Including (in no particular order):
- Page table code for AMD IOMMU now supports large pages where
smaller page-sizes were mapped before. VFIO had to work around
that in the past and I included a patch to remove it (acked by
Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would
never work as modules anyway.
- Work to unify the the iommu-related pointers in
'struct device' into one pointer. This work is not finished
yet, but will probably be in the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DT9A
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
Use Use device_iommu_mapped() to check if the device is
already mapped by an IOMMU.
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Renesas R-Mobile APE6 support is currently unused:
- DMA slaves were never enabled in r8a73a4.dtsi,
- The driver relies on legacy filter matching and describing all
slaves and MID/RIDs in a table, unlike modern DMA engine drivers for
similar hardware like rcar-dmac,
- The driver doesn't seem to work well.
Remove the driver, it can be resurrected from git history when needed.
As this was the last user of SH_DMAE_BASE on Renesas ARM SoCs, the
sh-dma-engine driver core is now used on SuperH only.
Note that the DT bindings are still present, as r8a73a4.dtsi uses them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix warning when running with CONFIG_DMA_API_DEBUG_SG=y by allocating a
device_dma_parameters structure and filling in the max segment size.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
rcar_dmac_chan_get_residue() should not stop the DMAC, because
the commit 538603c602 ("dmaengine: sh: rcar-dmac: avoid to write
CHCR.TE to 1 if TCR is set to 0") had fixed unexpected re-transferring
issue. But it had caused the next issue which might stop the cyclic
mode transferring. Thus, for example R-Car sound might be stopped
suddenly.
According to the commit 73a47bd0da ("dmaengine: rcar-dmac: use TCRB
instead of TCR for residue"), the purpose of clearing CHCR.DE bit is
flushing buffered data to calculate the exact residue.
Such the "exact" residue had been required by sh-sci driver. sh-sci
driver is calling dmaengine_pause() to stop transferring, and get
"exact" residue. Otherwise, it might receive extra data during
getting residue without pausing.
In rx_timer_fn() of sh-sci driver:
dmaengine_tx_status(); /* For checking roughly */
dmaengine_pause();
dmaengine_tx_status(); /* For getting residue */
dmaengine_terminate_all();
But, unfortunately the rcar-dmac driver didn't support dmaengine_pause()
at that time. So, the sh-sci driver cannot get the "exact" residue
without stopping the transferring, because rcar-dmac is buffering data
inside.
Because of these backgrounds, rcar-dmac had been cleared/set CHCR.DE
bit in rcar_dmac_chan_get_residue() to synchronizing data and getting
"exact" residue.
However, rcar-dmac driver has rcar_dmac_chan_pause() now, and clearing
CHCR.DE bit in rcar_dmac_chan_get_residue() doesn't need anymore.
So, this patch removes the rcar_dmac_sync_tcr().
Fixes: 73a47bd0da ("dmaengine: rcar-dmac: use TCRB instead of TCR for residue")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds dma_pause operation. This patch is based on
Muhammad Hamza Farooq's patch.
After this patch applied, an issue that the sh-sci driver with
high baud rate might cause data lost disappeared because the DMAC
is possible to transmit between [1] and [2] below, and then
the residue of [1] is not true:
In rx_timer_fn() of the sh-sci.c:
dmaengine_pause();
...
dmaengine_tx_status(); /* [1] */
...
dmaengine_terminate_all(); /* [2] */
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds a new function rcar_dmac_clear_chcr_de() to simplify
adding pause function later.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch fixes an issue that unexpected retransfering happens
if TCR is set to 0 before rcar_dmac_sync_tcr() writes DE bit to
the CHCR register. For example, sh-sci driver can reproduce this
issue like below:
In rx_timer_fn(): /* CHCR DE bit may be set to 1 */
dmaengine_tx_status()
rcar_dmac_tx_status()
rcar_dmac_chan_get_residue()
rcar_dmac_sync_tcr() /* TCR is possible to be set to 0 */
According to the description of commit 73a47bd0da ("dmaengine:
rcar-dmac: use TCRB instead of TCR for residue"), "this buffered data
will be transferred if CHCR::DE bit was cleared". So, this patch
doesn't need to check TCRB register.
Fixes: 73a47bd0da ("dmaengine: rcar-dmac: use TCRB instead of TCR for residue")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We need to clear channel register in error case as recovery.
The channel is already stopped in such case, thus we don't need to call
rcar_dmac_chan_halt() before clearing.
rcar_dmac_chan_halt() will clear and confirm DE bit.
But it will be failed because channel is already stopped in error case.
In other words, we shouldn't call it then.
Reported-by: Hiroki Negishi <hiroki.negishi.bx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Hiroki Negishi <hiroki.negishi.bx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
During system reboot or halt, with lockdep enabled:
================================
WARNING: inconsistent lock state
4.18.0-rc1-salvator-x-00002-g9203dbec90a68103 #41 Tainted: G W
--------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
reboot/2779 [HC0[0]:SC0[0]:HE1:SE1] takes:
0000000098ae4ad3 (&(&rchan->lock)->rlock){?.-.}, at: rcar_dmac_shutdown+0x58/0x6c
{IN-HARDIRQ-W} state was registered at:
lock_acquire+0x208/0x238
_raw_spin_lock+0x40/0x54
rcar_dmac_isr_channel+0x28/0x200
__handle_irq_event_percpu+0x1c0/0x3c8
handle_irq_event_percpu+0x34/0x88
handle_irq_event+0x48/0x78
handle_fasteoi_irq+0xc4/0x12c
generic_handle_irq+0x18/0x2c
__handle_domain_irq+0xa8/0xac
gic_handle_irq+0x78/0xbc
el1_irq+0xec/0x1c0
arch_cpu_idle+0xe8/0x1bc
default_idle_call+0x2c/0x30
do_idle+0x144/0x234
cpu_startup_entry+0x20/0x24
rest_init+0x27c/0x290
start_kernel+0x430/0x45c
irq event stamp: 12177
hardirqs last enabled at (12177): [<ffffff800881d804>] _raw_spin_unlock_irq+0x2c/0x4c
hardirqs last disabled at (12176): [<ffffff800881d638>] _raw_spin_lock_irq+0x1c/0x60
softirqs last enabled at (11948): [<ffffff8008081da8>] __do_softirq+0x160/0x4ec
softirqs last disabled at (11935): [<ffffff80080ec948>] irq_exit+0xa0/0xfc
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&rchan->lock)->rlock);
<Interrupt>
lock(&(&rchan->lock)->rlock);
*** DEADLOCK ***
3 locks held by reboot/2779:
#0: 00000000bfabfa74 (reboot_mutex){+.+.}, at: sys_reboot+0xdc/0x208
#1: 00000000c75d8c3a (&dev->mutex){....}, at: device_shutdown+0xc8/0x1c4
#2: 00000000ebec58ec (&dev->mutex){....}, at: device_shutdown+0xd8/0x1c4
stack backtrace:
CPU: 6 PID: 2779 Comm: reboot Tainted: G W 4.18.0-rc1-salvator-x-00002-g9203dbec90a68103 #41
Hardware name: Renesas Salvator-X 2nd version board based on r8a7795 ES2.0+ (DT)
Call trace:
dump_backtrace+0x0/0x148
show_stack+0x14/0x1c
dump_stack+0xb0/0xf0
print_usage_bug.part.26+0x1c4/0x27c
mark_lock+0x38c/0x610
__lock_acquire+0x3fc/0x14d4
lock_acquire+0x208/0x238
_raw_spin_lock+0x40/0x54
rcar_dmac_shutdown+0x58/0x6c
platform_drv_shutdown+0x20/0x2c
device_shutdown+0x160/0x1c4
kernel_restart_prepare+0x34/0x3c
kernel_restart+0x14/0x5c
sys_reboot+0x160/0x208
el0_svc_naked+0x30/0x34
rcar_dmac_stop_all_chan() takes the channel lock while stopping a
channel, but does not disable interrupts, leading to a deadlock when a
DMAC interrupt comes in. Before, the same code block was called from an
interrupt handler, hence taking the spinlock was sufficient.
