The current channel switch code has a potential deadlock:
1) * cfg80211_stop_ap acquires wdev-lock
* ieee80211_stop_ap calls cancel_work_sync for the csa_finalize_work,
which acquires the associated worker-lock
2) * ieee80211_csa_finalize_work holds the worker-lock when run
* it calls cfg80211_ch_switch_notify which will claim the wdev-lock,
and also needs to claim the sdata-lock (which is the same as the
wdev-lock) to modify the beacons.
It is sufficient to just set the channel switch active to false. If the
worker is running later, it will find the channel switch to not be
active anymore and returns immediately without changing anything.
Canceling the worker is done anyway when the interface goes down
(ieee80211_do_stop).
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch notification should be sent under the
wdev/sdata-lock, preferably in the same moment as the channel change
happens, to avoid races by other callers (e.g. start/stop_ap).
This also adds the previously missing sdata_lock protection in
csa_finalize_work.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa finalize worker needs to change the beacon information (for
different modes). These are normally protected under rtnl lock, but the
csa finalize worker is called by drivers and should not acquire the RTNL
lock. Therefore change access protection for beacons to sdata/wdev lock.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[fix sdata_dereference]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no reason why we should have only one channel switch
announcement at a time for a single phy. When support for channel
switch with multiple contexts and multiple vifs per context is
implemented, we will need the chandef data for each vif. Move the
csa_chandef structure to sdata to prepare for this.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[Fixed compilation with mesh]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use put_unaligned_le16 in mesh_plink_frame_tx.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds generic cipher scheme support to mac80211, such schemes
are fully under control by the driver. On hw registration drivers
may specify additional HW ciphers with a scheme how these ciphers
have to be handled by mac80211 TX/RR. A cipher scheme specifies a
cipher suite value, a size of the security header to be added to
or stripped from frames and how the PN is to be verified on RX.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To report channel width correctly we have
to send correct channel parameters from
mac80211 when calling cfg80211_cac_event().
This is required in case of using channel width
higher than 20MHz and we have to set correct
dfs channel state after CAC (NL80211_DFS_AVAILABLE).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh STA receiving the mesh CSA action frame is not able to trigger
the mesh channel switch due to the incorrect handling and comparison
of mesh channel switch parameters element (MCSP)'s TTL. Make sure
the MCSP's TTL is updated accordingly before calling the
ieee80211_mesh_process_chnswitch. Also, we update the beacon before
forwarding the CSA action frame, so MCSP's precedence value and
initiator flag need to be updated prior to this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh beacon was not being rebuild after user triggered a mesh
powersave change.
To solve this issue use ieee80211_mbss_info_change_notify instead
of ieee80211_bss_info_change_notify. This helper function forces
mesh beacon to be rebuild and then notifies the driver about the
beacon change.
Signed-off-by: Javier Lopez <jlopex@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit ee1f668136.
The aformentioned commit added a check to allow
'iw wlan0 set power_save off' to work for mesh interfaces.
However, this is problematic because it also allows
'iw wlan0 set power_save on', which will crash in short order
because all of the subsequent code manipulates sdata->u.mgd.
The power-saving states for mesh interfaces can be manipulated
through the mesh config, e.g:
'iw wlan0 set mesh_param mesh_power_save=active' (which,
despite the name, actualy disables power saving since the
setting refers to the type of sleep the interface undergoes).
Cc: stable@vger.kernel.org
Fixes: ee1f668136 ("mac80211: allow disable power save in mesh")
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CSA completion could call in a driver
bss_info_changed() with a garbled `changed` flag
leading to all sorts of problems.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the required procedures for mesh channel switching as defined
in the IEEE Std 802.11-2012 section 10.9.8.4.3 and also handle the CSA
and MCSP elements as followed:
* Add the function for updating the beacon and probe response frames
with CSA and MCSP elements during the period of switching to the new
channel. Both CSA and MCSP elements must be included in beacon and
probe response frames until the intended channel switch time.
