Set/invalidate physical addresses based on the configuration of the
display present control. This is relevant not only when the display
present control is modified, but also when the Vivid instance EDID is
set/cleared.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CEC adapters and controllers (handlers) are now set up as follows:
1. Allocate CEC adapters: setup of control handlers in next step
requires these adapters to be allocated.
2. Setup of control handlers: This must be done prior to registering
and exposing the adapters to user space to avoid a race condition.
3. Register CEC adapters: make them available to user space.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: PTR_ERR -> PTR_ERR_OR_ZERO]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds the following bitmask control:
-V4L2_CID_DV_RX_POWER_PRESENT
The RX_POWER_PRESENT bitmask is set based on the digital video timings
signal mode. This also removes 1/1 warnings for v4l2-compliance test on
vivid instance with HDMI input.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds the following bitmask controls:
-V4L2_CID_DV_TX_EDID_PRESENT
-V4L2_CID_DV_TX_HOTPLUG
-V4L2_CID_DV_TX_RXSENSE
The bitmasks are all set based on the custom vivid DISPLAY_PRESENT
control. This also removes 2/2 v4l2-compliance warnings for vivid
output device.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This will be used for HDMI-specific controls such as hotplug detection
and power present.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a custom control for selecting the presence of a display connected
to the active output. This control is part of an effort to implement
proper HDMI (dis)connect behavior for vivid.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make the following properties per-input:
-Standard Signal Mode
-Standard
These properties need to be per-input in order to implement proper HDMI
(dis)connect-behavior, where the signal mode will be used to signify
whether or not there is an inpute device connected.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make the following properties per-input
-DV Timings Signal Mode
-DV Timings
These properties need to be per-input in order to implement proper
HDMI (dis)connect-behavior, where the signal mode will be used to
signify whether or not there is an input device connected.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The tpf_min (1/100) and tpf_max (100/1) are used as the lowest and the
highest allowable value for the desired frame period in
vivid_vid_cap_s_parm().
But the comparison between these values is unnecessary because the compared
value is already chosen from webcam_intervals[] (from 1/60 to 1/1).
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The assigment of FB_VMODE_NONINTERLACE to var->vmode should be a
bit-wise or of FB_VMODE_NONINTERLACE instead of an assignment,
otherwise the previous clearing of the FB_VMODE_MASK bits of
var->vmode makes no sense and is redundant.
Addresses-Coverity: ("Unused value")
Fixes: ad4e02d508 ("[media] vivid: add a simple framebuffer device for overlay testing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support for multiplanar and singleplanar formats is mutually exclusive,
at least in practice. In our attempt to unify support for support for
mplane and !mplane in v4l, let's get rid of the
->vidioc_enum_fmt_{vid,out}_cap_mplane() hooks and call
->vidioc_enum_fmt_{vid,out}_cap() instead.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[hverkuil-cisco@xs4all.nl: fix typos: pirv -> priv and prov -> priv]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlzrJgUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1XAIAJajJpeKc9MVQipi
zWiI+WgHDg8gG/HnLKzP2Zp4MUjTCz30t0rnBbdo6AyK6LnPBL53yxg9q64XN7vI
p/h2ys+/DvqhIYSPWX6C++HYQT4Cb5ghxJABEIsztd3G4nfB9L2vgq9zKSNFusTD
UtfUxufciZPX515TuE4IqWMwS4Ut5daH7V3jjZunhPiayTFv64e1KbpKLLzHR0NR
DfFbrPcdp7VyCT/A5AKrqfqeB6O9dm/Fe4CsdsaKuzASCXJ6GUc/A7iZDndv/KA4
f5Xh7SGlQ2TfT1ud/aMfdw3AcMjqB8zgMJenovJ7UuHDfULBWNeAmMh/cTDwY9eY
Xgyvfm0=
=S8p9
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc2' into patchwork
Merge back from upstream into media tree, as there are some
patches merged upstream that has pontential of causing
conflicts (one actually rised a conflict already).
Linux 5.2-rc2
* tag 'v5.2-rc2': (377 commits)
Linux 5.2-rc2
random: fix soft lockup when trying to read from an uninitialized blocking pool
tracing: Silence GCC 9 array bounds warning
ext4: fix dcache lookup of !casefolded directories
locking/lock_events: Use this_cpu_add() when necessary
KVM: x86: fix return value for reserved EFER
tools/kvm_stat: fix fields filter for child events
KVM: selftests: Wrap vcpu_nested_state_get/set functions with x86 guard
kvm: selftests: aarch64: compile with warnings on
kvm: selftests: aarch64: fix default vm mode
kvm: selftests: aarch64: dirty_log_test: fix unaligned memslot size
KVM: s390: fix memory slot handling for KVM_SET_USER_MEMORY_REGION
KVM: x86/pmu: do not mask the value that is written to fixed PMUs
KVM: x86/pmu: mask the result of rdpmc according to the width of the counters
x86/kvm/pmu: Set AMD's virt PMU version to 1
KVM: x86: do not spam dmesg with VMCS/VMCB dumps
kvm: Check irqchip mode before assign irqfd
kvm: svm/avic: fix off-by-one in checking host APIC ID
KVM: selftests: do not blindly clobber registers in guest asm
KVM: selftests: Remove duplicated TEST_ASSERT in hyperv_cpuid.c
...
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzkaller reported crashes on kfree() called from
vivid_vid_cap_s_selection(). This looks like a simple typo, as
dev->bitmap_cap is allocated with vzalloc() throughout the file.
Fixes: ef834f7836 ("[media] vivid: add the video capture and output
parts")
Signed-off-by: Alexander Potapenko <glider@google.com>
Reported-by: Syzbot <syzbot+6c0effb5877f6b0344e2@syzkaller.appspotmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The strncpy() function is being deprecated upstream. Replace
it by the safer strscpy().
While here, replace a few occurences of strlcpy() that were
recently added to also use strscpy().
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Checkpatch wants to use 'help' instead of '---help---':
WARNING: prefer 'help' over '---help---' for new help texts
Let's change it globally at the media subsystem, as otherwise people
would keep using the old way.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When vivid is unloaded it used vfree to free dev->bitmap_out,
but it was actually allocated using kmalloc. Use vzalloc
instead, conform what vivid-vid-cap.c does.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Enable vivid to make use of the following formats:
V4L2_PIX_FMT_AYUV32
V4L2_PIX_FMT_XYUV32
V4L2_PIX_FMT_VUYA32
V4L2_PIX_FMT_VUYX32
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the media device registration fails, don't call media_device_unregister
since the device was never actually registered.
When removing the module also call media_device_cleanup() to avoid a memory leak.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To correctly set the size of the image in a plane, it's needed
to divide the height of image by the vertical down sampling factor.
This was only happening in vivid_try_fmt_vid_cap(), but now it
applied in others sizeimage calculations as well.
Signed-off-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The wrong size check was performed for output formats like NV24 which
set vfmt->buffers to 1, but vfmt->planes is 2. It was incorrectly
checking the payload size for plane 1, which doesn't exist.
Note: vfmt->buffers refers to the number of per-plane-buffers that
should be allocated. vfmt->planes refers to the number of planes
that make up an image. vfmt->planes may be > vfmt->buffers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Validate the field for an output buffer. This ensures that the
field is validated when the buffer is queued to a request, and
not when the request itself is queued, which is too late.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_compliance gave a warning for the S_PARM test for output streams:
warn: v4l2-test-formats.cpp(1235): S_PARM is supported for buftype 2, but not for ENUM_FRAMEINTERVALS
The reason is that vivid mapped s_parm for output streams to g_parm. But if
S_PARM doesn't actually change anything, then it shouldn't be enabled at all.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The video output sizeimage calculation did not take data_offset into account.
This can cause problems with video loopback or exporting output buffers for
use as dmabuf import buffers since the output buffer size is now too small.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It makes no sense to support the USERPTR memory model if the vivid instance was
configured as dma_contig. Disable it if this is the case.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwW4/oeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG2QMH/Rl6iMpTUX23tMHe
eXQzAOSvQXaWlFoX25j1Jvt8nhS7Uy8vkdpYTCOI/7DF0Jg4O/6uxcZkErlwWxb8
MW1rMgpfO+OpDLSLXAO2GKxaKI3ArqF2BcOQA2mji1/jR2VUTqmIvBoudn5d+GYz
19aCyfdzmVTC38G9sBhhcqJ10EkxLiHe2K74bf4JxVuSf2EnTI4LYt5xJPDoT0/C
6fOeUNwVhvv5a4svvzJmortq7x7BwyxBQArc7PbO0MPhabLU4wyFUOTRszgsGd76
o5JuOFwgdIIHlSSacGla6rKq10nmkwR07fHfRFFwbvrfBOEHsXOP2hvzMZX+FLBK
IXOzdtc=
=XlMc
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc7' into patchwork
Linux 4.20-rc7
* tag 'v4.20-rc7': (403 commits)
Linux 4.20-rc7
scripts/spdxcheck.py: always open files in binary mode
checkstack.pl: fix for aarch64
userfaultfd: check VM_MAYWRITE was set after verifying the uffd is registered
fs/iomap.c: get/put the page in iomap_page_create/release()
hugetlbfs: call VM_BUG_ON_PAGE earlier in free_huge_page()
memblock: annotate memblock_is_reserved() with __init_memblock
psi: fix reference to kernel commandline enable
arch/sh/include/asm/io.h: provide prototypes for PCI I/O mapping in asm/io.h
mm/sparse: add common helper to mark all memblocks present
mm: introduce common STRUCT_PAGE_MAX_SHIFT define
alpha: fix hang caused by the bootmem removal
XArray: Fix xa_alloc when id exceeds max
drm/vmwgfx: Protect from excessive execbuf kernel memory allocations v3
MAINTAINERS: Daniel for drm co-maintainer
drm/amdgpu: drop fclk/gfxclk ratio setting
IB/core: Fix oops in netdev_next_upper_dev_rcu()
dm thin: bump target version
drm/vmwgfx: remove redundant return ret statement
drm/i915: Flush GPU relocs harder for gen3
...
Simulate a more precise timestamp by calculating it based on the
current framerate.
Signed-off-by: Gabriel Francisco Mandaji <gfmandaji@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: replaced division by 2 with bit shift]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If start_streaming() fails and all queued buffers are returned to
vb2, then do not call v4l2_ctrl_request_complete(). Nothing happened
to the request and the state should remain as it was before
start_streaming was called.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a new vivid button control to inject an error into the
req_validate request callback.
This will help testing with v4l2-compliance.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reorganize code to fix two smatch warnings:
drivers/media/platform/vivid/vivid-core.c: drivers/media/platform/vivid/vivid-core.c:889 vivid_create_instance() warn: potentially one past the end of array
'dev->query_dv_timings_qmenu[dev->query_dv_timings_size]'
drivers/media/platform/vivid/vivid-core.c: drivers/media/platform/vivid/vivid-core.c:889 vivid_create_instance() warn: potentially one past the end of array
'dev->query_dv_timings_qmenu[dev->query_dv_timings_size]'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When vivid_update_format_cap() is called it should free any overlay
bitmap since the compose size will change.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+0cc8e3cc63ca373722c6@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If you create multiple vivid instances, each with their own media
device, then there was no way to tell them apart.
Fill in the bus_info so each instance has a unique bus_info string.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The capture DV timings capabilities allowed for a minimum width and
height of 0. So passing a timings struct with 0 values is allowed
and will later cause a division by zero.
Ensure that the width and height must be >= 16 to avoid this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+57c3d83d71187054d56f@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
kthread_run returns an error pointer, but elsewhere in the code
dev->kthread_vid_cap/out is checked against NULL.
If kthread_run returns an error, then set the pointer to NULL.
I chose this method over changing all kthread_vid_cap/out tests
elsewhere since this is more robust.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+53d5b2df0d9744411e2e@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now the equivalent of FRACT_CMP() is added in v4l2 common internal API
header.
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now vidioc_cropcap is only used to return the pixelaspect, so
rename it accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJb2F9AAAoJEAhfPr2O5OEVm5YP/Ak53aAEI1oJNequwdTYKc+/
2xWRpYWREa1g+x4MlqWO+szlPWbGXCUVwye8ii2N/xihLapsKVrLCr/dDd5khsvw
bDux33BzpU3Ug/ncQKD6ZZv4vVRzG8DMPcpkOwSs0OoboJns6AkHVGCugR32qZsH
3SH/r1aJce0oK1rrzgbYYZHTvaPshvY2IOLPKrtFmO+73iCVRhpSdWjFsY+q2Alp
+3Ho/06iQYB2i+enXrwoIKHAYoXArXYbxS2dhaNz+NURrOAytmgfMisvvt67heHx
IEilE0AcSjjlN/eyOxp+WCZrg9JLXVzZLX6ZnqqM2OEu1AS/XBultJBsGaN0hOiV
dir2enoHNNOStI40hNSdbumg9I0Txmag2jtpaGyaBnnGmGRJ/JIYegCPRVMLygAf
HHFHjR4fnRnqZrlh9OGAHaqc9RNlUgFVdlyqFtdyIah+aNeuij3o69mWM35QMLhw
/0dTXBUXw9aD1dEg1cZ6PdzLWJgDd7n1gIdfzzzzLnzmBwmmhqxW8+evu9qSAXsP
rnEZuE77HYKVfiacWMwpZK6+lT51STAE8ouo3N8fmaC+4RQmpq0dYXtR8RnlcSUD
hKpJ6UsIIb5A6xKX7ed8x6FxV14TEEaa042A4eclxsAFiqqkNfWSozqV0vfW5vCD
2lrsuN3knpfh7XDBSr0y
=V4X4
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull new experimental media request API from Mauro Carvalho Chehab:
"A new media request API
This API is needed to support device drivers that can dynamically
change their parameters for each new frame. The latest versions of
Google camera and codec HAL depends on such feature.
