GSO isn't the only offload feature with restrictions that
potentially can't be expressed with the current features mechanism.
Checksum is another although it's a general issue that could in
theory apply to anything. Even if it may be possible to
implement these restrictions in other ways, it can result in
duplicate code or inefficient per-packet behavior.
This generalizes ndo_gso_check so that drivers can remove any
features that don't make sense for a given packet, similar to
netif_skb_features(). It also converts existing driver
restrictions to the new format, completing the work that was
done to support tunnel protocols since the issues apply to
checksums as well.
By actually removing features from the set that are used to do
offloading, it solves another problem with the existing
interface. In these cases, GSO would run with the original set
of features and not do anything because it appears that
segmentation is not required.
CC: Tom Herbert <therbert@google.com>
CC: Joe Stringer <joestringer@nicira.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Tom Herbert <therbert@google.com>
Fixes: 04ffcb255f ("net: Add ndo_gso_check")
Tested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using VXLAN tunnels and a sky2 device, I have experienced
checksum failures of the following type:
[ 4297.761899] eth0: hw csum failure
[...]
[ 4297.765223] Call Trace:
[ 4297.765224] <IRQ> [<ffffffff8172f026>] dump_stack+0x46/0x58
[ 4297.765235] [<ffffffff8162ba52>] netdev_rx_csum_fault+0x42/0x50
[ 4297.765238] [<ffffffff8161c1a0>] ? skb_push+0x40/0x40
[ 4297.765240] [<ffffffff8162325c>] __skb_checksum_complete+0xbc/0xd0
[ 4297.765243] [<ffffffff8168c602>] tcp_v4_rcv+0x2e2/0x950
[ 4297.765246] [<ffffffff81666ca0>] ? ip_rcv_finish+0x360/0x360
These are reliably reproduced in a network topology of:
container:eth0 == host(OVS VXLAN on VLAN) == bond0 == eth0 (sky2) -> switch
When VXLAN encapsulated traffic is received from a similarly
configured peer, the above warning is generated in the receive
processing of the encapsulated packet. Note that the warning is
associated with the container eth0.
The skbs from sky2 have ip_summed set to CHECKSUM_COMPLETE, and
because the packet is an encapsulated Ethernet frame, the checksum
generated by the hardware includes the inner protocol and Ethernet
headers.
The receive code is careful to update the skb->csum, except in
__dev_forward_skb, as called by dev_forward_skb. __dev_forward_skb
calls eth_type_trans, which in turn calls skb_pull_inline(skb, ETH_HLEN)
to skip over the Ethernet header, but does not update skb->csum when
doing so.
This patch resolves the problem by adding a call to
skb_postpull_rcsum to update the skb->csum after the call to
eth_type_trans.
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_scrub_packet() is called when a packet switches between a context
such as between underlay and overlay, between namespaces, or between
L3 subnets.
While we already scrub the packet mark, connection tracking entry,
and cached destination, the security mark/context is left intact.
It seems wrong to inherit the security context of a packet when going
from overlay to underlay or across forwarding paths.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vlan tags are stacked, it is very likely that the outer tag is stored
in skb->vlan_tci and skb->protocol shows the inner tag's vlan_proto.
Currently netif_skb_features() first looks at skb->protocol even if there
is the outer tag in vlan_tci, thus it incorrectly retrieves the protocol
encapsulated by the inner vlan instead of the inner vlan protocol.
This allows GSO packets to be passed to HW and they end up being
corrupted.
Fixes: 58e998c6d2 ("offloading: Force software GSO for multiple vlan tags.")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes MPLS GSO for case when mpls is compiled as kernel module.
Fixes: 0d89d2035f ("MPLS: Add limited GSO support").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rearranges the loop in net_rx_action to reduce the
amount of jumping back and forth when reading the code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should only perform the softnet_break check after we have polled
at least one device in net_rx_action. Otherwise a zero or negative
setting of netdev_budget can lock up the whole system.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit d75b1ade56 (net: less
interrupt masking in NAPI) required drivers to leave poll_list
empty if the entire budget is consumed.
We have already had two broken drivers so let's add a check for
this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a new function napi_poll and moves the napi
polling code from net_rx_action into it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cecda693a9 ("net: keep original skb
which only needs header checking during software GSO") keeps the original
skb for packets that only needs header check, but it doesn't drop the
packet if software segmentation or header check were failed.
Fixes cecda693a9 ("net: keep original skb which only needs header checking during software GSO")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix NBMA tunnel mac header handling in GRE, from Timo Teräs.
2) Fix a NAPI race in the fec driver, from Nimrod Andy.
3) The new IFF_VNET_LE bit is outside the size of the flags member it
is stored in (which is 16-bits), store the state locally in the
drivers. From Michael S Tsirkin.
4) We are kicking the tires with the new wireless maintainership
situation. Bluetooth fixes via Johan Hedberg, and mac80211 fixes
from Johannes Berg.
5) Fix locking and leaks in geneve driver, from Jesse Gross.
6) Make netlink TX mmap code always copy, so we don't have to be
potentially exposed to the user changing the underlying contents
from underneath us.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
be2net: Fix incorrect setting of tunnel offload flag in netdev features
bnx2x: fix typos in "configure"
xen-netback: support frontends without feature-rx-notify again
MAINTAINERS: changes for wireless
cxgb4: Fix decoding QSA module for ethtool get settings
geneve: Fix races between socket add and release.
geneve: Remove socket and offload handlers at destruction.
netlink: Don't reorder loads/stores before marking mmap netlink frame as available
netlink: Always copy on mmap TX.
