Haswell-based Fujitsu laptops (Lifebook E734/E744/E754) have a touchpad
toggle hotkey (Fn+F4) which is handled transparently to the operating
system: while an ACPI notification is sent to FUJ02B1 when Fn+F4 is
pressed, touchpad state is properly toggled without any explicit support
for this operation in fujitsu-laptop.
Skylake-based models (Lifebook E736/E746/E756) also have that hotkey,
but the touchpad is not toggled transparently to the operating system.
When Fn+F4 is pressed, an ACPI notification is sent to FUJ02E3. A
subsequent call to S000 (FUNC_RFKILL) can be used to determine whether
the touchpad toggle hotkey was pressed so that an input event can be
sent to userspace.
Relevant ACPI code:
Method (_L21, 0, NotSerialized)
{
...
If (AHKF)
{
Notify (\_SB.FEXT, 0x80)
}
...
}
Method (S000, 3, Serialized)
{
Name (_T_0, Zero)
Local0 = Zero
While (One)
{
_T_0 = Arg0
If (_T_0 == Zero)
{
Local0 |= 0x04000000
Local0 |= 0x02000000
Local0 |= 0x00020000
Local0 |= 0x0200
Local0 |= 0x0100
Local0 |= 0x20
}
ElseIf (_T_0 == One)
{
...
If (AHKF & 0x08)
{
Local0 |= 0x04000000
AHKF ^= 0x08
}
...
} ...
Break
}
Return (Local0)
}
Pressing Fn+F4 raises GPE 0x21 and sets bit 3 in AHKF. This in turn
results in bit 26 being set in the value returned by FUNC_RFKILL called
with 1 as its first argument. On Skylake-based models, bit 26 is also
set in the value returned by FUNC_RFKILL called with 0 as its first
argument (this value is saved in fujitsu_hotkey->rfkill_supported upon
module initialization), which suggests that this bit is set on models
which do not handle touchpad toggling transparently to the operating
system.
Note that bit 3 is cleared in AHKF once FUNC_RFKILL is called with 1 as
its first argument, which requires fujitsu-laptop to handle this hotkey
in a different manner than the other, GIRB-based hotkeys: two input
events (press and release) are immediately sent once Fn+F4 is pressed.
Reported-and-tested-by: Jan-Marek Glogowski <glogow@fbihome.de>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
FUJLAPTOP_* macros were introduced by 20b9373, but have never been used
except FUJLAPTOP_DEBUG, which was made redundant by the previous patch.
ACPI_VIDEO_NOTIFY_* macros were also introduced by 20b9373, but they
have not been needed since 1696d9d.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
vdbg_printk() always prefixes the log messages it generates with
"FUJ02B1", which can be misleading, because it might have been called
while handling a notify for ACPI device FUJ02E3 or during module
initialization etc. Employ pr_fmt() to prefix debug messages with the
module name instead and thus avoid confusion.
Reported-by: Jan-Marek Glogowski <glogow@fbihome.de>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Several users reported wifi cannot be unblocked as discussed in [1].
This patch removes the use of the 2009 flag by BIOS but uses the actual
WMI function calls - it will be skipped if WMI reports unsupported.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=69131
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Tested-by: Evgenii Shatokhin <eugene.shatokhin@yandex.ru>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
After several fixes, and added support for more features (WWAN,
Cooling Method and IIO accelometer axis data), bump the driver
version to 0.24.
Also update the copyright year.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Now that we have proper support for the acceleromeer under the IIO
subsystem, the _position_ sysfs file is now deprecated.
This patch removes all code related to the position sysfs entry.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch adds the accelerometer axis data to the IIO subsystem.
Currently reporting the X, Y and Z values, as no other data can be
queried given the fact that the accelerometer chip itself is hidden
behind the Toshiba proprietary interface.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Some new Dell AIO systems have a button that generates a WMI event to
turn the LCD on/off.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch reworks code for generating sparse keymap and processing WMI
events. It unifies procedure for generating sparse keymap and also unifies
big switch code for processing WMI events of different types. After this
patch dell-wmi driver does not differ between "old" and "new" hotkey type.
It constructs sparse keymap table with all WMI codes. It is because on some
laptops (e.g. Dell Latitude E6440) ACPI/firmware send both event types (old
and new).
Each WMI code in sparse keymap table is prefixed by 16bit event type, so it
does not change functionality on laptops with "old" hotkey support (those
without scancodes in DMI).
This allow us to distinguish between same WMI codes with different types in
sparse keymap. Thanks to this WMI events of type 0x0011 were moved from big
switch into sparse keymap table too.
This patch also fixes possible bug in parsing WMI event buffer introduced
in commit 5ea2559726 ("dell-wmi: Add support for new Dell systems"). That
commit changed buffer type from int* to u16* without fixing code. More at:
http://lkml.iu.edu/hypermail/linux/kernel/1507.0/01950.html
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
ACPI DSDT tables have defined other WMI codes, but does not contain any
description when those codes are emitted. Some other codes can be found in
logs on internet. In this patch are all which I saw, but lot of them are
not tested properly (e.g. for duplicate events with AT keyboard). Now we
have all WMI event codes at one place and in future after proper testing
those codes can be correctly enabled or disabled...
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
For better readability of keymap table, sort events by codes and also
update comments for events to be more informative.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
>From Dell we know that WMI event code 0xe045 is for Num Lock key, but it is
unclear due to message in commit 0b3f6109f0 ("dell-wmi: new driver for
hotkey control").
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reviewed-by: Michał Kępień <kernel@kempniu.pl>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Link: https://lkml.org/lkml/2015/7/7/830
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The whole menu depends on X86 so there is no point in repeating this
dependency on individual driver entries.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Lenovo Thinkpad devices T460, T460s, T460p, T560, X260 use
HKEY version 0x200 without adaptive keyboard.
HKEY version 0x200 has method MHKA with one parameter value.
Passing parameter value 1 will get hotkey_all_mask (the same like
HKEY version 0x100 without parameter). Passing parameter value 2 to
MHKA method will retrieve hotkey_all_adaptive_mask. If 0 is returned in
that case there is no adaptive keyboard available.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Tested-by: Lyude <cpaul@redhat.com>
Tested-by: Marco Trevisan <marco@ubuntu.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
[dvhart: Keep MHKA error string on one line in new and existing pr_err calls]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Newer ideapads support a new mic hotkey implemented via an ACPI
interface. This patch converts the mic mute event to a keycode
KEY_MICMUTE.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Acked-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
A handful of changes this merge window:
- A few patches to fix probing and configuration of pstore
- A few patches adding Elan touchpad registration on a few devices
- EC changes: a security fix dealing with max message sizes and addition
of compat_ioctl support.
- Keyboard backlight control support
There was also an accidential duplicate registration of trackpads on 'Leon',
which was reverted just recently.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXSb5tAAoJEIwa5zzehBx38BsQAI+p6urzboC2+NSsZAq72d4/
u2SF+ziEdgj4f7n38TjiDaFTqig9nqoQeB2nDCRicyEcHsCiK/ghsdq4ULfkvHIa
VALn/rBkQWQ7hC+2tfrQn7Rd2VqVnh28+EyhGezhVtrAGRaE2jIbgKnnfD3MS+b5
lab014HBppP1pDtJQQYCcoCpOUF1a9WEb8jKPWf4DCeCMaSrwFLKxV5VeqDkNtEZ
a3GFzB+WypN1nwBQ7PEOUxutzsUakSNy+RFoCqGwVppJ+kA/E3MO2BGoEJuQ6LXP
u7nyabJq6zBQAlrYie4OoiijBWQ+Q759jbOKkmxpBfL/mtMMepV05DIx/16Yi9NY
j+4A9HsuY+EYUhr0mH7B57CH0RClebixdZ62DtUK0Fe6H66SsMZPYtTKLIzOTzgO
j+gypQyW8BvcM/XjPYTA/vlYK45IJYB5OUDQzFW0qWQv/nInoYOS3G8IVooKHMDy
+s2wih/OAxBCDJ+KfDeJUj3U5Avz1YCojRraZWmBsOPpRpsQHVQ02r3uoHeHHZFv
bI8sTJ7BGxoYX5Kb6+xbtW7SnXoWZN8vlqdCpdNnLWKcwIqHKFirkoZh2N2AqyZB
7VpQW1HD2WxYBpxMv98KVyPiR+5xCnZnpqcIIvpGrX00KhmJkMgIT4FbWHMf6vVt
T55Sz5V9z/dsgMSDT3LY
=bcc4
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson
"A handful of Chrome driver and binding changes this merge window:
- a few patches to fix probing and configuration of pstore
- a few patches adding Elan touchpad registration on a few devices
- EC changes: a security fix dealing with max message sizes and
addition of compat_ioctl support.
- keyboard backlight control support
There was also an accidential duplicate registration of trackpads on
'Leon', which was reverted just recently"
* tag 'chrome-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
Revert "platform/chrome: chromeos_laptop: Add Leon Touch"
platform/chrome: chromeos_laptop - Add Elan touchpad for Wolf
platform/chrome: chromeos_laptop - Add elan trackpad option for C720
platform/chrome: cros_ec_dev - Populate compat_ioctl
platform/chrome: cros_ec_lightbar - use name instead of ID to hide lightbar attributes
platform/chrome: cros_ec_dev - Fix security issue
platform/chrome: Add Chrome OS keyboard backlight LEDs support
platform/chrome: use to_platform_device()
platform/chrome: pstore: Move to larger record size.
platform/chrome: pstore: probe for ramoops buffer using acpi
platform/chrome: chromeos_laptop: Add Leon Touch
This reverts commit bff3c624dc.
