A dma_addr_t is potentially smaller than a phys_addr_t on some archs.
Don't truncate the address when doing the pfn conversion.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Matthew Wilcox <willy@linux.intel.com>
[willy: fix pfn_t_to_phys as well]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
pfn_t_to_page() honors the flags in the pfn_t value to determine if a
pfn is backed by a page. However, vm_insert_mixed() was originally
written to use pfn_valid() to make this determination. To restore the
old/correct behavior, ignore the pfn_t flags in the !pfn_t_devmap() case
and fallback to trusting pfn_valid().
Fixes: 01c8f1c44b ("mm, dax, gpu: convert vm_insert_mixed to pfn_t")
Cc: Dave Hansen <dave@sr71.net>
Cc: David Airlie <airlied@linux.ie>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The imgpdc_wdt driver can be built on all architectures with
CONFIG_COMPILE_TEST, but fails if no other watchdog driver is
enabled:
drivers/watchdog/built-in.o: In function `pdc_wdt_remove':
imgpdc_wdt.c:(.text+0x74): undefined reference to `watchdog_unregister_device'
This adds the normal 'select WATCHDOG_CORE' that is needed to
ensure the driver always builds cleanly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This change was requested by arm-soc maintainer Kevin Hilman
because the X in TANGOX is a wildcard.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In function ‘usb_pcwd_probe’:
drivers/watchdog/pcwd_usb.c:611:12: warning: variable ‘maxp’ set but not
used [-Wunused-but-set-variable]
int pipe, maxp;
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
sp805 wdt asserts interrupt for the first expiry and
reloads the counter. If wdt interrupt is set and count
reaches zero then wdt reset event is generated. To get
wdt reset at 't' timeout the driver loads wdt counter
with 't/2'. A ping before time 't' *should* prevent
wdt reset. Currently if ping is done after 't/2' then
wdt interrupt condition gets set. On the next countdown
of loadval wdt reset event occurs eventhough wdt was
reloaded before the set timeout 't'.
This patch clears the interrupt condition on ping.
Signed-off-by: Sandeep Tripathy <tripathy@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The header specifies GPL version 2 only, so make the MODULE_LICENSE
string use the respective string for that.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Johan Hedberg says:
====================
pull request: bluetooth 2016-01-30
Here's a set of important Bluetooth fixes for the 4.5 kernel:
- Two fixes to 6LoWPAN code (one fixing a potential crash)
- Fix LE pairing with devices using both public and random addresses
- Fix allocation of dynamic LE PSM values
- Fix missing COMPATIBLE_IOCTL for UART line discipline
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid populating pagecache when the block device is in DAX mode.
Otherwise these page cache entries collide with the fsync/msync
implementation and break data durability guarantees.
Cc: Jan Kara <jack@suse.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dynamically enabling DAX requires that the page cache first be flushed
and invalidated. This must occur atomically with the change of DAX mode
otherwise we confuse the fsync/msync tracking and violate data
durability guarantees. Eliminate the possibilty of DAX-disabled to
DAX-enabled transitions for now and revisit this for the next cycle.
Cc: Jan Kara <jack@suse.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Similar to the file I/O path, re-direct all I/O to the DAX path for I/O
to a block-device special file. Both regular files and device special
files can use the common filp->f_mapping->host lookup to determing is
DAX is enabled.
