The ppgtt page directory lives in a snatched part of the gtt pte
range. Which naturally gets cleared on hibernate when we pull the
power. Suspend to ram (which is what I've tested) works because
despite the fact that this is a mmio region, it is actually back by
system ram.
Fix this by moving the page directory setup code to the ppgtt init
code (which gets called on resume).
This fixes hibernate on my ivb and snb.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Quoting the BSpec from time immemorial:
PIPEACONF, bits 28:27: Frame Start Delay (Debug)
Used to delay the frame start signal that is sent to the display planes.
Care must be taken to insure that there are enough lines during VBLANK
to support this setting.
An instance of the BIOS leaving these bits set was found in the wild,
where it caused our modesetting to go all squiffy and skewiff.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47271
Reported-and-tested-by: Eva Wang <evawang@linpus.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43012
Reported-and-tested-by: Carl Richell <carl@system76.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull virtio S3 support patches from Amit Shah:
"Turns out S3 is not different from S4 for virtio devices: the device
is assumed to be reset, so the host and guest state are to be assumed
to be out of sync upon resume. We handle the S4 case with exactly the
same scenario, so just point the suspend/resume routines to the
freeze/restore ones.
Once that is done, we also use the PM API's macro to initialise the
sleep functions.
A couple of cleanups are included: there's no need for special thaw
processing in the balloon driver, so that's addressed in patches 1 and
2.
Testing: both S3 and S4 support have been tested using these patches
using a similar method used earlier during S4 patch development: a
guest is started with virtio-blk as the only disk, a virtio network
card, a virtio-serial port and a virtio balloon device. Ping from
guest to host, dd /dev/zero to a file on the disk, and IO from the
host on the virtio-serial port, all at once, while exercising S4 and
S3 (separately) were tested. They all continue to work fine after
resume. virtio balloon values too were tested by inflating and
deflating the balloon."
Pulling from Amit, since Rusty is off getting married (and presumably
shaving people).
* 's3-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio-console:
virtio-pci: switch to PM ops macro to initialise PM functions
virtio-pci: S3 support
virtio-pci: drop restore_common()
virtio: drop thaw PM operation
virtio: balloon: Allow stats update after restore from S4
Pull second try at vfs part d#2 from Al Viro:
"Miklos' first series (with do_lookup() rewrite split into edible
chunks) + assorted bits and pieces.
The 'untangling of do_lookup()' series is is a splitup of what used to
be a monolithic patch from Miklos, so this series is basically "how do
I convince myself that his patch is correct (or find a hole in it)".
No holes found and I like the resulting cleanup, so in it went..."
Changes from try 1: Fix a boot problem with selinux, and commit messages
prettied up a bit.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (24 commits)
vfs: fix out-of-date dentry_unhash() comment
vfs: split __lookup_hash
untangling do_lookup() - take __lookup_hash()-calling case out of line.
untangling do_lookup() - switch to calling __lookup_hash()
untangling do_lookup() - merge d_alloc_and_lookup() callers
untangling do_lookup() - merge failure exits in !dentry case
untangling do_lookup() - massage !dentry case towards __lookup_hash()
untangling do_lookup() - get rid of need_reval in !dentry case
untangling do_lookup() - eliminate a loop.
untangling do_lookup() - expand the area under ->i_mutex
untangling do_lookup() - isolate !dentry stuff from the rest of it.
vfs: move MAY_EXEC check from __lookup_hash()
vfs: don't revalidate just looked up dentry
vfs: fix d_need_lookup/d_revalidate order in do_lookup
ext3: move headers to fs/ext3/
migrate ext2_fs.h guts to fs/ext2/ext2.h
new helper: ext2_image_size()
get rid of pointless includes of ext2_fs.h
ext2: No longer export ext2_fs.h to user space
mtdchar: kill persistently held vfsmount
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPdrIWAAoJEDeqqVYsXL0Mny4IAMTzXGOXCykpWhdIe2R8w0Ys
eIoTJhBKoQWnLTV8cOODtwmtZcoQLeXkZmizZiAJvX6O1tOgueg+W4AFa9grxXGI
O0d1bSb2ardzU7VZrZSY60Hd4bylMwn4Xv/0dRrQMwTJO0LEeGWsJPV2+2BuXwMB
lGCNB67oUBXgMOI1jUZQRwx/mBzQ3e/gINjnpZTNKHia7YkX/yVTFISq7htgfDN7
1wRGxymbHtVap3NbtUO96BUUndAiF5vom+4WNvaQUyPrCc6aoGWjv+J9DQXY/zgv
AYjujAluK396D6YncGFAWBzYOg9WFbq54v0PRUanjcTTAu5ILs2BxqWdhmnvl14=
=IH8T
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
... and mtdchar_notifier along with it; just have ->drop_inode() that
will unconditionally get evict them instead of dances on mtd device
removal and use simple_pin_fs() instead of kern_mount()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since 3.2.12 and 3.3, some systems are failing to boot with a BUG_ON.
