Always useful to know just which connector was polled and had its
status updated.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 541cc96691.
Wei Yonjun reported this caused a regression against Intel VGA hotplug
on his G33 hw.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Prevents code that assumes that the encoder is active when asked to be
disabled from dying a horrible death.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In order to correctly report monitor connected status changes, the
previous monitor status must be recorded in the connector->status
value instead of being discarded.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When setting a new crtc configuration, force the DPMS state of all
connectors to ON. Otherwise, they'll be left at OFF and a future mode set
that disables the specified connector will not turn the connector off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DRI2 swap & sync implementation needs precise
vblank counts and precise timestamps corresponding
to those vblank counts. For conformance to the OpenML
OML_sync_control extension specification the DRM
timestamp associated with a vblank count should
correspond to the start of video scanout of the first
scanline of the video frame following the vblank
interval for that vblank count.
Therefore we need to carry around precise timestamps
for vblanks. Currently the DRM and KMS drivers generate
timestamps ad-hoc via do_gettimeofday() in some
places. The resulting timestamps are sometimes not
very precise due to interrupt handling delays, they
don't conform to OML_sync_control and some are wrong,
as they aren't taken synchronized to the vblank.
This patch implements support inside the drm core
for precise and robust timestamping. It consists
of the following interrelated pieces.
1. Vblank timestamp caching:
A per-crtc ringbuffer stores the most recent vblank
timestamps corresponding to vblank counts.
The ringbuffer can be read out lock-free via the
accessor function:
struct timeval timestamp;
vblankcount = drm_vblank_count_and_time(dev, crtcid, ×tamp).
The function returns the current vblank count and
the corresponding timestamp for start of video
scanout following the vblank interval. It can be
used anywhere between enclosing drm_vblank_get(dev, crtcid)
and drm_vblank_put(dev,crtcid) statements. It is used
inside the drmWaitVblank ioctl and in the vblank event
queueing and handling. It should be used by kms drivers for
timestamping of bufferswap completion.
The timestamp ringbuffer is reinitialized each time
vblank irq's get reenabled in drm_vblank_get()/
drm_update_vblank_count(). It is invalidated when
vblank irq's get disabled.
The ringbuffer is updated inside drm_handle_vblank()
at each vblank irq.
2. Calculation of precise vblank timestamps:
drm_get_last_vbltimestamp() is used to compute the
timestamp for the end of the most recent vblank (if
inside active scanout), or the expected end of the
current vblank interval (if called inside a vblank
interval). The function calls into a new optional kms
driver entry point dev->driver->get_vblank_timestamp()
which is supposed to provide the precise timestamp.
If a kms driver doesn't implement the entry point or
if the call fails, a simple do_gettimeofday() timestamp
is returned as crude approximation of the true vblank time.
A new drm module parameter drm.timestamp_precision_usec
allows to disable high precision timestamps (if set to
zero) or to specify the maximum acceptable error in
the timestamps in microseconds.
Kms drivers could implement their get_vblank_timestamp()
function in a gpu specific way, as long as returned
timestamps conform to OML_sync_control, e.g., by use
of gpu specific hardware timestamps.
Optionally, kms drivers can simply wrap and use the new
utility function drm_calc_vbltimestamp_from_scanoutpos().
This function calls a new optional kms driver function
dev->driver->get_scanout_position() which returns the
current horizontal and vertical video scanout position
of the crtc. The scanout position together with the
drm_display_timing of the current video mode is used
to calculate elapsed time relative to start of active scanout
for the current video frame. This elapsed time is subtracted
from the current do_gettimeofday() time to get the timestamp
corresponding to start of video scanout. Currently
non-interlaced, non-doublescan video modes, with or
without panel scaling are handled correctly. Interlaced/
doublescan modes are tbd in a future patch.
3. Filtering of redundant vblank irq's and removal of
some race-conditions in the vblank irq enable/disable path:
Some gpu's (e.g., Radeon R500/R600) send spurious vblank
irq's outside the vblank if vblank irq's get reenabled.
These get detected by use of the vblank timestamps and
filtered out to avoid miscounting of vblanks.
Some race-conditions between the vblank irq enable/disable
functions, the vblank irq handler and the gpu itself (updating
its hardware vblank counter in the "wrong" moment) are
fixed inside vblank_disable_and_save() and
drm_update_vblank_count() by use of the vblank timestamps and
a new spinlock dev->vblank_time_lock.
The time until vblank irq disable is now configurable via
a new drm module parameter drm.vblankoffdelay to allow
experimentation with timeouts that are much shorter than
the current 5 seconds and should allow longer vblank off
periods for better power savings.