Board "Leon" is otherwise known as "Toshiba CB35" and we already have
the entry that supports that board as of this commit :
963cb6f platform/chrome: chromeos_laptop - Add Toshiba CB35 Touch
Remove this duplicate.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Mostly minor updates and cleanups. One new power management controller driver
for Intel Core SoCs.
platform/x86:
- Add PMC Driver for Intel Core SoC
dell-rbtn:
- Ignore ACPI notifications if device is suspended
thinkpad_acpi:
- save kbdlight state on suspend and restore it on resume
intel_menlow:
- reduce code duplication
asus-wmi:
- provide access to ALS control
ideapad-laptop:
- add a new WMI string for ESC key
surfacepro3_button:
- Add a warning when switching to tablet mode
sony-laptop:
- Avoid oops on module unload for older laptops
intel_telemetry:
- Constify telemetry_core_ops structures
fujitsu-laptop:
- Use IS_ENABLED() instead of checking for built-in or module
asus-laptop:
- correct error handling in sysfs_acpi_set
- remove redundant initializers
- correct error handling in asus_read_brightness()
fujitsu-laptop:
- Support radio LED
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXSJh4AAoJEKbMaAwKp3647kkIAIRi8inUCfPQsvpi7iEfaAW7
vaLvIOFfRxu+WHzYOrhrAg17yscA18xTRtp32dhjHF3w6zJsbsZ9nEqCcRliQG2+
/i6EdC1ZnboyWWW82HbFGK8r5PMpPJa2p7wPhrEuPcM3aak+bWfCD96HdjFsoxfT
Vda/2L9grvQwcUczRARh4k6sHQTsdV+tU5MF5Kefso1l31qMyO8A3PNgCPFWtCht
St0hlRs4SnZS97Bw7IIbP93AiLBejT1jtRHddvpEnj7GaPaBMpBSUqN3KgZRVnfL
Bln3iPkq+1TVprcizt60X++czfOAWmce1jF9D4oVS5FGW0yIoog0aik2H1rrY64=
=m/0/
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.7-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Mostly minor updates and cleanups. One new power management
controller driver for Intel Core SoCs.
platform/x86:
- Add PMC Driver for Intel Core SoC
dell-rbtn:
- Ignore ACPI notifications if device is suspended
thinkpad_acpi:
- save kbdlight state on suspend and restore it on resume
intel_menlow:
- reduce code duplication
asus-wmi:
- provide access to ALS control
ideapad-laptop:
- add a new WMI string for ESC key
surfacepro3_button:
- Add a warning when switching to tablet mode
sony-laptop:
- Avoid oops on module unload for older laptops
intel_telemetry:
- Constify telemetry_core_ops structures
fujitsu-laptop:
- Use IS_ENABLED() instead of checking for built-in or module
asus-laptop:
- correct error handling in sysfs_acpi_set
- remove redundant initializers
- correct error handling in asus_read_brightness()
fujitsu-laptop:
- Support radio LED"
* tag 'platform-drivers-x86-v4.7-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: Add PMC Driver for Intel Core SoC
dell-rbtn: Ignore ACPI notifications if device is suspended
thinkpad_acpi: save kbdlight state on suspend and restore it on resume
intel_menlow: reduce code duplication
asus-wmi: provide access to ALS control
ideapad-laptop: add a new WMI string for ESC key
surfacepro3_button: Add a warning when switching to tablet mode
sony-laptop: Avoid oops on module unload for older laptops
intel_telemetry: Constify telemetry_core_ops structures
fujitsu-laptop: Use IS_ENABLED() instead of checking for built-in or module
asus-laptop: correct error handling in sysfs_acpi_set
asus-laptop: remove redundant initializers
asus-laptop: correct error handling in asus_read_brightness()
fujitsu-laptop: Support radio LED
This patch adds the Power Management Controller driver as a PCI driver
for Intel Core SoC architecture.
This driver can utilize debugging capabilities and supported features
as exposed by the Power Management Controller.
Please refer to the below specification for more details on PMC features.
http://www.intel.in/content/www/in/en/chipsets/100-series-chipset-datasheet-vol-2.html
The current version of this driver exposes SLP_S0_RESIDENCY counter.
This counter can be used for detecting fragile SLP_S0 signal related
failures and take corrective actions when PCH SLP_S0 signal is not
asserted after kernel freeze as part of suspend to idle flow
(echo freeze > /sys/power/state).
Intel Platform Controller Hub (PCH) asserts SLP_S0 signal when it
detects favorable conditions to enter its low power mode. As a
pre-requisite the SoC should be in deepest possible Package C-State
and devices should be in low power mode. For example, on Skylake SoC
the deepest Package C-State is Package C10 or PC10. Suspend to idle
flow generally leads to PC10 state but PC10 state may not be sufficient
for realizing the platform wide power potential which SLP_S0 signal
assertion can provide.
SLP_S0 signal is often connected to the Embedded Controller (EC) and the
Power Management IC (PMIC) for other platform power management related
optimizations.
In general, SLP_S0 assertion == PC10 + PCH low power mode + ModPhy Lanes
power gated + PLL Idle.
As part of this driver, a mechanism to read the SLP_S0_RESIDENCY is exposed
as an API and also debugfs features are added to indicate SLP_S0 signal
assertion residency in microseconds.
echo freeze > /sys/power/state
wake the system
cat /sys/kernel/debug/pmc_core/slp_s0_residency_usec
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Vishwanath Somayaji <vishwanath.somayaji@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Some BIOSes unconditionally send an ACPI notification to RBTN when the
system is resuming from suspend. This makes dell-rbtn send an input
event to userspace as if a function key was pressed. Prevent this by
ignoring all the notifications received while the device is suspended.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=106031
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Override default LED class suspend/resume handles, by keeping track of
the brightness level before suspending so that it can be automatically
restored on resume by calling default resume handler.
Signed-off-by: Marco Trevisan (Treviño) <mail@3v1n0.net>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
aux0_show and aux1_show consists of almost identical code. Pull that
into a common helper and make them thin wrappers. Similarly for
_store.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Asus Zenbook ux31a is providing ACPI0008 interface for ALS
(Ambient Light Sensor), which is accessible for OS => Win 7.
This sensor can be used with iio/acpi-als driver.
Since it is disabled by default, we should use asus-wmi
interface to enable it.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
My patch to the ideapad-laptop driver to get the ESC key working on the
Yoga 1170 (Yoga 3) failed to do the same for the following model, the
Lenovo Yoga 700.
Denis Gordienko managed to get it working by adding another GUID for the
new WMI interface. I have adapted his patch to normal coding style
and simplified it a bit for inclusion, but this patch is currently
untested.
Link: https://forums.lenovo.com/t5/Lenovo-Yoga-Series-Notebooks/YOGA-3-14-How-to-reclaim-my-Esc-key-and-permanently-disable/m-p/3317499
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Denis Gordienko <denis.gordienko.mail@gmail.com>
[dvhart: Whitespace cleanup, static const char *const array declaration]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Microsoft Surface Book has a tablet mode button. Print another message
once on this event instead of repeating "Unknown event...".
Unfortunately, proper support involves the _DSM method, which is not a
discoverable interface. Just print a warning for now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
* acpi-pci:
ACPI,PCI,IRQ: remove SCI penalize function
ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()
ACPI,PCI,IRQ: reduce static IRQ array size to 16
ACPI,PCI,IRQ: reduce resource requirements
* acpi-misc:
ACPI / sysfs: fix error code in get_status()
ACPI / device_sysfs: Clean up checkpatch errors
ACPI / device_sysfs: Change _SUN and _STA show functions error return to EIO
ACPI / device_sysfs: Add sysfs support for _HRV hardware revision
arm64: defconfig: Enable ACPI
ACPI / ARM64: Remove EXPERT dependency for ACPI on ARM64
ACPI / ARM64: Don't enable ACPI by default on ARM64
acer-wmi: Use acpi_dev_found()
eeepc-wmi: Use acpi_dev_found()
ACPI / utils: Rename acpi_dev_present()
* acpi-tools:
tools/power/acpi: close file only if it is open
SB700/SB710/SB800 chipset ACPI code is mostly Loongson-3 specific
routines rather than a "platform driver".
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11273/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The upcoming Elan Wolf (Dell Chromebook 11) devices need to know to look
for Elan touchpads on the i2c bus so that they will be functional.
Based on the chromeos-kernel commit :
https://chromium-review.googlesource.com/198283
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the elan trackpad to the Acer C720 (peppy) list, as it is an alternate
trackpad option. It may exist at i2c address 0x15.
Based on this change from the chromeos kernel :
https://chromium-review.googlesource.com/186253
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
compat_ioctl has to be populated for 32 bit userspace applications to work
with 64 bit kernels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Lightbar attributes are hidden if the ID of the device is not 0 (the
assumption being that 0 = cros_ec = might have a lightbar, 1 = cros_pd =
hide); however, sometimes these devices get IDs 1 and 2 (or something
else) instead of IDs 0 and 1. This prevents the lightbar attributes from
appearing when they should.