Bluetooth: Fix bug with filter in service discovery optimization
mac80211: free management frame keys when removing station
net: Disallow providing non zero VLAN ID for NIC drivers FDB add flow
net/mlx4: Cache line CQE/EQE stride fixes
net: fec: Fix NAPI race
xen-netfront: use napi_complete() correctly to prevent Rx stalling
ip_tunnel: Add missing validation of encap type to ip_tunnel_encap_setup()
ip_tunnel: Add sanity checks to ip_tunnel_encap_add_ops()
net: Allow FIXED_PHY to be modular.
if_tun: drop broken IFF_VNET_LE
macvtap: drop broken IFF_VNET_LE
...
Pull vfs pile #2 from Al Viro:
"Next pile (and there'll be one or two more).
The large piece in this one is getting rid of /proc/*/ns/* weirdness;
among other things, it allows to (finally) make nameidata completely
opaque outside of fs/namei.c, making for easier further cleanups in
there"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
coda_venus_readdir(): use file_inode()
fs/namei.c: fold link_path_walk() call into path_init()
path_init(): don't bother with LOOKUP_PARENT in argument
fs/namei.c: new helper (path_cleanup())
path_init(): store the "base" pointer to file in nameidata itself
make default ->i_fop have ->open() fail with ENXIO
make nameidata completely opaque outside of fs/namei.c
kill proc_ns completely
take the targets of /proc/*/ns/* symlinks to separate fs
bury struct proc_ns in fs/proc
copy address of proc_ns_ops into ns_common
new helpers: ns_alloc_inum/ns_free_inum
make proc_ns_operations work with struct ns_common * instead of void *
switch the rest of proc_ns_operations to working with &...->ns
netns: switch ->get()/->put()/->install()/->inum() to working with &net->ns
make mntns ->get()/->put()/->install()/->inum() work with &mnt_ns->ns
common object embedded into various struct ....ns
The current implementations all use dev_uc_add_excl() and such whose API
doesn't support vlans, so we can't make it with NICs HW for now.
Fixes: f6f6424ba7 ('net: make vid as a parameter for ndo_fdb_add/ndo_fdb_del')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull crypto update from Herbert Xu:
- The crypto API is now documented :)
- Disallow arbitrary module loading through crypto API.
- Allow get request with empty driver name through crypto_user.
- Allow speed testing of arbitrary hash functions.
- Add caam support for ctr(aes), gcm(aes) and their derivatives.
- nx now supports concurrent hashing properly.
- Add sahara support for SHA1/256.
- Add ARM64 version of CRC32.
- Misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (77 commits)
crypto: tcrypt - Allow speed testing of arbitrary hash functions
crypto: af_alg - add user space interface for AEAD
crypto: qat - fix problem with coalescing enable logic
crypto: sahara - add support for SHA1/256
crypto: sahara - replace tasklets with kthread
crypto: sahara - add support for i.MX53
crypto: sahara - fix spinlock initialization
crypto: arm - replace memset by memzero_explicit
crypto: powerpc - replace memset by memzero_explicit
crypto: sha - replace memset by memzero_explicit
crypto: sparc - replace memset by memzero_explicit
crypto: algif_skcipher - initialize upon init request
crypto: algif_skcipher - removed unneeded code
crypto: algif_skcipher - Fixed blocking recvmsg
crypto: drbg - use memzero_explicit() for clearing sensitive data
crypto: drbg - use MODULE_ALIAS_CRYPTO
crypto: include crypto- module prefix in template
crypto: user - add MODULE_ALIAS
crypto: sha-mb - remove a bogus NULL check
crytpo: qat - Fix 64 bytes requests
...
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
0day robot reported the following crash:
[ 21.233581] BUG: unable to handle kernel NULL pointer dereference at 0000000000000007
[ 21.234709] IP: [<ffffffff8156ebda>] sk_attach_bpf+0x39/0xc2
It's due to bpf_prog_get() returning ERR_PTR.
Check it properly.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 89aa075832 ("net: sock: allow eBPF programs to be attached to sockets")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce helper macro for_each_cmsghdr as a wrapper of the enumerating
cmsghdr from msghdr, just cleanup.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
This change pulls the core functionality out of __netdev_alloc_skb and
places them in a new function named __alloc_rx_skb. The reason for doing
this is to make these bits accessible to a new function __napi_alloc_skb.
In addition __alloc_rx_skb now has a new flags value that is used to
determine which page frag pool to allocate from. If the SKB_ALLOC_NAPI
flag is set then the NAPI pool is used. The advantage of this is that we
do not have to use local_irq_save/restore when accessing the NAPI pool from
NAPI context.
In my test setup I saw at least 11ns of savings using the napi_alloc_skb
function versus the netdev_alloc_skb function, most of this being due to
the fact that we didn't have to call local_irq_save/restore.
The main use case for napi_alloc_skb would be for things such as copybreak
or page fragment based receive paths where an skb is allocated after the
data has been received instead of before.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the netdev_alloc_frag function up so that it can be used
on one of two page frag pools instead of being fixed on the
netdev_alloc_cache. By doing this we can add a NAPI specific function
__napi_alloc_frag that accesses a pool that is only used from softirq
context. The advantage to this is that we do not need to call
local_irq_save/restore which can be a significant savings.