* The ifmsh->csa_settings is set to NULL and the CSA and MCSP elements
will then be removed from the beacon or probe response frames once the
new channel is switched to.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the triggering of CSA frame using mesh interface. The
rules are more or less same with IBSS, such as not allowed to
change between the band and channel width has to be same from
the previous mode. Also, move the ieee80211_send_action_csa
to a common space so that it can be re-used by mesh interface.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes errors in the mesh powersave logic which
cause that remote peers do not get peer power mode change
notifications and mesh peer service periods (MPSPs) got
stuck.
When closing a peer link, set the (now invalid) peer-specific
power mode to 'unknown'.
Avoid overhead when local power mode is unchanged.
Reliably clear MPSP flags on peering status update.
Avoid MPSP flags getting stuck by not requesting a further
MPSP ownership if we already are an MPSP owner.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver requests to move to STATIC or DYNAMIC SMPS,
we send an action frame to each associated station and
reconfigure the channel context / driver.
Of course, non-MIMO stations are ignored.
The beacon isn't updated. The association response will
include the original capabilities. Stations that associate
while in non-OFF SMPS mode will get an action frame right
after association to inform them about our current state.
Note that we wait until the end of the EAPOL. Sending an
action frame before the EAPOL is finished can be an issue
for a few clients. Clients aren't likely to send EAPOL
frames in MIMO anyway.
When the SMPS configuration gets more permissive (e.g.
STATIC -> OFF), we don't wake up stations that are asleep
We remember that they don't know about the change and send
the action frame when they wake up.
When the SMPS configuration gets more restrictive (e.g.
OFF -> STATIC), we set the TIM bit for every sleeping STA.
uAPSD stations might send MIMO until they poll the action
frame, but this is for a short period of time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix vht streams loop, initialisation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Limit the current implementation to a single channel context used by
a single vif, thereby avoiding multi-vif/channel complexities.
Reuse the main function from AP CSA code, but move a portion out in
order to fit the STA scenario.
Add a new mac80211 HW flag so we don't break devices that don't support
channel switch with channel-contexts. The new behavior will be opt-in.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows calls for clients in AP_VLANs (e.g. for 4-addr) to succeed
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function adds the channel switch announcement implementation for the
IBSS code. It is triggered by userspace (mac80211/cfg) or by external
channel switch announcement, which have to be adopted. Both CSAs in
beacons and action frames are supported. As for AP mode, the channel
switch is applied after some time. However in IBSS mode, the channel
switch IEs are generated in the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the wdev from cfg80211 on to the driver as the vif
if given and it's valid for the driver.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To allow drivers to implement per-interface testmode operations
more easily, pass a wdev pointer if any identification for one
was given from userspace. Clean up the code a bit while at it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.
This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The various components accessing the bitrates table must use consider
the used channel bandwidth to select only available rates or calculate
the bitrate correctly.
There are some rates in reduced bandwidth modes which can't be
represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The
standard suggests to round up to the next multiple of 500kbps, just do
that in mac80211 as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
As reported in https://bugzilla.kernel.org/show_bug.cgi?id=60514,
the station loop never initialises 'sinfo' and therefore adds up
a stack values, leaking stack information (the number of times it
adds values is easily obtained another way.)
Fix this by initialising the sinfo for each station to add.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Useful for userspace mesh to authenticate and peer without
a station entry, since both steps may fail anyway.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211 to avoid conflicts with the nl80211 attrbuf
changes.
Conflicts:
net/mac80211/iface.c
net/wireless/nl80211.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 6d810f1032
In this way an IBSS station will not use the AUTH messages
to trigger a state reinitialisation anymore.
The behaviour was racy and was not working properly.
It has been introduced to help wpa_supplicant to support
IBSS/RSN, however all the logic is now getting moved into
wpa_s itself which will also be in charge of handling the
AUTH messages thanks to the mgmt frame registration.
If userspace does not register for receiving AUTH frames
then mac80211 will still reply by itself.
At the same time, the auth frame registration counter can be
removed since it is not needed anymore.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[remove unused variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a CAC is running and stop_ap is called (e.g. when hostapd is killed
while performing CAC), the CAC must be aborted immediately.