Followup patches will use these new functions to
implement precise timestamping for the intel and radeon
kms drivers.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: Julien Cristau pointed out that @nondestructive results in
double-negatives and confusion when trying to interpret the parameter,
so use @force instead. Much easier to type as well. ;-)
And fix the miscompilation of vmgfx reported by Sedat Dilek.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Destructive load-detection is very expensive and due to failings
elsewhere can trigger system wide stalls of up to 600ms. A simple
first step to correcting this is not to invoke such an expensive
and destructive load-detection operation automatically.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16265
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise when disabling the output we switch to the new fb (which is
likely NULL) and skip the call to mode_set -- leaking driver private
state on the old_fb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I broke out my trusty i845 and found a new boot failure, which upon
inspection turned out to be a recursion within:
drm_helper_probe_single_connector_modes() -> drm_helper_hpd_irq_event()
-> intel_crt_detect() -> drm_helper_probe_single_connector_modes()
Calling drm_kms_helper_poll_enable() instead performs the desired
re-initialisation of the polling should the user have toggled the
parameter, without the recursive side-effect.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only fallback to a set of default modes on a connector iff that
connector is known to be connected. The issue occurs that with limited
hardware which cannot probe a connector and so reports the
connector status as unknown will then attempt to retrieve the modes for
it during drm_helper_probe_single_connector_modes(). Should that fail,
the helper then generates a default set which fools the fb_helper and
causes havoc with the console and beyond.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Polling for a VGA device on an old system can be quite expensive,
causing latencies on the order of 600ms. As we hold the mode mutex for
this time and also need the same mutex to move the cursor, we trigger a
user-visible stall.
The real solution would involve improving the granulatity of the
locking and so perhaps performing some of the probing not under the lock
or some other updates can be done under different locks. Also reducing the
cost of probing for a non-existent monitor would be worthwhile. However,
exposing a parameter to disable polling is a simple workaround in the
meantime.
In order to accommodate users turning polling on and off at runtime, the
polling is potentially re-enabled on every probe. This is coupled to
the user calling xrandr, which seems to be a vaild time to reset the
polling timeout since the information on the connection has just been
updated. (The presumption being that all connections are probed in a
single xrandr pass, which is currently valid.)
References:
Bug 29536 - 2.6.35 causes ~600ms latency every 10s
https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bug 16265 - Why is kslowd accumulating so much CPU time?
https://bugzilla.kernel.org/show_bug.cgi?id=16265
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (55 commits)
io-mapping: move asm include inside the config option
vgaarb: drop vga.h include
drm/radeon: Add probing of clocks from device-tree
drm/radeon: drop old and broken mesa warning
drm/radeon: Fix pci_map_page() error checking
drm: Remove count_lock for calling lastclose() after 58474713 (v2)
drm/radeon/kms: allow FG_ALPHA_VALUE on r5xx
drm/radeon/kms: another r6xx/r7xx CS checker fix
DRM: Replace kmalloc/memset combos with kzalloc
drm: expand gamma_set
drm/edid: Split mode lists out to their own header for readability
drm/edid: Rewrite mode parse to use the generic detailed block walk
drm/edid: Add detailed block walk for VTB extensions
drm/edid: Add detailed block walk for CEA extensions
drm: Remove unused fields from drm_display_info
drm: Use ENOENT consistently for the error return for an unmatched handle.
drm/radeon/kms: mark 3D power states as performance
drm: Only set DPMS once on the CRTC not after every encoder.
drm/radeon/kms: add additional quirk for Acer rv620 laptop
drm: Propagate error code from fb_create()
...
Fix up trivial conflicts in drivers/gpu/drm/drm_edid.c
Commit 991ea75c (drm: use workqueue instead of slow-work), which made
drm to use wq instead of slow-work, didn't account for the return
value difference between delayed_slow_work_enqueue() and
queue_delayed_work(). The former returns 0 on success and -errno on
failures while the latter never fails and only uses the return value
to indicate whether the work was already pending or not.
This misconversion triggered spurious error messages. Remove the now
unnecessary return value check and error message.
Markus: caught another incorrect conversion in drm_kms_helper_poll_enable()
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (55 commits)
workqueue: mark init_workqueues() as early_initcall()
workqueue: explain for_each_*cwq_cpu() iterators
fscache: fix build on !CONFIG_SYSCTL
slow-work: kill it
gfs2: use workqueue instead of slow-work
drm: use workqueue instead of slow-work
cifs: use workqueue instead of slow-work
fscache: drop references to slow-work
fscache: convert operation to use workqueue instead of slow-work
fscache: convert object to use workqueue instead of slow-work
workqueue: fix how cpu number is stored in work->data
workqueue: fix mayday_mask handling on UP
workqueue: fix build problem on !CONFIG_SMP
workqueue: fix locking in retry path of maybe_create_worker()
async: use workqueue for worker pool
workqueue: remove WQ_SINGLE_CPU and use WQ_UNBOUND instead
workqueue: implement unbound workqueue
workqueue: prepare for WQ_UNBOUND implementation
libata: take advantage of cmwq and remove concurrency limitations
workqueue: fix worker management invocation without pending works
...
Fixed up conflicts in fs/cifs/* as per Tejun. Other trivial conflicts in
include/linux/workqueue.h, kernel/trace/Kconfig and kernel/workqueue.c
Workqueue can now handle high concurrency. Convert drm_crtc_helper to
use system_nrt_wq instead of slow-work. The conversion is mostly
straight forward. One difference is that drm_helper_hpd_irq_event()
no longer blocks and can be called from any context.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Unify debug printing so it easier to track what's happening
while debugging.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Original behaviour will be preserved for drivers that don't implement
disable() hooks for an encoder.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
More explicit than dpms. Same as the encoder disable function.
Need this to explicity disconnect plls from crtcs for reuse when you
plls:crtcs ratio isn't 1:1.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This move to using the list of crtcs in the fb helper and cleans up the
whole picking code, now we store the crtc/connectors we want directly
into the modeset and we use the modeset directly to set the mode.
Fixes from James Simmons and Ben Skeggs.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The fbdev layer in the kms code should act like a consumer of the kms services and avoid having relying on information being store in the kms core structures in order for it to work.
This patch
a) removes the info pointer/psuedo palette from the core drm_framebuffer structure and moves it to the fbdev helper layer, it also removes the core drm keeping a list of kernel kms fbdevs.
b) migrated all the fb helper functions out of the crtc helper file into the fb helper file.
c) pushed the fb probing/hotplug control into the driver
d) makes the surface sizes into a structure for ease of passing
This changes the intel/radeon/nouveau drivers to use the new helper.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now the EDID property will be updated when the corresponding EDID can be
obtained from the external display device. But after the external device
is plugged-out, the EDID property is not updated. In such case we still
get the corresponding EDID property although it is already detected as
disconnected.
https://bugs.freedesktop.org/show_bug.cgi?id=26743
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
a patch from Roel was wrong, fix this properly, really
if the fb ptrs are different fb changed shuold be true.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Following drm info repeat 207 times during one hour, it's quite annoying
[ 1266.286747] [drm] TV-19: set mode NTSC 480i 0
Change from DRM_INFO to DRM_DEBUG
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Lots of ppl keep thinking this is an oops, it was just a warning for
me to see, just make it a printk now.
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the current DRM code, an output that has been powered off
from userspace will automatically power back on when resuming
from suspend. This patch fixes this behaviour.
Tested only with the Intel i915 driver on an Intel GM45 Express
chipset.
Signed-off-by: David John <davidjon@xenontk.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sometimes we will use a crtc for integerated LVDS, which is different with
that assigned by BIOS. If we want to get flicker-free transitions,
then we could read out the current state for it and set our current state
accordingly.
But it is true that if we aren't reading current state out, we do need
to turn everything off before modesetting. Otherwise the clocks can get very
angry and we get things worse than a flicker at boot.
In fact we also do the similar thing in UMS mode. We will disable all the
possible outputs/crtcs for the first modesetting.
So we disable all the possible outputs/crtcs before entering the KMS mode.
Before we configure connector/encoder/crtc, the function of
drm_helper_disable_unused_function can disable all the possible outputs/crtcs.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Rafal Milecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This matches the X server's fallback modes when using RANDR 1.2.
See also: http://bugzilla.redhat.com/538761
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If drivers don't init the fb helper on the connector, the cmdline
code won't work, but it shouldn't crash either.
Signed-off-by: Dave Airlie <airlied@redhat.com>
[note this requires an fb patch posted to linux-fbdev-devel already]
This uses the normal video= command line option to control the kms
output setup at boot time. It is used to override the autodetection
done by kms.
video= normally takes a framebuffer as the first parameter, in kms
it will take a connector name, DVI-I-1, or LVDS-1 etc. If no output
connector is specified the mode string will apply to all connectors.
The mode specification used will match down the probed modes, and if
no mode is found it will add a CVT mode that matches.
video=1024x768 - all connectors match a 1024x768 mode or add a CVT on
video=VGA-1:1024x768, VGA-1 connector gets mode only.
The same strings as used in current fb modedb.c are used, except I've
added three more letters, e, D, d, e = enable, D = enable Digital,
d = disable, which allow a connector to be forced into a certain state.
Signed-off-by: Dave Airlie <airlied@redhat.com>
When an output was disconnected, its mode list would remain. If you later
plugged into a sink with no EDID (projector, etc), you'd inherit the mode
list from the old sink, which is not what you want.
taken from Fedora kernel
Signed-off-by: Dave Airlie <airlied@redhat.com>
The new code adds modes in the helper, which makes more sense
I disliked the non-driver code adding modes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the default mode for every output device when there
is no mode for it.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For shared tv-out and VGA encoders, we really need to know if
the encoder is just being switched off temporarily in blanking
or if we are really disabling it hard.
Also we need to try harder to disconnect encoders from unused
connectors so we can share more efficently.
(shared encoders stuff is coming in radeon tv-out support)
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Previously the old encoder would be called during modeset and without a connector bad things happened.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- The previous system was not very transparent, nor flexible.
- This is needed to be able to fix a few bugs in the mechanism.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the debug info in generic drm mode by using DRM_DEBUG_KMS
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This was caught by Weiss. Also added some comments to the
fb_changed and mode_changed variables to explain what they do.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Tested-by: Thomas White <taw@bitwiz.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Making the drm_crtc.c code recognize the DPMS property and invoke the
connector->dpms function doesn't remove any capability from the driver while
reducing code duplication.
That just highlighted the problem with the existing DPMS functions which
could turn off the connector, but failed to turn off any relevant crtcs. The
new drm_helper_connector_dpms function manages all of that, using the
drm_helper-specific crtc and encoder dpms functions, automatically computing
the appropriate DPMS level for each object in the system.
This fixes the current troubles in the i915 driver which left PLLs, pipes
and planes running while in DPMS_OFF mode or even while they were unused.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We have a drm_set_config which takes a crtc/encoder/mode setup,
and checks it to see if it can shortcut and just do a base setup,
or whether a complete mode setting is required.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check whether the INTERLACE/DBLSCAN is supported by output device. If
not, the mode containing the flag of INTERLACE/DBLSCAN will be marked
as unsupported.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In some cases we may receive a mode config that has a different
CRTC<->encoder map that the current configuration. In that case, we
need to disable any re-routed encoders before setting the mode,
otherwise they may not pick up the new CRTC (if the output types are
incompatible for example).
Tested-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Check the error paths within intel_pipe_set_base() to first cleanup and
then report back the error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We need to skip the connectors with a NULL encoder to match the success
path and avoid an OOPS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
When mode setting is first initialized, the driver will call into
drm_helper_initial_config() to set up an initial output and framebuffer
configuration. This routine is responsible for probing the available
connectors, encoders, and crtcs, looking for modes and putting together
something reasonable (where reasonable is defined as "allows kernel
messages to be visible on as many displays as possible").
However, the code was a bit too aggressive in setting default modes when
none were found on a given connector. Even if some connectors had modes,
any connectors found lacking modes would have the default 800x600 mode added
to their mode list, which in some cases could cause problems later down the
line. In my case, the LVDS was perfectly available, but the initial config
code added 800x600 modes to both of the detected but unavailable HDMI
connectors (which are on my non-existent docking station). This ended up
preventing later code from setting a mode on my LVDS, which is bad.
This patch fixes that behavior by making the initial config code walk
through the connectors first, counting the available modes, before it decides
to add any default modes to a possibly connected output. It also fixes the
logic in drm_target_preferred() that was causing zeroed out modes to be set
as the preferred mode for a given connector, even if no modes were available.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This removes the requirement for user space to pin a buffer before
setting a mode that is backed by the pixels from that buffer.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The initially merged modesetting API has some uglies in it, this
cleans up the struct members and ioctl ordering for initial submission.
It also removes the unneeded hotplug infrastructure.
airlied:- I've pulled this patch in from git modesetting-gem tree.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add mode setting support to the DRM layer.
This is a fairly big chunk of work that allows DRM drivers to provide
full output control and configuration capabilities to userspace. It was
motivated by several factors:
- the fb layer's APIs aren't suited for anything but simple
configurations
- coordination between the fb layer, DRM layer, and various userspace
drivers is poor to non-existent (radeonfb excepted)
- user level mode setting drivers makes displaying panic & oops
messages more difficult
- suspend/resume of graphics state is possible in many more
configurations with kernel level support
This commit just adds the core DRM part of the mode setting APIs.
Driver specific commits using these new structure and APIs will follow.
Co-authors: Jesse Barnes <jbarnes@virtuousgeek.org>, Jakob Bornecrantz <jakob@tungstengraphics.com>
Contributors: Alan Hourihane <alanh@tungstengraphics.com>, Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