I also took the opportunity to refactor the core bits that were placed in
__alloc_page_frag. First I updated the allocation to do either a 32K
allocation or an order 0 page. This is based on the changes in commmit
d9b2938aa where it was found that latencies could be reduced in case of
failures. Then I also rewrote the logic to work from the end of the page to
the start. By doing this the size value doesn't have to be used unless we
have run out of space for page fragments. Finally I cleaned up the atomic
bits so that we just do an atomic_sub_and_test and if that returns true then
we set the page->_count via an atomic_set. This way we can remove the extra
conditional for the atomic_read since it would have led to an atomic_inc in
the case of success anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle are:
- 'Nested Sleep Debugging', activated when CONFIG_DEBUG_ATOMIC_SLEEP=y.
This instruments might_sleep() checks to catch places that nest
blocking primitives - such as mutex usage in a wait loop. Such
bugs can result in hard to debug races/hangs.
Another category of invalid nesting that this facility will detect
is the calling of blocking functions from within schedule() ->
sched_submit_work() -> blk_schedule_flush_plug().
There's some potential for false positives (if secondary blocking
primitives themselves are not ready yet for this facility), but the
kernel will warn once about such bugs per bootup, so the warning
isn't much of a nuisance.
This feature comes with a number of fixes, for problems uncovered
with it, so no messages are expected normally.
- Another round of sched/numa optimizations and refinements, for
CONFIG_NUMA_BALANCING=y.
- Another round of sched/dl fixes and refinements.
Plus various smaller fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched: Add missing rcu protection to wake_up_all_idle_cpus
sched/deadline: Introduce start_hrtick_dl() for !CONFIG_SCHED_HRTICK
sched/numa: Init numa balancing fields of init_task
sched/deadline: Remove unnecessary definitions in cpudeadline.h
sched/cpupri: Remove unnecessary definitions in cpupri.h
sched/deadline: Fix rq->dl.pushable_tasks bug in push_dl_task()
sched/fair: Fix stale overloaded status in the busiest group finding logic
sched: Move p->nr_cpus_allowed check to select_task_rq()
sched/completion: Document when to use wait_for_completion_io_*()
sched: Update comments about CLONE_NEWUTS and CLONE_NEWIPC
sched/fair: Kill task_struct::numa_entry and numa_group::task_list
sched: Refactor task_struct to use numa_faults instead of numa_* pointers
sched/deadline: Don't check CONFIG_SMP in switched_from_dl()
sched/deadline: Reschedule from switched_from_dl() after a successful pull
sched/deadline: Push task away if the deadline is equal to curr during wakeup
sched/deadline: Add deadline rq status print
sched/deadline: Fix artificial overrun introduced by yield_task_dl()
sched/rt: Clean up check_preempt_equal_prio()
sched/core: Use dl_bw_of() under rcu_read_lock_sched()
sched: Check if we got a shallowest_idle_cpu before searching for least_loaded_cpu
...
Remove use of 'swdev' mode in rocker. rocker dev offloads
can use the BRIDGE_FLAGS_SELF to indicate offload to hardware.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
the queue length of sd->input_pkt_queue has been put into qlen,
and impossible to change, since hold the lock
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
... making both non-draining. That means that tcp_recvmsg() becomes
non-draining. And _that_ would break iscsit_do_rx_data() unless we
a) make sure tcp_recvmsg() is uniformly non-draining (it is)
b) make sure it copes with arbitrary (including shifted)
iov_iter (it does, all it uses is iov_iter primitives)
c) make iscsit_do_rx_data() initialize ->msg_iter only once.
Fortunately, (c) is doable with minimal work and we are rid of one
the two places where kernel send/recvmsg users would be unhappy with
non-draining behaviour.
Actually, that makes all but one of ->recvmsg() instances iov_iter-clean.
The exception is skcipher_recvmsg() and it also isn't hard to convert
to primitives (iov_iter_get_pages() is needed there). That'll wait
a bit - there's some interplay with ->sendmsg() path for that one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since commit f886497212 ("ipv4: fix dst race in sk_dst_get()")
DST_NOCACHE dst_entries get freed by RCU. So there is no need to get a
reference on them when we are in rcu protected sections.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ce1a4ea3f1 ("net: avoid one atomic operation in skb_clone()")
took the wrong way to save one atomic operation.
It is actually possible to avoid two atomic operations, if we
do not change skb->fclone values, and only rely on clone_ref
content to signal if the clone is available or not.
skb_clone() can simply use the fast clone if clone_ref is 1.
kfree_skbmem() can avoid the atomic_dec_and_test() if clone_ref is 1.
Note that because we usually free the clone before the original skb,
this particular attempt is only done for the original skb to have better
branch prediction.
SKB_FCLONE_FREE is removed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Chris Mason <clm@fb.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 56bfa7ee7c ("unregister_netdevice : move RTM_DELLINK to
until after ndo_uninit") tried to do this ealier but while doing so
it created a problem. Unfortunately the delayed rtmsg_ifinfo() also
delayed call to fill_info(). So this translated into asking driver
to remove private state and then query it's private state. This
could have catastropic consequences.
This change breaks the rtmsg_ifinfo() into two parts - one takes the
precise snapshot of the device by called fill_info() before calling
the ndo_uninit() and the second part sends the notification using
collected snapshot.
