* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: fix build error in !oneshot case
x86: c1e_idle: don't mark TSC unstable if CPU has invariant TSC
x86: prevent C-states hang on AMD C1E enabled machines
clockevents: prevent mode mismatch on cpu online
clockevents: check broadcast device not tick device
clockevents: prevent stale tick_next_period for onlining CPUs
x86: prevent stale state of c1e_mask across CPU offline/online
clockevents: prevent cpu online to interfere with nohz
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix 27-rc crash on vsmp due to paravirt during module load
x86, oprofile: BUG scheduling while atomic
AMD IOMMU: protect completion wait loop with iommu lock
AMD IOMMU: set iommu sunc flag after command queuing
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] kexec fails on systems with blocks of uncached memory
[IA64] Ski simulator doesn't need check_sal_cache_flush
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix missing devices due to PCI bridge test in of_create_pci_dev().
sparc64: Fix disappearing PCI devices on e3500.
Impact: Functional TSC is marked unstable on AMD family 0x10 and 0x11 CPUs.
This would be wrong because for those CPUs "invariant TSC" means:
"The TSC counts at the same rate in all P-states, all C states, S0,
or S1"
(See "Processor BIOS and Kernel Developer's Guides" for those CPUs.)
[ tglx: Changed C1E to AMD C1E in the printks to avoid confusion
with Intel C1E ]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: System hang when AMD C1E machines switch into C2/C3
AMD C1E enabled systems do not work with normal ACPI C-states
even if the BIOS is advertising them. Limit the C-states to
C1 for the ACPI processor idle code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: hang which happens across CPU offline/online on AMD C1E systems.
When a CPU goes offline then the corresponding bit in the broadcast
mask is cleared. For AMD C1E enabled CPUs we do not reenable the
broadcast when the CPU comes online again as we do not clear the
corresponding bit in the c1e_mask, which keeps track which CPUs
have been switched to broadcast already. So on those !$@#& machines
we never switch back to broadcasting after a CPU offline/online cycle.
Clear the bit when the CPU plays dead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
27-rc fails to boot up if configured to use modules.
Turns out vsmp_patch was marked __init, and vsmp_patch being the
pvops 'patch' routine for vsmp, a call to vsmp_patch just turns out
to execute a code page with series of 0xcc (POISON_FREE_INITMEM -- int3).
vsmp_patch has been marked with __init ever since pvops, however,
apply_paravirt can be called during module load causing calls to
freed memory location.
Since apply_paravirt can only be called during init/module load, make
vsmp_patch with "__init_or_module"
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just like in the arch/sparc64/kernel/of_device.c code fix commit
071d7f4c3b411beae08d27656e958070c43b78b4 ("sparc64: Fix SMP bootup
with CONFIG_STACK_DEBUG or ftrace.") we have to check the OF device
node name for "pci" instead of relying upon the 'device_type' property
being there on all PCI bridges.
Tested by Meelis Roos, and confirmed to make the PCI QFE devices
reappear on the E3500 system.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a memory segment in memory map with attribute of EFI_MEMORY_UC
is denoted as "System RAM" in /proc/iomem, while memory of attribute
(EFI_MEMORY_WB|EFI_MEMORY_UC) is also labeled the same.
The kexec utility then includes uncached memory as part of vmcore. The
kdump kernel MCA'ed when it tries to save the vmcore to a disk. A normal
"cached" access may cause MCAs.
This patch would label memory with attribute of EFI_MEMORY_UC only as
"Uncached RAM" so that kexec would know not to include it in the vmcore.
I will submit a separate kexec-tools patch to the kexec list.
Signed-off-by: Jay Lan <jlan@sgi.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Peter Chubb reported that commit 3463a93def
(Update check_sal_cache_flush to use platform_send_ipi()) broke
Ski because it does not implement IPIs.
Tony Luck suggested we just #ifndef out the call (since the simulator
does not have the SAL bug that this code is attempting to detect and
workaround)
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The -ffunction-sections puts each text in .text.function_name section.