Proposed change is to instead check whether the name assigned to the
device is CROS_EC_DEV_NAME (true for cros_ec, false for cros_pd).
Signed-off-by: Clinton Sprain <clintonsprain@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Prevent memory scribble by checking that ioctl buffer size parameters
are sane.
Without this check, on 32 bits system, if .insize = 0xffffffff - 20 and
.outsize the amount to scribble, we would overflow, allocate a small
amounts and be able to write outside of the malloc'ed area.
Adding a hard limit allows argument checking of the ioctl. With the
current EC, it is expected .insize and .outsize to be at around 512 bytes
or less.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a driver for ACPI-based keyboard backlight LEDs found on
Chromebooks. The driver locates \\_SB.KBLT ACPI device and exports
backlight as "chromeos::kbd_backlight" LED class device in sysfs.
Signed-off-by: Simon Que <sque@chromium.org>
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: Evan McClain <aeroevan@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Accidentally specified a smaller record size, bring it back
to the same size as we had when we used the config file.
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
In order to handle the firmware placing the ramoops buffer
in a different location than the kernel is configured to look
probe for an ACPI device specified by GOOG9999 acpi id. If
no device is found or the first memory resource is not defined
properly fall back to the configured base and length.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Filipe Brandenburger <filbranden@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for Leon touch devices, which is the same as
slippy/falco/peppy/wolf on the same buses using the LynxPoint-LP I2C via
the i2c-designware-pci driver.
Based on the following patch:
https://chromium-review.googlesource.com/#/c/168351/
Signed-off-by: Gene Chen <gene.chen@intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Older VAIO laptops without the SN00 ACPI method will have the "handles"
variable unset. Return early from sony_nc_function_cleanup when "handles"
is null.
Signed-off-by: Lawrence Yiu <lawyiu.dev@gmail.com>
Acked-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The telemetry_core_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
toshiba_acpi:
- Fix regression caused by hotkey enabling value
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXIEZSAAoJEKbMaAwKp364mLwH/3j01EDn0JF1FIIP+kxVgeeL
g8xI+0tlFzxmdcBqW3n4q0apzVuCmHr0pbOik289l3dv7hQ5PEvdmK/VhVPYmJDL
2u/4EWmW7cvYMUAVhGB499pKac38fMUN5y97dkmoikiTQO6VaWsvdczvXuhuz/dP
OcQzRR/UttCLMe/ERxz3xh4R9kbY5Hzh4slW8Ay/sGDRrgOUFRLT8Zg3Uo7MY27i
Kq++SrH96edL1dW6XkWFIqO7NzWGlbBxTMlTlh+xmGUkOtVxUyzAID3NEDIaw6zC
7QU61eyfIJToa2SxHZ/mT9bEFNHNbJR4KoLREG6K2LbRyMhsQfMxaTym8MNzT/Q=
=+IXa
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.6-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Fix regression caused by hotkey enabling value in toshiba_acpi"
* tag 'platform-drivers-x86-v4.6-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
toshiba_acpi: Fix regression caused by hotkey enabling value
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Feng Tang <feng.tang@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Properly return rv back to the caller in the case of an error in
parse_arg. In the process remove a unused variable 'out'.
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Initializing rv to AE_OK is pointless because later function results are
assigned to them and only then the variable is used
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
It is possible that acpi_evaluate_integer might fail and value would not be
set to any value so correct this defect by returning 0 in case of an
error. This is also the correct thing to return because the backlight
subsystem will print the old value of brightness in this case.
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Commit 52cbae0127 ("toshiba_acpi: Change default Hotkey enabling value")
changed the hotkeys enabling value, as it was the same value Windows uses,
however, it turns out that the value tells the EC that the driver will now
take care of the hardware events like the physical RFKill switch or the
pointing device toggle button.
This patch reverts such commit by changing the default hotkey enabling
value to 0x09, which enables hotkey events only, making the hardware
buttons working again.
Fixes bugs 113331 and 114941.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
An S4 fix for intel-hid, new platform "quirk" for hp_accel, a fix for broader
support of ACPI resources for the Intel Punit, and a few uninitialized variable
fixes.
intel punit:
- decouple telemetry driver from the optional IPC resources
thinkpad_acpi:
- Silence an uninitialized variable warning
intel_telemetry_pltdrv:
- Silence an uninitialized variable warning
hp_accel:
- Silence an uninitialized variable warning
- Add support for HP ProBook 440 G3
intel-hid:
- add a workaround to ignore an event after waking up from S4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXGBt9AAoJEKbMaAwKp364Z9UIAJof9EYpiTf6Z8CXlHvxjhhL
O3MZRxhIel4ZePlOyZQ/IgLfkE7UIGO1k+3f6Mw0zNUadx2pN7qZ6QUlAGbC9Goz
KQp0YzfIHcY0d5jLqE/bzIv8Eb41xS9DzutZW6YEUAq/C24Y3wwJm3eqiQzv+Mxh
lYDtqnl8+seDB9dhsoAjucW2u988yAvE1oFtFzYxIyibQedBy8/rZUbTVwUPqsWO
eKl5KTzxulbF2kcohzSAAi+kLbr+4vV/YJgU2NDfGFzSQ9hp6SckU9CVei67G4Ca
08OrhprxP/5/ejPx6fx0gVPAVgCwMAB9MMKSz1oMYxWBMtM5r0DyuE9korA/PNs=
=FuS3
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.6-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"An S4 fix for intel-hid, new platform 'quirk' for hp_accel, a fix for
broader support of ACPI resources for the Intel P-unit, and a few
uninitialized variable fixes.
intel p-unit:
- decouple telemetry driver from the optional IPC resources
thinkpad_acpi:
- Silence an uninitialized variable warning
intel_telemetry_pltdrv:
- Silence an uninitialized variable warning
hp_accel:
- Silence an uninitialized variable warning
- Add support for HP ProBook 440 G3
intel-hid:
- add a workaround to ignore an event after waking up from S4"
* tag 'platform-drivers-x86-v4.6-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform:x86 decouple telemetry driver from the optional IPC resources
thinkpad_acpi: Silence an uninitialized variable warning
intel_telemetry_pltdrv: Silence an uninitialized variable warning
hp_accel: Silence an uninitialized variable warning
hp_accel: Add support for HP ProBook 440 G3
intel-hid: add a workaround to ignore an event after waking up from S4.
Currently the optional IPC resources prevent telemetry driver from
probing if these resources are not in ACPI table. This patch decouples
telemetry driver from these optional resources, so that telemetry driver
has dependency only on the necessary ACPI resources.
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
If fan_get_status() fails then "s" is not initialized. Tweak the error
handling a bit to silence this warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Presumably "pss_period" and "ioss_period" can't both be zero, but this
function is never called so we can't infer that using static analysis
alone.
Silence the warning by setting "ret" to zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
If acpi_evaluate_integer() fails then "lret" isn't initialized. I've
tweaked the error handling to avoid this issue.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Lifebook E734/E744/E754 has a LED which the manual calls "radio
components indicator". It should be lit when any radio transmitter is
enabled. Its state can be read and set using ACPI (FUNC interface,
RFKILL method).
Since the Lifebook E734/E744/E754 only has a button (as compared to a
slider) for enabling/disabling radio transmitters, I believe the LED in
question is meant to indicate whether all radio transmitters are
currently on or off. However, pressing the radio toggle button does not
automatically change the hardware state of the transmitters: it looks
like this machine relies on soft rfkill.
As for detecting whether the LED is present on a given machine, I had to
resort to educated guesswork. I assumed this LED is present on all
devices which have a radio toggle button instead of a slider. My
Lifebook E744 holds 0x01010001 in BTNI. By comparing the bits and
buttons with those of a Lifebook E8420 (BTNI=0x000F0101, has a slider),
I put my money on bit 24 as the indicator of the radio toggle button
being present. Furthermore, bit 24 is also clear on the S7020 which
does not have the toggle button or an RF LED.
Figuring out how the LED is controlled was more deterministic as all it
took was decompiling the DSDT and taking a look at method S000 (the
RFKILL method of the FUNC interface).
The LED control method implemented here is unsuitable for use with
"heavy" LED triggers, like phy0rx. Once blinking frequency achieves a
certain level, the system hangs.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
[jwoithe: Comment on bit 24 in BTNI, expanded commit msg]
Signed-off-by: Jonathan Woithe <jwoithe@just42.net>
[dvhart: Minor style and commit log adjustments]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Use shiny new acpi_dev_found() and remove all the boilerplate
to search for a particular ACPI device. No functional change.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use shiny new acpi_dev_found() and remove all the boilerplate
to search for a particular ACPI device. No functional change.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit d4edcf0d56 ("mm/gup: Switch all callers of get_user_pages() to
not pass tsk/mm") switched get_user_pages() callers to the simpler model
where they no longer pass in the thread and mm pointer. But since then
we've merged changes to a few drivers that re-introduce use of the old
interface. Let's fix them up.
They continued to work fine (thanks to the truly disgusting macros
introduced in commit cde70140fed8: "mm/gup: Overload get_user_pages()
functions"), but cause unnecessary build noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the same as the original workaround from S3 but for S4. Without
this workaround, a rfkill event will be received and it will toggle
wireless devices when radio hotkey is not pressed.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Significant refactoring of Dell laptop drivers, modularizing the smbios code.