Fix this by disabling local interrupts while taking the spinlock.
Fixes: 9203dbec90 ("dmaengine: rcar-dmac: don't use DMAC error interrupt")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch is using C++ comment style for SPDX line only,
because driver author want it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
rcar-dmac has 2 types of interrupt, 1) error IRQ (for all),
2) IRQ for each channels.
If error happens on some channels, the error IRQ will be handled
by 1), and "all" channels will be restarted.
But in this design, error handling itself will be problem for
non error channel users.
This patch removes 1) handler, and handles error IRQ on 2)
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[Kuninori: updated patch to adjust DMACHCR/DMAOR]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Updates to sprd, bam_dma, stm drivers.
- removal of VLAs in dmatest.
- Move TI drivers its own subdir.
- Switch to SPDX tags for ima/mxs dma drivers.
- Simplify getting .drvdata on bunch of drivers by Wolfram Sang.
-----BEGIN PGP SIGNATURE-----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=8mGV
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.18-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- updates to sprd, bam_dma, stm drivers
- remove VLAs in dmatest
- move TI drivers to their own subdir
- switch to SPDX tags for ima/mxs dma drivers
- simplify getting .drvdata on bunch of drivers by Wolfram Sang
* tag 'dmaengine-4.18-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (32 commits)
dmaengine: sprd: Add Spreadtrum DMA configuration
dmaengine: sprd: Optimize the sprd_dma_prep_dma_memcpy()
dmaengine: imx-dma: Switch to SPDX identifier
dmaengine: mxs-dma: Switch to SPDX identifier
dmaengine: imx-sdma: Switch to SPDX identifier
dmaengine: usb-dmac: Document R8A7799{0,5} bindings
dmaengine: qcom: bam_dma: fix some doc warnings.
dmaengine: qcom: bam_dma: fix invalid assignment warning
dmaengine: sprd: fix an NULL vs IS_ERR() bug
dmaengine: sprd: Use devm_ioremap_resource() to map memory
dmaengine: sprd: Fix potential NULL dereference in sprd_dma_probe()
dmaengine: pl330: flush before wait, and add dev burst support.
dmaengine: axi-dmac: Request IRQ with IRQF_SHARED
dmaengine: stm32-mdma: fix spelling mistake: "avalaible" -> "available"
dmaengine: rcar-dmac: Document R-Car D3 bindings
dmaengine: sprd: Move DMA request mode and interrupt type into head file
dmaengine: sprd: Define the DMA data width type
dmaengine: sprd: Define the DMA transfer step type
dmaengine: ti: New directory for Texas Instruments DMA drivers
dmaengine: shdmac: Change platform check to CONFIG_ARCH_RENESAS
...
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:
// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
Since commit 9b5ba0df4e ("ARM: shmobile: Introduce ARCH_RENESAS")
is CONFIG_ARCH_RENESAS a more appropriate platform check than the legacy
CONFIG_ARCH_SHMOBILE, hence use the former.
Renesas SuperH SH-Mobile SoCs are still covered by the CONFIG_CPU_SH4
check, just like before support for Renesas ARM SoCs was added.
Instead of blindly changing all the #ifdefs, switch the main code block
in sh_dmae_probe() to IS_ENABLED(), as this allows to remove all the
remaining #ifdefs.
This will allow to drop ARCH_SHMOBILE on ARM in the near future.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This time we have couple of new drivers along with updates to drivers.
