On usual A64 board design the power of HDMI controller is connected to
DLDO1 of the AXP803 PMIC. If this regulator is shut down, the HDMI
output will be blank. Therefore the simplefb driver should keep this
regulator on.
Add the regulator to all currently available A64 boards' simplefb_hdmi
device node, if the board is capable of outputing HDMI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As the U-Boot bootloader now is also capable of initialize the HDMI on
A64 boards, add a simplefb device tree node for accessing the HDMI
framebuffer initialized by the bootloader.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As we have all necessary parts to enable the DE2 CCU on the Allwinner
A64 SoC, add the needed device tree nodes, including the DE2 CCU itself
and the DE2 bus.
The "mixer0-lcd0" simplefb device node is updated to use the DE2 CCU.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pine H64 has 3 GPIO-controlled LEDs, which are labeled "heartbeat",
"link", and "status".
Add device nodes for them.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Currently all ARM kernels will have s2idle enabled if CONFIG_SUSPEND is
present. In this case if the lid is closed, systemd-logind will enter
s2idle mode by default; however there's no possible wakeup source
defined, so the system will enter a forever idle.
Add the lid itself as a wakeup source, thus the system can wakeup when
the lid is opened.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Originally the name of the DLDO3 regulator on TERES-I is "eDP12", which
is not consistent with other regulator names.
Change it to "vdd-edp", in order to make it more consistent.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The card detect GPIO for Sopine and Pine64-LTS is PF6.
Add this to the dts.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 has a SRAM controller, and in the device tree currently
we have a syscon node to enable EMAC driver to access the EMAC clock
register. As SRAM controller driver can now export regmap for this
register, replace the syscon node to the SRAM controller device node,
and let EMAC driver to acquire its EMAC clock regmap.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Updated compatible string]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Pinebook is a A64-based laptop produced by Pine64, with the following
peripherals:
USB:
- Two external USB ports (one is directly connected to A64's OTG
controller, the other is under a internal hub connected to the host-only
controller.)
- USB HID keyboard and touchpad connected to the internal hub.
- USB UVC camera connected to the internal hub.
Power-related:
- A DC IN jack connected to AXP803's DCIN pin.
- A Li-Polymer battery connected to AXP803's battery pins.
Storage:
- An eMMC by Foresee on the main board (in the product revision of the
main board it's designed to be switchable).
- An external MicroSD card slot.
Display:
- An eDP LCD panel (1366x768) connected via an ANX6345 RGB-eDP bridge.
- A mini HDMI port.
Misc:
- A Hall sensor designed to detect the status of lid, connected to GPIO PL12.
- A headphone jack connected to the SoC's internal codec.
- A debug UART port muxed with headphone jack.
This commit adds basical support for it.
[vasily: squashed several commits into one, added simplefb node, added usbphy
to ehci0 and ohci0 nodes and other cosmetic changes to dts]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner A64 SoC features two PWM controllers, which are fully
compatible to the one used in the A13 and H3 chips.
Add the nodes for the devices (one for the "normal" PWM, the other for
the one in the CPUS domain) and the pins their outputs are connected to.
On the A64 the "normal" PWM is muxed together with one of the MDIO pins
used to communicate with the Ethernet PHY, so it won't be usable on many
boards. But the Pinebook laptop uses this pin for controlling the LCD
backlight.
On Pine64 the CPUS PWM pin however is routed to the "RPi2" header,
at the same location as the PWM pin on the RaspberryPi.
Tested on Pinebook and Teres-I
[vasily: fixed comment message as requested by Stefan Bruens, added default
muxing options to pwm and r_pwm nodes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Outside of SOC few chips need external clock source
through RTC example Wifi chip. So RTC clock nodes to
phandle 32kHz external oscillator.
prefix rtc- with clock-output-names defined in
dt-binding to avoid confusion with existing osc32k name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The OrangePi PC2 have an mx25l1606e spi flash.
Add a node for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Sopine and Pine64-LTS have a winbond w25q128 spi flash on spi0.
Add a node for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We mostly have some changes to support the H6, Allwinner latest SoC. We're
still in the preliminary phase, with I2C, pinctrl and clock support.
-----BEGIN PGP SIGNATURE-----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=d7Ql
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 changes for 4.18
We mostly have some changes to support the H6, Allwinner latest SoC. We're
still in the preliminary phase, with I2C, pinctrl and clock support.
* tag 'sunxi-dt64-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: h6: add PCF8563 RTC on Pine H64 board
arm64: allwinner: h6: add R_I2C controller
arm64: allwinner: h6: add R_INTC interrupt controller
arm64: allwinner: h6: add node for R_PIO pin controller
arm64: allwinner: h6: add PRCM CCU device node
arm64: dts: allwinner: a64: bananapi-m64: add usb otg
arm64: dts: allwinner: axp803: Add drivevbus regulator
arm64: allwinner: h6: restore the usage of CCU slice macros
Signed-off-by: Olof Johansson <olof@lixom.net>
Pine H64 board has a PCF8563 dedicated RTC connected to its R_I2C bus.