Some other systems using the pata_jmicron driver fail to boot because no
disks are detected. Passing pcie_aspm=force on the kernel command line
works around it.
The cause: commit 4949be1682 ("PCI: ignore pre-1.1 ASPM quirking when
ASPM is disabled") changed the behaviour of pcie_aspm_sanity_check() to
always return 0 if aspm is disabled, in order to avoid cases where we
changed ASPM state on pre-PCIe 1.1 devices.
This skipped the secondary function of pcie_aspm_sanity_check which was
to avoid us enabling ASPM on devices that had non-PCIe children, causing
trouble later on. Move the aspm_disabled check so we continue to honour
that scenario.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=42979 and
http://bugs.debian.org/665420
Reported-by: Romain Francoise <romain@orebokech.com> # kernel panic
Reported-by: Chris Holland <bandidoirlandes@gmail.com> # disk detection trouble
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Tested-by: Hatem Masmoudi <hatem.masmoudi@gmail.com> # Dell Latitude E5520
Tested-by: janek <jan0x6c@gmail.com> # pata_jmicron with JMB362/JMB363
[jn: with more symptoms in log message]
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no difference in supporting S3 and S4 for virtio devices: the
vqs have to be re-created as the device has to be assumed to be reset at
restore-time. Since S4 already handles this situation, we can directly
use the same code and callbacks for S3 support.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
restore_common() was shared between restore and thaw callbacks. With
thaw gone, we don't need restore_common() anymore.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The thaw operation was used by the balloon driver, but after the last
commit there's no reason to have separate thaw and restore callbacks.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
There's no reason stats update after restore can't work. If a host
requested for stats, and before servicing the request, the guest entered
S4, upon restore, the stats request can still be processed and sent off
to the host.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
Pull ACPI & Power Management changes from Len Brown:
- ACPI 5.0 after-ripples, ACPICA/Linux divergence cleanup
- cpuidle evolving, more ARM use
- thermal sub-system evolving, ditto
- assorted other PM bits
Fix up conflicts in various cpuidle implementations due to ARM cpuidle
cleanups (ARM at91 self-refresh and cpu idle code rewritten into
"standby" in asm conflicting with the consolidation of cpuidle time
keeping), trivial SH include file context conflict and RCU tracing fixes
in generic code.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (77 commits)
ACPI throttling: fix endian bug in acpi_read_throttling_status()
Disable MCP limit exceeded messages from Intel IPS driver
ACPI video: Don't start video device until its associated input device has been allocated
ACPI video: Harden video bus adding.
ACPI: Add support for exposing BGRT data
ACPI: export acpi_kobj
ACPI: Fix logic for removing mappings in 'acpi_unmap'
CPER failed to handle generic error records with multiple sections
ACPI: Clean redundant codes in scan.c
ACPI: Fix unprotected smp_processor_id() in acpi_processor_cst_has_changed()
ACPI: consistently use should_use_kmap()
PNPACPI: Fix device ref leaking in acpi_pnp_match
ACPI: Fix use-after-free in acpi_map_lsapic
ACPI: processor_driver: add missing kfree
ACPI, APEI: Fix incorrect APEI register bit width check and usage
Update documentation for parameter *notrigger* in einj.txt
ACPI, APEI, EINJ, new parameter to control trigger action
ACPI, APEI, EINJ, limit the range of einj_param
ACPI, APEI, Fix ERST header length check
cpuidle: power_usage should be declared signed integer
...
- A quite complex ab8500 charger driver, submitted by
Arun Murthy @ ST-Ericsson;
- Summit Microelectronics SMB347 Battery Charger, submitted by
Bruce E. Robertson and Alan Cox @ Intel.