It was brought to notice when last link is deleted from an ipvlan device
when it has free-ed the port and the subsequent .fill_info() call is
trying to get the info from the port.
kernel: [ 255.139429] ------------[ cut here ]------------
kernel: [ 255.139439] WARNING: CPU: 12 PID: 11173 at net/core/rtnetlink.c:2238 rtmsg_ifinfo+0x100/0x110()
kernel: [ 255.139493] Modules linked in: ipvlan bonding w1_therm ds2482 wire cdc_acm ehci_pci ehci_hcd i2c_dev i2c_i801 i2c_core msr cpuid bnx2x ptp pps_core mdio libcrc32c
kernel: [ 255.139513] CPU: 12 PID: 11173 Comm: ip Not tainted 3.18.0-smp-DEV #167
kernel: [ 255.139514] Hardware name: Intel RML,PCH/Ibis_QC_18, BIOS 1.0.10 05/15/2012
kernel: [ 255.139515] 0000000000000009 ffff880851b6b828 ffffffff815d87f4 00000000000000e0
kernel: [ 255.139516] 0000000000000000 ffff880851b6b868 ffffffff8109c29c 0000000000000000
kernel: [ 255.139518] 00000000ffffffa6 00000000000000d0 ffffffff81aaf580 0000000000000011
kernel: [ 255.139520] Call Trace:
kernel: [ 255.139527] [<ffffffff815d87f4>] dump_stack+0x46/0x58
kernel: [ 255.139531] [<ffffffff8109c29c>] warn_slowpath_common+0x8c/0xc0
kernel: [ 255.139540] [<ffffffff8109c2ea>] warn_slowpath_null+0x1a/0x20
kernel: [ 255.139544] [<ffffffff8150d570>] rtmsg_ifinfo+0x100/0x110
kernel: [ 255.139547] [<ffffffff814f78b5>] rollback_registered_many+0x1d5/0x2d0
kernel: [ 255.139549] [<ffffffff814f79cf>] unregister_netdevice_many+0x1f/0xb0
kernel: [ 255.139551] [<ffffffff8150acab>] rtnl_dellink+0xbb/0x110
kernel: [ 255.139553] [<ffffffff8150da90>] rtnetlink_rcv_msg+0xa0/0x240
kernel: [ 255.139557] [<ffffffff81329283>] ? rhashtable_lookup_compare+0x43/0x80
kernel: [ 255.139558] [<ffffffff8150d9f0>] ? __rtnl_unlock+0x20/0x20
kernel: [ 255.139562] [<ffffffff8152cb11>] netlink_rcv_skb+0xb1/0xc0
kernel: [ 255.139563] [<ffffffff8150a495>] rtnetlink_rcv+0x25/0x40
kernel: [ 255.139565] [<ffffffff8152c398>] netlink_unicast+0x178/0x230
kernel: [ 255.139567] [<ffffffff8152c75f>] netlink_sendmsg+0x30f/0x420
kernel: [ 255.139571] [<ffffffff814e0b0c>] sock_sendmsg+0x9c/0xd0
kernel: [ 255.139575] [<ffffffff811d1d7f>] ? rw_copy_check_uvector+0x6f/0x130
kernel: [ 255.139577] [<ffffffff814e11c9>] ? copy_msghdr_from_user+0x139/0x1b0
kernel: [ 255.139578] [<ffffffff814e1774>] ___sys_sendmsg+0x304/0x310
kernel: [ 255.139581] [<ffffffff81198723>] ? handle_mm_fault+0xca3/0xde0
kernel: [ 255.139585] [<ffffffff811ebc4c>] ? destroy_inode+0x3c/0x70
kernel: [ 255.139589] [<ffffffff8108e6ec>] ? __do_page_fault+0x20c/0x500
kernel: [ 255.139597] [<ffffffff811e8336>] ? dput+0xb6/0x190
kernel: [ 255.139606] [<ffffffff811f05f6>] ? mntput+0x26/0x40
kernel: [ 255.139611] [<ffffffff811d2b94>] ? __fput+0x174/0x1e0
kernel: [ 255.139613] [<ffffffff814e2129>] __sys_sendmsg+0x49/0x90
kernel: [ 255.139615] [<ffffffff814e2182>] SyS_sendmsg+0x12/0x20
kernel: [ 255.139617] [<ffffffff815df092>] system_call_fastpath+0x12/0x17
kernel: [ 255.139619] ---[ end trace 5e6703e87d984f6b ]---
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.
It modifies drivers implementation of set/get_rxfh accordingly.
This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.
User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.
Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduce new setsockopt() command:
setsockopt(sock, SOL_SOCKET, SO_ATTACH_BPF, &prog_fd, sizeof(prog_fd))
where prog_fd was received from syscall bpf(BPF_PROG_LOAD, attr, ...)
and attr->prog_type == BPF_PROG_TYPE_SOCKET_FILTER
setsockopt() calls bpf_prog_get() which increments refcnt of the program,
so it doesn't get unloaded while socket is using the program.
The same eBPF program can be attached to multiple sockets.
User task exit automatically closes socket which calls sk_filter_uncharge()
which decrements refcnt of eBPF program
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a) make get_proc_ns() return a pointer to struct ns_common
b) mirror ns_ops in dentry->d_fsdata of ns dentries, so that
is_mnt_ns_file() could get away with fewer dereferences.
That way struct proc_ns becomes invisible outside of fs/proc/*.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
for now - just move corresponding ->proc_inum instances over there
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
To allow brport device to return current brport flags set on port. Add
returned flags to nested IFLA_PROTINFO netlink msg built in dflt getlink.