Enable the R_I2C bus and add the RTC to the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has a R_I2C controller wired to the PL0/PL1 pins, which
are used in the reference design to connect AXP805 PMIC.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has also a R_INTC interrupt controller like Allwinner
A64 SoC, but has its base address changed due to the memory map change
in H6.
Add it into the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has a R_PIO pin controller which controls PL and PM
GPIO banks.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 has also a PRCM CCU.
Add its device node into the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H2+, H3,
or H5 SoCs with the same PCB.
The board has 2GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.
This patch enables the H5 variant using the H3 board definition moved to
a common dtsi in an earlier patch. The dts simply include the common dtsi
and declares the correct compatible and model of the H5 variant.
Suggested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The dtb entries for NanoPi boards in the device tree makefile somehow
ended up after the Orange Pi boards.
Move them so the list is properly sorted.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
At the board level, we want to be able to specify what regulator
supplies power to the cpu domain.
Add a label to the first cpu node so we can reference it later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add usb otg support for bananapi-m64 board,
- USB-ID connected with PH9
- USB-DRVVBUS controlled by N_VBUSEN pin from PMIC
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add reg_drivevbus regualtor for boards which are using
external regulator to drive the OTG VBus through N_VBUSEN
PMIC pin.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
As the definition of CCU slice macros are already merged into the source
tree, restore the usage of the macros now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
-----BEGIN PGP SIGNATURE-----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=hXvM
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard:
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
* tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus
ARM: dts: sun8i-h3: Add Mali node
ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards
ARM: dts: sun8i: h3: Enable HDMI output on H3 boards
ARM: dts: sunxi: h3/h5: Add HDMI pipeline
ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node
ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi
ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl
ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
ARM: dts: nanopi-neo-air: Add WiFi / eMMC
The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG
This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.
Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 SoC features two display pipelines, one has a LCD output, the
other has a HDMI output.
Add support for simplefb for the LCD output. Tested on Teres I.
This patch was inspired by work of Icenowy Zheng.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add a watchdog node for the A64, automatically enabled on all boards.
Since the device is compatible with an existing driver, we only reserve
a new compatible string to be used together with the fall back.
Tested on Olimex Teres-I.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the proper pin group node to reference in board files.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:
- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situation only 3GiB is
accessible)
- AXP805 PMIC
- Raspberry-Pi-compatible GPIO header, "Euler" GPIO header (not
compatible with the "Euler" on Pine A64) and "Expansion" pin header
- 2 USB 2.0 ports and 1 USB 3.0 ports
- Audio jack
- MicroSD slot and eMMC module slot
- on-board SPI NOR flash
- 1Gbps Ethernet port (via RTL8211E PHY)
- HDMI port
Adds initial support for it, including the UART on the Expansion pin
header.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 is a new SoC with Cortex-A53 cores from Allwinner, with its
memory map fully reworked and some high-speed peripherals (PCIe, USB
3.0) introduced.
This commit adds the basical DTSI file of it, including the clock
support and UART support.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable HDMI output on all boards with HDMI connector.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Most of the boards use the mmc1 pins and their attributes defined in
mmc1_pins_a. Let's default to that by moving the pinctrl attributes to
the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the DAI blocks to the device tree. I2S0 and I2S1 are for
connecting to an external codec.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The S/PDIF transmitter can be reached on the Euler connector.
But as this is a GPIO then leave it disabled so that an overlay
can override the status property.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the device tree sound bindings for the S/PDIF block.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF transceiver controller block and pin to the A64 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most of the boards use the mmc0 pins and their attributes defined in
mmc0_pins_a. Let's default to those by moving the pinctrl attributes
to the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We get a moderate number of new machines this time, and only one
new SoC variant (Actions S700):
Actions:
S700 Soc and CubieBoard7 development board
Allo.com Sparky Single-board-computer
Allwinner:
Orange Pi R1 development board
Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
Axentia Nattis/Natte digital signage
sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
SolidRun Humminboard2 development board
Variscite DART-MX6 SoM and Carrier-board
Technologic TS-4600 and TS-7970 development board
Toradex Colibri iMX7D SoM board
v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
Moxa UC-8410A Series industrial computer
Gemini:
D-Link DNS-313 NAS enclosure
OMAP:
LogicPD OMAP35xx SOM-LV devkit
LogicPD OMAP35xx Torpedo devkit
Renesas:
r8a77970 (V3M) Starter Kit board
r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
Aspeed clk controller support
Freescale LS1088A, LS1021A device support
Gemini Ethernet, PCI, TVE, panel
Keystone gpio, qspi, more uarts
Mediatek cpufreq, regulator, clock, reset
Marvell thermal, cpufreq, nand
Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
Rockchip Mipi, GPU, display
Samsung Exynos5433 PMU, power domain, nfc
Spreadtrum: sc9860 clocks
Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJac0fiAAoJEGCrR//JCVInGUYP/ikTcjrmtQxmMINdsy88gmN3
lPk3jGoViyRzc9Y6hGUUXn1YNdK8+IqRkqLnhtVX3cOLS5pP2HwsvSgPmSSB3eQe
NOhXUNRQaTbeS/eBGZxJbxEKSowQHU+43M2kRNQOht7UQzS8NnBj/1RGaxcFyNSw
gIixWDZLgVTNCSloPaSrZmiwSa7rSM2q0ncBzzeafAZiTRNeOb6IUpnqu/n0Qnot
er6VoEyxp6ThFqRB7O8bCAIwgqlyB9xSGBPNR/JI0e0xXo3KVE/2AjHYDHVP/Ttx
X8vtb3m+RED7tX4oCmlrHb1SAAKpNi1Vzdg4PxmKCa7yb5xPog7OEr3rnpijzCL0
y8IJLlVSPyx31yB7mIIzCjrcISrT7tOXp0ha88/NgNsGXw5Ln0GVEqTkmSrz/JWo
z1G2tNwnstS64KK+chHOZfUto4Rzbrpmr9L1ziKIpSQtiNyOmiSu1c3EjHim7x4I
Mfiv6+8J71faUYuKVK1oaX0gi43oSZHu4NuniQy8dg/OIpgPpHHpG1qCyAzgC6Pa
r1Am2w33CXrJI78b4zG2pIDx0HghIjFUtjX9tijoFiMs1EZgbV6cJ2meep6Sy+XV
RBxHXPU8obdcuBfhgjEygwLI0HSe0R78B15qPP/SNxAFeAvE950xfPrGAoZg7qo/
o6B2iQSfsYQJbD8rUHaA
=qN1F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE0VqZU19dR2zEVaqr0rTAlCFNr3QFAlpPTzIACgkQ0rTAlCFN
r3SwvRAAkG4Idi3wsORz0+RwIFLHeiPNzE4iGrnwAsX1RhlYn17LHcGA2xBkV5d9
Khk1AoOKkhpNKJ11e1UFffU0jMeibDXaWEbcE3fhLP6X3wnkuspOZuSCsk94C+oU
xLOKVTy9Kw+yQPvOzqWmiI84YCSkH1SGw1mPOnTUD2Nz7Soux9I6hr3AO6x50pIW
5dq9tbxNN53YARc28ydOFtChnR2NTPQrLnGefU3eFjMp4F1xcEZq54TN3kBbF5U2
x7rbDunDh13EI8Qhi1jzgnKedXkkSFc3Zm0IhnjzEVVms9TS0Fz0b5KDT8RG/f9+
O3hHXcsvCnxadULcq4xEWB4WV3Xjmt8x6Y8RUlkYFgBfA2iOJcqd2jJbWB98iaVB
Ce7w+48yBWVkG35vGIGpmO/TiY8czicveFy2T98zDmHPiwzCNn3+0XExDQsgklt7
gR/8CWCqVDhK0XnZadntkZuq/bXOJzVQ2BpnZXIC+cGz1GjmAGR9Ey5l2VusBZLU
zEhTGbyBbfaJikR+4sRxkPx7DFkvjXbM/Y/cEHgD0CqZboynFLgPiewHTRcCTYWb
4qaBI660jYINHetQWdCG2Iz3gjAjaJEyEBtK61BDL9hX4del2hVwvq7t7F7NMV6L
EZFCDDUOfky56gKCYSXPWU/S6MX5hzIw8Y5/csQVMQCOoOkqe7o=
=bDG2
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.16, bis
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
* tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable the LCD
ARM: dts: sun8i: a83t: Add LVDS pins group
ARM: dts: sun8i: a83t: Enable the PWM
ARM: dts: sun8i: a83t: Add display pipeline
ARM: sunxi: h3/h5: add simplefb nodes
arm64: allwinner: h5: add compatible string for DE2 CCU
ARM: sun8i: h3/h5: add DE2 CCU device node for H3
dt-bindings: simplefb-sunxi: add pipelines for DE2
ARM: dts: sun8i: fix USB Ethernet of Orange Pi R1
Signed-off-by: Olof Johansson <olof@lixom.net>
The DE2 CCU on Allwinner H5 SoC has a slightly different behavior than
the one on H3, so the compatible string is not set in the common DTSI
file.
Add the compatible string of H5 DE2 CCU in H5 DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Bananapi-M64 has 3 LEDS in red, green, and blue. These are toggled
via GPIO lines, which drive transistors that control current across the
LEDS. The red LED is by default on, via an additional pull-up on the
control line. We consider this means that it is a power indicator.
So we set the "default-on" property for it.
The pingroups the GPIO lines belong to require external regulators be
enabled to be able to drive the GPIO high. These regulators also have
other purposes. However the pin controller does not have bindings for
regulators. Here we just set them to always-on.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sdcard detect pin on orange-pi-zero-plus2 is pulled up.
Fix cd-gpio description to enable sdcard detect.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Icenowy Zheng