- new driver for DesignWare AXI DMAC and MediaTek High-Speed DMA controller
- stm32 dma and qcom bam dma driver updates
- norandom test option for dmatest
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0YWt
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.17-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have couple of new drivers along with updates to drivers:
- new drivers for the DesignWare AXI DMAC and MediaTek High-Speed DMA
controllers
- stm32 dma and qcom bam dma driver updates
- norandom test option for dmatest"
* tag 'dmaengine-4.17-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (30 commits)
dmaengine: stm32-dma: properly mask irq bits
dmaengine: stm32-dma: fix max items per transfer
dmaengine: stm32-dma: fix DMA IRQ status handling
dmaengine: stm32-dma: Improve memory burst management
dmaengine: stm32-dma: fix typo and reported checkpatch warnings
dmaengine: stm32-dma: fix incomplete configuration in cyclic mode
dmaengine: stm32-dma: threshold manages with bitfield feature
dt-bindings: stm32-dma: introduce DMA features bitfield
dt-bindings: rcar-dmac: Document r8a77470 support
dmaengine: rcar-dmac: Fix too early/late system suspend/resume callbacks
dmaengine: dw-axi-dmac: fix spelling mistake: "catched" -> "caught"
dmaengine: edma: Check the memory allocation for the memcpy dma device
dmaengine: at_xdmac: fix rare residue corruption
dmaengine: mediatek: update MAINTAINERS entry with MediaTek DMA driver
dmaengine: mediatek: Add MediaTek High-Speed DMA controller for MT7622 and MT7623 SoC
dt-bindings: dmaengine: Add MediaTek High-Speed DMA controller bindings
dt-bindings: Document the Synopsys DW AXI DMA bindings
dmaengine: Introduce DW AXI DMAC driver
dmaengine: pl330: fix a race condition in case of threaded irqs
dmaengine: imx-sdma: fix pagefault when channel is disabled during interrupt
...
If serial console wake-up is enabled ("echo enabled >
/sys/.../ttySC0/power/wakeup"), and any serial input is received while
the system is suspended, serial port input no longer works after system
resume.
Note that:
1) The system can still be woken up using the serial console,
2) Serial port input keeps working if the system is woken up in some
other way (e.g. Wake-on-LAN or gpio-keys), and no serial input was
received while suspended.
To fix this, replace SET_LATE_SYSTEM_SLEEP_PM_OPS() by
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(), as the callbacks installed by the
former happen too early resp. late in the suspend resp. resume process.
Reported-by: RVC test team via Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 1131b0a4af ("dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes an issue that a race condition happens between a client
driver and the rcar-dmac driver:
- The rcar_dmac_isr_transfer_end() is called.
- The done list appears, and desc.running is the next active list.
- rcar_dmac_chan_get_residue() is called by a client driver before
rcar_dmac_isr_channel_thread() is called.
- The rcar_dmac_chan_get_residue() will not find any descriptors.
- And, the following WARNING happens:
WARN(1, "No descriptor for cookie!");
The sh-sci driver with HSCIF (921,600bps) on R-Car H3 can cause this
situation.
So, this patch checks the done lists in rcar_dmac_chan_get_residue()
and returns zero if the done lists has the argument cookie.
