Provide callbacks for ndo_fdb_add, ndo_fdb_del, and ndo_fdb_dump.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Master change notifications may occur other than when joining or
leaving a bridge, for example when being added to or removed from
a bond or Open vSwitch. In that case, do nothing instead of asking
the switch driver to remove a port from a bridge that it didn't join.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move swdev wrappers over to new swdev ops (from previous ndo ops). No
functional changes to the implementation.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
rocker: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
dsa: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cd28a1a9ba ("net: dsa: fully divert PHY reads/writes if
requested") introduced a check for particular PHYs that need to be
accessed using the slave MII bus created by DSA, but this check was too
inclusive. This would prevent fixed PHYs from being successfully
registered because those should not go through the slave MII bus created
by DSA.
Make sure we check that the PHY is not a fixed PHY to prevent that from
happening.
Fixes: cd28a1a9ba ("net: dsa: fully divert PHY reads/writes if requested")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a PHY is found via Device Tree, and is also flagged by the
switch driver as needing indirect reads/writes using the switch driver
implemented MDIO bus, make sure that we bind this PHY to the slave MII
bus in order for this to happen.
Without this, we would succeed in having the PHY driver probe()'s
function to use slave MII bus read/write functions, because this is done
during dsa_slave_mii_init(), but past that point, the PHY driver would
not go through these diverted reads and writes.
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for dealing with indirect reads and writes towards
certain PHY devices, move the code which deals with binding the PHY
device to the slave MII bus created by DSA to its own function:
dsa_slave_phy_connect().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid race conditions when using the ds->ports[] array,
we need to check if the accessed port has been initialized.
Introduce and use helper function dsa_is_port_initialized
for that purpose and use it where needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support bridging offloads in DSA switch drivers, select
NET_SWITCHDEV to get access to the port_stp_update and parent_get_id
NDOs that we are required to implement.
To facilitate the integratation at the DSA driver level, we implement 3
types of operations:
- port_join_bridge
- port_leave_bridge
- port_stp_update
DSA will resolve which switch ports that are currently bridge port
members as some Switch hardware/drivers need to know about that to limit
the register programming to just the relevant registers (especially for
slow MDIO buses).
We also take care of setting the correct STP state when slave network
devices are brought up/down while being bridge members.
Finally, when a port is leaving the bridge, we make sure we set in
BR_STATE_FORWARDING state, otherwise the bridge layer would leave it
disabled as a result of having left the bridge.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A network device notifier can be called for one or more of the created
slave devices before all slave devices have been registered. This can
result in a mismatch between ds->phys_port_mask and the registered devices
by the time the call is made, and it can result in a slave device being
added to a bridge before its entry in ds->ports[] has been initialized.
Rework the initialization code to initialize entries in ds->ports[] in
dsa_slave_create. With this change, dsa_slave_create no longer needs
to return slave_dev but can return an error code instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the phy interface mode is not found in devicetree, or if devicetree
is not configured, of_get_phy_mode returns -ENODEV. The current code
sets the phy interface mode to the return value from of_get_phy_mode
without checking if it is valid.
This invalid phy interface mode is passed as parameter to of_phy_connect
or to phy_connect_direct. This sets the phy interface mode to the invalid
value, which in turn causes problems for any code using phydev->interface.
Fixes: b31f65fb43 ("net: dsa: slave: Fix autoneg for phys on switch MDIO bus")
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_phy_setup() finds the phy for the port via device tree and
using of_phy_connect(), or it uses the fall back of taking a phy from
the switch internal mdio bus and calling phy_connect_direct(). Either
way, if a phy is found, phy_attach_direct() is called to attach the
phy to the slave device.
In dsa_slave_create(), a second call to phy_attach() is made. This
results in the warning "PHY already attached". Remove this second,
redundant attaching of the phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering a mdio bus, Linux assumes than every port has a PHY and tries
to scan it. If a switch port has no PHY registered, DSA will fail to register
the slave MII bus. To fix this, set the slave MII bus PHY mask to the switch
PHYs mask.
As an example, if we use a Marvell MV88E6352 (which is a 7-port switch with no
registered PHYs for port 5 and port 6), with the following declared names:
static struct dsa_chip_data switch_cdata = {
[...]
.port_names[0] = "sw0",
.port_names[1] = "sw1",
.port_names[2] = "sw2",
.port_names[3] = "sw3",
.port_names[4] = "sw4",
.port_names[5] = "cpu",
};
DSA will fail to create the switch instance. With the PHY mask set for the
slave MII bus, only the PHY for ports 0-4 will be scanned and the instance will
be successfully created.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we cannot attach to our slave netdevice PHY, error out and
propagate that error up to the caller: dsa_slave_create().