Multiple new platforms added for ideapad, asus, dell, and alienware using
existing quirks. A few fixes and cleanups.
hp-wmi:
- Remove GPS rfkill support via pre-2009 interface
- fix unregister order in hp_wmi_rfkill_setup() once again
ideapad-laptop:
- Add ideapad Y700 (15) to the no_hw_rfkill DMI list
fujitsu-laptop:
- Support radio toggle button
intel-hid:
- allocate correct amount of memory for private struct
platform/x86:
- Make intel_scu_ipc explicitly non-modular
intel_pmc_ipc:
- Avoid pending IPC1 command during legacy suspend
- Fix GCR register base address and length
asus-nb-wmi:
- add wapf=4 quirk for ASUS X75VD
intel_telemetry_pltdrv:
- Change verbosity control bits
dell-rbtn:
- Add a comment about the XPS 13 9350
dell-wmi, dell-laptop:
- depends DMI
dell-wmi:
- support Dell Inspiron M5110
- properly process Dell Instant Launch hotkey
- enable receiving WMI events on Dell Vostro V131
- Support new hotkeys on the XPS 13 9350 (Skylake)
- Clean up hotkey table size check
- Stop storing pointers to DMI tables
dell-laptop:
- move dell_smi_error() to dell-smbios
- use dell_smbios_find_token() instead of find_token_location()
- use dell_smbios_find_token() instead of find_token_id()
- extract SMBIOS-related code to a separate module
dell-smbios:
- rename dell_smi_error() to dell_smbios_error()
- make da_tokens static
- remove find_token_{id,location}()
- implement new function for finding DMI table 0xDA tokens
- make the SMBIOS buffer static
- return the SMBIOS buffer from dell_smbios_get_buffer()
- don't return an SMBIOS buffer from dell_smbios_send_request()
- don't pass an SMBIOS buffer to dell_smbios_send_request()
- rename dell_send_request() to dell_smbios_send_request()
- rename release_buffer() to dell_smbios_release_buffer()
- rename clear_buffer() to dell_smbios_clear_buffer()
- rename get_buffer() to dell_smbios_get_buffer()
dell-led:
- use dell_smbios_send_request() for performing SMBIOS calls
- use dell_smbios_find_token() for finding mic DMI tokens
toshiba_acpi:
- Add a module parameter to disable hotkeys registration
- Add sysfs entries for the Cooling Method feature
- Add support for cooling method feature
Documentation/ABI:
- Update sysfs-driver-toshiba_acpi file
thinkpad_acpi:
- Remove ambiguous logging for "Unsupported brightness interface"
alienware-wmi:
- whitespace improvements
- Add support for two new systems: ASM200 and ASM201.
- Add support for deep sleep control.
- Add initial support for alienware graphics amplifier.
- Add support for new platform: X51-R3
- Clean up whitespace for ASM100 platform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW8s77AAoJEKbMaAwKp364iVgH/18Tpefbc7uOrNak4zfTmvVO
CQjLdbnbCYoeNjwgdYSZNlaR+E2TuMdqmBXXLEr3kqicpmX15l+V5y8xJkDmGpxw
0RmwJnkdIpmkZcjb3/2abOtIuOj1Y/tXCp5mY1FoaDYBQVzO+ZsPEGNQcMu5uJpa
qZTw9UwiSPUspTrHHbS7/Bzv7yFnxlWC1nmt6G5zL4OMEv2AGbuVSstXVGySIML5
TfFdisUBIXQplzwpDytHGqtGUJMc0NnT1s66beuo1oBdEFTFtBNpFySW3goV2nrZ
JPbvyaV3tD24NYNmU9WH653InX4KuaGiJRWVT31a/I5HVVlx7mZdUYRI+EYAnmE=
=e0E4
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.6-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Significant refactoring of Dell laptop drivers, modularizing the
smbios code. Multiple new platforms added for ideapad, asus, dell,
and alienware using existing quirks. A few fixes and cleanups.
hp-wmi:
- Remove GPS rfkill support via pre-2009 interface
- fix unregister order in hp_wmi_rfkill_setup() once again
ideapad-laptop:
- Add ideapad Y700 (15) to the no_hw_rfkill DMI list
fujitsu-laptop:
- Support radio toggle button
intel-hid:
- allocate correct amount of memory for private struct
platform/x86:
- Make intel_scu_ipc explicitly non-modular
intel_pmc_ipc:
- Avoid pending IPC1 command during legacy suspend
- Fix GCR register base address and length
asus-nb-wmi:
- add wapf=4 quirk for ASUS X75VD
intel_telemetry_pltdrv:
- Change verbosity control bits
dell-rbtn:
- Add a comment about the XPS 13 9350
dell-wmi, dell-laptop:
- depends DMI
dell-wmi:
- support Dell Inspiron M5110
- properly process Dell Instant Launch hotkey
- enable receiving WMI events on Dell Vostro V131
- Support new hotkeys on the XPS 13 9350 (Skylake)
- Clean up hotkey table size check
- Stop storing pointers to DMI tables
dell-laptop:
- move dell_smi_error() to dell-smbios
- use dell_smbios_find_token() instead of find_token_location()
- use dell_smbios_find_token() instead of find_token_id()
- extract SMBIOS-related code to a separate module
dell-smbios:
- rename dell_smi_error() to dell_smbios_error()
- make da_tokens static
- remove find_token_{id,location}()
- implement new function for finding DMI table 0xDA tokens
- make the SMBIOS buffer static
- return the SMBIOS buffer from dell_smbios_get_buffer()
- don't return an SMBIOS buffer from dell_smbios_send_request()
- don't pass an SMBIOS buffer to dell_smbios_send_request()
- rename dell_send_request() to dell_smbios_send_request()
- rename release_buffer() to dell_smbios_release_buffer()
- rename clear_buffer() to dell_smbios_clear_buffer()
- rename get_buffer() to dell_smbios_get_buffer()
dell-led:
- use dell_smbios_send_request() for performing SMBIOS calls
- use dell_smbios_find_token() for finding mic DMI tokens
toshiba_acpi:
- Add a module parameter to disable hotkeys registration
- Add sysfs entries for the Cooling Method feature
- Add support for cooling method feature
Documentation/ABI:
- Update sysfs-driver-toshiba_acpi file
thinkpad_acpi:
- Remove ambiguous logging for "Unsupported brightness interface"
alienware-wmi:
- whitespace improvements
- Add support for two new systems: ASM200 and ASM201.
- Add support for deep sleep control.
- Add initial support for alienware graphics amplifier.
- Add support for new platform: X51-R3
- Clean up whitespace for ASM100 platform"
* tag 'platform-drivers-x86-v4.6-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (47 commits)
hp-wmi: Remove GPS rfkill support via pre-2009 interface
hp-wmi: fix unregister order in hp_wmi_rfkill_setup() once again
dell-wmi: support Dell Inspiron M5110
dell-wmi: properly process Dell Instant Launch hotkey
dell-wmi: enable receiving WMI events on Dell Vostro V131
dell-smbios: rename dell_smi_error() to dell_smbios_error()
dell-laptop: move dell_smi_error() to dell-smbios
ideapad-laptop: Add ideapad Y700 (15) to the no_hw_rfkill DMI list
fujitsu-laptop: Support radio toggle button
intel-hid: allocate correct amount of memory for private struct
platform/x86: Make intel_scu_ipc explicitly non-modular
intel_pmc_ipc: Avoid pending IPC1 command during legacy suspend
intel_pmc_ipc: Fix GCR register base address and length
asus-nb-wmi: add wapf=4 quirk for ASUS X75VD
intel_telemetry_pltdrv: Change verbosity control bits
dell-rbtn: Add a comment about the XPS 13 9350
dell-wmi: Support new hotkeys on the XPS 13 9350 (Skylake)
dell-wmi: Clean up hotkey table size check
dell-wmi, dell-laptop: depends DMI
dell-wmi: Stop storing pointers to DMI tables
...
GPS rfkill support via pre-2009 WMI interface uses hp_wmi_get_sw_state()
and hp_wmi_get_hw_state() to query its current hard and soft block state,
respectively.
In hp_wmi_get_sw_state() a mask is calculated which bit should be checked
in an int value returned by firmware to get current block state: 0x200 <<
(r * 8) which with r being 3 for GPS results in overflow and mask of zero.
The same goes for hp_wmi_get_hw_state().
This effectively means that GPS rfkill on this WMI interface is considered
always both hard and soft blocked.
Unfortunately, later when rfkill subsystem calls hp_wmi_set_block() to sync
this block to hardware firmware at least on my old nc6400 gets confused and
sets both hard and soft blocks on WiFi and BT.
This happens for example on hp-wmi module load.
Since due to overflow described above it is dubious that this ever worked
correctly and HP laptops with modems having GPS support seem to all have
been released well past year 2009 let's just remove GPS rfkill support via
pre-2009 WMI interface.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
rfkill registration order in hp_wmi_rfkill_setup() is:
1) WiFi,
2) BT,
3) WWAN,
5) GPS.
Unregistration when cleaning up on error return should happen in reverse
order.
This means that: If BT rfkill fails to be allocated we possibly need to
first unregister WiFi rfkill before destroying it.
The same goes with (WWAN, BT) and (GPS, WWAN) pairs.