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
According to R-Car Gen3 Rev.0.80 manual, the DMATCR can be set to
16,777,215 as maximum. So, this patch fixes the max_chunk_size for
safety on all of SoCs. Otherwise, a system may hang if the DMATCR
is set to 0 on R-Car Gen3.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This cycle we have small update for:
- updates to xilinx and zynqmp dma controllers
- update reside calculation for rcar controller
- more RSTify fixes for documentation
- Add support for race free transfer termination and updating
for users for that
- Support for new rev of hidma with addition new APIs to
get device match data in ACPI/OF
- Random updates to bunch of other drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7bH/
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time is smallish update with updates mainly to drivers:
- updates to xilinx and zynqmp dma controllers
- update reside calculation for rcar controller
- more RSTify fixes for documentation
- add support for race free transfer termination and updating for
users for that
- support for new rev of hidma with addition new APIs to get device
match data in ACPI/OF
- random updates to bunch of other drivers"
* tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (47 commits)
dmaengine: dmatest: fix container_of member in dmatest_callback
dmaengine: stm32-dmamux: Remove unnecessary platform_get_resource() error check
dmaengine: sprd: statify 'sprd_dma_prep_dma_memcpy'
dmaengine: qcom_hidma: simplify DT resource parsing
dmaengine: xilinx_dma: Free BD consistent memory
dmaengine: xilinx_dma: Fix warning variable prev set but not used
dmaengine: xilinx_dma: properly configure the SG mode bit in the driver for cdma
dmaengine: doc: format struct fields using monospace
dmaengine: doc: fix bullet list formatting
dmaengine: ti-dma-crossbar: Fix event mapping for TPCC_EVT_MUX_60_63
dmaengine: cppi41: Fix channel queues array size check
dmaengine: imx-sdma: Add MODULE_FIRMWARE
dmaengine: xilinx_dma: Fix typos
dmaengine: xilinx_dma: Differentiate probe based on the ip type
dmaengine: xilinx_dma: fix style issues from checkpatch
dmaengine: xilinx_dma: Fix kernel doc warnings
dmaengine: xilinx_dma: Fix race condition in the driver for multiple descriptor scenario
dmaeninge: xilinx_dma: Fix bug in multiple frame stores scenario in vdma
dmaengine: xilinx_dma: Check for channel idle state before submitting dma descriptor
dmaengine: zynqmp_dma: Fix race condition in the probe
...
The current (empty) system sleep callbacks rely on the PM core to force
a runtime resume to reinitialize the DMAC registers during system
resume. Without a reinitialization, e.g. SCIF DMA will hang silently
after a system resume on R-Car Gen3.
Make this explicit by using pm_runtime_force_{suspend,resume}() as the
system sleep callbacks instead. Use SET_LATE_SYSTEM_SLEEP_PM_OPS() as
DMA engines must be initialized before all DMA slave devices.
Fixes: 17218e0092 "PM / genpd: Stop/start devices without pm_runtime_force_suspend/resume()"
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SYS/RT/Audio DMAC includes independent data buffers for reading
and writing. Therefore, the read transfer counter and write transfer
counter have different values.
TCR indicates read counter, and TCRB indicates write counter.
The relationship is like below.
TCR TCRB
[SOURCE] -> [DMAC] -> [SINK]
In the MEM_TO_DEV direction, what really matters is how much data has
been written to the device. If the DMA is interrupted between read and
write, then, the data doesn't end up in the destination, so shouldn't
be counted. TCRB is thus the register we should use in this cases.
In the DEV_TO_MEM direction, the situation is more complex. Both the
read and write side are important. What matters from a data consumer
point of view is how much data has been written to memory.
On the other hand, if the transfer is interrupted between read and
write, we'll end up losing data. It can also be important to report.
In the MEM_TO_MEM direction, what matters is of course how much data
has been written to memory from data consumer point of view.
Here, because read and write have independent data buffers, it will
take a while for TCR and TCRB to become equal. Thus we should check
TCRB in this case, too.
Thus, all cases we should check TCRB instead of TCR.
Without this patch, Sound Capture has noise after PulseAudio support
(= 07b7acb51d ("ASoC: rsnd: update pointer more accurate")), because
the recorder will use wrong residue counter which indicates transferred
from sound device, but in reality the data was not yet put to memory
and recorder will record it.
However, because DMAC is buffering data until it can be transferable
size, TCRB might not be updated.
For example, if consumer doesn't know how much data can be received,
it requests enough size to DMAC. But in reality, it might receive very
few data. In such case, DMAC just buffered it until transferable size,
and no TCRB updated.
In such case, this buffered data will be transferred if CHCR::DE bit was
cleared, and this is happen if rcar_dmac_chan_halt(). In other word, it
happen when consumer called dmaengine_terminate_all().