With this change, netlink msg returned for bridge_getlink contains the port's
offloaded flag settings (the port's SELF settings).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevice represents a port in a switch, it will expose
IFLA_PHYS_SWITCH_ID value via rtnl. Two netdevices with the same value
belong to one physical switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So this can be reused for identification of other "items" as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_link_get_net() holds a reference on the 'struct net', we need to release
it in case of error.
CC: Eric W. Biederman <ebiederm@xmission.com>
Fixes: b51642f6d7 ("net: Enable a userns root rtnl calls that are safe for unprivilged users")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only search for IFLA_EXT_MASK if the message actually carries a
ifinfomsg header and validate minimal length requirements for
IFLA_EXT_MASK.
Fixes: 6cbdceeb ("bridge: Dump vlan information from a bridge port")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Payload is currently accessed blindly and may exceed valid message
boundaries.
Fixes: 407af3299 ("bridge: Add netlink interface to configure vlans on bridge ports")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e1bd95bf7c ("crypto: algif - zeroize IV buffer") and
2a6af25bef ("crypto: algif - zeroize message digest buffer")
added memzero_explicit() calls on buffers that are later on
passed back to sock_kfree_s().
This is a discussed follow-up that, instead, extends the sock
API and adds sock_kzfree_s(), which internally uses kzfree()
instead of kfree() for passing the buffers back to slab.
Having sock_kzfree_s() allows to keep the changes more minimal
by just having a drop-in replacement instead of adding
memzero_explicit() calls everywhere before sock_kfree_s().
In kzfree(), the compiler is not allowed to optimize the memset()
away and thus there's no need for memzero_explicit(). Both,
sock_kfree_s() and sock_kzfree_s() are wrappers for
__sock_kfree_s() and call into kfree() resp. kzfree(); here,
__sock_kfree_s() needs to be explicitly inlined as we want the
compiler to optimize the call and condition away and thus it
produces e.g. on x86_64 the _same_ assembler output for
sock_kfree_s() before and after, and thus also allows for
avoiding code duplication.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
Not sure what I was thinking, but doing anything after
releasing a refcount is suicidal or/and embarrassing.
By the time we set skb->fclone to SKB_FCLONE_FREE, another cpu
could have released last reference and freed whole skb.
We potentially corrupt memory or trap if CONFIG_DEBUG_PAGEALLOC is set.
Reported-by: Chris Mason <clm@fb.com>
Fixes: ce1a4ea3f1 ("net: avoid one atomic operation in skb_clone()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
So it can be used from out of openvswitch code.
Did couple of cosmetic changes on the way, namely variable naming and
adding support for 8021AD proto.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
note that skb_make_writable already exists in net/netfilter/core.c
but does something slightly different.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use them to push skb->vlan_tci into the payload and avoid code
duplication.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name fits better. Plus there's going to be introduced
__vlan_insert_tag later on.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use {compat_,}rw_copy_check_uvector(). As the result, we are
guaranteed that all iovecs seen in ->msg_iov by ->sendmsg()
and ->recvmsg() will pass access_ok().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The proc_remove() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS (Receive Side Scaling) typically uses Toeplitz hash and a 40 or 52 bytes
RSS key.
Some drivers use a constant (and well known key), some drivers use a random
key per port, making bonding setups hard to tune. Well known keys increase
attack surface, considering that number of queues is usually a power of two.
This patch provides infrastructure to help drivers doing the right thing.
netdev_rss_key_fill() should be used by drivers to initialize their RSS key,
even if they provide ethtool -X support to let user redefine the key later.
A new /proc/sys/net/core/netdev_rss_key file can be used to get the host
RSS key even for drivers not providing ethtool -x support, in case some
applications want to precisely setup flows to match some RX queues.
Tested:
myhost:~# cat /proc/sys/net/core/netdev_rss_key
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41:36:40:74:b6:15:ca:27:44:aa:b3:4d:72
myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
0: 0 1 2 3 4 5 6 7
RSS hash key:
11:63:99:bb:79:fb:a5:a7:07:45:b2:20:bf:02:42:2d:08:1a:dd:19:2b:6b:23:ac:56:28:9d:70:c3:ac:e8:16:4b:b7:c1:10:53:a4:78:41
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Large receive offloading is known to cause problems if received packets
are passed to other host. Therefore the kernel disables it by calling
dev_disable_lro() whenever a network device is enslaved in a bridge or
forwarding is enabled for it (or globally). For virtual devices we need
to disable LRO on the underlying physical device (which is actually
receiving the packets).
Current dev_disable_lro() code handles this propagation for a vlan
(including 802.1ad nested vlan), macvlan or a vlan on top of a macvlan.
It doesn't handle other stacked devices and their combinations, in
particular propagation from a bond to its slaves which often causes
problems in virtualization setups.
As we now have generic data structures describing the upper-lower device
relationship, dev_disable_lro() can be generalized to disable LRO also
for all lower devices (if any) once it is disabled for the device
itself.
For bonding and teaming devices, it is necessary to disable LRO not only
on current slaves at the moment when dev_disable_lro() is called but
also on any slave (port) added later.
v2: use lower device links for all devices (including vlan and macvlan)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are only three neigh tables in the whole kernel:
arp table, ndisc table and decnet neigh table. What's more,
we don't support registering multiple tables per family.