And that's all.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=Y8fe
-----END PGP SIGNATURE-----
Merge tag 'for-v3.4-rc1' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Various small bugfixes and enhancements, plus two new drivers:
- A quite complex ab8500 charger driver, submitted by Arun Murthy @
ST-Ericsson;
- Summit Microelectronics SMB347 Battery Charger, submitted by Bruce
E Robertson and Alan Cox @ Intel.
And that's all."
* tag 'for-v3.4-rc1' of git://git.infradead.org/battery-2.6: (36 commits)
max17042_battery: Clean up interrupt handling
Revert "max8998_charger: Include linux/module.h just once"
ab8500_fg: Fix some build warnings on x86_64
max17042_battery: Fix CHARGE_FULL representation.
max8998_charger: Include linux/module.h just once
power_supply: Convert i2c drivers to module_i2c_driver
lp8727_charger: Add MODULE_DEVICE_TABLE
charger-manager: Simplify charger_get_property(), get rid of a warning
charger-manager: Clean up for better readability
da9052-battery: Convert to use module_platform_driver
da9052-battery: Fix a memory leak when unload the module
da9052-battery: Add missing platform_set_drvdata
ab8500: Turn unneeded global symbols into local ones
ab8500_fg: Fix copy-paste error
ab8500_fg: Get rid of 'struct battery_type'
ab8500_fg: Get rid of 'struct v_to_cap'
ab8500_btemp: Get rid of 'enum adc_therm'
ab8500_charger: Convert to the new USB OTG calls
ab8500-btemp: AB8500 battery temperature driver
ab8500-fg: A8500 fuel gauge driver
...
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.
There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
drivers/acpi/acpica/hwsleep.c
Text conflict between:
2feec47d4c
(ACPICA: ACPI 5: Support for new FADT SleepStatus, SleepControl registers)
which removed #include "actables.h"
and
09f98a825a
(x86, acpi, tboot: Have a ACPI os prepare sleep instead of calling tboot_sleep.)
which removed #include <linux/tboot.h>
The resolution is to remove them both.
Signed-off-by: Len Brown <len.brown@intel.com>
Conflicts:
drivers/acpi/sleep.c
This was a text conflict between
a2ef5c4fd4
(ACPI: Move module parameter gts and bfs to sleep.c)
which added #include <linux/module.h>
and
b24e509885
(ACPI, PCI: Move acpi_dev_run_wake() to ACPI core)
which added #include <linux/pm_runtime.h>
The resolution was to take them both.
Signed-off-by: Len Brown <len.brown@intel.com>
Conflicts:
drivers/acpi/apei/apei-base.c
This was a conflict between
15afae6046
(CPI, APEI: Fix incorrect APEI register bit width check and usage)
and
653f4b538f
(ACPICA: Expand OSL memory read/write interfaces to 64 bits)
The former changed a parameter in the call to acpi_os_read_memory64()
and the later replaced all calls to acpi_os_read_memory64()
with calls to acpi_os_read_memory().
Signed-off-by: Len Brown <len.brown@intel.com>
Using a u64 here creates an endian bug. We store a u32 number in the
top byte which is a larger number than intended on big endian systems.
There is no reason to use a 64 bit data type here, I guess it was just
an oversight.
I removed the initialization to zero as well. It's needed with a u64
but with a u32, the variable gets initialized properly inside the call
to acpi_os_read_port().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On a system on the thermal limit these are quite noisy and flood the logs.
Better would be a counter anyways. But given that we don't even have
anything for normal throttling this doesn't seem to be urgent either.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Quoth Dmitry Torokhov:
In addition to bus notifier we do install device notifier explicitly
so it might fire up early. The easiest fox would be to move
acpi_video_bus_start_devices() after input_allocate_device() but
before input_register_device() - unregistered input devices can handle
input_event() calls just fine.
May fix crashes reported in:
https://bugzilla.kernel.org/show_bug.cgi?id=40672
Signed-off-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Len Brown <len.brown@intel.com>
It is always better to check return values, so add some new checks and
correct existing ones.
v2: Be consistent and don't mix errors from -E* and AE_* namespaces.