Otherwise, we confuse the DAX code that does not expect to find live
data in the page cache:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 7676 at mm/filemap.c:217
__delete_from_page_cache+0x9f6/0xb60()
Modules linked in:
CPU: 0 PID: 7676 Comm: a.out Not tainted 4.4.0+ #276
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
00000000ffffffff ffff88006d3f7738 ffffffff82999e2d 0000000000000000
ffff8800620a0000 ffffffff86473d20 ffff88006d3f7778 ffffffff81352089
ffffffff81658d36 ffffffff86473d20 00000000000000d9 ffffea0000009d60
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff82999e2d>] dump_stack+0x6f/0xa2 lib/dump_stack.c:50
[<ffffffff81352089>] warn_slowpath_common+0xd9/0x140 kernel/panic.c:482
[<ffffffff813522b9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:515
[<ffffffff81658d36>] __delete_from_page_cache+0x9f6/0xb60 mm/filemap.c:217
[<ffffffff81658fb2>] delete_from_page_cache+0x112/0x200 mm/filemap.c:244
[<ffffffff818af369>] __dax_fault+0x859/0x1800 fs/dax.c:487
[<ffffffff8186f4f6>] blkdev_dax_fault+0x26/0x30 fs/block_dev.c:1730
[< inline >] wp_pfn_shared mm/memory.c:2208
[<ffffffff816e9145>] do_wp_page+0xc85/0x14f0 mm/memory.c:2307
[< inline >] handle_pte_fault mm/memory.c:3323
[< inline >] __handle_mm_fault mm/memory.c:3417
[<ffffffff816ecec3>] handle_mm_fault+0x2483/0x4640 mm/memory.c:3446
[<ffffffff8127eff6>] __do_page_fault+0x376/0x960 arch/x86/mm/fault.c:1238
[<ffffffff8127f738>] trace_do_page_fault+0xe8/0x420 arch/x86/mm/fault.c:1331
[<ffffffff812705c4>] do_async_page_fault+0x14/0xd0 arch/x86/kernel/kvm.c:264
[<ffffffff86338f78>] async_page_fault+0x28/0x30 arch/x86/entry/entry_64.S:986
[<ffffffff86336c36>] entry_SYSCALL_64_fastpath+0x16/0x7a
arch/x86/entry/entry_64.S:185
---[ end trace dae21e0f85f1f98c ]---
Fixes: 5a023cdba5 ("block: enable dax for raw block devices")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Kirill A. Shutemov <kirill@shutemov.name>
Suggested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jan Kara <jack@suse.cz>
Suggested-by: Matthew Wilcox <willy@linux.intel.com>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ade7753_spi_read_reg_16() will either successfully read a value
from SPI, or return a failure code without delivering data. However,
the ade7753_stop_device() and ade7753_reset() functions use the returned
data without checking for an error condition first. Gcc detects this
as a possible bug and warns about it:
drivers/staging/iio/meter/ade7753.c: In function 'ade7753_remove':
drivers/staging/iio/meter/ade7753.c:348:6: error: 'val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
val |= BIT(4); /* AD converters can be turned off */
^
drivers/staging/iio/meter/ade7753.c:345:6: note: 'val' was declared here
u16 val;
^
drivers/staging/iio/meter/ade7753.c: In function 'ade7753_probe':
drivers/staging/iio/meter/ade7753.c:222:6: error: 'val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
In both cases, we can avoids the warning by checking the return code
before using the data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
According to the datasheet, the resolusion of temperature sensor is
-5.35 counts/C. Temperature ADC is 472 counts at 25C.
(https://www.sparkfun.com/datasheets/Sensors/Pressure/MPL115A1.pdf
NOTE: This is older revision, but this information is removed from the
latest datasheet from nxp somehow)
Temp [C] = (Tadc - 472) / -5.35 + 25
= (Tadc - 605.750000) * -0.186915888
So the correct offset is -605.750000.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Not every arch has io memory.
While the driver has correct dependencies the select statement
will bypass the HAS_IOMEM dependency.
So, unbreak the build by rendering it into a real dependency.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In twl4030_bci_probe() there are some failure paths where we call
iio_channel_release() with a NULL pointer. (Apparently, that driver can
opperate without a valid channel pointer). Let's fix it by adding a
NULL check in iio_channel_release().
Fixes: 2202e1fc5a ('drivers: power: twl4030_charger: fix link problems when building as module')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
clk_prepare()/clk_unprepare() must not be called within atomic context.
This patch calls clk_prepare() once for all from atmel_aes_probe() and
clk_unprepare() from atmel_aes_remove().
Then calls of clk_prepare_enable()/clk_disable_unprepare() were replaced
by calls of clk_enable()/clk_disable().
Cc: stable@vger.kernel.org
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reported-by: Matthias Mayr <matthias.mayr@student.kit.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
hash_sendmsg/sendpage() need to wait for the completion
of crypto_ahash_init() otherwise it can cause panic.
Cc: stable@vger.kernel.org
Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
RFC 4015 section 3.4 says the TCP sender MUST refrain from
reversing the congestion control state when the ACK signals
congestion through the ECN-Echo flag. Currently we may not
always do that when prior_ssthresh is reset upon receiving
ACKs with ECE marks. This patch fixes that.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
self->ctrl_skb is protected by self->spinlock, we should not
access it out of the lock. Move the debugging printk inside.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to_vmem_altmap() needs to return valid results until
arch_remove_memory() completes. It also needs to be valid for any pfn
in a section regardless of whether that pfn maps to data. This escape
was a result of a bug in the unit test.