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Andrey Volkov <andrey.volkov@nexvision.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case there is no PHY at the designated address on the internal
switch, we would basically de-reference a null pointer here:
dsa_slave_phy_setup(...)
{
p->phy = ds->slave_mii_bus->phy_map[p->port];
phy_connect_direct(slave_dev, p->phy, dsa_slave_adjust_link,
^------
This can be triggered when the platform configuration (platform_data or
Device Tree) indicates there should be a PHY device at this address, but
the HW is non-responsive, such that we cannot attach a PHY device at
this specific location.
Fix this by checking the return value prior to calling
phy_connect_direct().
CC: Andrew Lunn <andrew@lunn.ch>
Fixes: b31f65fb43 ("net: dsa: slave: Fix autoneg for phys on switch MDIO bus")
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Andrey Volkov <andrey.volkov@nexvision.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neaten and standardize the logging output.
Other miscellanea:
o Use pr_notice_once instead of a guard flag.
o Convert existing pr_<level> uses too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ports phys are connected to the switches internal MDIO bus,
we need to connect the phy to the slave netdev, otherwise
auto-negotiation etc, does not work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading switch registers with 'ethtool -d'.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some chips it is possible to access the switch eeprom.
Add infrastructure support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for the presence or not of the optional switch function
get_phy_flags() called the function, rather than checked to see if it
is a NULL pointer. This causes a derefernce of a NULL pointer on all
switch chips except the sf2, the only switch to implement this call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6819563e64 ("net: dsa: allow switch drivers to specify phy_device::dev_flags")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/dsa/slave.c uses functions and structures declared in phy_fixed.h
but does not explicitely include it, while dsa.h needs structure
declarations for 'struct ethtool_wolinfo' and 'struct ethtool_eee', fix
those by including the correct header files.
Fixes: ec9436baed ("net: dsa: allow drivers to do link adjustment")
Fixes: ce31b31c68 ("net: dsa: allow updating fixed PHY link information")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f7f1de51ed ("net: dsa: start and stop the PHY state machine")
add calls to phy_start() in dsa_slave_open() respectively phy_stop() in
dsa_slave_close().
We also call phy_start_aneg() in dsa_slave_create(), and this call is
messing up with the PHY state machine, since we basically start the
auto-negotiation, and later on restart it when calling phy_start().
phy_start() does not currently handle the PHY_FORCING or PHY_AN states
properly, but such a fix would be too invasive for this window.
Fixes: f7f1de51ed ("net: dsa: start and stop the PHY state machine")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switches driver to query and enable/disable EEE on a per-port
basis by implementing the ethtool_{get,set}_eee settings and delegating
these operations to the switch driver.
set_eee() will need to coordinate with the PHY driver to make sure that
EEE is enabled, the link-partner supports it and the auto-negotiation
result is satisfactory.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a per-port network device is used/unused, invoke the switch
driver port_enable/port_disable callbacks to allow saving as much power
as possible by disabling unused parts of the switch (RX/TX logic, memory
arrays, PHYs...). We supply a PHY device argument to make sure the
switch driver can act on the PHY device if needed (like putting/taking
the PHY out of deep low power mode).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_open() should start the PHY library state machine for its PHY
interface, and dsa_slave_close() should stop the PHY library state
machine accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switch drivers to implement per-port Wake-on-LAN getter and
setters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an abstraction layer to suspend/resume switch devices, doing the
following split:
- suspend/resume the slave network devices and their corresponding PHY
devices
- suspend/resume the switch hardware using switch driver callbacks
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch drivers (e.g: bcm_sf2) may have to communicate specific
workarounds or flags towards the PHY device driver. Allow switches
driver to be delegated that task by introducing a get_phy_flags()
callback which will do just that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev. From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.
So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change addresses several issues.
First, it was possible to set tag_protocol without setting the ops pointer.
To correct that I have reordered things so that rcv is now populated before
we set tag_protocol.
Second, it didn't make much sense to keep setting the device ops each time a
new slave was registered. So by moving the receive portion out into root
switch initialization that issue should be addressed.
Third, I wanted to avoid sending tags if the rcv pointer was not registered
so I changed the tag check to verify if the rcv function pointer is set on
the root tree. If it is then we start sending DSA tagged frames.