Also, if WWAN rfkill fails to register we need to (possibly) unregister BT
not the GPS one. And if GPS rfkill fails to register we need to unregister
WWAN not the BT one.
We never need to unregister GPS rfkill here since if GPS rfkill
registration succeeds this function returns without error so no cleanup is
necessary.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Similarly to Dell Vostro V131, Dell Inspiron M5110 also requires an
SMBIOS request to be issued in order for WMI events to be generated and
does not raise an i8042 interrupt when the Dell Instant Launch hotkey is
pressed. However, the event code for that hotkey on this machine is
0xe029, so add it to the legacy keymap.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Darek Stojaczyk <darek.stojaczyk@gmail.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
On models on which an SMBIOS request needs to be issued in order for WMI
events to be generated, pressing the Dell Instant Launch hotkey does not
raise an i8042 interrupt - only a WMI event is generated (0xe025 on Dell
Vostro V131). As that WMI event is the only way the kernel will be
notified about pressing the Dell Instant Launch hotkey on such machines,
the relevant keymap entry has to be changed to a KE_KEY one. However,
the same WMI event should still be ignored on machines which do not
require an SMBIOS request for enabling WMI, so filter it conditionally
in dell_wmi_process_key().
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
On some laptop models (e.g. Dell Vostro V131), WMI events are not
generated until a specific SMBIOS request is issued to register an event
listener [1]. As there seems to be no ACPI method or SMBIOS request to
determine without possible side effects whether a given machine needs to
issue this SMBIOS request in order to receive WMI events, DMI matching
is used to whitelist the models which need it.
[1] https://lists.us.dell.com/pipermail/libsmbios-devel/2015-July/000612.html
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
As dell_smi_error() is exported by dell-smbios, its prefix should be
consistent with other exported symbols, so change function name to
dell_smbios_error().
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The dell_smi_error() method could be used by modules other than
dell-laptop for convenient translation of SMBIOS request errors into
errno values. Thus, move it to dell-smbios.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Some Lenovo ideapad models lack a physical rfkill switch.
On Lenovo models ideapad Y700 Touch-15ISK and ideapad Y700-15ISK,
ideapad-laptop would wrongly report all radios as blocked by
hardware which caused wireless network connections to fail.
Add these models without an rfkill switch to the no_hw_rfkill list.
Signed-off-by: John Dahlstrom <jodarom@sdf.org>
Cc: <stable@vger.kernel.org> # 3.17.x-: 4fa9dab: ideapad_laptop: Lenovo G50-30 fix rfkill reports wireless blocked
Cc: <stable@vger.kernel.org>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Lifebook E734/E744/E754 has a radio toggle button which uses code 0x420.
Map it to KEY_RFKILL.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
We want the size of the struct, not of a pointer to it. To be future
proof, just dereference the pointer to get the desired type.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The Kconfig currently controlling compilation of this code is:
drivers/platform/x86/Kconfig:config INTEL_SCU_IPC
drivers/platform/x86/Kconfig: bool "Intel SCU IPC Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_pci_driver() uses the same init level priority as
builtin_pci_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We don't replace module.h with init.h since the file already has that.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
During legacy suspend flow, IPC1 commands are being requested
from opregion driver. But the PMC_IPC1 command will timeout as example:
[ 281.444600] ipc_debug##: ipc_send_command: cmd=0x201ff,
[ 281.444648] wbuf[0]=0x4ea6
[ 281.444668] wbuf[1]=0x0
[ 281.444674] wbuf[2]=0x0
[ 281.444676] wbuf[3]=0x0
[ 284.446467] pmc-ipc-plat INT34D2:00: IPC timed out, TS=0x4, CMD=0x200ff
This is because before the opregion driver could send IPC1 commands,
the PMC_IPC irq is already suspended. Which makes the IPC command to
timeout.
Solution: register pmc_ipc irq as IRQF_NO_SUSPEND
Signed-off-by: Ananth Krishna R <ananth.krishna.r@intel.com>
Signed-off-by: Bharath K Veera <bharath.k.veera@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
GCR register (pmc_cfg register) is at offset 0x1008, and
remapping of 0x4 bytes is enough.
Signed-off-by: Francois-Nicolas Muller <francois-nicolas.muller@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Wi-Fi on ASUS X75VD laptop does not work unless asus_nb_wmi module
is loaded with wapf=4 option. Add quirk for this.
Signed-off-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Due to a recent fix in the firmware, the Punit verbosity control bits
now adhere to the correct pattern. Hence remove the workaround and
do a read-modify-write of the register.
Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
On the XPS 13 9350, the dell-rbtn mechanism has a new device id, and
the DSDT turns it off if a new enough _OSI is supported. Add a
comment about why we don't bother supporting it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The XPS 13 9350 sends WMI keypress events that aren't enumerated in
the DMI table. Add a table listing them. To avoid breaking things
that worked before, these un-enumerated hotkeys won't be used if the
DMI table maps them to something else.
FWIW, it appears that the DMI table may be a legacy thing and we
might want to rethink how we handle events in general. As an
example, a whole lot of things map to KEY_PROG3 via the DMI table.
This doesn't send keypress events for any of the new events. They
appear to all be handled by other means (keyboard illumination is
handled automatically and rfkill is handled by intel-hid).
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Checking the table for a minimum size of 7 bytes makes no sense: any valid
hotkey table has a size that's a multiple of 4.
Clean this up: replace the hardcoded header length with a sizeof and
change the check to ignore an empty hotkey table. The only behavior
change is that a 7-byte table (which is nonsensical) will now be
treated as absent instead of as valid but empty.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
dell-wmi and dell-laptop will compile but won't work right if DMI
isn't selected.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
[arnd: Use depends instead of selects to avoid recursive dependencies]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The dmi_walk function maps the DMI table, walks it, and unmaps it.
This means that the dell_bios_hotkey_table that find_hk_type stores
points to unmapped memory by the time it gets read.
I've been able to trigger crashes caused by the stale pointer a
couple of times, but never on a stock kernel.
Fix it by generating the keymap in the dmi_walk callback instead of
storing a pointer.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
As dell-laptop has been changed to use dell_smbios_find_token() instead
of directly accessing members of the da_tokens table, the latter can be
marked static.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
As dell-laptop has been changed to use dell_smbios_find_token() instead
of find_token_id() and find_token_location(), these functions can be
safely removed.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Replace all uses of find_token_location() with dell_smbios_find_token()
to avoid directly accessing the da_tokens table.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Replace all uses of find_token_id() with dell_smbios_find_token() to
avoid directly accessing the da_tokens table.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Ultimately, the da_tokens table should not be exported from dell-smbios.
Currently, in some cases, dell-laptop accesses that table's members
directly, so implement a new function, dell_smbios_find_token(), which
returns a pointer to an entry inside the da_tokens table with the given
token ID (or NULL if it is not found).
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
As dell-laptop has been changed to always retrieve a pointer to the
SMBIOS buffer using dell_smbios_get_buffer(), the SMBIOS buffer can be
marked static.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Ultimately, the SMBIOS buffer should not be exported from dell-smbios.
Currently, dell-laptop accesses it directly using a global variable, so
make dell_smbios_get_buffer() return a pointer to the SMBIOS buffer and
replace all uses of the global variable with local variables.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
An SMBIOS buffer pointer does not need to be returned by
dell_smbios_send_request(), because SMBIOS call results are stored in
the buffer exported by the module.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Passing an SMBIOS buffer pointer to dell_smbios_send_request() is
redundant as it should always operate on the SMBIOS buffer exported from
the module.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
As dell_send_request() is exported from the module, its prefix should be
consistent with other exported symbols, so change function name to
dell_smbios_send_request().
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
As release_buffer() is exported from the module, it has to be renamed to
something less generic, so add a "dell_smbios_" prefix to the function
name.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
As clear_buffer() is exported from the module, it has to be renamed to
something less generic, so add a "dell_smbios_" prefix to the function
name.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
As get_buffer() is exported from the module, it has to be renamed to
something less generic, so add a "dell_smbios_" prefix to the function
name.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Extract SMBIOS-related code from dell-laptop to a new kernel module,
dell-smbios. The static specifier is removed from exported symbols,
otherwise code is just moved around.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
[dvhart: Include linux/io.h in dell-smbios.c as caught by lkp]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Some laptop models have working hotkeys without the need of the driver
to activate them.
This patch adds a module parameter to tell the driver not to register
the hotkeys.
The new parameter is useful in DE less installations or where the DE
does not handle the hotkeys (see bug 99501).
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch adds support to query and set the "Cooling Method" feature,
which basically changes how the system fan behaves, depending on the
supported cooling methods.
Depending on the laptop model, these are the (so far...) available
cooling methods:
- Maximum Performance
- Performance
- Battery Optimized
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
"Unsupported brightness interface" message gets logged on
machines that are well supported.
Signed-off-by: Eric Curtin <ericcurtin17@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.6 kernel.
Overall the coolest thing here for me is the nouveau maxwell signed
firmware support from NVidia, it's taken a long while to extract this
from them.
I also wish the ARM vendors just designed one set of display IP, ARM
display block proliferation is definitely increasing.
Core:
- drm_event cleanups
- Internal API cleanup making mode_fixup optional.
- Apple GMUX vga switcheroo support.