Without this patch, most functions are placed outside _text..._etext
area and it breaks show_stacktrace(), etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If an interrupt happened between checking of NEED_RESCHED and WAIT
instruction, adjust EPC to restart from checking of NEED_RESCHED.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use unsigned loads to avoid possible misscalculation of IP checksums. This
bug was instruced in f761106cd728bcf65b7fe161b10221ee00cf7132 (lmo) /
ed99e2bc1d (kernel.org).
[Original fix by Atsushi. Improved instruction scheduling and fix for
unaligned unsigned load by me -- Ralf]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Based upon a bug report by Meelis Roos.
The OF device layer builds properties by matching bus types and
applying 'range' properties as appropriate, up to the root.
The match for "PCI" busses is looking at the 'device_type' property,
and this does work %99 of the time.
But on an E3500 system with a PCI QFE card, the DEC 21153 bridge
sitting above the QFE network interface devices has a 'name' of "pci",
but it completely lacks a 'device_type' property. So we don't match
it as a PCI bus, and subsequently we end up with no resource values at
all for the devices sitting under that DEC bridge.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4611a77 ("[IA64] fix compile failure with non modular builds")
introduced struct fdesc into asm/elf.h, which duplicates KVM's definition.
Remove the latter to avoid the build error.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
Fix compile failure with non modular builds
powerpc: Holly board needs dtbImage target
powerpc: Fix interrupt values for DMA2 in MPC8610 HPCD device tree
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5255/1: Update jornada ssp to remove build errors/warnings
[ARM] omap: back out 'internal_clock' support
[ARM] 5249/1: davinci: remove redundant check in davinci_psc_config()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix SMP bootup with CONFIG_STACK_DEBUG or ftrace.
sparc64: Fix OOPS in psycho_pcierr_intr_other().
While updating the rcu code, I noticed that do_nmi() for AVR32 is odd:
There is an nmi_enter() call without an nmi_exit().
This can't be correct, it breaks rcu (at least the preempt version) and
lockdep.
[haavard.skinnemoen@atmel.com: fixed another case that returned directly]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On AVR32, all parameters beyond the 5th are passed on the stack. System
calls don't use the stack -- they borrow a callee-saved register
instead. This means that syscalls that take 6 parameters must be called
through a stub that pushes the last parameter on the stack.
This patch adds a stub for sync_file_range syscall on AVR32
architecture. Tested with uClibc snapshot.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch implements the generic_find_next_le_bit bit function for AVR32
architecture. This is used by EXT4 file system.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The #ifdef surrounding the code adding the mmc controller had a typo,
causing it to be compiled even when mmc was supposed to be disabled.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* Adds ssp functions into header so we don't get
"implicit declaration" error at builtime.
* Converts jornada_ssp_start/end functions into voids with
proper declarations (to avoid "prototype..." warning).
* Sorts include files in alphabetical order
* Minor comment changes
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The unlocked polling of the ComWaitInt bit in the IOMMU completion wait
path is racy. Protect it with the iommu lock.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The iommu->need_sync flag must be set after the command is queued to
avoid race conditions.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The structures weren't ready for this change:
arch/arm/plat-omap/devices.c:320: error: 'struct omap_mmc_conf' has no member named 'internal_clock'
arch/arm/plat-omap/devices.c:326: error: implicit declaration of function 'omap_ctrl_readl'
arch/arm/plat-omap/devices.c:326: error: 'OMAP2_CONTROL_DEVCONF0' undeclared (first use in this function)
arch/arm/plat-omap/devices.c:328: error: implicit declaration of function 'omap_ctrl_writel'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit deac93df26 ("lib: Correct printk
%pF to work on all architectures") broke the non modular builds by
moving an essential function into modules.c. Fix this by moving it
out again and into asm/sections.h as an inline. To do this, the
definition of struct ppc64_opd_entry has been lifted out of modules.c
and put in asm/elf.h where it belongs.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
One of the changes in the bootwrapper makefile introduced the dtbImage
targets for boards that need a simple zImage with a DTB embedded in
them (595be948cc, "[POWERPC]
bootwrapper: Build multiple cuImages"). When this was done, it broke
booting on the Holly board as the zImage.holly wrapper did not get the
DTB embedded properly.
