specific functions following the
genX_ pattern.
Spotted while reviewing some internal rps patches.
No function change in this patch.
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During the range invalidate, we walk the list of buffers associated with
the mmu_notifer and find the ones that overlap the range. An
optimisation is made to speed up the iteration by assuming the previous
iter is still valid whilst the tree is unmodified. This exposes a bug
when a range invalidate is triggered after we have just created the
mmu_notifier, but before attaching any buffers. In that case, we presume
we have an unmodified list and start walking from the last iter which is
NULL. Oops.
The easiest fix is then to initialise the serial of the tree to 1.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Testecase: igt/gem_userptr_blts/stress-mm
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whilst waiting to obtain our locks for the last resort shrinking before
an oom, we check whether or not a fatal signal was pending. If there was,
we do not need to keep waiting as the oom will be aborted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the future, we'll need the height of the fb to fetch from memory for
WM computation.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to list all the platforms explicitly.
The prefix is a bit inconsistent since we usually pick gen8_ for GT
related functions. But this anti-pattern is already established with snb,
so material for a different patch.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Create and attach the drm property to set aspect ratio. If there is no user
specified value, then PAR_NONE/Automatic option is set by default. User can
select aspect ratio 4:3 or 16:9. The aspect ratio selected by user would
come into effect with a mode set.
v2: Modified switch case to include aspect ratio enum changes
v3: Modified the patch according the change in the earlier patch to return
errno in case property creation fails. With this change, property will be
attached only if creation is successful
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case user has specified an input for aspect ratio through the property,
then the user space value for PAR would take preference over the value from
CEA mode list.
v2: Thierry's review comments.
- Modified the comment "Populate..." as per review comments
v3: Thierry's review comments.
- Modified the comment to block comment format.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added a property to enable user space to set aspect ratio.
This patch contains declaration of the property and code to create the
property.
v2: Thierry's review comments.
- Made aspect ratio enum generic instead of HDMI/CEA specfic
- Removed usage of temporary aspect_ratio variable
v3: Thierry's review comments.
- Fixed indentation
v4: Thierry's review comments.
- Return ENOMEM when property creation fails
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop WaGsvBringDownFreq on CHV.
When in RC6 requesting the min freq should be fine to bring the
voltage down.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@Virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already call intel_display_power_get, which will get a power
domain, and every power domain should get a runtime PM reference,
which will wake up the machine.
v2: - Also touch intel_crt_detect() (Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Fixup commit message as spotted by Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We might be leaving the GPU Frequency (and thus vnn) high during the suspend.
Force gt to move to lowest freq while suspending.
v2: Fixed typo in commit message (Deepak)
v3: Force gt to lowest freq in suspend_gt_powersave (Daniel)
v4: Add GPU min freq set _after_ we've cancelled the rps works (Daniel)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Panel Self Refresh is an eDP power saving feature specified by VESA's eDP v1.3,
that allows some panel componets to shutdown while you still see static images on
the screen. Besides being supported on the platform it must be supported by the
eDP panel itself.
Now that we have the propper frontbuffer tracking support and correct locks on place
we can enabled this feature by default.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>