Otherwise ieee80211_stop_ap() will try to stop it when it's too late -
wdev->channel is already NULL and the abort event can not be generated.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 passes a NULL channel to mgmt_tx if the frame has
to be sent on the one currently in use by the device.
Make the implementation of mgmt_tx correctly handle this
case. Fail if offchan is required.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[fix RCU locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time it takes to see the peer link expire may differ
by a minute since sta_expire() is run once a minute as a
mesh housekeeping task.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My cfg80211/mac80211 locking unification broke the sdata
locking in ieee80211_set_power_mgmt, it needs to acquire
the lock for __ieee80211_request_smps(). Add the locking.
Reported-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support them only if the driver advertises support for them via
IEEE80211_HW_SUPPORTS_ACTIVE_MONITOR. Unlike normal monitor interfaces,
they are added to the driver, along with their MAC address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously the mesh_auth_id was disabled. Instead set the
correct mesh authentication bit based on the mesh setup.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no real difference between *array and array, but
the former confuses smatch so write it differently. The
generated code is exactly the same.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RCU docs used to state that rcu_barrier() included a wait
for an RCU grace period; however the comments for rcu_barrier()
as of commit f0a0e6f... "rcu: Clarify memory-ordering properties
of grace-period primitives" contradict this.
So add back synchronize_{rcu,net}() to where they once were,
but keep the rcu_barrier()s for the call_rcu() callbacks.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bob Copeland <bob@cozybit.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the code always copies the configured MCS mask (even if it is
set to default), but only uses it if legacy rates were also masked out.
Fix this by adding a flag that tracks whether the configured MCS mask is
set to default or not.
Optimize the code further by storing a pointer to the configured rate
mask in txrc instead of using memcpy.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When AP interface is stopped ssid_len in the BSS configuration
isn't cleared which can confuse drivers when switching modes.
Set the length to zero when stopping the AP interface.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most times that mesh_path_add() is called, it is followed by
a lookup to get the just-added mpath. We can instead just
return the new mpath in the case that we allocated one (or the
existing one if already there), so do that. Also, reorder the
code in mesh_path_add a bit so that we don't need to allocate
in the pre-existing case.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a ROC item is canceled just as it expires, the work
struct may be scheduled while it is running (and waiting
for the mutex). This results in it being run after being
freed, which obviously crashes.
To fix this don't free it when aborting is requested but
instead mark it as "to be freed", which makes the work a
no-op and allows freeing it outside.
Cc: stable@vger.kernel.org [3.6+]
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add P2P NoA settings for STA mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[fix docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a key is allocated but not really added, there's no
need to go through the entire teardown process. Also, if
adding a key fails, ieee80211_key_link() can take care of
freeing it instead of the (only) caller.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the TX bytes/packets counters race-free by keeping
them per AC so concurrent TX on queues can't cause lost
or wrong updates. This works since each station belongs
to a single interface. While at it also make the bytes
counters 64-bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Earlier mac80211 would check whether some kind of mesh
security was enabled, when the real question was "is the
MPM in userspace"?
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh station types used to refer to whether the
station was secure or nonsecure. Really the salient
information is whether it is managed by the kernel or
userspace
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since hostapd will remove keys this isn't usually
an issue, but we shouldn't leak keys to the next
BSS started on the same interface. For VLANs this
also fixes a bug, keys that aren't removed would
otherwise be leaked.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During roaming, the crypto_tx_tailroom_needed_cnt counter
will often take values 2,1,0,1,2 because first keys are
removed and then new keys are added. This is inefficient
because during the 0->1 transition, synchronize_net must
be called to avoid packet races, although typically no
packets would be flowing during that time.
To avoid that, defer the decrement (2->1, 1->0) when keys
are removed (by half a second). This means the counter
will really have the values 2,2,2,3,4 ... 2, thus never
reaching 0 and having to do the 0->1 transition.
Note that this patch entirely disregards the drivers for
which this optimisation was done to start with, for them
the key removal itself will be expensive because it has
to synchronize_net() after the counter is incremented to
remove the key from HW crypto. For them the sequence will
look like this: 0,1,0,1,0,1,0,1,0 (*) which is clearly a
lot more inefficient. This could be addressed separately,
during key removal the 0->1->0 sequence isn't necessary.