This changes the target for the Holly board to a dtbImage so that the
wrapper includes the vmlinux, wrapper bits, and DTB.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For Freescale 8xxx devices that use an MPIC, the interrupt numbers in
the device tree must be 16 greater than the values documented in the
reference manual. In these chips, the MPIC is wired to use the first
16 numbers for external interrupts, but the documentation numbers
internal interrupts from 0.
In the MPC8610 HPCD device tree, the interrupt properties for the DMA
channels for DMA2 were not the adjusted values. This fixes that.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Based upon a report by Meelis Roos.
Any function call can try to access the current
thread register via the _mcount hooks when the kernel
is built with -pg (via ftrace or STACK_DEBUG).
That can't be setup properly very early on during
the bootup of other cpus for sun4u and some early
sun4v systems.
So add notrace markers to these specific functions, so
that _mcount doesn't get invoked too early.
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer put the top-level PCI controller device into the
PCI layer device list. So pbm->pci_bus->self is always NULL.
Therefore, use direct PCI config space accesses to get at
the PCI controller's PCI_STATUS register.
Tested by Meelis Roos.
Signed-off-by: David S. Miller <davem@davemloft.net>
Completely disable NOPL on 32 bits. It turns out that Microsoft
Virtual PC is so broken it can't even reliably *fail* in the presence
of NOPL.
This leaves the infrastructure in place but disables it
unconditionally.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
They were already called once in arch/x86/kernel/setup.c - we don't need to call them again.
fixes:
http://bugzilla.kernel.org/show_bug.cgi?id=11485
Signed-off-by: Alex Nixon <alex.nixon@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
PFN_PHYS() can truncate large addresses unless its passed a suitable
large type. This is fixed more generally in the patch series
introducing phys_addr_t, but we need a short-term fix to solve a
Xen regression reported by Roberto De Ioris.
Reported-by: Roberto De Ioris <roberto@unbit.it>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] Fix PCI_DMA_BUS_IS_PHYS for ARM
[ARM] 5247/1: tosa: SW_EAR_IN support
[ARM] 5246/1: tosa: add proper clock alias for tc6393xb clock
[ARM] 5245/1: Fix warning about unused return value in drivers/pcmcia
[ARM] OMAP: Fix MMC device data
imx serial: fix rts handling for non imx1 based hardware
imx serial: set RXD mux bit on i.MX27 and i.MX31
i.MX serial: fix init failure
pcm037: add rts/cts support for serial port
PCI_DMA_BUS_IS_PHYS was defined to be zero, which meant we ignored
the DMA mask for IDE and SCSI transfers. This is wrong - we have
no DMA translation hardware. We want to obey DMA masks so that the
block layer performs bouncing itself.
Reported-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add clock alias for clock that is used by tc6393xb device on tosa.
As that chip plays pretty major part in tosa life and is currently
disabled, this is 2.4.27 material.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As noticed by Russell King, we were not setting this properly
to the number of entries, but rather the total size.
This results in the core dumping code allocating waayyyy too
much memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to pass IRQF_SHARED, otherwise we get things like:
IRQ handler type mismatch for IRQ 33
current handler: PSYCHO_UE
Call Trace:
[000000000048394c] request_irq+0xac/0x120
[00000000007c5f6c] psycho_scan_bus+0x98/0x158
[00000000007c2bc0] pcibios_init+0xdc/0x12c
[0000000000426a5c] do_one_initcall+0x1c/0x160
[00000000007c0180] kernel_init+0x9c/0xfc
[0000000000427050] kernel_thread+0x30/0x60
[00000000006ae1d0] rest_init+0x10/0x60
on e3500 and similar systems.
On a single board, the UE interrupts of two Psycho nodes
are funneled through the same interrupt, from of_debug=3
dump:
/pci@b,4000: direct translate 2ee --> 21
...
/pci@b,2000: direct translate 2ee --> 21
Decimal "33" mentioned above is the hex "21" mentioned here.