Because of this behavior, it need to flush buffered data when it returns
"residue" (= dmaengine_tx_status()).
Otherwise, consumer might calculate wrong things if it called
dmaengine_tx_status() and dmaengine_terminate_all() consecutively.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DMAC reads data from source device, and buffered it until transferable
size for sink device. Because of this behavior, DMAC is including
buffered data .
Now, CHCR DE bit is controlling DMA transfer enable/disable.
If DE bit was cleared during data transferring, or during buffering,
it will flush buffered data if source device was peripheral device
(The buffered data will be removed if source device was memory).
Because of this behavior, driver should ensure that DE bit is actually
0 after clearing.
This patch adds new rcar_dmac_chcr_de_barrier() and call it after CHCR
register access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anton Volkov noticed that engine->dev is NULL before
of_dma_controller_register() in probe.
Thus there might be a NULL pointer dereference in
rcar_dmac_chan_start_xfer while accessing chan->chan.device->dev which
is equal to (&dmac->engine)->dev.
On same reason, same and similar things will happen if we didn't
initialize all necessary data before calling register irq function.
To be more safety code, this patch initialize all necessary data
before calling register irq function.
Reported-by: Anton Volkov <avolkov@ispras.ru>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
- removal of AVR32 support in dw driver as AVR32 is gone
- new driver for Broadcom stream buffer accelerator (SBA) RAID driver
- add support for Faraday Technology FTDMAC020 in amba-pl08x driver
- IOMMU support in pl330 driver
- updates to bunch of drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=srPZ
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.13-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- removal of AVR32 support in dw driver as AVR32 is gone
- new driver for Broadcom stream buffer accelerator (SBA) RAID driver
- add support for Faraday Technology FTDMAC020 in amba-pl08x driver
- IOMMU support in pl330 driver
- updates to bunch of drivers
* tag 'dmaengine-4.13-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (36 commits)
dmaengine: qcom_hidma: correct API violation for submit
dmaengine: zynqmp_dma: Remove max len check in zynqmp_dma_prep_memcpy
dmaengine: tegra-apb: Really fix runtime-pm usage
dmaengine: fsl_raid: make of_device_ids const.
dmaengine: qcom_hidma: allow ACPI/DT parameters to be overridden
dmaengine: fsldma: set BWC, DAHTS and SAHTS values correctly
dmaengine: Kconfig: Simplify the help text for MXS_DMA
dmaengine: pl330: Delete unused functions
dmaengine: Replace WARN_TAINT_ONCE() with pr_warn_once()
dmaengine: Kconfig: Extend the dependency for MXS_DMA
dmaengine: mxs: Use %zu for printing a size_t variable
dmaengine: ste_dma40: Cleanup scatterlist layering violations
dmaengine: imx-dma: cleanup scatterlist layering violations
dmaengine: use proper name for the R-Car SoC
dmaengine: imx-sdma: Fix compilation warning.
dmaengine: imx-sdma: Handle return value of clk_prepare_enable
dmaengine: pl330: Add IOMMU support to slave tranfers
dmaengine: DW DMAC: Handle return value of clk_prepare_enable
dmaengine: pl08x: use GENMASK() to create bitmasks
dmaengine: pl08x: Add support for Faraday Technology FTDMAC020
...
In descriptor mode, the descriptor running pointer is not maintained
by the interrupt handler, thus, driver finds the running descriptor
from the descriptor pointer field in the CHCRB register.
But, CHCRB::DPTR indicates *next* descriptor pointer, not current.
Thus, The residue calculation will be missed. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fixes a race condition where the channel resources could be freed
before the ISR had finished running resulting in a NULL pointer
reference from the ISR.
