Add pinmux configurations for gpio matrix keypad. In this patch, only
single named mode/state is added and these pins are configured during
pinctrl driver initialization.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
In AM335x EVM tsl2550 ambient light sensor is connected to I2C2 bus.
Add child node inside i2c2 node with i2c slave address.
TAOS tsl2550 sensor is using a two-wire SMBus serial interface.
Reduce I2C2 clock frequency to 100kHz from 400kHz because the
maximum clock frequency of SMBus is 100kHz.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
[b-cousson@ti.com: Clean the changelog]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add temperature sensor DT data to am335x-evm.dts. In AM335x EVM
tmp275 temperature sensor is connected to I2C2 bus. So this patch
adds child node inside i2c2 node with i2c slave address. This patch
is tested on AM335x EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add lis331dlh device tree data to am335x-evm.dts. In AM335x EVM
lis331dlh accelerometer is connected to I2C2 bus. So this patch
change the status of I2C2 node to "okay" to use I2C2 bus. Also
added all the required platform data to am335x-evm.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add DT OPP table for AM33XX family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
Also adds cpu0 supply name to the corresponding dts files.
cpu0-supply name is used by cpufreq-cpu0 driver to get the
regulator pointer for voltage modifications.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
To make it consistent, convert all hex number presentation
to lower-case from all am33xx specific nodes.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add tps65910 regulator device tree data to AM335x-EVM by adding
regulator consumers with tightened constraints and regulator-name.
TPS65910 regulator handle can be obtained by using this regulator
name.
This patch also add I2C node with I2C frequency and tps65910 PMIC
I2C slave address.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ideally in common SoC dtsi file should set all modules
to "disabled" state and it should get enabled in respective
EVM/Board dts file as per usage.
This patch sets default status of all modules to "disabled"
state in am33xx.dtsi file. Currently there are no modules
supported as part of Bone and EVM dts support, so care
to add entry "status = "okay"" while adding support for any
module.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add AM335X EVM device tree source (am335x-evm.dts) file to
use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>