The signature of this bug is that free_pagetable() fails to retrieve a
vmem_altmap and goes off into the weeds:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff811d2629>] get_pfnblock_flags_mask+0x49/0x60
[..]
Call Trace:
[<ffffffff811d3477>] free_hot_cold_page+0x97/0x1d0
[<ffffffff811d367a>] __free_pages+0x2a/0x40
[<ffffffff8191e669>] free_pagetable+0x8c/0xd4
[<ffffffff8191ef4e>] remove_pagetable+0x37a/0x808
[<ffffffff8191b210>] vmemmap_free+0x10/0x20
Fixes: 4b94ffdc41 ("x86, mm: introduce vmem_altmap to augment vmemmap_populate()")
Cc: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Arnd Bergmann says:
====================
network driver fixes
This is an updated series of fixes for the network device drivers
that showed warnings in ARM randconfig.
Changes since v1 are:
dropped "net: macb: avoid uninitialized variables", already fixed in net-next
dropped "net: fddi/defxx: avoid warning about uninitialized variable
use", already fixed in net-next
added missing barriers in "net: moxart: use correct accessors for
DMA memory"
clarified "net: bgmac: clarify CONFIG_BCMA dependency" changelog
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_set_eeprom() function correctly initializes the 'start' variable,
but gcc generates a false warning:
drivers/net/ethernet/broadcom/tg3.c: In function 'tg3_set_eeprom':
drivers/net/ethernet/broadcom/tg3.c:12057:4: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
I have not come up with a way to restructure the code in a way that
avoids the warning without making it less readable, so this adds an
initialization for the declaration to shut up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nb8800_poll() function initializes the 'next' variable in the
loop looking for new input data. We know this will be called at
least once because 'budget' is a guaranteed to be a positive number
when we enter the function, but the compiler doesn't know that
and warns when the variable is used later:
drivers/net/ethernet/aurora/nb8800.c: In function 'nb8800_poll':
drivers/net/ethernet/aurora/nb8800.c:350:21: warning: 'next' may be used uninitialized in this function [-Wmaybe-uninitialized]
Changing the 'while() {}' loop to 'do {} while()' makes it obvious
to the compiler what is going on so it no longer warns.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PCI_MSI is disabled, we get warnings about unused functions
in the vxge driver:
drivers/net/ethernet/neterion/vxge/vxge-main.c:2121:13: warning: 'adaptive_coalesce_tx_interrupts' defined but not used [-Wunused-function]
drivers/net/ethernet/neterion/vxge/vxge-main.c:2149:13: warning: 'adaptive_coalesce_rx_interrupts' defined but not used [-Wunused-function]
We could add another #ifdef here, but it's nicer to avoid those warnings
for good by converting the existing #ifdef to if(IS_ENABLED()), which has
the same effect but provides better compile-time coverage in general,
and lets the compiler understand better when the function is intentionally
unused.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bgmac driver depends on BCMA_HOST_SOC, which is only used
when CONFIG_BCMA is enabled. However, it is a bool option and can
be set when CONFIG_BCMA=m, and then bgmac can be built-in, leading
to an obvious link error:
drivers/built-in.o: In function `bgmac_init':
:(.init.text+0x7f2c): undefined reference to `__bcma_driver_register'
drivers/built-in.o: In function `bgmac_exit':
:(.exit.text+0x110a): undefined reference to `bcma_driver_unregister'
To avoid this case, we need to depend on both BCMA and BCMA_SOC,
as this patch does. I'm also trying to make the dependency more
readable by splitting it into three lines, and adding a COMPILE_TEST
alternative so we can test-build it in all configurations that
support BCMA.
