By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The PHY configuration is stored in an opaque "config" field, but when
allocating the structure, its proper size needs to be known. In the case
of UTMI, the proper structure is tegra_utmip_config of which a local
variable already exists, so we can use that to obtain the size from.
Fixes the following warning from the sparse checker:
drivers/usb/phy/phy-tegra-usb.c:882:17: warning: expression using sizeof(void)
Fixes: 81d5dfe6d8 (usb: phy: tegra: Read UTMIP parameters from device tree)
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aJY4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
It is no longer needed and keeping it will break 64-bit ARM builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
tegra_usb_phy_close() is supposed to undo the effects of
tegra_usb_phy_init(). It is also currently added as the USB PHY shutdown
callback, which is wrong, since tegra_usb_phy_init() is only called
during probing wheras the shutdown callback can get called multiple
times. This then leads to warnings about unbalanced regulator_disable if
the EHCI driver is unbound and bound again at runtime.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is no longer needed and keeping it will break 64-bit ARM builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: phy-tegra-usb.c: wrong pointer check for remap UTMI
A wrong pointer was used to test the result of devm_ioremap()
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra30 TRM recommends configuration of certain PHY parameters for
optimal quality. Program the following registers based on device tree
parameters:
- UTMIP_XCVR_HSSLEW: HS slew rate control.
- UTMIP_HSSQUELCH_LEVEL: HS squelch detector level
- UTMIP_HSDISCON_LEVEL: HS disconnect detector level.
These registers exist in Tegra20, but programming them hasn't been
necessary, so these parameters won't be set on Tegra20 to keep the
device trees backward compatible.
Additionally, the UTMIP_XCVR_SETUP parameter can be set from fuses
instead of a software-programmed value, as the optimal value can
vary between invidual boards. The boolean property
nvidia,xcvr-setup-use-fuses can be used to enable this behaviour.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Tegra30 USB PHY is a bit different than the Tegra20 PHY:
- The EHCI controller supports the HOSTPC register extension, and some
of the fields that the PHY needs to modify (PHCD and PTS) have moved
to the new HOSTPC register.
- Some of the UTMI PLL configuration registers have moved from the USB
register space to the Clock-And-Reset controller space. In Tegra30
the clock driver is responsible for configuring the UTMI PLL.
- The USBMODE register must be explicitly written to enter host mode.
- Certain PHY parameters need to be programmed for optimal signal
quality. Support for this will be added in the next patch.
The new tegra_phy_soc_config structure is added to describe the
differences between the SoCs.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some of the PHY parameters are not set according to the TRMs:
- UTMIP_FS_PREABMLE_J should be set, not cleared
- UTMIP_XCVR_LSBIAS_SEL should be cleared, not set
- UTMIP_PD_CHRG should be set in host mode and cleared in device mode
- UTMIP_XCVR_SETUP is a two-part field; the upper bits were not set
properly
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use switch() instead of if-else when checking for the PHY type.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new of_usb_get_dr_mode helper function for parsing dr_mode
from the device tree. Also replace the usage of the custom
tegra_usb_phy_mode enum with the standard enum.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new of_usb_get_phy_mode helper function for parsing phy_type
from the device tree.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Tegra EHCI driver is no longer using these custom functions, so they
can be removed.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Register the Tegra PHY device instances with the PHY subsystem so that
the Tegra EHCI driver can locate a PHY via the standard APIs.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct usb_phy already has a field for the device pointer, so this
unnecessary field can be removed.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The tegra ehci driver has enabled USB vbus regulators directly using
GPIOs and the device tree attribute nvidia,vbus-gpio. This is ugly
and causes error messages on boot when both the regulator driver
and the ehci driver want access to the same GPIO.
After this patch, usb vbus regulators for tegra usb phy devices are specified
with the device tree attribute vbus-supply = <&x> where x is a regulator defined
in the device tree. The old nvidia,vbus-gpio property is no longer supported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UTMIP parameters used to be hardcoded into tables in the
PHY driver. This patch reads them from the device tree instead
in accordance with the phy-tegra-usb DT documentation.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Tegra EHCI driver directly calls various functions in the Tegra USB
PHY driver. The reverse is also true; the PHY driver calls into the EHCI
driver. This is problematic when the two are built as modules.
The calls from the PHY to EHCI driver were originally added in commit
bbdabdb "usb: add APIs to access host registers from Tegra PHY", for the
following reasons:
1) The register being touched is an EHCI register, so logically only the
EHCI driver should touch it.
2) (1) implies that some locking may be needed to correctly implement the
r/m/w access to this shared register.
3) We were expecting to pass only the PHY register space to the Tegra PHY
driver, and hence it would not have access to touch the shared
registers.
To solve this, that commit added functions in the EHCI driver to touch the
shared register on behalf of the PHY driver.
In practice, we ended up not having any locking in the implementaiton of
those functions, and I've been led to believe this is safe. Equally, (3)
did not happen either. Hence, it is possible for the PHY driver to touch
the shared register directly.
Given that, this patch moves the code to touch the shared register back
into the PHY driver, to eliminate the module problems. If we actually
need locking or co-ordination in the future, I propose we put the lock
support into some pre-existing core module, or into a third separate
module, in order to avoid the circular dependencies.
I apologize for my contribution to code churn here.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When this file is built as a module, it needs a MODULE_LICENSE in order
to access many exported symbols.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registered Tegra USB PHY as a separate platform driver.
To synchronize host controller and PHY initialization, used deferred
probe mechanism. As PHY should be initialized before EHCI starts running,
deferred probe of Tegra EHCI driver till PHY probe gets completed.
Got rid of instance number based handling in host driver.
Made use of DT params to get the PHY Pad registers.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Check return values from all GPIO APIs and handle errors accordingly.
Remove the call to clk_disable_unprepare(); this function does not
prepare or enable the clock, so the error path should not disable or
unprepare it.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As GPIO information is avail through DT, used it to get Tegra ULPI
reset GPIO number. Added a new member to tegra_usb_phy structure to
store this number.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added a new PHY mode to support OTG.
Obtained Tegra USB PHY mode using DT property.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case if clk_get_sys fails, return correct error value provided by
the API.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both phy-tegra-usb.c and ehci-tegra.c export symbols used by the other one,
which does not work if one of them or both are loadable modules, resulting
in an error like:
drivers/built-in.o: In function `utmi_phy_clk_disable':
drivers/usb/phy/phy-tegra-usb.c:302: undefined reference to `tegra_ehci_set_phcd'
drivers/built-in.o: In function `utmi_phy_clk_enable':
drivers/usb/phy/phy-tegra-usb.c:324: undefined reference to `tegra_ehci_set_phcd'
drivers/built-in.o: In function `utmi_phy_power_on':
drivers/usb/phy/phy-tegra-usb.c:447: undefined reference to `tegra_ehci_set_pts'
This turns the interface into a one-way dependency by letting the tegra ehci
driver pass two function pointers for callbacks that need to be called by
the phy driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this will make sure that we have sensible names
for all phy drivers. Current situation was already
quite bad with too generic names being used.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Heikki Krogerus