Therefore we can just make these tables statically built-in.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more common dynamic_debug capable net_dbg_ratelimited
and remove the LIMIT_NETDEBUG macro.
All messages are still ratelimited.
Some KERN_<LEVEL> uses are changed to KERN_DEBUG.
This may have some negative impact on messages that were
emitted at KERN_INFO that are not not enabled at all unless
DEBUG is defined or dynamic_debug is enabled. Even so,
these messages are now _not_ emitted by default.
This also eliminates the use of the net_msg_warn sysctl
"/proc/sys/net/core/warnings". For backward compatibility,
the sysctl is not removed, but it has no function. The extern
declaration of net_msg_warn is removed from sock.h and made
static in net/core/sysctl_net_core.c
Miscellanea:
o Update the sysctl documentation
o Remove the embedded uses of pr_fmt
o Coalesce format fragments
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alternative to RPS/RFS is to use hardware support for multiple
queues.
Then split a set of million of sockets into worker threads, each
one using epoll() to manage events on its own socket pool.
Ideally, we want one thread per RX/TX queue/cpu, but we have no way to
know after accept() or connect() on which queue/cpu a socket is managed.
We normally use one cpu per RX queue (IRQ smp_affinity being properly
set), so remembering on socket structure which cpu delivered last packet
is enough to solve the problem.
After accept(), connect(), or even file descriptor passing around
processes, applications can use :
int cpu;
socklen_t len = sizeof(cpu);
getsockopt(fd, SOL_SOCKET, SO_INCOMING_CPU, &cpu, &len);
And use this information to put the socket into the right silo
for optimal performance, as all networking stack should run
on the appropriate cpu, without need to send IPI (RPS/RFS).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuning coalescing parameters on NIC can be really hard.
Servers can handle both bulk and RPC like traffic, with conflicting
goals : bulk flows want as big GRO packets as possible, RPC want minimal
latencies.
To reach big GRO packets on 10Gbe NIC, one can use :
ethtool -C eth0 rx-usecs 4 rx-frames 44
But this penalizes rpc sessions, with an increase of latencies, up to
50% in some cases, as NICs generally do not force an interrupt when
a packet with TCP Push flag is received.
Some NICs do not have an absolute timer, only a timer rearmed for every
incoming packet.
This patch uses a different strategy : Let GRO stack decides what do do,
based on traffic pattern.
Packets with Push flag wont be delayed.
Packets without Push flag might be held in GRO engine, if we keep
receiving data.
This new mechanism is off by default, and shall be enabled by setting
/sys/class/net/ethX/gro_flush_timeout to a value in nanosecond.
To fully enable this mechanism, drivers should use napi_complete_done()
instead of napi_complete().
Tested:
Ran 200 netperf TCP_STREAM from A to B (10Gbe mlx4 link, 8 RX queues)
Without this feature, we send back about 305,000 ACK per second.
GRO aggregation ratio is low (811/305 = 2.65 segments per GRO packet)
Setting a timer of 2000 nsec is enough to increase GRO packet sizes
and reduce number of ACK packets. (811/19.2 = 42)
Receiver performs less calls to upper stacks, less wakes up.
This also reduces cpu usage on the sender, as it receives less ACK
packets.
Note that reducing number of wakes up increases cpu efficiency, but can
decrease QPS, as applications wont have the chance to warmup cpu caches
doing a partial read of RPC requests/answers if they fit in one skb.
B:~# sar -n DEV 1 10 | grep eth0 | tail -1
Average: eth0 811269.80 305732.30 1199462.57 19705.72 0.00
0.00 0.50
B:~# echo 2000 >/sys/class/net/eth0/gro_flush_timeout
B:~# sar -n DEV 1 10 | grep eth0 | tail -1
Average: eth0 811577.30 19230.80 1199916.51 1239.80 0.00
0.00 0.50
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that both macvtap and tun are using skb_copy_datagram_iter, we
can kill the abomination that is skb_copy_datagram_const_iovec.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds skb_copy_datagram_iter, which is identical to
skb_copy_datagram_iovec except that it operates on iov_iter
instead of iovec.
Eventually all users of skb_copy_datagram_iovec should switch
over to iov_iter and then we can remove skb_copy_datagram_iovec.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow datapath to recognize and extract MPLS labels into flow keys
and execute actions which push, pop, and set labels on packets.
Based heavily on work by Leo Alterman, Ravi K, Isaku Yamahata and Joe Stringer.
Cc: Ravi K <rkerur@gmail.com>
Cc: Leo Alterman <lalterman@nicira.com>
Cc: Isaku Yamahata <yamahata@valinux.co.jp>
Cc: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Device can export MPLS GSO support in dev->mpls_features same way
it export vlan features in dev->vlan_features. So it is safe to
remove NETIF_F_GSO_MPLS redundant flag.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
This encapsulates all of the skb_copy_datagram_iovec() callers
with call argument signature "skb, offset, msghdr->msg_iov, length".
When we move to iov_iters in the networking, the iov_iter object will
sit in the msghdr.
Having a helper like this means there will be less places to touch
during that transformation.
Based upon descriptions and patch from Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new GSO type, SKB_GSO_TUNNEL_REMCSUM, which indicates remote
checksum offload being done (in this case inner checksum must not
be offloaded to the NIC).
Added logic in __skb_udp_tunnel_segment to handle remote checksum
offload case.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_lock_unregistering*() take rtnl_lock() -- a mutex -- inside a
wait loop. The wait loop relies on current->state to function, but so
does mutex_lock(), nesting them makes for the inner to destroy the
outer state.