Signed-off-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI 5.0 adds the BGRT, a table that contains a pointer to the firmware
boot splash and associated metadata. This simple driver exposes it via
/sys/firmware/acpi in order to allow bootsplash applications to draw their
splash around the firmware image and reduce the number of jarring graphical
transitions during boot.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Drivers may wish to add entries to /sys/firmware/acpi, so export acpi_kobj
in order to let them do that.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure the removal of mappings uses the same logic that put the
mappings in place.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The function apei_estatus_print() and apei_estatus_check() forget to move ahead
the gdata pointer when dealing with multiple generic error data sections.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The acpi_processor_cst_has_changed() function is invoked from a
CPU_ONLINE or CPU_DEAD function, which might well execute on CPU 0
even though the CPU being hotplugged is some other CPU. In addition,
acpi_processor_cst_has_changed() invokes smp_processor_id() without
protection, resulting in splats when onlining CPUs.
This commit therefore changes the smp_processor_id() to pr->id, as is
used elsewhere in the code, for example, in acpi_processor_add().
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
... so that acpi_unmap()'s behavior gets in sync with acpi_map()'s.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Len Brown <len.brown@intel.com>
During testing pci root bus removal, found some root bus bridge is not freed.
If booting with pnpacpi=off, those hostbridge could be freed without problem.
It turns out that some devices reference are not released during acpi_pnp_match.
that match should not hold one device ref during every calling.
Add pu_device calling before returning.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
The function acpi_processor_add is stored in the ops.add field of a
acpi_driver structure. This function is then called in
acpi_bus_driver_init. On failure, this function clears the field
device->driver_data, but does not free its contents. Thus the free has to
be done by the add function. In acpi_processor_add, the corresponding
value is pr. This value is currently freed on failure before storing it in
device->driver_data, but not after. This free is added in the error
handling code at the end of the function. The per_cpu variable
processors is also cleared so that it does not refer to a dangling pointer.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The current code incorrectly assumes that
(1) the APEI register bit width is always 8, 16, 32, or 64 and
(2) the APEI register bit width is always equal to the APEI
register access width.
ERST serialization instructions entries such as:
[030h 0048 1] Action : 00 [Begin Write Operation]
[031h 0049 1] Instruction : 03 [Write Register Value]
[032h 0050 1] Flags (decoded below) : 01
Preserve Register Bits : 1
[033h 0051 1] Reserved : 00
[034h 0052 12] Register Region : [Generic Address Structure]
[034h 0052 1] Space ID : 00 [SystemMemory]
[035h 0053 1] Bit Width : 03
[036h 0054 1] Bit Offset : 00
[037h 0055 1] Encoded Access Width : 03 [DWord Access:32]
[038h 0056 8] Address : 000000007F2D7038
[040h 0064 8] Value : 0000000000000001
[048h 0072 8] Mask : 0000000000000007
break this assumption by yielding:
[Firmware Bug]: APEI: Invalid bit width in GAR [0x7f2d7038/3/0]
I have found no ACPI specification requirements corresponding
with the above assumptions. There is even a good example in
the Serialization Instruction Entries section (ACPI 4.0 section
17.4,1.2, ACPI 4.0a section 2.5.1.2, ACPI 5.0 section 18.5.1.2)
that mentions a serialization instruction with a bit range of
[6:2] which is 5 bits wide, _not_ 8, 16, 32, or 64 bits wide.
Compile and boot tested with 3.3.0-rc7 on a IBM HX5.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some APEI firmware implementation will access injected address
specified in param1 to trigger the error when injecting memory
error, which means if one SRAR error is injected, the crash
always happens because it is executed in kernel context. This
new parameter can disable trigger action and control is taken
over by the user. In this way, an SRAR error can happen in user
context instead of crashing the system. This function is highly
depended on BIOS implementation so please ensure you know the
BIOS trigger procedure before you enable this switch.
v2:
notrigger should be created together with param1/param2
Tested-by: Tony Luck <tony.luck@lintel.com>
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On the platforms with ACPI4.x support, parameter extension
is not always doable, which means only parameter extension
is enabled, einj_param can take effect.
v2->v1: stopping early in einj_get_parameter_address for einj_param
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes a trivial copy & paste error in ERST header length check.