The added dependency on FIXED_PHY addresses a related issue where
we cannot call fixed_phy_register() when CONFIG_FIXED_PHY=m and
CONFIG_BGMAC=y.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building the hp100 ethernet driver causes warnings when both the PCI
and EISA drivers are disabled:
ethernet/hp/hp100.c: In function 'hp100_module_init':
ethernet/hp/hp100.c:3047:2: warning: label 'out3' defined but not used [-Wunused-label]
ethernet/hp/hp100.c: At top level:
ethernet/hp/hp100.c:2828:13: warning: 'cleanup_dev' defined but not used [-Wunused-function]
We can easily avoid the warnings and make the driver look slightly
nicer by removing the #ifdefs that check for the CONFIG_PCI and
CONFIG_EISA, as all the registration functions are designed to
have no effect when the buses are disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The davinci_cpdma mixes up physical addresses as seen from the CPU
and DMA addresses as seen from a DMA master, since it can operate
on both normal memory or an on-chip buffer. If dma_addr_t is
different from phys_addr_t, this means we get a compile-time warning
about the type mismatch:
ethernet/ti/davinci_cpdma.c: In function 'cpdma_desc_pool_create':
ethernet/ti/davinci_cpdma.c:182:48: error: passing argument 3 of 'dma_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
pool->cpumap = dma_alloc_coherent(dev, size, &pool->phys,
In file included from ethernet/ti/davinci_cpdma.c:21:0:
dma-mapping.h:398:21: note: expected 'dma_addr_t * {aka long long unsigned int *}' but argument is of type 'phys_addr_t * {aka unsigned int *}'
static inline void *dma_alloc_coherent(struct device *dev, size_t size,
This slightly restructures the code so the address we use for
mapping RAM into a DMA address is always a dma_addr_t, avoiding
the warning. The code is correct even if both types are 32-bit
because the DMA master in this device only supports 32-bit addressing
anyway, independent of the types that are used.
We still assign this value to pool->phys, and that is wrong if
the driver is ever used with an IOMMU, but that value appears to
be never used, so there is no problem really. I've added a couple
of comments about where we do things that are slightly violating
the API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni says:
====================
ipv6: fix sticky pktinfo behaviour
Currently:
ip addr add dev eth0 2001:0010::1/64
ip addr add dev eth1 2001:0020::1/64
ping6 -I eth0 2001:0020::2
do not lead to the expected results, i.e. eth1 is used as the
egress interface.
This is due to two related issues in handling sticky pktinfo,
used by ping6 to enforce the device binding:
- ip6_dst_lookup_flow()/ip6_dst_lookup_tail() do not really enforce
flowi6_oif match
- ipv6 udp connect() just ignore flowi6_oif
These patches address each issue individually.
The kernel has never enforced the egress interface specified
via the sticky pktinfo, except briefly between the commits
741a11d9e4 ("net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set")
and
d46a9d678e ("net: ipv6: Dont add RT6_LOOKUP_F_IFACE flag if saddr set"),
but the ping6 tools was unaffected up to iputils-20100214,
since before it used SO_BINDTODEVICE to enforce the egress
interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the egress interface index specified via IPV6_PKTINFO
is ignored by __ip6_datagram_connect(), so that RFC 3542 section 6.7
can be subverted when the user space application calls connect()
before sendmsg().
Fix it by initializing properly flowi6_oif in connect() before
performing the route lookup.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of ip6_dst_lookup_tail basically
ignore the egress ifindex match: if the saddr is set,
ip6_route_output() purposefully ignores flowi6_oif, due
to the commit d46a9d678e ("net: ipv6: Dont add RT6_LOOKUP_F_IFACE
flag if saddr set"), if the saddr is 'any' the first route lookup
in ip6_dst_lookup_tail fails, but upon failure a second lookup will
be performed with saddr set, thus ignoring the ifindex constraint.
This commit adds an output route lookup function variant, which
allows the caller to specify lookup flags, and modify
ip6_dst_lookup_tail() to enforce the ifindex match on the second
lookup via said helper.