At this stage, it supports only stateless codecs.
It has been discussed for a long time (at least over the last 3-4
years), and we finally reached to something that seem to work.
This series contain both the API and core changes required to support
it and a new m2m decoder driver (cedrus).
As the current API is still experimental, the only real driver using
it (cedrus) was added at staging[1]. We intend to keep it there for a
while, in order to test the API. Only when we're sure that this API
works for other cases (like encoders), we'll move this driver out of
staging and set the API into a stone.
[1] We added support for the vivid virtual driver (used only for
testing) to it too, as it makes easier to test the API for the ones
that don't have the cedrus hardware"
* tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (53 commits)
media: dt-bindings: Document the Rockchip VPU bindings
media: platform: Add Cedrus VPU decoder driver
media: dt-bindings: media: Document bindings for the Cedrus VPU driver
media: v4l: Add definition for the Sunxi tiled NV12 format
media: v4l: Add definitions for MPEG-2 slice format and metadata
media: videobuf2-core: Rework and rename helper for request buffer count
media: v4l2-ctrls.c: initialize an error return code with zero
media: v4l2-compat-ioctl32.c: add missing documentation for a field
media: media-request: update documentation
media: media-request: EPERM -> EACCES/EBUSY
media: v4l2-ctrls: improve media_request_(un)lock_for_update
media: v4l2-ctrls: use media_request_(un)lock_for_access
media: media-request: add media_request_(un)lock_for_access
media: vb2: set reqbufs/create_bufs capabilities
media: videodev2.h: add new capabilities for buffer types
media: buffer.rst: only set V4L2_BUF_FLAG_REQUEST_FD for QBUF
media: v4l2-ctrls: return -EACCES if request wasn't completed
media: media-request: return -EINVAL for invalid request_fds
media: vivid: add request support
media: vivid: add mc
...
Support 640x480 as a frame size for video input devices of vivid.
Signed-off-by: Keiichi Watanabe <keiichiw@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
New 16-bit bayer options are available in tpg so enable them in vivid.
Signed-off-by: Bård Eirik Winther <bwinther@cisco.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CTA-861 standards have been updated to refer to opRGB instead
of AdobeRGB. The official standard is in fact named opRGB, so
switch to that.
The two old defines referring to ADOBERGB in the public API are
put under #ifndef __KERNEL__ and a comment mentions that they are
deprecated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Several CEC functions are actually specific for use with receivers,
i.e. they should be part of the V4L2 subsystem, not CEC.
These functions deal with validating and modifying EDIDs for (HDMI)
receivers, and they do not actually have anything to do with the CEC
subsystem and whether or not CEC is enabled. The problem was that if
the CEC_CORE config option was not set, then these functions would
become stubs, but that's not right: they should always be valid.
So replace the cec_ prefix by v4l2_ and move them to v4l2-dv-timings.c.
Update all drivers that call these accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The strcpy() function is being deprecated upstream. Replace
it by the safer strscpy().
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set the capabilities field of v4l2_requestbuffers and v4l2_create_buffers.
The various mapping modes were easy, but for signaling the request capability
a new 'supports_requests' bitfield was added to videobuf2-core.h (and set in
vim2m and vivid). Drivers have to set this bitfield for any queue where
requests are supported.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for requests to vivid.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the media_device to vivid. This is a prerequisite
for request support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a 'bool from_other_dev' argument: set to true if the two
handlers refer to different devices (e.g. it is true when
inheriting controls from a subdev into a main v4l2 bridge
driver).
This will be used later when implementing support for the
request API since we need to skip such controls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
0day kernel testing robot got the below dmesg and the first bad commit is
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git master
commit 3354b54f9f
[ 248.847809] BUG: unable to handle kernel paging request at ffffc90000393131
[ 248.848015] Call Trace:
[ 248.848015] ? vivid_dev_release+0xc0/0xc0
[ 248.848015] ? acpi_dev_pm_attach+0x27/0xd0
This reverts commit 3354b54f9f.
The vivid driver uses a complex logic to save one kalloc/kfree
allocation. That non-trivial way of allocating data causes
smatch to warn:
drivers/media/platform/vivid/vivid-core.c:869 vivid_create_instance() warn: potentially one past the end of array 'dev->query_dv_timings_qmenu[dev->query_dv_timings_size]'
drivers/media/platform/vivid/vivid-core.c:869 vivid_create_instance() warn: potentially one past the end of array 'dev->query_dv_timings_qmenu[dev->query_dv_timings_size]'
I also needed to read the code several times in order to understand
what it was desired there. It turns that the logic was right,
although confusing to read.
As it is doing allocations on a non-standard way, let's add some
documentation while shutting up the false positive.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
