[ Upstream commit 5c7d55bded ]
Add support for mcan bit timing and control mode according to bosch mcan IP
version 3.3.0. The mcan version read from the Core Release field of CREL
register would be 33. Accordingly the properties are to be set for mcan v3.3.0
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/1606366302-5520-1-git-send-email-pankj.sharma@samsung.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3409e4192 ]
At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid
register values for "Nominal Time segment after sample point (NTSEG2)" are from
1 to 127. As the hardware uses a value of one more than the programmed value,
mean tseg2_min is 2.
This patch fixes the tseg2_min value accordingly.
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Mario Huettel <mario.huettel@gmx.net>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de
Fixes: b03cfc5bb0 ("can: m_can: Enable M_CAN version dependent initialization")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 865f5b671b ]
The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.
Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:
| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt
This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ba1cb39fc ]
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1f634463a ]
Avoid processing bogus interrupt statuses when the HW is runtime suspended and
the M_CAN_IR register read may get all bits 1's. Handler can be called if the
interrupt request is shared with other peripherals or at the end of free_irq().
Therefore check the runtime suspended status before processing.
Fixes: cdf8259d65 ("can: m_can: Add PM Support")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200915134715.696303-1-jarkko.nikula@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd9f13c594 ]
If the CAN controller goes into bus off, the do_set_mode() callback with
CAN_MODE_START can be used to recover the controller, which then calls
flexcan_chip_start(). If configured, this is done automatically by the
framework or manually by the user.
In flexcan_chip_start() there is an explicit call to
flexcan_transceiver_enable(), which does a regulator_enable() on the
transceiver regulator. This results in a net usage counter increase, as there
is no corresponding flexcan_transceiver_disable() in the bus off code path.
This further leads to the transceiver stuck enabled, even if the CAN interface
is shut down.
To fix this problem the
flexcan_transceiver_enable()/flexcan_transceiver_disable() are moved out of
flexcan_chip_start()/flexcan_chip_stop() into flexcan_open()/flexcan_close().
Fixes: e955cead03 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20201118150148.2664024-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d003868d7f ]
Use correct bittiming limits for the KCAN CAN controller.
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20201115163027.16851-2-jimmyassarsson@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a584e9bc1b ]
There might be some requests pending in the buffer when the interface close
sequence occurs. In some devices, these pending requests might lead to the
module not shutting down properly when m_can_clk_stop() is called.
Therefore, move the device to init state before potentially powering it down.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8c22f5b0c ]
This patch creates a common function that peripherials can call to free the
netdev device when failures occur.
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20200227183829.21854-2-dmurphy@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd0d83eab2 ]
m_can_handle_state_change() is called with the new_state as an argument.
In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the
following code indicate that a CAN_STATE_ERROR_WARNING is handled.
This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING.
Signed-off-by: Wu Bo <wubo.oduw@gmail.com>
Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81d0b6ca6 ]
Change the order in tcan4x5x_can_remove() to be the exact inverse of
tcan4x5x_can_probe(). First m_can_class_unregister(), then power down the
device.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20201019154233.1262589-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fcce133f0 ]
regmap is a library function that gets selected by drivers that need it. No
driver modules should depend on it. Instead depends on SPI and select
REGMAP_SPI. Depending on REGMAP_SPI makes this driver only build if another
driver already selected REGMAP_SPI, as the symbol can't be selected through the
menu kernel configuration.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: http://lore.kernel.org/r/20200413141013.506613-1-enric.balletbo@collabora.com
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7ee5bc3e1 ]
pm_runtime_get_sync() will increment pm usage at first and it will resume the
device later. If runtime of the device has error or device is in inaccessible
state(or other error state), resume operation will fail. If we do not call put
operation to decrease the reference, it will result in reference leak in the
two functions flexcan_get_berr_counter() and flexcan_open().
Moreover, this device cannot enter the idle state and always stay busy or other
non-idle state later. So we should fix it through adding
pm_runtime_put_noidle().
Fixes: ca10989632 ("can: flexcan: implement can Runtime PM")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201108083000.2599705-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a68cc0d69 ]
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit variable. In the case where
time_ref->adapter->ts_used_bits is 32 or more this can lead to an oveflow.
Avoid this by shifting using the BIT_ULL macro instead.
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201105112427.40688-1-colin.king@canonical.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81c9c8e0ad ]
The driver has to first fill the skb with data and then handle it to
can_put_echo_skb(). This patch moves the can_put_echo_skb() down, right before
sending the skb out via USB.
Fixes: 51f3baad7d ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Link: https://lore.kernel.org/r/20201111221204.1639007-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7968c7c79d ]
In the error handling, we should goto the probe_exit_candev
to free ndev to prevent memory leak.
Fixes: dabf54dd1c ("can: ti_hecc: Convert TI HECC driver to DT only driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201114111708.3465543-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1e654070a ]
netif_rx() is meant to be called from interrupt contexts. can_restart() may be
called by can_restart_work(), which is called from a worqueue, so it may run in
process context. Use netif_rx_ni() instead.
Fixes: 39549eef35 ("can: CAN Network device driver and Netlink interface")
Co-developed-by: Loris Fauster <loris.fauster@ttcontrol.com>
Signed-off-by: Loris Fauster <loris.fauster@ttcontrol.com>
Signed-off-by: Alejandro Concepcion Rodriguez <alejandro@acoro.eu>
Link: https://lore.kernel.org/r/4e84162b-fb31-3a73-fa9a-9438b4bd5234@acoro.eu
[mkl: use netif_rx_ni() instead of netif_rx_any_context()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93ef65e5a6 ]
Echo management is driven by PUCAN_MSG_LOOPED_BACK bit, while loopback
frames are identified with PUCAN_MSG_SELF_RECEIVE bit. Those bits are set
for each outgoing frame written to the IP core so that a copy of each one
will be placed into the rx path. Thus,
- when PUCAN_MSG_LOOPED_BACK is set then the rx frame is an echo of a
previously sent frame,
- when PUCAN_MSG_LOOPED_BACK+PUCAN_MSG_SELF_RECEIVE are set, then the rx
frame is an echo AND a loopback frame. Therefore, this frame must be
put into the socket rx path too.
This patch fixes how CAN frames are handled when these are sent while the
can interface is configured in "loopback on" mode.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Link: https://lore.kernel.org/r/20201013153947.28012-1-s.grosjean@peak-system.com
Fixes: 8ac8321e4a ("can: peak: add support for PEAK PCAN-PCIe FD CAN-FD boards")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecc7b4187d ]
Fabian Inostroza <fabianinostrozap@gmail.com> has discovered a potential
problem in the hardware timestamp reporting from the PCAN-USB USB CAN interface
(only), related to the fact that a timestamp of an event may precede the
timestamp used for synchronization when both records are part of the same USB
packet. However, this case was used to detect the wrapping of the time counter.
This patch details and fixes the two identified cases where this problem can
occur.
Reported-by: Fabian Inostroza <fabianinostrozap@gmail.com>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Link: https://lore.kernel.org/r/20201014085631.15128-1-s.grosjean@peak-system.com
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6921dd524 ]
These values come from skb->data so Smatch considers them untrusted. I
believe Smatch is correct but I don't have a way to test this.
The usb_if->dev[] array has 2 elements but the index is in the 0-15
range without checks. The cfd->len can be up to 255 but the maximum
valid size is CANFD_MAX_DLEN (64) so that could lead to memory
corruption.
Fixes: 0a25e1f4f1 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200813140604.GA456946@mwanda
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e002103b36 ]
The driver forgets to call clk_disable_unprepare() in error path after
a success calling for clk_prepare_enable().
Fix it by adding a clk_disable_unprepare() in error path.
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1594973079-27743-1-git-send-email-zhangchangzhong@huawei.com
Fixes: befa60113c ("can: ti_hecc: add missing prepare and unprepare of the clock")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed3320cec2 ]
The can_get_echo_skb() function returns the number of received bytes to
be used for netdev statistics. In the case of RTR frames we get a valid
(potential non-zero) data length value which has to be passed for further
operations. But on the wire RTR frames have no payload length. Therefore
the value to be used in the statistics has to be zero for RTR frames.
Reported-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201020064443.80164-1-socketcan@hartkopp.net
Fixes: cf5046b309 ("can: dev: let can_get_echo_skb() return dlc of CAN frame")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2283f79b22 ]
If a driver calls can_get_echo_skb() during a hardware IRQ (which is often, but
not always, the case), the 'WARN_ON(in_irq)' in
net/core/skbuff.c#skb_release_head_state() might be triggered, under network
congestion circumstances, together with the potential risk of a NULL pointer
dereference.
The root cause of this issue is the call to kfree_skb() instead of
dev_kfree_skb_irq() in net/core/dev.c#enqueue_to_backlog().
This patch prevents the skb to be freed within the call to netif_rx() by
incrementing its reference count with skb_get(). The skb is finally freed by
one of the in-irq-context safe functions: dev_consume_skb_any() or
dev_kfree_skb_any(). The "any" version is used because some drivers might call
can_get_echo_skb() in a normal context.
The reason for this issue to occur is that initially, in the core network
stack, loopback skb were not supposed to be received in hardware IRQ context.
The CAN stack is an exeption.
This bug was previously reported back in 2017 in [1] but the proposed patch
never got accepted.
While [1] directly modifies net/core/dev.c, we try to propose here a
smoother modification local to CAN network stack (the assumption
behind is that only CAN devices are affected by this issue).