(*) it starts at 0 because HW crypto is on, then goes to
1 when HW crypto is disabled for a key, then back to
0 because the key is deleted; this happens for both
keys in the example. When new keys are added, it goes
to 1 first because they're added in software; when a
key is moved to hardware it goes back to 0
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices can handle remain on channel requests differently
based on the request type/priority. Add support to
differentiate between different ROC types, i.e., indicate that
the ROC is required for sending managment frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The station change API isn't being checked properly before
drivers are called, and as a result it is difficult to see
what should be allowed and what not.
In order to comprehensively check the API parameters parse
everything first, and then have the driver call a function
(cfg80211_check_station_change()) with the additionally
information about the kind of station that is being changed;
this allows the function to make better decisions than the
old code could.
While at it, also add a few checks, particularly in mesh
and clarify the TDLS station lifetime in documentation.
To be able to reduce a few checks, ignore any flag set bits
when the mask isn't set, they shouldn't be applied then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the ability to leave the plink_state unchanged not use a
magic -1 variable that isn't in the enum, but an explicit change
flag; reject invalid plink states or actions and move the needed
constants for plink actions to the right header file. Also
reject plink_state changes for non-mesh interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After Felix's patch it was still broken in case you
used more than just a single monitor interface. Fix
it better now.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When not using channel contexts with only monitor mode interfaces being
active, report local->monitor_chandef to userspace.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's various code with strange indentation,
questionable loop and locking constructs, etc.
The bigger change is moving the "sdata" argument
to the first argument of all functions, like all
other mac80211 functions that have one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The information of the peer's capabilities is required for the driver
to perform TDLS Peer UAPSD operations. This information of the peer is
passed by the supplicant using NL80211_CMD_SET_STATION command. This
commit enhances the function nl80211_set_station to pass this
information of the peer to the driver in case this command is used
with the TDLS peer STA.
In addition, make the HT/VHT capability configuration handled more
consistently for other STA cases (reject both instead of just HT).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the entire mesh beacon would be generated each
time the beacon timer fired. Instead generate a beacon
head and tail (so the TIM can easily be inserted when mesh
power save is on) when starting a mesh or the MBSS
parameters change.
Also add a mutex for protecting beacon updates and
preventing leaks.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.
To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.
If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.
Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.
While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Like with HT, make things a bit simpler in future patches by
passing the station to ieee80211_vht_cap_ie_to_sta_vht_cap()
instead of the vht_cap pointer. Also disable VHT here if HT
isn't supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few mesh utility functions will call
ieee80211_bss_info_change_notify(), and then the caller
might notify the driver of the same change again. Avoid
this redundancy by propagating the BSS changes and
generally calling bss_info_change_notify() once per
change.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.
Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Scans currently work by stopping the netdev tx queues but leaving the
mac80211 queues active. This stops the flow of incoming packets while
still allowing mac80211 to transmit nullfunc and probe request frames to
facilitate scanning. However, the driver may try to wake the mac80211
queues while in this state, which will also wake the netdev queues.
To prevent this, add a new queue stop reason,
IEEE80211_QUEUE_STOP_REASON_OFFCHANNEL, to be used when stopping the tx
queues for off-channel operation. This prevents the netdev queues from
waking when a driver wakes the mac80211 queues.
This also stops all frames from being transmitted, even those meant to
be sent off-channel. Add a new tx control flag,
IEEE80211_TX_CTL_OFFCHAN_TX_OK, which allows frames to be transmitted
when the queues are stopped only for the off-channel stop reason. Update
all locations transmitting off-channel frames to use this flag.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the code assigns channel contexts to VLANs
(for use by the TX/RX code) when the AP master gets
its channel context assigned. This works fine, but
in the upcoming radar detection work the VLANs don't
require a channel context (during radar detection)
and assigning one to them anyway causes issues with
locking and also inconsistencies -- a VLAN interface
that is added before radar detection would get the
channel context, while one added during it wouldn't.