Thanks to Meelis Roos for dumps and testing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Russ Anderson reported a boot crash with EFI and latest mainline:
BIOS-e820: 00000000fffa0000 - 00000000fffac000 (reserved)
Pid: 0, comm: swapper Not tainted 2.6.27-rc5-00100-gec0c15a-dirty #5
Call Trace:
[<ffffffff80849195>] early_idt_handler+0x55/0x69
[<ffffffff80313e52>] __memcpy+0x12/0xa4
[<ffffffff80859015>] efi_init+0xce/0x932
[<ffffffff80869c83>] setup_early_serial8250_console+0x2d/0x36a
[<ffffffff80238688>] __insert_resource+0x18/0xc8
[<ffffffff8084f6de>] setup_arch+0x3a7/0x632
[<ffffffff808499ed>] start_kernel+0x91/0x367
[<ffffffff80849393>] x86_64_start_kernel+0xe3/0xe7
[<ffffffff808492b0>] x86_64_start_kernel+0x0/0xe7
RIP 0x10
Such a crash is possible if the CPU in this system is a 64-bit
processor which doesn't support NX (ie, old Intel P4 -based64-bit
processors).
Certainly, if we support such processors, then we should start with
_PAGE_NX initially clear in __supported_pte_flags, and then set it once
we've established that the processor does indeed support NX. That will
prevent early_ioremap - or anything else - from trying to set it.
The simple fix is to simply call check_efer() earlier.
Reported-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change the MN10300 fault handler to make it check in_atomic() rather than
in_interrupt() as commit 6edaf68a87 did for other
architectures:
Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Wed Dec 6 20:32:18 2006 -0800
[PATCH] mm: arch do_page_fault() vs in_atomic()
In light of the recent pagefault and filemap_copy_from_user work I've
gone through all the arch pagefault handlers to make sure the
inc_preempt_count() 'feature' works as expected.
Several sections of code (including the new filemap_copy_from_user)
rely on the fact that faults do not take locks under increased preempt
count.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'kvm-updates/2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: VMX: Always return old for clear_flush_young() when using EPT
KVM: SVM: fix guest global tlb flushes with NPT
KVM: SVM: fix random segfaults with NPT enabled
OMAPs MMC device data was passing the wrong structure via the platform
device. Moreover, a missing function means that both sx1_defconfig
and omap_h2_1610_defconfig builds failed with
undefined reference to `omap_set_mmc_info'
errors. Fix this by updating the MMC support from the omapzoom tree.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As well as discard fake accessed bit and dirty bit of EPT.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Accesses to CR4 are intercepted even with Nested Paging enabled. But the code
does not check if the guest wants to do a global TLB flush. So this flush gets
lost. This patch adds the check and the flush to svm_set_cr4.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch introduces a guest TLB flush on every NPF exit in KVM. This fixes
random segfaults and #UD exceptions in the guest seen under some workloads
(e.g. long running compile workloads or tbench). A kernbench run with and
without that fix showed that it has a slowdown lower than 0.5%
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Use the IMAP offset calculation for OBIO devices as documented in the
programmer's manual. Which is "0x10000 + ((ino & 0x1f) << 3)"
Signed-off-by: David S. Miller <davem@davemloft.net>
Make ia64 refrain from clearing a given to-be-offlined CPU's bit in the
cpu_online_mask until it has processed pending irqs. This change
prevents other CPUs from being blindsided by an apparently offline CPU
nevertheless changing globally visible state. Also remove the existing
redundant cpu_clear(cpu, cpu_online_map).
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Error handling code following a kmalloc should free the allocated data.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tony Luck <tony.luck@intel.com>
bte.h expects a #define of L1_CACHE_MASK which is currently only
in bte.c. This small patch gets bte.h to include cleanly and makes
BTE_UNALIGNED_COPY not report errors.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Broke the non modular builds by moving an essential function into
modules.c. Fix this by moving it out again and into asm/sections.h as
an inline. To do this, the definitions of struct fdesc and struct
got_val have been lifted out of modules.c and put in asm/elf.h where
they belong.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Error handling code following a kmalloc should free the allocated data.
Note that at the point of the change, node has not yet been stored in d, so
it is not affected by the existing cleanup code.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It was introduced by "vsprintf: add support for '%pS' and '%pF' pointer
formats" in commit 0fe1ef24f7. However,
the current way its coded doesn't work on parisc64. For two reasons: 1)
parisc isn't in the #ifdef and 2) parisc has a different format for
function descriptors
Make dereference_function_descriptor() more accommodating by allowing
architecture overrides. I put the three overrides (for parisc64, ppc64
and ia64) in arch/kernel/module.c because that's where the kernel
internal linker which knows how to deal with function descriptors sits.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When running a 31-bit ptrace, on either an s390 or s390x kernel,
reads and writes into a padding area in struct user_regs_struct32
will result in a kernel panic.