- DP AUX testing interface
Panel:
- Refactoring of DSI core for use over more transports.
New driver:
- ARM hdlcd driver
i915:
- FBC/PSR (framebuffer compression, panel self refresh) enabled by default.
- Ongoing atomic display support work
- Ongoing runtime PM work
- Pixel clock limit checks
- VBT DSI description support
- GEM fixes
- GuC firmware scheduler enhancements
amdkfd:
- Deferred probing fixes to avoid make file or link ordering.
amdgpu/radeon:
- ACP support for i2s audio support.
- Command Submission/GPU scheduler/GPUVM optimisations
- Initial GPU reset support for amdgpu
vmwgfx:
- Support for DX10 gen mipmaps
- Pageflipping and other fixes.
exynos:
- Exynos5420 SoC support for FIMD
- Exynos5422 SoC support for MIPI-DSI
nouveau:
- GM20x secure boot support - adds acceleration for Maxwell GPUs.
- GM200 support
- GM20B clock driver support
- Power sensors work
etnaviv:
- Correctness fixes for GPU cache flushing
- Better support for i.MX6 systems.
imx-drm:
- VBlank IRQ support
- Fence support
- OF endpoint support
msm:
- HDMI support for 8996 (snapdragon 820)
- Adreno 430 support
- Timestamp queries support
virtio-gpu:
- Fixes for Android support.
rockchip:
- Add support for Innosilicion HDMI
rcar-du:
- Support for 4 crtcs
- R8A7795 support
- RCar Gen 3 support
omapdrm:
- HDMI interlace output support
- dma-buf import support
- Refactoring to remove a lot of legacy code.
tilcdc:
- Rewrite of pageflipping code
- dma-buf support
- pinctrl support
vc4:
- HDMI modesetting bug fixes
- Significant 3D performance improvement.
fsl-dcu (FreeScale):
- Lots of fixes
tegra:
- Two small fixes
sti:
- Atomic support for planes
- Improved HDMI support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1063 commits)
drm/amdgpu: release_pages requires linux/pagemap.h
drm/sti: restore mode_fixup callback
drm/amdgpu/gfx7: add MTYPE definition
drm/amdgpu: removing BO_VAs shouldn't be interruptible
drm/amd/powerplay: show uvd/vce power gate enablement for tonga.
drm/amd/powerplay: show uvd/vce power gate info for fiji
drm/amdgpu: use sched fence if possible
drm/amdgpu: move ib.fence to job.fence
drm/amdgpu: give a fence param to ib_free
drm/amdgpu: include the right version of gmc header files for iceland
drm/radeon: fix indentation.
drm/amd/powerplay: add uvd/vce dpm enabling flag to fix the performance issue for CZ
drm/amdgpu: switch back to 32bit hw fences v2
drm/amdgpu: remove amdgpu_fence_is_signaled
drm/amdgpu: drop the extra fence range check v2
drm/amdgpu: signal fences directly in amdgpu_fence_process
drm/amdgpu: cleanup amdgpu_fence_wait_empty v2
drm/amdgpu: keep all fences in an RCU protected array v2
drm/amdgpu: add number of hardware submissions to amdgpu_fence_driver_init_ring
drm/amdgpu: RCU protected amd_sched_fence_release
...
Here is the big staging driver pull request for 4.6-rc1.
Lots of little things here, over 1600 patches or so. Notible is all of
the good Lustre work happening, those developers have finally woken up
and are cleaning up their code greatly. The Outreachy intern
application process is also happening, which brought in another 400 or
so patches. Full details are in the very long shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbrc3EACgkQMUfUDdst+ylu5ACgpdTKjrZn2vHElW3GRhTpzJdQ
wz8AoJDeur2DmBkQrKD5/u/WL4UTRNZJ
=+Q6N
-----END PGP SIGNATURE-----
Merge tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big staging driver pull request for 4.6-rc1.
Lots of little things here, over 1600 patches or so. Notable is all
of the good Lustre work happening, those developers have finally woken
up and are cleaning up their code greatly. The Outreachy intern
application process is also happening, which brought in another 400 or
so patches. Full details are in the very long shortlog.
All of these have been in linux-next with no reported issues"
* tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1673 commits)
staging: lustre: fix aligments in lnet selftest
staging: lustre: report minimum of two buffers for LNet selftest load test
staging: lustre: test for proper errno code in lstcon_rpc_trans_abort
staging: lustre: filter remaining extra spacing for lnet selftest
staging: lustre: remove extra spacing when setting variable for lnet selftest
staging: lustre: remove extra spacing of variable declartions for lnet selftest
staging: lustre: fix spacing issues checkpatch reported in lnet selftest
staging: lustre: remove returns in void function for lnet selftest
staging: lustre: fix bogus lst errors for lnet selftest
staging: netlogic: Replacing pr_err with dev_err after the call to devm_kzalloc
staging: mt29f_spinand: Replacing pr_info with dev_info after the call to devm_kzalloc
staging: android: ion: fix up file mode
staging: ion: debugfs invalid gfp mask
staging: rts5208: Replace pci_enable_device with pcim_enable_device
Staging: ieee80211: Place constant on right side of the test.
staging: speakup: Replace del_timer with del_timer_sync
staging: lowmemorykiller: fix 2 checks that checkpatch complained
staging: mt29f_spinand: Drop void pointer cast
staging: rdma: hfi1: file_ops: Replace ALIGN with PAGE_ALIGN
staging: rdma: hfi1: driver: Replace IS_ALIGNED with PAGE_ALIGNED
...
Add missing HAS_IOMEM dependency to fix the allyesconfig build error on
ARCH=um (for x86_64):
drivers/platform/goldfish/pdev_bus.c: In function ‘goldfish_pdev_bus_probe’:
drivers/platform/goldfish/pdev_bus.c:191:18: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
pdev_bus_base = ioremap(pdev_bus_addr, pdev_bus_len);
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge issues and confusions people were having with
the goldfish drivers due to changes for them showing up in two different
trees.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coherent mapping guarantees that the device and CPU are in sync.
Signed-off-by: Shraddha Barke <shraddha.6596@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Centralize gmux' ACPI HID in a header file and add apple_gmux_present().
This can be used by other drivers to activate quirks specific to dual
GPU MacBook Pros & Mac Pros. The alternative would be to hardcode DMI
or PCI IDs and amend them whenever Apple introduces a new machine.
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/89c23769058a340e5e11d4a7102f3793d3b0c94c.1452525860.git.lukas@wunner.de
gmux has 3 switch registers:
* GMUX_PORT_SWITCH_DISPLAY switches the panel
* GMUX_PORT_SWITCH_DDC switches the panel's DDC lines
(only on pre-retinas; on retinas this is a no-op)
* GMUX_PORT_SWITCH_EXTERNAL switches the external DP port(s)
(only on models without Thunderbolt, i.e. introduced before 2011;
those with Thunderbolt switch only HPD/AUX, not the main link)
Currently we switch all 3 registers in unison.
gmux does not preserve the switch state during suspend, so we currently
read GMUX_PORT_SWITCH_DISPLAY before suspend and restore all 3 registers
to this value on resume.
With the upcoming ->switch_ddc callback, GMUX_PORT_SWITCH_DDC may
temporarily contain a different value than the other 2 registers.
If we happen to suspend at this moment, we'll write an incorrect
value to GMUX_PORT_SWITCH_DDC on resume.
Also, on models with Thunderbolt the integrated GPU is unable to drive
the external DP port(s), so we want to keep GMUX_PORT_SWITCH_EXTERNAL
permanently switched to the discrete GPU on those machines.
Consequently we can no longer assume that GMUX_PORT_SWITCH_DISPLAY
represents the correct value for all 3 registers on suspend.
Track the state of all 3 registers: Add gmux_read_switch_state() and
gmux_write_switch_state(). Instead of reading the switch state on
every suspend, read it once on driver initialization so that we know
the current switch state all the time. (This allows us to use some
optimizations and shortcuts, e.g. we can skip switching DDC if we
know that it's already switched to the requested GPU.) Change the
->switchto callback to use gmux_write_switch_state().
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/5679f414cb0ddf1654dcc359571f3764b275edf0.1452525860.git.lukas@wunner.de
Allow handlers to declare their capabilities and allow clients to
obtain that information. So far we have these use cases:
* If the handler is able to switch DDC separately, clients need to
probe EDID with drm_get_edid_switcheroo(). We should allow them
to detect a capable handler to ensure this function only gets
called when needed.
* Likewise if the handler is unable to switch AUX separately, the active
client needs to communicate link training parameters to the inactive
client, which may then skip the AUX handshake and set up its output
with these pre-calibrated values (DisplayPort specification v1.1a,
section 2.5.3.3). Clients need a way to recognize such a situation.
The flags for the radeon_atpx_handler and amdgpu_atpx_handler are
initially set to 0, this can later on be amended with
handler_flags |= VGA_SWITCHEROO_CAN_SWITCH_DDC;
when a ->switch_ddc callback is added.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61115
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/2b0d93ed6e511ca09e95e45e0b35627f330fabce.1452525860.git.lukas@wunner.de
We recently messed up the error handling here. We can return with the
pipe->lock held or sometimes we unlock twice by mistake.