Fix this using the new wait_woken() bits.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Cong Wang <cwang@twopensource.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: sfeldma@cumulusnetworks.com <sfeldma@cumulusnetworks.com>
Cc: stephen hemminger <stephen@networkplumber.org>
Cc: Tom Gundersen <teg@jklm.no>
Cc: Tom Herbert <therbert@google.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/20141029173110.GE15602@worktop.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
net_rx_action() can mask irqs a single time to transfert sd->poll_list
into a private list, for a very short duration.
Then, napi_complete() can avoid masking irqs again,
and net_rx_action() only needs to mask irq again in slow path.
This patch removes 2 couples of irq mask/unmask per typical NAPI run,
more if multiple napi were triggered.
Note this also allows to give control back to caller (do_softirq())
more often, so that other softirq handlers can be called a bit earlier,
or ksoftirqd can be wakeup earlier under pressure.
This was developed while testing an alternative to RX interrupt
mitigation to reduce latencies while keeping or improving GRO
aggregation on fast NIC.
Idea is to test napi->gro_list at the end of a napi->poll() and
reschedule one NAPI poll, but after servicing a full round of
softirqs (timers, TX, rcu, ...). This will be allowed only if softirq
is currently serviced by idle task or ksoftirqd, and resched not needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a driver supports reading EEPROM but no EEPROM is installed in the system,
the driver's get_eeprom_len function returns 0. ethtool will subsequently
try to read that zero-length EEPROM anyway. If the driver does not support
EEPROM access at all, this operation will return -EOPNOTSUPP. If the driver
does support EEPROM access but no EEPROM is installed, the operation will
return -EINVAL. Return -EOPNOTSUPP in both cases for consistency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In neigh_parms_release() we loop over all entries to find the entry given in
argument and being able to remove it from the list. By using a double linked
list, we can avoid this loop.
Here are some numbers with 30 000 dummy interfaces configured:
Before the patch:
$ time rmmod dummy
real 2m0.118s
user 0m0.000s
sys 1m50.048s
After the patch:
$ time rmmod dummy
real 1m9.970s
user 0m0.000s
sys 0m47.976s
Suggested-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_schedule() can be called from any context and has to mask hard
irqs.
Add a variant that can only be called from hard interrupts handlers
or when irqs are already masked.
Many NIC drivers can use it from their hard IRQ handler instead of
generic variant.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generalizes commit d6a4a10411 ("tcp: GSO should be TSQ
friendly") to protocols using skb_set_owner_w()
TCP uses its own destructor (tcp_wfree) and needs a more complex scheme
as explained in commit 6ff50cd555 ("tcp: gso: do not generate out of
order packets")
This allows UDP sockets using UFO to get proper backpressure,
thus avoiding qdisc drops and excessive cpu usage.
Here are performance test results (macvlan on vlan):
- Before
# netperf -t UDP_STREAM ...
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 65507 60.00 144096 1224195 1258.56
212992 60.00 51 0.45
Average: CPU %user %nice %system %iowait %steal %idle
Average: all 0.23 0.00 25.26 0.08 0.00 74.43
- After
# netperf -t UDP_STREAM ...
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 65507 60.00 109593 0 957.20
212992 60.00 109593 957.20
Average: CPU %user %nice %system %iowait %steal %idle
Average: all 0.18 0.00 8.38 0.02 0.00 91.43
[edumazet] Rewrote patch and changelog.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not reuse skb if it was pfmemalloc tainted, otherwise
future frame might be dropped anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The crafted header start address is from a driver supplied buffer, which
one can reasonably expect to be aligned on a 4-bytes boundary.
However ATM the TSO helper API is only used by ethernet drivers and
the tcp header will then be aligned to a 2-bytes only boundary from the
header start address.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if ->encapsulation is set we have to use inner_tcp_hdrlen and add the
size of the inner network headers too.
This is 'mostly harmless'; tbf might send skb that is slightly over
quota or drop skb even if it would have fit.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Include fixes for netrom and dsa (Fabian Frederick and Florian
Fainelli)
2) Fix FIXED_PHY support in stmmac, from Giuseppe CAVALLARO.
3) Several SKB use after free fixes (vxlan, openvswitch, vxlan,
ip_tunnel, fou), from Li ROngQing.
4) fec driver PTP support fixes from Luwei Zhou and Nimrod Andy.
5) Use after free in virtio_net, from Michael S Tsirkin.
6) Fix flow mask handling for megaflows in openvswitch, from Pravin B
Shelar.
7) ISDN gigaset and capi bug fixes from Tilman Schmidt.
8) Fix route leak in ip_send_unicast_reply(), from Vasily Averin.
9) Fix two eBPF JIT bugs on x86, from Alexei Starovoitov.
10) TCP_SKB_CB() reorganization caused a few regressions, fixed by Cong
Wang and Eric Dumazet.
11) Don't overwrite end of SKB when parsing malformed sctp ASCONF
chunks, from Daniel Borkmann.