[1] http://lore.kernel.org/r/57a3ffb6-3309-3ad5-5a34-e93c3fe3614d@cetitec.com
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20201002154219.4887-2-mailhol.vincent@wanadoo.fr
Fixes: 39549eef35 ("can: CAN Network device driver and Netlink interface")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ad02c7f4f ]
This patch implements error handling and propagates the error value of
flexcan_chip_stop(). This function will be called from flexcan_suspend()
in an upcoming patch in some SoCs which support LPSR mode.
Add a new function flexcan_chip_stop_disable_on_error() that tries to
disable the chip even in case of errors.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
[mkl: introduce flexcan_chip_stop_disable_on_error() and use it in flexcan_close()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-11-mkl@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81f1f5ae8b ]
0704c57436 can: m_can_platform: remove unnecessary m_can_class_resume() call
removed the m_can_class_resume() call in the runtime resume path to get
rid of a infinite recursion, so the runtime resume now only handles the device
clocks.
Unfortunately it did not remove the complementary m_can_class_suspend() call in
the runtime suspend function, so those paths are now unbalanced, which causes
the pinctrl state to get stuck on the "sleep" state, which breaks all CAN
functionality on SoCs where this state is defined. Remove the
m_can_class_suspend() call to fix this.
Fixes: 0704c57436 can: m_can_platform: remove unnecessary m_can_class_resume() call
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20200811081545.19921-1-l.stach@pengutronix.de
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b9258a2cec ]
struct can_frame contains some padding which is not explicitly zeroed in
slc_bump. This uninitialized data will then be transmitted if the stack
initialization hardening feature is not enabled (CONFIG_INIT_STACK_ALL).
This commit just zeroes the whole struct including the padding.
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com>
Fixes: a1044e36e4 ("can: add slcan driver for serial/USB-serial CAN adapters")
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: security@kernel.org
Cc: wg@grandegger.com
Cc: mkl@pengutronix.de
Cc: davem@davemloft.net
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2091a3d42b ]
As the description before netdev_run_todo, we cannot call free_netdev
before rtnl_unlock, fix it by reorder the code.
This patch is a 1:1 copy of upstream slip.c commit f596c87005
("slip: not call free_netdev before rtnl_unlock in slip_open").
Reported-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab02ad6605 ]
Add missing attribute validation for IFLA_CAN_TERMINATION
to the netlink policy.
Fixes: 12a6075cab ("can: dev: add CAN interface termination API")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3083124e6 ]
It's a good idea to reset a ip-block/spi device before using it, this
patch will reset the device.
And a generic reset function if needed elsewhere.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ace17d568 ]
write_wakeup can happen in parallel with close/hangup where tty->disc_data
is set to NULL and the netdevice is freed thus also freeing
disc_data. write_wakeup accesses disc_data so we must prevent close from
freeing the netdev while write_wakeup has a non-NULL view of
tty->disc_data.
We also need to make sure that accesses to disc_data are atomic. Which can
all be done with RCU.
This problem was found by Syzkaller on SLCAN, but the same issue is
reproducible with the SLIP line discipline using an LTP test based on the
Syzkaller reproducer.
A fix which didn't use RCU was posted by Hillf Danton.
Fixes: 661f7fda21 ("slip: Fix deadlock in write_wakeup")
Fixes: a8e83b1753 ("slcan: Port write_wakeup deadlock fix from slip")
Reported-by: syzbot+017e491ae13c0068598a@syzkaller.appspotmail.com
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tyler Hall <tylerwhall@gmail.com>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: syzkaller@googlegroups.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d77bd61a2 upstream.
Under load, the RX side of the mscan driver can get stuck while TX still
works. Restarting the interface locks up the system. This behaviour
could be reproduced reliably on a MPC5121e based system.
The patch fixes the return value of the NAPI polling function (should be
the number of processed packets, not constant 1) and the condition under
which IRQs are enabled again after polling is finished.
With this patch, no more lockups were observed over a test period of ten
days.
Fixes: afa17a500a ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Florian Faber <faber@faberman.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3069ce620d upstream.
The m_can tries to detect if Non ISO Operation is available while in
standby mode, this function results in the following error:
| tcan4x5x spi2.0 (unnamed net_device) (uninitialized): Failed to init module
| tcan4x5x spi2.0: m_can device registered (irq=84, version=32)
| tcan4x5x spi2.0 can2: TCAN4X5X successfully initialized.
When the tcan device comes out of reset it goes in standby mode. The
m_can driver tries to access the control register but fails due to the
device being in standby mode.
So this patch will put the tcan device in normal mode before the m_can
driver does the initialization.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f361cd947 upstream.
Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5660493c63 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Cc: stable <stable@vger.kernel.org> # 4.19
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Christer Beskow <chbe@kvaser.com>
Cc: Nicklas Johansson <extnj@kvaser.com>
Cc: Martin Henriksson <mh@kvaser.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b7603d080f ]
The MCR[LPMACK] read-only bit indicates that FlexCAN is in a lower-power
mode (Disabled mode, Doze mode, Stop mode).
The CPU can poll this bit to know when FlexCAN has actually entered low
power mode. The low power enter/exit acknowledgment helper will reduce
code duplication for disabled mode, doze mode and stop mode.
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit da2311a638 upstream.
Uninitialized Kernel memory can leak to USB devices.
Fix this by using kzalloc() instead of kmalloc().
Signed-off-by: Xiaolong Huang <butterflyhuangxx@gmail.com>
Fixes: 7259124eac ("can: kvaser_usb: Split driver into kvaser_usb_core.c and kvaser_usb_leaf.c")
Cc: linux-stable <stable@vger.kernel.org> # >= v4.19
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 048e3a34a2 upstream.
Stop Mode is entered when Stop Mode is requested at chip level and
MCR[LPM_ACK] is asserted by the FlexCAN.
Double check with IP owner, the MCR[LPM_ACK] bit should be polled for
stop mode acknowledgment, not the acknowledgment from chip level which
is used to gate flexcan clocks.
This patch depends on:
b7603d080f ("can: flexcan: add low power enter/exit acknowledgment helper")
Fixes: 5f186c257f (can: flexcan: fix stop mode acknowledgment)
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e707180ae2 upstream.
When suspending, and there is still CAN traffic on the interfaces the
flexcan immediately wakes the platform again. As it should :-). But it
throws this error msg:
[ 3169.378661] PM: noirq suspend of devices failed
On the way down to suspend the interface that throws the error message
calls flexcan_suspend() but fails to call flexcan_noirq_suspend(). That
means flexcan_enter_stop_mode() is called, but on the way out of suspend
the driver only calls flexcan_resume() and skips flexcan_noirq_resume(),
thus it doesn't call flexcan_exit_stop_mode(). This leaves the flexcan
in stop mode, and with the current driver it can't recover from this
even with a soft reboot, it requires a hard reboot.
This patch fixes the deadlock when using self wakeup, by calling
flexcan_exit_stop_mode() from flexcan_resume() instead of
flexcan_noirq_resume().
This also fixes another issue: CAN frames are received out-of-order in
first IRQ handler run after wakeup.
The problem is that the wakeup latency from frame reception to the IRQ
handler (where the CAN frames are sorted by timestamp) is much bigger
than the time stamp counter wrap around time. This means it's
impossible to sort the CAN frames by timestamp.
The reason is that the controller exits stop mode during noirq resume,
which means it receives frames immediately, but interrupt handling is
still not possible.
So exit stop mode during resume stage instead of noirq resume fixes this
issue.
Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60552253e2 upstream.
According to section "8.3.8 RST Pin" in the datasheet we are required to
wait >700us after the device is reset.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ab79b06dd upstream.
CANFD2.0 core uses BRAM for storing acceptance filter ID(AFID) and MASK
(AFMASK)registers. So by default AFID and AFMASK registers contain random
data. Due to random data, we are not able to receive all CAN ids.
Initializing AFID and AFMASK registers with Zero before enabling
acceptance filter to receive all packets irrespective of ID and Mask.
Fixes: 0db9071353 ("can: xilinx: add can 2.0 support")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 870db5d101 upstream.
USB completion handlers are called in atomic context and must
specifically not allocate memory using GFP_KERNEL.
Fixes: 9f2d3eae88 ("can: ucan: add driver for Theobroma Systems UCAN devices")
Cc: stable <stable@vger.kernel.org> # 4.19
Cc: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Cc: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ebd796e24 upstream.
Slcan_open doesn't clean-up device which registration failed from the
slcan_devs device list. On next open this list is iterated and freed
device is accessed. Fix this by calling slc_free_netdev in error path.
Driver/net/can/slcan.c is derived from slip.c. Use-after-free error was
identified in slip_open by syzboz. Same bug is in slcan.c. Here is the
trace from the Syzbot slip report:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:634
__asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132
sl_sync drivers/net/slip/slip.c:725 [inline]
slip_open+0xecd/0x11b7 drivers/net/slip/slip.c:801
tty_ldisc_open.isra.0+0xa3/0x110 drivers/tty/tty_ldisc.c:469
tty_set_ldisc+0x30e/0x6b0 drivers/tty/tty_ldisc.c:596
tiocsetd drivers/tty/tty_io.c:2334 [inline]
tty_ioctl+0xe8d/0x14f0 drivers/tty/tty_io.c:2594
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0xdb6/0x13e0 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0xfa/0x760 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: ed50e1600b ("slcan: Fix memory leak in error path")
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Miller <davem@davemloft.net>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zhang Qilong