This is also known as CVE-2008-1514.
Test case available here:
http://sources.redhat.com/cgi-bin/cvsweb.cgi/~checkout~/tests/ptrace-tests/tests/user-area-padding.c?cvsroot=systemtap
Steps to reproduce:
1) wget the above
2) gcc -o user-area-padding-31bit user-area-padding.c -Wall -ggdb2 -D_GNU_SOURCE -m31
3) ./user-area-padding-31bit
<panic>
Test status
-----------
Without patch, both s390 and s390x kernels panic. With patch, the test case,
as well as the gdb testsuite, pass without incident, padding area reads
returning zero, writes ignored.
Nb: original version returned -EINVAL on write attempts, which broke the
gdb test and made the test case slightly unhappy, Jan Kratochvil suggested
the change to return 0 on write attempts.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a CPU is offlined, we leave the timer interrupts disabled
because fixup_irqs() does not explicitly take care of that case.
Fix this by invoking tick_ops->disable_irq().
Based upon analysis done by Paul E. McKenney.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: pm_standby low-power ram bug fix
avr32: Fix lockup after Java stack underflow in user mode
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix rare boot build breakage
powerpc/spufs: Fix possible scheduling of a context to multiple SPEs
powerpc/spufs: Fix race for a free SPU
powerpc/spufs: Fix multiple get_spu_context()
On 32-bit, at least the generic nops are fairly reasonable, but the
default nops for 64-bit really look pretty sad, and the P6 nops really do
look better.
So I would suggest perhaps moving the static P6 nop selection into the
CONFIG_X86_64 thing.
The alternative is to just get rid of that static nop selection, and just
have two cases: 32-bit and 64-bit, and just pick obviously safe cases for
them.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The second HPC3 could be found only on Guiness systems (Challenge-S),
but not on fullhouse (Indigo2) systems.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A make -j20 powerpc kernel build broke a couple of months ago saying:
In file included from arch/powerpc/boot/gunzip_util.h:13,
from arch/powerpc/boot/prpmc2800.c:21:
arch/powerpc/boot/zlib.h:85: error: expected ‘:’, ‘,’, ‘;’, ‘}’ or ‘__attribute__’ before ‘*’ token
arch/powerpc/boot/zlib.h:630: warning: type defaults to ‘int’ in declaration of ‘Byte’
arch/powerpc/boot/zlib.h:630: error: expected ‘;’, ‘,’ or ‘)’ before ‘*’ token
It happened again yesterday: too rare for me to confirm the fix, but
it looks like the list of dependants on gunzip_util.h was incomplete.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a race when scheduling a context to a SPE -
after we have found a runnable context in spusched_tick, the same
context may have been scheduled by spu_activate().
This may result in a panic if we try to unschedule a context that has
been freed in the meantime.
This change exits spu_schedule() if the context has already been
scheduled, so we don't end up scheduling it twice.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: cpu_init(): fix memory leak when using CPU hotplug
x86: pda_init(): fix memory leak when using CPU hotplug
x86, xen: Use native_pte_flags instead of native_pte_val for .pte_flags
x86: move mtrr cpu cap setting early in early_init_xxxx
x86: delay early cpu initialization until cpuid is done
x86: use X86_FEATURE_NOPL in alternatives
x86: add NOPL as a synthetic CPU feature bit
x86: boot: stub out unimplemented CPU feature words
Exception stacks are allocated each time a CPU is set online.
But the allocated space is never freed. Thus with one CPU hotplug
offline/online cycle there is a memory leak of 24K (6 pages) for
a CPU.
Fix is to allocate exception stacks only once -- when the CPU is
set online for the first time.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: akpm@linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
pda->irqstackptr is allocated whenever a CPU is set online.
But it is never freed. This results in a memory leak of 16K
for each CPU offline/online cycle.