[ 167.148934] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 167.157051] pgd = ffff80003c641000
[ 167.160449] [00000000] *pgd=000000007c507003, *pud=000000007c4ff003, *pmd=0000000000000000
[ 167.168719] Internal error: Oops: 96000046 [#1] PREEMPT SMP
[ 167.174289] Modules linked in:
[ 167.177348] CPU: 3 PID: 10547 Comm: dma_ioctl Not tainted 4.11.0-rc1-00001-g8d92afddc2f6633a #73
[ 167.186131] Hardware name: Renesas Salvator-X board based on r8a7795 (DT)
[ 167.192917] task: ffff80003a411a00 task.stack: ffff80003bcd4000
[ 167.198850] PC is at rcar_dmac_chan_prep_sg+0xe0/0x400
[ 167.203985] LR is at rcar_dmac_chan_prep_sg+0x48/0x400
Based of previous work by:
Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Implement the device_synchronize() callback which wait until a dma
channel is stopped to provide a synchronization point.
This protects the driver from multiple race conditions when terminating
and freeing resources. E.g. the completion callback still running after
device_terminate_all() has completed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The IRQ number is needed after probe to be able to add synchronisation
points in other places in the driver when freeing resources and to
implement a device_synchronize() callback. Store the IRQ number in the
struct rcar_dmac_chan so that it can be used later.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
SYS-DMAC can use 40bit address transfer, and it supports Descriptor
Mode too. Current SYS-DMAC driver disables Descriptor Mode if it was
40bit address today. But it can use Descriptor Mode with 40bit if
transfer Source/Destination address are located in same 4GiB region
in the 40 bit address space.
This patch enables it if all condition was clear
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time we fairly boring and bit small update.
- Support for Intel iDMA 32-bit hardware
- deprecate broken support for channel switching in async_tx
- bunch of updates on stm32-dma
- Cyclic support for zx dma and making in generic zx dma driver
- Small updates to bunch of other drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pcdH
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we fairly boring and bit small update.
- Support for Intel iDMA 32-bit hardware
- deprecate broken support for channel switching in async_tx
- bunch of updates on stm32-dma
- Cyclic support for zx dma and making in generic zx dma driver
- Small updates to bunch of other drivers"
* tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
async_tx: deprecate broken support for channel switching
dmaengine: rcar-dmac: Widen DMA mask to 40 bits
dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
dmaengine: Provide a wrapper for memcpy operations
dmaengine: zx: fix build warning
dmaengine: dw: we do support Merrifield SoC in PCI mode
dmaengine: dw: add support of iDMA 32-bit hardware
dmaengine: dw: introduce register mappings for iDMA 32-bit
dmaengine: dw: introduce block2bytes() and bytes2block()
dmaengine: dw: extract dwc_chan_pause() for future use
dmaengine: dw: replace convert_burst() with one liner
dmaengine: dw: register IRQ and DMA pool with instance ID
dmaengine: dw: Fix data corruption in large device to memory transfers
dmaengine: ste_dma40: indicate granularity on channels
dmaengine: ste_dma40: indicate directions on channels
dmaengine: stm32-dma: Add error messages if xlate fails
dmaengine: dw: pci: remove LPE Audio DMA ID
dmaengine: stm32-dma: Add max_burst support
dmaengine: stm32-dma: Add synchronization support
dmaengine: stm32-dma: Fix residue computation issue in cyclic mode
...
By default, the DMA mask covers only the low 32-bit address space, which
causes SWIOTLB on arm64 to fall back to a bounce buffer for DMA
transfers involving memory outside the 32-bit address space.
The R-Car DMA controller hardware supports a 40-bit address space, hence
widen the DMA mask to 40 bits to actually make use of this feature.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The slave mapping should be removed together with other channel
resources when the channel is freed. If it's not unmapped it will hang
around forever after the channel is freed.