Fix these issues moving the channel context copying
to a new explicit operation that will not be used
in the radar detection code.
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using 'sizeof' on array given as function argument returns
size of a pointer rather than the size of array.
Cc: stable@vger.kernel.org
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add routines to
- maintain a PS mode for each peer and a non-peer PS mode
- indicate own PS mode in transmitted frames
- track neighbor STAs power modes
- buffer frames when neighbors are in PS mode
- add TIM and Awake Window IE to beacons
- release frames in Mesh Peer Service Periods
Add local_pm to sta_info to represent the link-specific power
mode at this station towards the remote station. When a peer
link is established, use the default power mode stored in mesh
config. Update the PS status if the peering status of a neighbor
changes.
Maintain a mesh power mode for non-peer mesh STAs. Set the
non-peer power mode to active mode during peering. Authenticated
mesh peering is currently not working when either node is
configured to be in power save mode.
Indicate the current power mode in transmitted frames. Use QoS
Nulls to indicate mesh power mode transitions.
For performance reasons, calls to the function setting the frame
flags are placed in HWMP routing routines, as there the STA
pointer is already available.
Add peer_pm to sta_info to represent the peer's link-specific
power mode towards the local station. Add nonpeer_pm to
represent the peer's power mode towards all non-peer stations.
Track power modes based on received frames.
Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS
neighbor counter and group-addressed frame buffer).
Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame
buffering routines in the tx path. Update num_sta_ps to buffer
and release group-addressed frames after DTIM beacons.
Announce the awake window duration in beacons if in light or
deep sleep mode towards any peer or non-peer. Create a TIM IE
similarly to AP mode and add it to mesh beacons. Parse received
Awake Window IEs and check TIM IEs for buffered frames.
Release frames towards peers in mesh Peer Service Periods. Use
the corresponding trigger frames and monitor the MPSP status.
Append a QoS Null as trigger frame if neccessary to properly end
the MPSP. Currently, in HT channels MPSPs behave imperfectly and
show large delay spikes and frame losses.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.
Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The established peer link count is indicated in mesh beacons and
used for other internal tasks. Previously it was not updated when
authenticated peering is performed in userspace.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow mesh interface to disable the power save which is by default
turn on in certain chipset. Testing with 2 units of ZCN-1523H-5-16
featuring AR9280 chipset which have power save enabled by default.
Constant reset if the average signal of the peer mesh STA is below
-80 dBm and power save is enabled.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The following changes are invalid and should be
disallowed when a station already exists:
* supported rates changes, except for TDLS peers
* listen interval changes
* HT capability changes
Disallow them and also update a mac80211 comment
explaining how they would be racy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today, stations are added already associated. That is
inefficient if, for example, the driver has no room
for stations any more because then the station will
go through the entire auth/assoc handshake, only to
be kicked out afterwards.
To address this a bit better, at least with drivers
using the new station state callback, allow hostapd
to add stations in unauthenticated mode, just after
receiving the AUTH frame, before even replying. Thus
if there's no more space at that point, it can send
a negative auth frame back. It still needs to handle
later state transition errors though, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of calculating in ieee80211_bss_info_change_notify()
whether beaconing should be enabled or not, set it in the
correct places in the callers. This simplifies the logic in
this function at the expense of offchannel, but is also more
robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are VLANs, stopping an AP is inefficient as it
calls rcu_barrier() once for each interface (the VLANs
and the AP itself). Optimise this by moving rcu_barrier()
out of the station cleanups and calling it only once for
all interfaces combined.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When all interfaces have been removed, there can't
be any stations left over, so there's no need to
flush again. Remove this, and all code associated
with it, which also simplifies the function.
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[change to flush stations with AP flush in second loop]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the logic to fill a struct rate_info with
a STA's last RX rate is accessible only in the cfg.c.
As the RX rate calculation might be needed elsewhere,
split this out into a separate function.
Signed-off-by: Saravana <saravanad@posedge.com>
[fix various whitespace issues, reword commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the low-level driver wants to support P2P GO
powersave configuration, it must set the cfg80211
flags and mac80211 will pass the parameters to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To achieve this, limit the number of retries to
31 (instead of 255) and use the three bits that
are then free for VHT flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.
Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)
This also adds new helper functions:
- cfg80211_chandef_create to create a channel def
struct given the control channel and channel type,
- cfg80211_chandef_identical to check if two channel
definitions are identical
- cfg80211_chandef_compatible to check if the given
channel definitions are compatible, and return the
wider of the two
This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
- regulatory checks on the usable bandwidth (if that
even makes sense)
- regulatory TX power (database can't deal with it)
- a proper channel compatibility calculation for the
new channel types
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.
Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers (e.g. wl12xx) might need to know the vif
to roc on (mainly in order to configure the
rx filters correctly).
Add the vif to the op params, and update the current
users (iwlwifi) to use the new api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[fix hwsim]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This new callback can be used to tune the rate to be used to send
multicast frames.
In the current state the multicast rate can be specified on IBSS/MESH
joining only. This makes it impossible to select a custom multicast
rate when then join command is sent by an external program (e.g.
wpa_supplicant)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers are not expected to handle it before drv_start has been called. It
will be called again after an interface has been brought up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of using the pointer which can be re-used
fairly quickly due to allocator patterns and then
makes debugging difficult, maintain a counter and
use its value. Since it's a 64-bit value it can't
really wrap, but catch that case anyway since it
most likely points to a bug somewhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.
Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.
Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, a lot of setup may be
necessary to start operating as an AP, some of
which may fail. Add an explicit AP start driver
method to make such failures easier to handle,
and add an AP stop driver method for symmetry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since cfg80211 will now call the explicit stop_ap
operation when an AP interface goes down, move all
teardown code there and remove it from interface
handling. The only thing that needs to stay is the
code to dev_close() all dependent VLANs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user wants to scan using a vif configured as AP,
cfg80211 must give him a chance to do it, even if this
will disrupt the stations performance due to off-channel
scanning. To do so, this patch adds a 'force' flag to the
SCAN_TRIGGER command which tells cfg80211 to perform the
scanning operation even if the vif is an AP and the
beaconing has already started.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of unused variables that gcc
pointed out (when building with W=1) as well as
some conditions that can never be true due to
the datatypes used: unsigned values can't be
less than zero. Remove this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, channel contexts may be used or
not. If they are used, the driver must have support for
hardware scan and remain-on-channel; otherwise the driver
must not advertise support for multiple channels.
Also prohibit WDS type interfaces when channel contexts
are to be used as there's no clear definition of which
channel they use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull in mac80211.git to let the next patch apply
without conflicts, also resolving a hwsim conflict.
Conflicts:
drivers/net/wireless/mac80211_hwsim.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Various small fixes for net/mac80211/cfg.c:mpath_set_pinfo():
Initialize *pinfo before filling members in, handle MESH_PATH_RESOLVED
correctly, and remove bogus assignment; result in correct display
of FLAGS values and meaningful EXPTIME for expired paths in iw utility.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit mac80211: avoid using synchronize_rcu in ieee80211_set_probe_resp
changed the return value when the probe response template is not present.
Revert to the earlier value of 1 - this fixes AP mode for drivers like
ath9k.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This could take a while (100ms+) and may delay sending assoc resp
in AP mode with WPS or P2P GO (as setting the probe resp takes place
there). We've encountered situations where the delay was big enough
to cause connection problems with devices like Galaxy Nexus.
Switch to using call_rcu with a free handler.
[Arik - rework to use plain buffer and instead of skb]
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending probe requests, e.g. during software scanning,
these will go out on the *current* channel, so their IEs
need to be built from the current channel. At other times,
e.g. for beacons or probe request templates, the IEs will
be used on the *operating* channel and using the current
channel instead might result in errors.
Add the appropriate parameters to respect the difference.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, ps mode is indicated per device (rather than
per interface), which doesn't make a lot of sense.
Moreover, there are subtle bugs caused by the inability
to indicate ps change along with other changes
(e.g. when the AP deauth us, we'd like to indicate
CHANGED_PS | CHANGED_ASSOC, as changing PS before
notifying about disassociation will result in null-packets
being sent (if IEEE80211_HW_SUPPORTS_DYNAMIC_PS) while
the sta is already disconnected.)
