Move aliases from bcm-cygnus.dtsi back to individual .dts files. Also
clean up the chosen node to have the stdout-path using the proper alias
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The third compatible string "brcm,brcmnand" in bcm-cygnus.dtsi nand node
is incorrect, redundant and should be removed. "brcm,brcmnand" is meant to
be used by STB based Broadcom SoCs. All iProc based SoCs should use
"brcm,nand-iproc".
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch enables touchscreen support on bcm958300k and bcm958305k.
Touchscreen is connected to these boards through the bcm9hmidc daughter
card, and therefore also adding bcm9hmidc.dtsi that describes the
daughter card
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reorder all Cygnus peripherals based on base register addresses in
bcm-cygnus.dtsi
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Move all Cygnus peripherals to be under the "axi" bus node of type
"simple-bus"
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Put all Cygnus core components into "core" node of type "simple-bus" in
bcm-cygnus.dtsi
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Move aliases into bcm-cygnus.dtsi to avoid duplications in Cygnus dts
files
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable NAND support for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add PCIe device nodes in bcm-cygnus.dtsi but keep them disabled there.
Only enable them for bcm958300k where PCIe interfaces are populated
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This enables all 3 GPIO controllers including the ASIU GPIO, the
chipcommonG GPIO, and the ALWAYS-ON GPIO, for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This enables the IOMUX support for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add I2C device nodes and its properties in bcm-cygnus.dtsi but keep
them disabled there. Individual I2C devices can be enabled in board
specific dts file when I2C slave devices are enabled in the future
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