Fix is to allocate pda->irqstackptr only once.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: akpm@linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Using native_pte_val triggers the BUG_ON() in the paravirt_ops
version of pte_flags().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Krzysztof Helt found MTRR is not detected on k6-2
root cause:
we moved mtrr_bp_init() early for mtrr trimming,
and in early_detect we only read the CPU capability from cpuid,
so some cpu doesn't have that bit in cpuid.
So we need to add early_init_xxxx to preset those bit before mtrr_bp_init
for those earlier cpus.
this patch is for v2.6.27
Reported-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move early cpu initialization after cpu early get cap so the
early cpu initialization can fix up cpu caps.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch provides an ARM implementation of ioremap_wc().
We use different page table attributes depending on which CPU we
are running on:
- Non-XScale ARMv5 and earlier systems: The ARMv5 ARM documents four
possible mapping types (CB=00/01/10/11). We can't use any of the
cached memory types (CB=10/11), since that breaks coherency with
peripheral devices. Both CB=00 and CB=01 are suitable for _wc, and
CB=01 (Uncached/Buffered) allows the hardware more freedom than
CB=00, so we'll use that.
(The ARMv5 ARM seems to suggest that CB=01 is allowed to delay stores
but isn't allowed to merge them, but there is no other mapping type
we can use that allows the hardware to delay and merge stores, so
we'll go with CB=01.)
- XScale v1/v2 (ARMv5): same as the ARMv5 case above, with the slight
difference that on these platforms, CB=01 actually _does_ allow
merging stores. (If you want noncoalescing bufferable behavior
on Xscale v1/v2, you need to use XCB=101.)
- Xscale v3 (ARMv5) and ARMv6+: on these systems, we use TEXCB=00100
mappings (Inner/Outer Uncacheable in xsc3 parlance, Uncached Normal
in ARMv6 parlance).
The ARMv6 ARM explicitly says that any accesses to Normal memory can
be merged, which makes Normal memory more suitable for _wc mappings
than Device or Strongly Ordered memory, as the latter two mapping
types are guaranteed to maintain transaction number, size and order.
We use the Uncached variety of Normal mappings for the same reason
that we can't use C=1 mappings on ARMv5.
The xsc3 Architecture Specification documents TEXCB=00100 as being
Uncacheable and allowing coalescing of writes, which is also just
what we need.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After fixing the u32 thinko I sill had occasional hickups on ATI chipsets
with small deltas. There seems to be a delay between writing the compare
register and the transffer to the internal register which triggers the
interrupt. Reading back the value makes sure, that it hit the internal
match register befor we compare against the counter value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We use the HPET only in 32bit mode because:
1) some HPETs are 32bit only
2) on i386 there is no way to read/write the HPET atomic 64bit wide
The HPET code unification done by the "moron of the year" did
not take into account that unsigned long is different on 32 and
64 bit.
This thinko results in a possible endless loop in the clockevents
code, when the return comparison fails due to the 64bit/332bit
unawareness.
unsigned long cnt = (u32) hpet_read() + delta can wrap over 32bit.
but the final compare will fail and return -ETIME causing endless
loops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use X86_FEATURE_NOPL to determine if it is safe to use P6 NOPs in
alternatives. Also, replace table and loop with simple if statement.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The long noops ("NOPL") are supposed to be detected by family >= 6.
Unfortunately, several non-Intel x86 implementations, both hardware
and software, don't obey this dictum. Instead, probe for NOPL
directly by executing a NOPL instruction and see if we get #UD.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The CPU feature detection code in the boot code is somewhat minimal,
and doesn't include all possible CPUID words. In particular, it
doesn't contain the code for CPU feature words 2 (Transmeta),
3 (Linux-specific), 5 (VIA), or 7 (scattered). Zero them out, so we
can still set those bits as known at compile time; in particular, this
allows creating a Linux-specific NOPL flag and have it required (and
therefore resolvable at compile time) in 64-bit mode.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* git://git.infradead.org/~dwmw2/dwmw2-2.6.27:
Revert "[ARM] use the new byteorder headers"
Fix conditional export of kvh.h and a.out.h to userspace.
[MTD] [NAND] tmio_nand: fix base address programming