Fixes: 2f3be88237 ('goldfish_pipe: Pin pages to memory while copying and other cleanups')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These were some items that were pointed out in previous patches that
weren't caught be previous reviewers, but should be applied to other
parts of the driver as well.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
[dvhart: reverted a couple incorrect line wrapping changes]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Both of these systems support:
* 2 lighting control zones
* HDMI mux control
* deep sleep control (to enable wakup from controller)
The ASM201 also supports the external graphics amplifier.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Allow for user configuration of BIOS settings that allow the system to be
turned on via HID devices.
The feature requires hardware architectural modifications and can not be
supported on existing systems.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
[dvhart: comment formatting and line length fixes]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The alienware graphics amplifier is a device that provides external access
to a full PCIe slot, USB hub, and additional control zone.
This patch enables support for reading status whether the cable is plugged
in as well as for setting the colors in the new zone on the amplifier.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
[dvhart: minor comment formatting fixes]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The X51-R3 is in the X51 family. It includes 3 internal
lighting zones as well as is the first AW desktop that
includes support for a graphics amplifier.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This brings them more in line with the usage of whitespace
in other platforms.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
"count" is controlled by the user and it can be negative. Let's prevent
that by making it unsigned. You have to have CAP_SYS_RAWIO to call this
function so the bug is not as serious as it could be.
Fixes: 5369c02d95 ('intel_scu_ipc: Utility driver for intel scu ipc')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
intel_hid_keymap contains a duplicate entry for KEY_HOME and an
incorrect HID index for KEY_PAGEDOWN
Reported-by: Pavel Bludov <pbludov@gmail.com>
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Add ACPI binding to the android pipe driver
Signed-off-by: Jason Hu <jia-cheng.hu@intel.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For reading and writing guest user space buffers, currently the kernel
sends the guest virtual address of the buffer to the pipe device. This
virtual address has to be first converted to a guest physical address.
Doing this translation on the QEMU side is inefficient and requires
additional handling when KVM is enabled, whose implementation would
either incur intrusive changes to QEMU's KVM support code or suffer
from poor performance, see commit 08c7228c50f8 ("x86-kvm: only sync
SREGS when doing address translation") of $AOSP/external/qemu for
details, and thus should be avoided if possible.
There is a TODO comment in hw/misc/android_pipe.c in the new Android
emulator source tree ($AOSP/external/qemu-android) which requests that
the translation be done on the kernel side and that physical addresses
be passed to the device instead of virtual ones. Once the QEMU-side
implementation is done, the kernel will need to support both the new
paddr-based pipe device and the old vaddr-based one (which will
continue to be used by the classic emulator). This patch achieves that
by leveraging the device version register available in the new device.
See https://android-review.googlesource.com/128280 for the QEMU-side
patch.
In addition, use the mmap semaphore (in read mode) to safeguard the
call to get_user_pages().
Signed-off-by: Yu Ning <yu.ning@intel.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On PIPE_ERROR_AGAIN, just stopping in the middle of a transfer and
returning the number of bytes actually handled is the right behavior.
Other errors should be returned on the next read() or write() call.
Continue logging those until we confirm nothing actually relies on the
existing (wrong) behavior of dropping errors on the floor.
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add bindings so we don't need to rely on goldfish virtual bus for
probing any more, which means we don't need ARM and MIPS goldfish
board code for instantiating the bus.
In the long term we would like to move towards replacing the Android
pipe with virtio-vsock that is currently under development.
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing code had a troubling TODO statement concerning the fact
that it just did a check if the page that the QEMU backend was going to
read from / write to was there before the call to the QEMU backend and
then relying on the fact that the page stayed around, even in a
preemptible SMP kernel. Obviously the page could go away or be
reassigned, and strange things may happen.
Further, writes were not tracked, so any use of COW or KSM-like
features would break completely. Probably that was never used by adbd
(the only current active user of the pipe), but could prove much more
dangerous for the GPU passthrough mechanism.
Instead, use get_user_pages() as the comment suggested and cleanup the
error path and add the set_page_dirt() call on a successful read
operation.
Also clarify the count used to return from successful read/write calls
and use Linux style commentary in various places of the file.
Note: The "just ignore error and return whatever we read so far" error
handling is really quite horrific. I cannot change it without a more
careful study of all user space ABIs reliance on this 'feature'.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It just makes it harder to figure out which commands are being used.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On new virtual devices, the goldfish virtual bus can be replaced with
autoprobing infrastructure like Device Tree. Refactor the goldfish
kernel configs to better accommodate this.
Move the goldfish platform into a menuconfig in the style of the chrome
platform, and separate the goldfish bus into its own config option.
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Jin Qian <jinqian@android.com>
[Corrected a tristate to bool]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the Yoga 900 models the Lenovo Yoga 700 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.
This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing
the wifi breakage.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1295272
Tested-by: <dinyar.rabady+spam@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch fixes compile time warnings when CONFIG_PM_SLEEP
is undefined. In this case sleep related counters are unused.
Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on
top of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates
of the ACPICA's copyright notices, a code fixup resulting from
a regression fix that was necessary in the upstream code only
(the regression fixed by it has never been present in Linux)
and a compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke
it on practically all architectures other than x86 and make a
couple of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether
or not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on
the problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up
a bit and update the MAINTAINERS information related to it
(Chanwoo Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=bKJ9
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"This includes fixes on top of the previous batch of PM+ACPI updates
and some new material as well.
From the new material perspective the most significant are the driver
core changes that should allow USB devices to stay suspended over
system suspend/resume cycles if they have been runtime-suspended
already beforehand. Apart from that, ACPICA is updated to upstream
revision 20160108 (cosmetic mostly, but including one fixup on top of
the previous ACPICA update) and there are some devfreq updates the
didn't make it before (due to timing).
A few recent regressions are fixed, most importantly in the cpuidle
menu governor and in the ACPI backlight driver and some x86 platform
drivers depending on it.
Some more bugs are fixed and cleanups are made on top of that.
Specifics:
- Modify the driver core and the USB subsystem to allow USB devices
to stay suspended over system suspend/resume cycles if they have
been runtime-suspended already beforehand and fix some bugs on top
of these changes (Tomeu Vizoso, Rafael Wysocki).
- Update ACPICA to upstream revision 20160108, including updates of
the ACPICA's copyright notices, a code fixup resulting from a
regression fix that was necessary in the upstream code only (the
regression fixed by it has never been present in Linux) and a
compiler warning fix (Bob Moore, Lv Zheng).
- Fix a recent regression in the cpuidle menu governor that broke it
on practically all architectures other than x86 and make a couple
of optimizations on top of that fix (Rafael Wysocki).
- Clean up the selection of cpuidle governors depending on whether or
not the kernel is configured for tickless systems (Jean Delvare).
- Revert a recent commit that introduced a regression in the ACPI
backlight driver, address the problem it attempted to fix in a
different way and revert one more cosmetic change depending on the
problematic commit (Hans de Goede).
- Add two more ACPI backlight quirks (Hans de Goede).
- Fix a few minor problems in the core devfreq code, clean it up a
bit and update the MAINTAINERS information related to it (Chanwoo
Choi, MyungJoo Ham).
- Improve an error message in the ACPI fan driver (Andy Lutomirski).
- Fix a recent build regression in the cpupower tool (Shreyas
Prabhu)"
* tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
cpuidle: menu: Avoid pointless checks in menu_select()
sched / idle: Drop default_idle_call() fallback from call_cpuidle()
cpupower: Fix build error in cpufreq-info
cpuidle: Don't enable all governors by default
cpuidle: Default to ladder governor on ticking systems
time: nohz: Expose tick_nohz_enabled
ACPICA: Update version to 20160108
ACPICA: Silence a -Wbad-function-cast warning when acpi_uintptr_t is 'uintptr_t'
ACPICA: Additional 2016 copyright changes
ACPICA: Reduce regression fix divergence from upstream ACPICA
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Satellite R830
ACPI / video: Revert "thinkpad_acpi: Use acpi_video_handles_brightness_key_presses()"
ACPI / video: Document acpi_video_handles_brightness_key_presses() a bit
ACPI / video: Fix using an uninitialized mutex / list_head in acpi_video_handles_brightness_key_presses()
ACPI / video: Revert "ACPI / video: driver must be registered before checking for keypresses"
ACPI / fan: Improve acpi_device_update_power error message
ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Portege R700
cpuidle: menu: Fix menu_select() for CPUIDLE_DRIVER_STATE_START == 0
MAINTAINERS: Add devfreq-event entry
MAINTAINERS: Add missing git repository and directory for devfreq
...
Add intel punit and telemetry driver for APL SoCs.
Add intel-hid driver for various laptop hotkey support.
Add asus-wireless radio control driver.
Keyboard backlight support/improvements for ThinkPads, Vaio, and Toshiba.
Several hotkey related fixes and improvements for dell and toshiba.
Fix oops on dual GPU Macs in apple-gmux.
A few new device IDs and quirks.