Finally I split the device ops pointer in the structures into two spots. I
placed the rcv function pointer in the root switch since this makes it
easiest to access from there, and I placed the xmit function pointer in the
slave for the same reason.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we introduced an additional multiplexing/demultiplexing layer
with commit 3e8a72d1da ("net: dsa: reduce number of protocol hooks")
that lives within the DSA code, we no longer need to have a given switch
driver tag_protocol be an actual ethertype value, instead, we can
replace it with an enum: dsa_tag_protocol.
Do this replacement in the drivers, which allows us to get rid of the
cpu_to_be16()/htons() dance, and remove ETH_P_BRCMTAG since we do not
need it anymore.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the 4-bytes Broadcom tag that built-in switches such as
the Starfighter 2 might insert when receiving packets, or that we need
to insert while targetting specific switch ports. We use a fake local
EtherType value for this 4-bytes switch tag: ETH_P_BRCMTAG to make sure
we can assign DSA-specific network operations within the DSA drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switch drivers to hook a PHY link update callback to perform
port-specific link work.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever libphy determines that the link status of a given PHY/port has
changed, allow to call into the switch driver link adjustment callback
so proper actions can be taken care of by the switch driver upon link
notification.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case switch port tagging is disabled (voluntarily, or the switch just
does not support it), allow us to continue using the defined set of
dsa_device_ops in net/dsa/slave.c.
We introduce dsa_protocol_is_tagged() to check whether we need to
override skb->protocol and go through the DSA-specifif packet_type
function, or if we just go on and receive the SKB through the normal
path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the DSA slave interface to be bound to an arbitray PHY, not just
the ones that are available as child PHY devices of the switch MDIO bus.
This allows us for instance to have external PHYs connected to a
separate MDIO bus, but yet also connected to a given switch port.
Under certain configurations, the physical port mask might not be a 1:1
mapping to the MII PHYs mask. This is the case, if e.g: Port 1 of the
switch is used and connects to a PHY at a MDIO address different than 1.
Introduce a phys_mii_mask variable which allows driver to implement and
divert their own MDIO read/writes operations for a subset of the MDIO
PHY addresses.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will later use the per-port device_node pointer to fetch a bunch of
port-specific properties.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA is currently registering one packet_type function per EtherType it
needs to intercept in the receive path of a DSA-enabled Ethernet device.
Right now we have three of them: trailer, DSA and eDSA, and there might
be more in the future, this will not scale to the addition of new
protocols.
This patch proceeds with adding a new layer of abstraction and two new
functions:
dsa_switch_rcv() which will dispatch into the tag-protocol specific
receive function implemented by net/dsa/tag_*.c
dsa_slave_xmit() which will dispatch into the tag-protocol specific
transmit function implemented by net/dsa/tag_*.c
When we do create the per-port slave network devices, we iterate over
the switch protocol to assign the DSA-specific receive and transmit
operations.
A new fake ethertype value is used: ETH_P_XDSA to illustrate the fact
that this is no longer going to look like ETH_P_DSA or ETH_P_TRAILER
like it used to be.
This allows us to greatly simplify the check in eth_type_trans() and
always override the skb->protocol with ETH_P_XDSA for Ethernet switches
tagged protocol, while also reducing the number repetitive slave
netdevice_ops assignments.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ether_addr_copy instead of memcpy(a, b, ETH_ALEN) to
save some cycles on arm and powerpc.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The slave MII bus registered by the DSA code is using the parent MII bus
as part of its name (ds->master_mii_bus_id), in case the parent MII bus
name is already 16 characters long (such as d0072004.mdio-mi) we will
get the following WARN_ON in dsa_switch_setup() when calling
mdiobus_register():
[ 79.088782] ------------[ cut here ]------------
[ 79.093448] WARNING: at fs/sysfs/dir.c:536 sysfs_add_one+0x80/0xa0()
[ 79.099831] sysfs: cannot create duplicate filename
'/class/mdio_bus/d0072004.mdio-mi'
This is a genuine warning, because the DSA slave MII bus will also be
named d0072004.mdio-mi, and since MII_BUS_ID_SIZE is 17 characters long
(with null-terminator) the following will truncate the slave MII bus id:
snprintf(ds->slave_mii_bus->id, MII_BUS_ID_SIZE, "%s-%d:%.2x",
ds->master_mii_bus->id, ds->pd->sw_addr);
Fix this by using dsa-<switch index->:<sw_add> which is guaranteed to be
unique.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove set_sg from DSA slave ethtool_ops. Features inheritance looks
broken/not fully implemented anyway.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.
Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
+little renaming of unicast functions to be smooth with multicast ones
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck