Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
- Add the MFD bindings doc to MAINTAINERS
- New Drivers
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
- New Device Support
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
- New Functionality
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
- Fix-ups
- Clean-up defunct author emails; da9063, max14577
- Kconfig fixups; wm8350-i2c, as3722
- Constify; altera-a10sr, sm501
- Supply PCI IDs; intel-lpss-pci
- Improve clocking; qcom_rpm
- Fix IRQ probing; ucb1x00-core
- Ensure fault log is cleared; da9052
- Remove NO_IRQ check; ucb1x00-core
- Supply I2C properties; intel-lpss-acpi, intel-lpss-pci
- Non standard declaration; tps65217, max8997-irq
- Remove unused code; lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi
- Make non-modular; altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core,
- OF bindings; ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808,
axp20x, lp873x, exynos5433-lpass, act8945a,
aspeed-scu, twl6040, arizona
- Bug Fixes
- Release OF pointer; qcom_rpm
- Avoid double shifting in suspend/resume; 88pm80x
- Fix 'defined but not used' error; exynos-lpass
- Fix 'sleeping whilst attomic'; atmel-hlcdc
-----BEGIN PGP SIGNATURE-----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=Ja7p
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core framework:
- Add the MFD bindings doc to MAINTAINERS
New drivers:
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
New device support:
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
New functionality:
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
Fix-ups:
- Clean-up defunct author emails (da9063, max14577)
- Kconfig fixups (wm8350-i2c, as37220
- Constify (altera-a10sr, sm501)
- Supply PCI IDs (intel-lpss-pci)
- Improve clocking (qcom_rpm)
- Fix IRQ probing (ucb1x00-core)
- Ensure fault log is cleared (da9052)
- Remove NO_IRQ check (ucb1x00-core)
- Supply I2C properties (intel-lpss-acpi, intel-lpss-pci)
- Non standard declaration (tps65217, max8997-irq)
- Remove unused code (lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi)
- Make non-modular (altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core)
- OF bindings (ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808, axp20x,
lp873x, exynos5433-lpass, act8945a, aspeed-scu, twl6040, arizona)
Bugfixes:
- Release OF pointer (qcom_rpm)
- Avoid double shifting in suspend/resume (88pm80x)
- Fix 'defined but not used' error (exynos-lpass)
- Fix 'sleeping whilst attomic' (atmel-hlcdc)"
* tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: arizona: Handle probe deferral for reset GPIO
mfd: arizona: Remove arizona_of_get_named_gpio helper function
mfd: arizona: Add DT options for max_channels_clocked and PDM speaker config
mfd: twl6040: Register child device for twl6040-pdmclk
mfd: cros_ec_spi: Remove unused variable 'request'
mfd: omap-usb-host: Return value is not 'const int'
mfd: ab8500-debugfs: Remove 'weak' function suspend_test_wake_cause_interrupt_is_mine()
mfd: ab8500-debugfs: Remove ab8500_dump_all_banks_to_mem()
mfd: db8500-prcmu: Remove unused *prcmu_set_ddr_opp() calls
mfd: ab8500-debugfs: Prevent initialised field from being over-written
mfd: max8997-irq: 'inline' should be at the beginning of the declaration
mfd: rk808: Fix RK818_IRQ_DISCHG_ILIM initializer
mfd: tps65217: Fix nonstandard declaration
mfd: lp873x: Remove unused mutex lock from struct lp873x
mfd: atmel-hlcdc: Do not sleep in atomic context
mfd: exynos-lpass: Mark PM functions as __maybe_unused
mfd: intel-lpss: Add default I2C device properties for Apollo Lake
mfd: twl-core: Make it explicitly non-modular
mfd: sun6i-prcm: Make it explicitly non-modular
mfd: smsc-ece1099: Make it explicitly non-modular
...
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
Added one additional parameter to thermal_zone_device_update() to provide
caller with an optional capability to specify reason.
Currently this event is used by user space governor to trigger different
processing based on event code. Also it saves an additional call to read
temperature when the event is received.
The following events are cuurently defined:
- Unspecified event
- New temperature sample
- Trip point violated
- Trip point changed
- thermal device up and down
- thermal device power capability changed
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We get 2 warnings when building kernel with W=1:
drivers/regulator/dbx500-prcmu.c:78:6: warning: no previous prototype for 'ux500_regulator_suspend_debug' [-Wmissing-prototypes]
drivers/regulator/dbx500-prcmu.c:87:6: warning: no previous prototype for 'ux500_regulator_resume_debug' [-Wmissing-prototypes]
In fact, these functions are unused in
dbx500-prcmu.c, but should be removed.
So this patch removes the unused functions.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Three files are modified, the driver, header file and the binding document.
Updates for the regulator source file include and .of_match_table entry
and node match checking in the probe() function for a compatible pv88080
silicon type. A new "HVBUCK" is added in source file and added
regsiter definition in header file for pv88080 bb silicion.
The binding documentation changes have been made to reflect these updates.
Signed-off-by: Eric Jeong <eric.jeong.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drms_uA_update() always returns failure when it cannot find regulator's
input voltage. But if hardware supports load configuration with
ops->set_load() and the input regulator isn't specified with valid reason
such as the input regulator is battery, not finding input voltage is
normal so such case should not return with an error.
Avoid such inadequate error return by checking input/output voltages
only when drms_uA_update() is about to configure load with enum based
ops->set_mode().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
http://www.ti.com/lit/pdf/SWCZ010:
DCDC o/p voltage can go higher than programmed value
Impact:
VDDI, VDD2, and VIO output programmed voltage level can go higher than
expected or crash, when coming out of PFM to PWM mode or using DVFS.
Description:
When DCDC CLK SYNC bits are 11/01:
* VIO 3-MHz oscillator is the source clock of the digital core and input
clock of VDD1 and VDD2
* Turn-on of VDD1 and VDD2 HSD PFETis synchronized or at a constant
phase shift
* Current pulled though VCC1+VCC2 is Iload(VDD1) + Iload(VDD2)
* The 3 HSD PFET will be turned-on at the same time, causing the highest
possible switching noise on the application. This noise level depends
on the layout, the VBAT level, and the load current. The noise level
increases with improper layout.
When DCDC CLK SYNC bits are 00:
* VIO 3-MHz oscillator is the source clock of digital core
* VDD1 and VDD2 are running on their own 3-MHz oscillator
* Current pulled though VCC1+VCC2 average of Iload(VDD1) + Iload(VDD2)
* The switching noise of the 3 SMPS will be randomly spread over time,
causing lower overall switching noise.
Workaround:
Set DCDCCTRL_REG[1:0]= 00.
Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The new op is analogous to set_voltage_time_sel. It can be used by
regulators which don't have a table of discrete voltages. The function
returns the time for the regulator output voltage to stabilize after
being set to a new value, in microseconds. If the op is not set a
default implementation is used to calculate the delay.
This change also removes the ramp_delay calculation in the PWM
regulator, since the driver now uses the core code for the calculation
of the delay.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code assumes that only the ramp_delay is used to determine
the time needed for the voltage to stabilize. This may be true for the
calculation done by regulator_set_voltage_time_sel(), however regulators
can implement their own set_voltage_time_sel() op which would be skipped
if no ramp delay is specified. Remove the check in
_regulator_do_set_voltage(), the functions calculating the ramp delay
return 0 anyway when the ramp delay is not configured.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the voltage can not be set jump to the end of the function. This
avoids having to check for an error multiple times and eliminates one
level of nesting in a follow-up change.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
also a switch. The buck regulators support teaming into multi-phase
groups, with A+B, A+B+C, D+E groupings.
Some registers controlling DCDC converter work settings are at different
offsets. Deal with them as well.
Add support for this new variant.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We get 1 warning when building kernel with W=1:
drivers/regulator/hi6421-regulator.c:480:14: warning: no previous prototype for
'hi6421_regulator_ldo_get_optimum_mode' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
So this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the rk818 regulator. The regulator module consists
of 4 DCDCs, 9 LDOs, 1 switch and 1 BOOST converter which is used to
power OTG and HDMI5V.
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change the MFD config option as per latest naming
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In order to support the Qualcomm MDM9615 SoC, add support for the
PM8018 RPM regulator in the qcom_rpm-regulator driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix typo in regulator Kconfig for the TPS80031 tristate string (trivial)
Signed-off-by: Sebastiaan Schalbroeck <schalbroeck@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch was based on my missinterpretation of the API and only
accidentally worked for me. Let's clean it out to not confuse others.
This reverts commit 3ff3f518a1.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Linear Technology LTC3676
8-output I2C voltage regulator IC.
Cc: Jaffer Kapasi <jkapasi@linear.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some versions of tps65218 do not seem to support poweroff modes properly
if DCDC3 regulator is shut-down. Thus, keep it enabled even during
poweroff if the version info matches the broken silicon revision.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom iProc,
STMPE and ChromeOS EC controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TdEI
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom
iProc, STMPE and ChromeOS EC controllers"
* tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
regulator: pwm: Document pwm-dutycycle-unit and pwm-dutycycle-range
regulator: pwm: Support extra continuous mode cases
pwm: Add ChromeOS EC PWM driver
dt-bindings: pwm: Add binding for ChromeOS EC PWM
mfd: cros_ec: Add EC_PWM function definitions
mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
pwm: atmel: Use of_device_get_match_data()
pwm: atmel: Fix checkpatch warnings
pwm: atmel: Fix disabling of PWM channels
dt-bindings: pwm: Add R-Car H3 device tree bindings
pwm: rcar: Use ARCH_RENESAS
pwm: tegra: Add support for Tegra186
dt-bindings: pwm: tegra: Add compatible string for Tegra186
pwm: tegra: Avoid overflow when calculating duty cycle
pwm: tegra: Allow 100 % duty cycle
pwm: tegra: Add support for reset control
pwm: tegra: Rename mmio_base to regs
pwm: tegra: Remove useless padding
pwm: tegra: Drop NUM_PWM macro
pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value
...