12) Don't call sock_kfree_s() with NULL pointers, this function also has
the side effect of adjusting the socket memory usage. From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
bna: fix skb->truesize underestimation
net: dsa: add includes for ethtool and phy_fixed definitions
openvswitch: Set flow-key members.
netrom: use linux/uaccess.h
dsa: Fix conversion from host device to mii bus
tipc: fix bug in bundled buffer reception
ipv6: introduce tcp_v6_iif()
sfc: add support for skb->xmit_more
r8152: return -EBUSY for runtime suspend
ipv4: fix a potential use after free in fou.c
ipv4: fix a potential use after free in ip_tunnel_core.c
hyperv: Add handling of IP header with option field in netvsc_set_hash()
openvswitch: Create right mask with disabled megaflows
vxlan: fix a free after use
openvswitch: fix a use after free
ipv4: dst_entry leak in ip_send_unicast_reply()
ipv4: clean up cookie_v4_check()
ipv4: share tcp_v4_save_options() with cookie_v4_check()
ipv4: call __ip_options_echo() in cookie_v4_check()
atm: simplify lanai.c by using module_pci_driver
...
Add ndo_gso_check which a device can define to indicate whether is
is capable of doing GSO on a packet. This funciton would be called from
the stack to determine whether software GSO is needed to be done. A
driver should populate this function if it advertises GSO types for
which there are combinations that it wouldn't be able to handle. For
instance a device that performs UDP tunneling might only implement
support for transparent Ethernet bridging type of inner packets
or might have limitations on lengths of inner headers.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
Unlike normal kfree() it is never right to call sock_kfree_s() with
a NULL pointer, because sock_kfree_s() also has the side effect of
discharging the memory from the sockets quota.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is illegal to use atomic_set(&page->_count, ...) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
The only case it is valid is when page->_count is 0
Fixes: 540eb7bf0b ("net: Update alloc frag to reduce get/put page usage and recycle pages")
Signed-off-by: Eric Dumaze <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a kernel unaligned access bug seen on a sparc64 system
with an igb adapter. Specifically the __skb_flow_get_ports was returning a
be32 pointer which was then having the value directly returned.
In order to prevent this it is actually easier to simply not populate the
ports or address values when an skb is not present. In this case the
assumption is that the data isn't needed and rather than slow down the
faster aligned accesses by making them have to assume the unaligned path on
architectures that don't support efficent unaligned access it makes more
sense to simply switch off the bits that were copying the source and
destination address/port for the case where we only care about the protocol
types and lengths which are normally 16 bit fields anyway.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. sk_run_filter has been renamed, sk_filter() is using SK_RUN_FILTER.
2. Remove wrong comments about storing intermediate value.
3. replace sk_run_filter with __bpf_prog_run for check_load_and_stores's
comments
Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix following warning.
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'header_len'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'data_len'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'max_page_order'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'errcode'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'gfp_mask'
Acutually the descriptions exist, but missing "@" in front.
This problem start to happen when following commit was merged
into Linus's tree during 3.18-rc1 merge period.
commit 2e4e441071
net: add alloc_skb_with_frags() helper
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
1/ Step down as dmaengine maintainer see commit 08223d80df "dmaengine
maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13 (commit
7787380336 "net_dma: mark broken"), without reports of performance
regression.
3/ Miscellaneous fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BBBv
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine updates from Dan Williams:
"Even though this has fixes marked for -stable, given the size and the
needed conflict resolutions this is 3.18-rc1/merge-window material.
These patches have been languishing in my tree for a long while. The
fact that I do not have the time to do proper/prompt maintenance of
this tree is a primary factor in the decision to step down as
dmaengine maintainer. That and the fact that the bulk of drivers/dma/
activity is going through Vinod these days.
The net_dma removal has not been in -next. It has developed simple
conflicts against mainline and net-next (for-3.18).
Continuing thanks to Vinod for staying on top of drivers/dma/.
Summary:
1/ Step down as dmaengine maintainer see commit 08223d80df
"dmaengine maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13
(commit 7787380336 "net_dma: mark broken"), without reports of
performance regression.
3/ Miscellaneous fixes"
* tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
net: make tcp_cleanup_rbuf private
net_dma: revert 'copied_early'
net_dma: simple removal
dmaengine maintainer update
dmatest: prevent memory leakage on error path in thread
ioat: Use time_before_jiffies()
dmaengine: fix xor sources continuation
dma: mv_xor: Rename __mv_xor_slot_cleanup() to mv_xor_slot_cleanup()
dma: mv_xor: Remove all callers of mv_xor_slot_cleanup()
dma: mv_xor: Remove unneeded mv_xor_clean_completed_slots() call
ioat: Use pci_enable_msix_exact() instead of pci_enable_msix()
drivers: dma: Include appropriate header file in dca.c
drivers: dma: Mark functions as static in dma_v3.c
dma: mv_xor: Add DMA API error checks
ioat/dca: Use dev_is_pci() to check whether it is pci device
Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.
Current handling of IFF_XMIT_DST_RELEASE is not optimal.
Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y
The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.
As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.
This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.
Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :
dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
netif_keep_dst(dev);
Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.
The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probably not a big deal, but we'd better just use the
one we get in retry loop.
Fixes: commit 22e0f8b932 ("net: sched: make bstats per cpu and estimator RCU safe")
Reported-by: Joe Perches <joe@perches.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marking this as static allows compiler to inline it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some TSO engines might have a too heavy setup cost, that impacts
performance on hosts sending small bursts (2 MSS per packet).
This patch adds a device gso_min_segs, allowing drivers to set
a minimum segment size for TSO packets, according to the NIC
performance.
Tested on a mlx4 NIC, this allows to get a ~110% increase of
throughput when sending 2 MSS per packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