Various minor config related build issues and cleanups.
surface pro 4:
- fix compare_const_fl.cocci warnings
- Add support for Surface Pro 4 Buttons
platform/x86:
- Add Intel Telemetry Debugfs interfaces
- Add Intel telemetry platform device
- Add Intel telemetry platform driver
- Add Intel Telemetry Core Driver
- add NULL check for input parameters
- add Intel P-Unit mailbox IPC driver
- update acpi resource structure for Punit
thinkpad_acpi:
- Add support for keyboard backlight
dell-wmi:
- Process only one event on devices with interface version 0
- Check if Dell WMI descriptor structure is valid
- Improve unknown hotkey handling
- Use a C99-style array for bios_to_linux_keycode
tc1100-wmi:
- fix build warning when CONFIG_PM not enabled
asus-wireless:
- Add ACPI HID ATK4001
- Add Asus Wireless Radio Control driver
asus-wmi:
- drop to_platform_driver macro
intel-hid:
- new hid event driver for hotkeys
sony-laptop:
- Keyboard backlight control for some Vaio Fit models
ideapad-laptop:
- Add Lenovo ideapad Y700-17ISK to no_hw_rfkill dmi list
apple-gmux:
- Assign apple_gmux_data before registering
toshiba_acpi:
- Add rfkill dependency to ACPI_TOSHIBA entry
- Fix keyboard backlight sysfs entries not being updated
- Add WWAN RFKill support
- Add support for WWAN devices
- Fix blank screen at boot if transflective backlight is supported
- Propagate the hotkey value via genetlink
toshiba_bluetooth:
- Add missing newline in toshiba_bluetooth_present function
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWnuSYAAoJEKbMaAwKp364xckH/A/INtwr1LzmSw8fsEIe6IGQ
MKEzCHZOUdSPcZSHcTW/fE/J8kt1j4YdR2kkxNbivtxST5O81E6KfAmo37TRrTNx
bunVt7Swj7FcPsm6t0m3PQkbWkOy3UMUncRaZjeofzhRl2m+bHEycEIJsHs7OU+e
7UPjbWZjRz6/LahcryKDH/lRhweMEsgZSFzjNlby8Wzz4LRCu8HLwNGUQa0vQfNI
2UW+s7g2ZkFXx9fbmWu9twkyP7LwNoaZ3IDGsEffIYjmXeZKe+yTPy/TueYYzpon
aclJSjhxLNnfWUaO0eUt/H4T5VyUag3v3mp6PVSwm2TA3Cpuh1SDYrJcurls6Mw=
=b4Wa
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.5-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Add intel punit and telemetry driver for APL SoCs.
Add intel-hid driver for various laptop hotkey support.
Add asus-wireless radio control driver.
Keyboard backlight support/improvements for ThinkPads, Vaio, and Toshiba.
Several hotkey related fixes and improvements for dell and toshiba.
Fix oops on dual GPU Macs in apple-gmux.
A few new device IDs and quirks.
Various minor config related build issues and cleanups.
surface pro 4:
- fix compare_const_fl.cocci warnings
- Add support for Surface Pro 4 Buttons
platform/x86:
- Add Intel Telemetry Debugfs interfaces
- Add Intel telemetry platform device
- Add Intel telemetry platform driver
- Add Intel Telemetry Core Driver
- add NULL check for input parameters
- add Intel P-Unit mailbox IPC driver
- update acpi resource structure for Punit
thinkpad_acpi:
- Add support for keyboard backlight
dell-wmi:
- Process only one event on devices with interface version 0
- Check if Dell WMI descriptor structure is valid
- Improve unknown hotkey handling
- Use a C99-style array for bios_to_linux_keycode
tc1100-wmi:
- fix build warning when CONFIG_PM not enabled
asus-wireless:
- Add ACPI HID ATK4001
- Add Asus Wireless Radio Control driver
asus-wmi:
- drop to_platform_driver macro
intel-hid:
- new hid event driver for hotkeys
sony-laptop:
- Keyboard backlight control for some Vaio Fit models
ideapad-laptop:
- Add Lenovo ideapad Y700-17ISK to no_hw_rfkill dmi list
apple-gmux:
- Assign apple_gmux_data before registering
toshiba_acpi:
- Add rfkill dependency to ACPI_TOSHIBA entry
- Fix keyboard backlight sysfs entries not being updated
- Add WWAN RFKill support
- Add support for WWAN devices
- Fix blank screen at boot if transflective backlight is supported
- Propagate the hotkey value via genetlink
toshiba_bluetooth:
- Add missing newline in toshiba_bluetooth_present function"
* tag 'platform-drivers-x86-v4.5-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (29 commits)
surface pro 4: fix compare_const_fl.cocci warnings
surface pro 4: Add support for Surface Pro 4 Buttons
platform:x86: Add Intel Telemetry Debugfs interfaces
platform:x86: Add Intel telemetry platform device
platform:x86: Add Intel telemetry platform driver
platform/x86: Add Intel Telemetry Core Driver
intel_punit_ipc: add NULL check for input parameters
thinkpad_acpi: Add support for keyboard backlight
dell-wmi: Process only one event on devices with interface version 0
dell-wmi: Check if Dell WMI descriptor structure is valid
tc1100-wmi: fix build warning when CONFIG_PM not enabled
asus-wireless: Add ACPI HID ATK4001
platform/x86: Add Asus Wireless Radio Control driver
asus-wmi: drop to_platform_driver macro
intel-hid: new hid event driver for hotkeys
Keyboard backlight control for some Vaio Fit models
platform/x86: Add rfkill dependency to ACPI_TOSHIBA entry
platform:x86: add Intel P-Unit mailbox IPC driver
intel_pmc_ipc: update acpi resource structure for Punit
ideapad-laptop: Add Lenovo ideapad Y700-17ISK to no_hw_rfkill dmi list
...
Move constants to the right of binary operators.
Generated by: scripts/coccinelle/misc/compare_const_fl.cocci
CC: Weng Xuetian <wengxt@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Surface Pro 4 buttons are managed by a device with _HID "MSHW0040"
different from Surface Pro 3.
This commit adds MSHW0040 to id list to support the Surface Pro 4.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=109871
Signed-off-by: Weng Xuetian <wengxt@gmail.com>
Acked-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This implements debugfs interfaces for reading the telemetry
samples from SSRAM and configuring firmware trace verbosity.
Interface created under /sys/kernel/debug/telemetry
soc_states: SoC Device and Low Power States
pss_info: Info from the Primary SubSystem
ioss_info: Info from IO SubSusytem
pss_trace_verbosity: Read/Modify PSS F/W trace verbosity
ioss_trace_verbosity: Read/Modify IOSS F/W trace verbosity.
Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Telemetry Device is created by the pmc_ipc driver. Resources
are populated according SSRAM region as indicated by the BIOS tables.
Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Telemetry platform driver implements the telemetry interfaces.
Currently it supports ApolloLake. It uses the PUNIT and PMC IPC
interfaces to configure the telemetry samples to read.
The samples are read from a Secure SRAM region.
Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Intel PM Telemetry is a software mechanism via which various SoC
PM and performance related parameters like PM counters, firmware
trace verbosity, the status of different devices inside the SoC, etc.
can be monitored and analyzed. The different samples that may be
monitored can be configured at runtime via exported APIs.
This patch adds the telemetry core driver that implements basic
exported APIs.
Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
intel_punit_ipc_command() maybe called when in or out
data pointers are NULL.
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch adds support for controlling keyboard backlight via standard
linux led class interface (::kbd_backlight). It uses ACPI HKEY device with
MLCG and MLCS methods.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Fabio D'Urso <fabiodurso@hotmail.it>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
BIOS/ACPI on devices with WMI interface version 0 does not clear buffer
before filling it. So next time when BIOS/ACPI send WMI event which is
smaller as previous then it contains garbage in buffer from previous event.
BIOS/ACPI on devices with WMI interface version 1 clears buffer and
sometimes send more events in buffer at one call.
Since commit 83fc44c32a ("dell-wmi: Update code for processing WMI
events") dell-wmi process all events in buffer (and not just first).
To prevent reading garbage from the buffer we process only the first
event on devices with WMI interface version 0.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
After examining existing DSDT ACPI tables of more laptops and looking
into Dell WMI document mentioned in ML dicussion archived at
http://www.spinics.net/lists/platform-driver-x86/msg07220.html we will
parse and check WMI descriptor if contains expected data. It is because
WMI descriptor contains interface version number and it is needed to
know in next commit.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Conditionally declare suspend_data on CONFIG_PM to avoid
the following warning when CONFIG_OM is not enabled:
drivers/platform/x86/tc1100-wmi.c:55:27: warning:
'suspend_data' defined but not used [-Wunused-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
As reported in https://bugzilla.kernel.org/show_bug.cgi?id=98931#c22 in
the Asus UX31A the Asus Wireless Radio Control device (ASHS) uses the
HID "ATK4001".
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Reported-by: Tasev Nikola <tasev.stefanoska@skynet.be>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Some Asus notebooks like the Asus E202SA and the Asus X555UB have a
separate ACPI device for notifications from the airplane mode hotkey.
This device is called "Wireless Radio Control" in Asus websites and ASHS
in the DSDT, and its ACPI _HID is ATK4002 in the two models mentioned
above.
For these models, when the airplane mode hotkey (Fn+F2) is pressed, a
query 0x0B is started in the Embedded Controller, and all this query does
is a notify ASHS with the value 0x88 (for acpi_osi >= "Windows 2012"):
Scope (_SB.PCI0.SBRG.EC0)
{
(...)
Method (_Q0B, 0, NotSerialized) // _Qxx: EC Query
{
If ((MSOS () >= OSW8))
{
Notify (ASHS, 0x88) // Device-Specific
}
Else
{
(...)
}
}
}
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Michał Kępień