ip6_route_output() becames now a static inline function build on
top of ip6_route_output_flags(); as a side effect, out-of-tree
modules need now a GPL license to access the output route lookup
functionality.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Fix support for 3168 device:
* NVM version
* firmware file name
* device IDs
* Fix a compilation warning in dvm calibration code
* Fix the TPC (reduced Tx Power) code. This fixes performance issues
* Add device IDs for 8265
rtx2x00
* fix monitor mode regression dating back to 4.1
brcmfmac
* fix sdio initialisation related crash
rtlwifi
* rtl8821ae: Fix 5G failure when EEPROM is incorrectly encoded
ath9k
* ignore eeprom magic mismatch on flash based devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWqyRLAAoJEG4XJFUm622bRiAH/2s3rRrFik3LUDMMJWbLDoNa
5ofIUlQnYPiUzLrStGrrZ93jcqG0rAGLovxEMR3cuWuVIV43RKq2vu+RE97fu8nM
j0NkWtD/g3mHYPGTkJ6ItXbs7t7ghhV+kFHcuZGPaikjEb3pTMGaA7sslzvptcWB
vzsKym/wxcZCanLqgsyMnbjiwnja8jXH/WFg3Otp+Ki0EDzBeaV9XNX9xZHMf/Nf
7I7ffSdMrHFZ/XrvMpLB15SVo9yH+tAFwrMS1WWnKJvUqO8kJZWFdLKM3DcShMTi
Tz6mwy7geVaXlAKKoi7MxJh4PGzQewRBHTMdPKORnuKFwRAlbgD8PGT8+RlKDOg=
=REf0
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-01-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi
* Fix support for 3168 device:
* NVM version
* firmware file name
* device IDs
* Fix a compilation warning in dvm calibration code
* Fix the TPC (reduced Tx Power) code. This fixes performance issues
* Add device IDs for 8265
rtx2x00
* fix monitor mode regression dating back to 4.1
brcmfmac
* fix sdio initialisation related crash
rtlwifi
* rtl8821ae: Fix 5G failure when EEPROM is incorrectly encoded
ath9k
* ignore eeprom magic mismatch on flash based devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not trim skb for mmaped socket since its buf size is fixed
and userspace will read as frame which data equals head. mmaped
socket will not call recvmsg, means max_recvmsg_len is 0,
skb_reserve was not called before commit: db65a3aaf2.
Fixes: db65a3aaf2 (netlink: Trim skb to alloc size to avoid MSG_TRUNC)
Signed-off-by: Ken-ichirou MATSUZAWA <chamas@h4.dion.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of all_zeros_mac is 6 byte, but eth_hash() will access the
8 byte, and KASan reported the below bug:
[ 8596.479031] BUG: KASan: out of bounds access in __vxlan_find_mac+0x24/0x100 at addr ffffffff841514c0
[ 8596.487647] Read of size 8 by task ip/52820
[ 8596.490818] Address belongs to variable all_zeros_mac+0x0/0x40
[ 8596.496051] CPU: 0 PID: 52820 Comm: ip Tainted: G WC 4.1.15 #1
[ 8596.503520] Hardware name: HP ProLiant DL380p Gen8, BIOS P70 02/10/2014
[ 8596.509365] ffffffff841514c0 ffff88007450f0b8 ffffffff822fa5e1 0000000000000032
[ 8596.516112] ffff88007450f150 ffff88007450f138 ffffffff812dd58c ffff88007450f1d8
[ 8596.522856] ffffffff81113b80 0000000000000282 0000000000000001 ffffffff8101ee4d
[ 8596.529599] Call Trace:
[ 8596.530858] [<ffffffff822fa5e1>] dump_stack+0x4f/0x7b
[ 8596.535080] [<ffffffff812dd58c>] kasan_report_error+0x3bc/0x3f0
[ 8596.540258] [<ffffffff81113b80>] ? __lock_acquire+0x90/0x2140
[ 8596.545245] [<ffffffff8101ee4d>] ? save_stack_trace+0x2d/0x80
[ 8596.550234] [<ffffffff812dda70>] kasan_report+0x40/0x50
[ 8596.554647] [<ffffffff81b211e4>] ? __vxlan_find_mac+0x24/0x100
[ 8596.559729] [<ffffffff812dc399>] __asan_load8+0x69/0xa0
[ 8596.564141] [<ffffffff81b211e4>] __vxlan_find_mac+0x24/0x100
[ 8596.569033] [<ffffffff81b2683d>] vxlan_fdb_create+0x9d/0x570
it can be fixed by enlarging the all_zeros_mac to 8 byte, although it is
harmless; eth_hash() will be called in other place with the memory which
is larger and equal to 8 byte.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the port based VLAN maps should be configured to allow every
port to egress frames on all other ports, except themselves.
The debugfs interface shows that they are misconfigured. For instance, a
7-port switch has the following content in the related register 0x06:
GLOBAL GLOBAL2 SERDES 0 1 2 3 4 5 6
...
6: 1fa4 1f0f 4 7f 7e 7d 7c 7b 7a 79
...
This means that port 3 is allowed to talk to port 2-6, but cannot talk
to ports 0 and 1. With this fix, port 3 can correctly talk to all ports
except 3 itself:
GLOBAL GLOBAL2 SERDES 0 1 2 3 4 5 6
...
6: 1fa4 1f0f 4 7e 7d 7b 77 6f 5f 3f
...
Fixes: ede8098d0f ("net: dsa: mv88e6xxx: bridges do not need an FID")
Reported-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib_table_lookup function had a shift by 32 that triggered a UBSAN
warning. This was due to the fact that I had placed the shift first and
then followed it with the check for the suffix length to ignore the
undefined behavior. If we reorder this so that we verify the suffix is
less than 32 before shifting the value we can avoid the issue.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The moxart ethernet driver confuses coherent DMA buffers with
MMIO registers.
moxart_ether.c: In function 'moxart_mac_setup_desc_ring':
moxart_ether.c:146:428: error: passing argument 1 of '__fswab32' makes integer from pointer without a cast [-Werror=int-conversion]
moxart_ether.c:74:39: warning: incorrect type in argument 3 (different address spaces)
moxart_ether.c:74:39: expected void *cpu_addr
moxart_ether.c:74:39: got void [noderef] <asn:2>*tx_desc_base
This leaves the basic logic alone and uses normal pointers for
the virtual address of the descriptor. As we cannot use readl/writel
to access them, we also introduce our own moxart_desc_read
moxart_desc_write helpers that perform the same endianess swap
as the original code, but without the address space conversion.
The barriers are made explicit here where needed: Even in the worst-case
scenario, we just have to use a rmb() after checking ownership so
we don't read any input data before we are sure it is value, and we
use wmb() before transferring ownership back to the device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PROC_FS, CONFIG_IP_PNP_BOOTP, CONFIG_IP_PNP_DHCP and
CONFIG_IP_PNP_RARP are all disabled, we get a warning about the
ic_proto_used variable being unused:
net/ipv4/ipconfig.c:146:12: error: 'ic_proto_used' defined but not used [-Werror=unused-variable]
This avoids the warning, by making the definition conditional on
whether a dynamic IP configuration protocol is configured. If not,
we know that the value is always zero, so we can optimize away the
variable and all code that depends on it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This path was missed when turning on the memmap in pmem support. Permit
'pmem' as a valid location for the map.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Michael Chan says:
====================
bnxt_en: Bug fixes.
3 small bug fix patches for net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ring index j is not wrapped properly at the end of the ring, causing
it to reference pointers past the end of the ring. For proper loop
termination and to access the ring properly, we need to increment j and
mask it before referencing the ring entry.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hardware counter is misleading as it counts dropped packets that
don't match the hardware filters for unicast/broadcast/multicast. We
will still report this counter in ethtool -S for diagnostics purposes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use completion ring for ring free response from firmware. The response
will be the last entry in the ring and we can free the ring after getting
the response. This will guarantee no spurious DMA to freed memory.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are cases where qdisc_dequeue_peeked can return NULL, and the result
is dereferenced later on in the function.
Similarly to the other qdisc dequeue functions, check whether the skb
pointer is NULL and if it is, goto out.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM fixes from Russell King:
"Just one fix for a -fstack-protector-strong problem from Kees Cook,
and adding the new copy_file_range syscall"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: wire up copy_file_range() syscall
ARM: 8500/1: fix atags_to_fdt with stack-protector-strong
- Wire up copy_file_range() syscall from Chandan Rajendra
- Simplify module TOC handling from Alan Modra
- Remove newly added extra definition of pmd_dirty from Stephen Rothwell
- Allow user space to map rtas_rmo_buf from Vasant Hegde
- Fix PE location code from Gavin Shan
- Remove PPMU_HAS_SSLOT flag for Power8 from Madhavan Srinivasan
- Fixup _HPAGE_CHG_MASK from Aneesh Kumar K.V
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KZ85
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Wire up copy_file_range() syscall from Chandan Rajendra
- Simplify module TOC handling from Alan Modra
- Remove newly added extra definition of pmd_dirty from Stephen Rothwell
- Allow user space to map rtas_rmo_buf from Vasant Hegde
- Fix PE location code from Gavin Shan
- Remove PPMU_HAS_SSLOT flag for Power8 from Madhavan Srinivasan
- Fixup _HPAGE_CHG_MASK from Aneesh Kumar K.V
* tag 'powerpc-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fixup _HPAGE_CHG_MASK
powerpc/perf: Remove PPMU_HAS_SSLOT flag for Power8
powerpc/eeh: Fix PE location code
powerpc/mm: Allow user space to map rtas_rmo_buf
powerpc: Remove newly added extra definition of pmd_dirty
powerpc: Simplify module TOC handling
powerpc: Wire up copy_file_range() syscall