The voltage ranges listed here are wrong. The pma8084 pldo
supports three different overlapping voltage ranges with
differing step sizes and the pma8084 ftsmps supports two. These
ranges can be seen in the "native" spmi regulator driver
(qcom_spmi-regulator.c) at pldo_ranges[] and ftsmps_ranges[]
respectively. Port these ranges over to the RPM SMD regulator
driver so that we list the appropriate set of supported voltages
on these types of regulators.
Fixes: ee01d0c91e ("regulator: qcom-smd: Add support for PMA8084")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The voltage ranges listed here are wrong. The correct ranges can
be seen in the "native" spmi regulator driver
qcom_spmi-regulator.c at pldo_ranges[], ftsmps_ranges[] and
boost_ranges[] for the pldo, ftsmps, and boost type regulators.
Port these ranges over to the RPM SMD regulator driver so that we
list the appropriate set of supported voltages on pldos.
Doing this allows us to specify a voltage like 3075000 for l24,
whereas before that wasn't a supported voltage.
Fixes: da65e367b6 ("regulator: Regulator driver for the Qualcomm RPM")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
The continuous mode allows one to declare a PWM regulator without having
to declare the voltage <-> dutycycle association table. It works fine as
long as your voltage(dutycycle) function is linear, but also has the
following constraints:
- dutycycle for min_uV = 0%
- dutycycle for max_uV = 100%
- dutycycle for min_uV < dutycycle for max_uV
While the linearity constraint is acceptable for now, we sometimes need to
restrict of the PWM range (to limit the maximum/minimum voltage for
example) or have a min_uV_dutycycle > max_uV_dutycycle (this could be
tweaked with PWM polarity, but not all PWMs support inverted polarity).
Add the pwm-dutycycle-range and pwm-dutycycle-unit DT properties to define
such constraints. If those properties are not defined, the PWM regulator
use the default pwm-dutycycle-range = <0 100> and
pwm-dutycycle-unit = <100> values (existing behavior).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This fix alters the minimum and maximum BUCK voltage limits for DA9052 and
DA9053. It does so for the following cases:
DA9052
- BUCK3 (MEM)
min: 0.925V -> 0.950V
max: 2.500V -> 2.525V
DA9053
- BUCK3 (MEM)
min: 0.925V -> 0.950V
max: 2.500V -> 2.525V
- BUCK4 (PERI)
min: 0.925V -> 0.950V
max: 2.500V -> 2.525V
The voltage range remains the same, but the limits are shifted by +0.025V.
This change is provided on DA9052:MEM, DA9053:MEM and DA9053:PERI
and is a voltage difference of 0.025V, compared to those measured before
this fix is applied. The patch has the effect of decreasing *all* measured
voltages on those BUCKs when compared against the previously measured
values for the same software voltage request.
For example, with this fix applied for DA9052:MEM, DA9053:MEM and
DA9053:PERI, the following is true.
Because the previous software defined slot 0 as being 0.925V, if a request
for 0.950V was previously sent, the slot 1 voltage would have been used.
This would have corresponded to an actual measured voltage of 0.975V. But,
with this patch fix, and with slot 0 properly aligned to 0.950V, if a
voltage of 0.950V is requested by software, a measured value of 0.950V will
be provided.
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MT6323 is a regulator found on boards based on MediaTek MT7623 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Addition of device tree support for DA9210.
Two files are modified, the driver source file and the binding document.
Updates for the regulator source file include an .of_match_table entry and
node match checking in the probe() function for a compatible da9210 string.
Minor binding documentation changes have been made to the title and the
example.
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This node pointer is returned by of_get_child_by_name() with
refcount incremented in this function. of_node_put() is missing
when exitting this function while invalid device type. Fix it
by move of_get_child_by_name() code after device type check.
Found by Coccinelle.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is only one instance of ab8500_regulator_platform_data, and it's
safe to assume we won't ever merge another one, so it's rather pointless
to pass it through multiple levels of platform data pointers.
This moves the structure and everything referenced by it into the
driver that uses it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pm8x41_hfsmps ranges overlap. The first range is from 375000
to 1562500:
375000 + (95 * 12500) == 1562500
and the second range starts at 1550000. Interestingly, the second
range ends at the correct value when it's set to be the
appropriate start value, 1575000:
1575000 + ((158 - 96) * 25000) == 3125000
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes some of the LDOs and BUCKs voltage range as per
user manual of s2mps15 (REV0.4).
Fixes: 51af206758 ("regulator: s2mps11: Add support for S2MPS15 regulators")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The continuous PWM voltage regulator is caching the voltage value in
the ->volt_uV field. While most of the time this value should reflect the
real voltage, sometime it can be sightly different if the PWM device
rounded the set_duty_cycle request.
Moreover, this value is not valid until someone has modified the regulator
output.
Remove the ->volt_uV field and always rely on the PWM state to calculate
the regulator output.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Linus Torvalds