The DC5LDO regulator supplies VDD-CPUS, which is for the embedded
controller in the A31 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have axp22x.dtsi describing common axp22x hardware, use
it and reference the nodes instead of declaring the whole tree.
Also drop the "always-on" from the vdd-gpu regulator, since we don't
support the GPU anyway.
And add a regulator reference for cpu0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
"dcdc1-supply" and "dcdc5-supply" have been dropped, as they are
internally connected and should not be represented in the device
tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The hummingbird A31 has 2 rtc devices available: one in the SoC,
and a pcf8563 external rtc on i2c2.
For some unknown reason, the onboard backup battery alone can not
supply enough power to the internal rtc. When external power is
removed, the internal rtc would reset. Hence we want to use the
external one by default.
Add aliases for the rtc devices with the external one as rtc0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.
Remove it from our DT, as suggested.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.
While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Hummingbird A31 has an AMPAK AP6210 WiFi+Bluetooth module. The
WiFi part is a BCM43362 IC connected to MMC1 in the A31 SoC via SDIO.
The IC also takes a power enable signal via GPIO. This is supported
with the new power sequencing bindings.
The WiFi module supports out-of-band interrupt signaling via GPIO,
but this is not enabled yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the AXP221 regulators. Only the ones directly used
on the board are added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Hummingbird A31 has an AXP221 PMIC hooked up to the
P2WI controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Hummingbird A31 has an AXP221 PMIC hooked up to the P2WI controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Using label references is preferred when override settings from the
included dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.
Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Replace the various raw GPIO flags by their definition in the common
dt-bindings header.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Hummingbird A31 board, the RTL8211E ethernet phy has its reset
line connect to a gpio pin, instead of floating like on other boards.
Add the stmmac properties for describing the reset gpio.
The reset delays were taken from the RTL8211E datasheet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds support for the A31 Hummingbird:
http://www.merrii.com/en/pla_d.asp?id=172
The Merrii A31 Hummingbird is a development board based on the
Allwinner A31 SoC with multiple USB ports through a USB hub chip,
a uSD slot, a 10/100/1000M ethernet port, an AP6210 WiFi/BT chip,
TV-in, HDMI, VGA, audio in/out ports, and LCD/CSI headers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: enable usbphy, ehci0, ohci0 for on-board usb hub;
add pcf8563 rtc node; add comments for i2c0 and mmc0 pull-ups;
correct ethernet phy address to 0x01; drop uart2 (BT chip has
no power) and uart3 (no device); use proper commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