It's just for future safety because sizeof(struct acpi_table_einj)
equals to sizeof(struct acpi_table_erst) with current ACPI5.0
specification. It applies to v3.3-rc6.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
power_usage is always assigned a negative value and should be declared
a signed integer
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently when a CPU is off-lined it enters either MWAIT-based idle or,
if MWAIT is not desired or supported, HLT-based idle (which places the
processor in C1 state). This patch allows processors without MWAIT
support to stay in states deeper than C1.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.15 (GNU/Linux)
iEYEABECAAYFAk91TL0ACgkQGkmNcg7/o7hEjwCgmuz6QQKkow7e5q0x7DR5Z2NH
1YoAn3TpODDmpaBiou26uMRPhcR6e1qC
=JCA0
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH updates from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (25 commits)
sh: Support I/O space swapping where needed.
sh: use set_current_blocked() and block_sigmask()
sh: no need to reset handler if SA_ONESHOT
sh: intc: Fix up section mismatch for intc_ack_data
sh: select ARCH_DISCARD_MEMBLOCK.
sh: Consolidate duplicate _32/_64 unistd definitions.
sh: ecovec: switch SDHI controllers to card polling
sh: Avoid exporting unimplemented syscalls.
sh: add platform_device for RSPI in setup-sh7757
SH: pci-sh7780: enable big-endian operation.
serial: sh-sci: fix a race of DMA submit_tx on transfer
sh: dma: Collect up CHCR of SH7763, SH7764, SH7780 and SH7785
sh: dma: Collect up CHCR of SH7723 and SH7730
sh/next: Fix build fail by asm/system.h in asm/bitops.h
arch/sh/drivers/dma/{dma-g2,dmabrg}.c: ensure arguments to request_irq and free_irq are compatible
sh: cpufreq: Wire up scaling_available_freqs support.
sh: cpufreq: notify about rate rounding fallback.
sh: cpufreq: Support CPU clock frequency table.
sh: cpufreq: struct device lookup from CPU topology.
sh: cpufreq: percpu struct clk accounting.
...
acpi_processor_install_hotplug_notify() registers processor objects to
receive ACPI CPU hotplug event notifications. This patch additionally
registers processor device objects (ACPI0007) to receive the notifications
as well.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Print physical address info in a style consistent with the %pR style used
elsewhere in the kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
An HP laptop (Pavilion G4-1016tx) has the following code in _TMP:
Store (\_SB.PCI0.LPCB.EC0.RTMP, Local0)
If (LGreaterEqual (Local0, S4TP))
{
Store (One, HTS4)
}
S4TP is initialised at 0 and not programmed further until either _HOT or
_CRT is called. If we evaluate _TMP before the trip points then HTS4 will
always be set, causing the firmware to generate a message on boot
complaining that the system shut down because of overheating. The simplest
solution is just to reverse the checking of trip points and _TMP in thermal
init.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_dev_run_wake() is a generic function which can be used by
other subsystem too. Rename it to acpi_pm_device_run_wake, to be
consistent with acpi_pm_device_sleep_wake.
Then move it to ACPI core.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If the state_count is not initialized for the device use
the driver's state count as the default. That will prevent
to add it manually in the cpuidle driver initialization
routine and will save us from duplicate line of code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Some C states of new CPU might be not good. One reason is BIOS might
configure them incorrectly. To help developers root cause it quickly, the
patch adds a new sysfs entry, so developers could disable specific C state
manually.
In addition, C state might have much impact on performance tuning, as it
takes much time to enter/exit C states, which might delay interrupt
processing. With the new debug option, developers could check if a deep C
state could impact performance and how much impact it could cause.
Also add this option in Documentation/cpuidle/sysfs.txt.
[akpm@linux-foundation.org: check kstrtol return value]
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Reviewed-by: Yanmin Zhang <yanmin_zhang@intel.com>
Reviewed-and-Tested-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Devices may share same list of power resources in _PR0, for example
Device(Dev0)
{
Name (_PR0, Package (0x01)
{
P0PR,
P1PR
})
}
Device(Dev1)
{
Name (_PR0, Package (0x01)
{
P0PR,
P1PR
}
}
Assume Dev0 and Dev1 were runtime suspended.
Then Dev0 is resumed first and it goes into D0 state.
But Dev1 is left in D0_Uninitialised state.
This is wrong. In this case, Dev1 must be resumed too.
In order to hand this case, each power resource maintains a list of
devices which relies on it.
When power resource is ON, it will check if the devices on its list
can be resumed. The device can only be resumed when all the power
resouces of its _PR0 are ON.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If a device has _PR3, it means the device supports D3_COLD.
Add the ability to validate and enter D3_COLD state in ACPI.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Repair a common problem with objects that are defined to return
a variable-length Package of sub-objects. If there is only one
sub-object, some BIOS code mistakenly simply declares the single
object instead of a Package with one sub-object. This function
attempts to repair this error by wrapping a Package object around
the original object, creating the correct and expected Package
with one sub-object.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