Fixes: 9f878603db ("dmaengine: rcar-dmac: add iommu support for slave transfers")
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In usb_dmac_of_xlate(), variable ‘uchan’ is initialized but never used, which
leads to warning with W=1
drivers/dma/sh/usb-dmac.c: In function ‘usb_dmac_of_xlate’:
drivers/dma/sh/usb-dmac.c:655:24: warning: variable ‘uchan’ set but not used [-Wunused-but-set-variable]
struct usb_dmac_chan *uchan;
So remove it.
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of dmaenegine to
register a callback_result which tells them the result of the dma
transaction. Right now only one user ntb is using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no place in
kernel, this also remove NO_IRQ from dmaengine subsystem (both arm and
ppc users)
- Support for IOMMU slave transfers and it implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of driver,
and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9iA3
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of
dmaenegine to register a callback_result which tells them the
result of the dma transaction. Right now only one user (ntb) is
using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no
place in kernel, this also remove NO_IRQ from dmaengine subsystem
(both arm and ppc users)
- Support for IOMMU slave transfers and its implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of
driver, and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers"
* tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (169 commits)
async_pq_val: fix DMA memory leak
dmaengine: virt-dma: move function declarations
dmaengine: omap-dma: Enable burst and data pack for SG
DT: dmaengine: rcar-dmac: document R8A7743/5 support
dmaengine: fsldma: Unmap region obtained by of_iomap
dmaengine: jz4780: fix resource leaks on error exit return
dma-debug: fix ia64 build, use PHYS_PFN
dmaengine: coh901318: fix integer overflow when shifting more than 32 places
dmaengine: edma: avoid uninitialized variable use
dma-mapping: fix m32r build warning
dma-mapping: fix ia64 build, use PHYS_PFN
dmaengine: ti-dma-crossbar: enable COMPILE_TEST
dmaengine: omap-dma: enable COMPILE_TEST
dmaengine: edma: enable COMPILE_TEST
dmaengine: ti-dma-crossbar: Fix of_device_id data parameter usage
dmaengine: ti-dma-crossbar: Correct type for of_find_property() third parameter
dmaengine/ARM: omap-dma: Fix the DMAengine compile test on non OMAP configs
dmaengine: edma: Rename set_bits and remove unused clear_bits helper
dmaengine: edma: Use correct type for of_find_property() third parameter
dmaengine: edma: Fix of_device_id data parameter usage (legacy vs TPCC)
...
Enable slave transfers to a device behind a IPMMU by mapping the slave
addresses using the dma-mapping API.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Group slave address and transfer size in own structs for source and
destination. This is in preparation for hooking up the dma-mapping API
to the slave addresses.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The USB-DMAC's interruption happens even if the CHCR.DE is not set to 1
because CHCR.NULLE is set to 1. So, this driver should call
usb_dmac_isr_transfer_end() if the DE bit is set to 1 only. Otherwise,
the desc is possible to be NULL in the usb_dmac_isr_transfer_end().
Fixes: 0c1c8ff32f ("dmaengine: usb-dmac: Add Renesas USB DMA Controller (USB-DMAC) driver)
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is in preperation of moving to a callback that provides results to the
callback for the transaction. The conversion will maintain current behavior
and the driver must convert to new callback mechanism at a later time in
order to receive results.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is in preperation of moving to a callback that provides results to the
callback for the transaction. The conversion will maintain current behavior
and the driver must convert to new callback mechanism at a later time in
order to receive results.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cookies corresponding to pending transfers have a residue value equal to
the full size of the corresponding descriptor. The driver miscomputes
that and uses the size of the active descriptor instead. Fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[geert: Also check desc.active list]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Running descriptor pointer is set to NULL upon freeing resources. Other-
wise, rcar_dmac_issue_pending might not start new transfers
Signed-off-by: Muhammad Hamza Farooq <mfarooq@visteon.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The documentation states one should make sure both DE and TE are cleared
before starting a transaction. This patch extends the current warning to
look at both DE and TE.
Based on previous work from Muhammad Hamza Farooq.
Suggested-by: Muhammad Hamza Farooq <mfarooq@visteon.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Linus Torvalds