Keep the current per-device notifications, and add
parallel per-vif notifications.
In order to keep it simple, the per-device ps and
the per-vif ps are orthogonal - the per-vif ps
configuration is determined only by the user
configuration (enable/disable) and the connection
state, and is not affected by other vifs state and
(temporary) dynamic_ps/offchannel operations
(unlike per-device ps).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When AP interface is going down, the stations
are flushed (in ieee80211_do_stop()) only after
the beaconing was stopped.
However, drivers might rely on stations being
removed before the beaconing was stopped, in
order to clean up properly.
Fix it by flushing the stations on ap stop.
(we already do the same for other interface
types, e.g. in ieee80211_set_disassoc())
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit "mac80211: unify SW/offload remain-on-channel"
moved the cookie assignment from ieee80211_mgmt_tx()
to ieee80211_start_roc_work(). But the latter is only
called where offchannel is needed. If offchannel isn't
needed/used, a uninitialized cookie value would be returned
to userspace.
This patch sets the cookie value when offchannel isn't used.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This essentially reverts commit 2e165b8184 but
introduces the get_channel operation with a new
wireless_dev argument so that you can retrieve
the channel per interface. This is necessary as
even though we can track all interface channels
(except monitor) we can't track the channel type
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 870d37fc22.
This code doesn't work as cfg80211 will call
set_monitor_enabled at the wrong time and it
doesn't seem to be possible to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AC parameters change, drivers might rely
on getting a bss_info_changed notification with
BSS_CHANGED_QOS in addition to the conf_tx call.
Always call the function when userspace updates
are made (in AP/GO modes) and also set the change
flag when updates were made by the AP (in managed
mode.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We do not need it anymore since cfg80211 tracks
monitor channel and monitor channel type.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use cfg80211 the new .set_monitor_enabled instead
of tracking it inside mac80211.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This and ieee80211_add_ext_srates_ie() aren't
exported, so can't be used by drivers anyway,
but there's also no reason that they should be
so make them private to mac80211 and use sdata
instead of vif arguments.
Acked-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get current rssi (in dBm) from the driver/FW.
Instead of reporting the signal received in the last
rx packet, which might be inaccurate if rx traffic is
low and beacon filtering is enabled, get the signal
from the driver/FW.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a remain-on-channel item is deleted, we remove it
from the list and then start the next item. However,
if it wasn't actually the first item then calling
ieee80211_start_next_roc() is wrong as it will start
the first item -- even if that was already started.
Fix the two places that do this and add a warning to
prevent the problem from reoccurring.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Track userspace registrations for authentication
frames received on an IBSS interface. This field
will be used to decide whether or not to send
"open system" authentication frames when a new
station joins an adhoc network.
Signed-off-by: Will Hawkins <hawkinsw@opentechinstitute.org>
[redesign the code flow a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes the wrong assignment of mesh element TTL.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As defined in section 13.10.9.3 Case D (802.11-2012), this
control variable is used to limit the mesh STA to send only
one PREQ to a root mesh STA within this interval of time
(in TUs). The default value for this variable is set to
2000 TUs. However, for current implementation, the maximum
configurable of dot11MeshHWMPconfirmationInterval is
restricted by dot11MeshHWMPactivePathTimeout.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mesh_path_root_timer is invoked once the dot11MeshHWMPRootMode
is larger than 1. This patch also adds the backward compatible
to the previous setting on dot11MeshHWMPRootMode. If the user
configures as follow, it will still trigger the proactive RANN
with Gate Announcement.
iw mesh0 set mesh_param mesh_hwmp_rootmode 1
iw mesh0 set mesh_param mesh_gate_announcements 1
similar to the following setting:
iw mesh0 set mesh_param mesh_hwmp_rootmode 4
iw mesh0 set mesh_param mesh_gate_announcements 1
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the mesh configuration parameters dot11MeshHWMProotInterval
and dot11MeshHWMPactivePathToRootTimeout to be used by
proactive PREQ mechanism.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>