It's perfectly valid to use SMP on a non-MT CPU and use the GIC for
IPIs. Set them up conditional upon CONFIG_MIPS_GIC_IPI rather than
CONFIG_MIPS_MT_SMP.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/6654/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Shift System Controller memory mapping to 0x80000000
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Use a Malta specific function to free the init section once the
kernel has booted. When operating in EVA mode, the physical memory
is shifted to 0x80000000. Kernel is loaded into 0x80000000 (virtual)
so the offset between physical and virtual addresses is 0.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
PHYS_OFFSET is used to denote the physical start address of the
first bank of RAM. When the Malta board is in EVA mode, the physical
start address of RAM is shifted to 0x80000000 so it's necessary to use
this macro in order to make the code EVA agnostic.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The 'ememsize' variable is used to denote the real RAM which is
present on the Malta board. This is different compared to 'memsize'
which is capped to 256MB. The 'ememsize' is used to get the actual
physical memory when setting up the Malta memory layout. This only
makes sense in case the core operates in the EVA mode, and it's
ignored otherwise.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The Malta board aliases 0x80000000 - 0xffffffff to 0x00000000
- 0x7fffffff ignoring the 256 MB IO hole in 0x10000000.
The physical memory is shifted to 0x80000000 so up to 2GB
can be used. Kuseg is expanded to 3GB (due to board limitations
only 2GB can be accessed) and lowmem (kernel space) is expanded to 2GB.
The Segment Control registers are programmed as follows:
Virtual memory Physical memory Mapping
0x00000000 - 0x7fffffff 0x80000000 - 0xfffffffff MUSUK (kuseg)
0x80000000 - 0x9fffffff 0x00000000 - 0x1ffffffff MUSUK (kseg0)
0xa0000000 - 0xbf000000 0x00000000 - 0x1ffffffff MUSUK (kseg1)
0xc0000000 - 0xdfffffff - MK (kseg2)
0xe0000000 - 0xffffffff - MK (kseg3)
The location of exception vectors remain the same since 0xbfc00000
(traditional exception base) still maps to 0x1fc00000 physical.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
This patch simply attempts to register the MIPS Coherent Processing
System SMP implementation when it is enabled. If registering that fails
for some reason (like the Kconfig option being disabled or a lack of
hardware support) then we fall back to the same SMP implementations as
before.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6365/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When CPC support is compiled into the kernel (ie. CONFIG_MIPS_CPC=y),
probe the CPC on boot for Malta in order to allow any users of the CPC
to detect its presence & function correctly.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the Malta-specific CM probe code and instead make use of the
newly added generic CM code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now we have CONFIG_MIPS_VPE_LOADER and CONFIG_MIPS_VPE_LOADER_[CMP|MT]. The
latter two are used by the 2 exclusive flavors. The vpe_run in malta-amon.c
is for CMP APRP. Without the fix, this vpe_run will be used in MT APRP.
Reviewed-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: john@phrozen.org
Patchwork: https://patchwork.linux-mips.org/patch/6589/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are 2 errors with the existing aprp_hook linking:
- The prefix CONFIG_ is missing;
- The hook should be linked exclusively in the cases of MT and CMP.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Reviewed-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: john@phrozen.org
Patchwork: https://patchwork.linux-mips.org/patch/6588/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6320/
This patch switches Malta from using the MIPS implementation of early
printk with Malta's prom_putchar to using the generic 8250_early
implementation. This offers a couple of advantages:
- We duplicate less generic code.
- The UART can be initialised rather than being reliant upon
inheriting a valid setup from the bootloader.
The Malta console_config function is extended to initialise the early
console if no earlycon= kernel parameter is provided, inheriting the
modetty0 bootloader environment if present and falling back to a
default 38400n8r setup if not. This matches the behaviour used for the
regular console= parameter.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6183/
The RTC is used on Malta to estimate the clock frequency of the CPU &
optionally the GIC. However the kernel previously did not initialise the
RTC, instead relying upon the bootloader having done so. In order to
minimise dependencies which the kernel has upon the bootloader this
patch causes the kernel to initialise the RTC itself prior to making use
of it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6184/
This variable was introduced by commit 96348c8f (of Ralf's historic
Linux/MIPS repository) "Remaining fixes for MIPS's eval boards." but
I don't see any use of it either then or now. Remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6171/
Clean-up code according to the 'checkpatch.pl' script.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6097/
Reviewed-by: John Crispin <blogic@openwrt.org>
Malta with multi-core CM platforms can now use APRP functionality.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6096/
Commit 225ae5fd9a
"MIPS: Malta: Fix interupt number of CBUS UART"
fixed the IRQ number for the ttyS2 CBUS UART. However, this now
conflicts with the GIC IPI1 interrupt in CMP platforms. The Malta
interrupt code arbitrarily binds IPIs to INT2 and INT3 and since
ttyS2 uses the INT2 IRQ line, closing the device disables the
INT2 interrupt and this effectively disables the IPI1 interrupt
as well. This patch is mainly a workaround until the Malta code
is fixed properly.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6045/
Pull MIPS updates from Ralf Baechle:
- Some minor work bringing the Cobalt MIPS platforms in line with other
MIPS platforms
- Make vmlinux.32 and vmlinux.64 build messages less verbose
- Always register the R4k clocksource when selected, the clock source's
rating will decide if this or another clock source is actually going
to be used
- Drop support for the Cisco (formerly Scientific Atlanta) PowerTV
platform. There appears to be nobody left who cares and the USB
driver went stale while waiting for years to be merged
- Some cleanup of Loongson 2 related #ifdefery
- Various minor cleanups
- Major rework on all things related to tracing / ptrace on MIPS,
including switching the MIPS ELF core dumper to regsets, enabling the
entries for SIGSYS in struct siginfo for MIPS, enabling ftrace
syscall trace points
- Some more work to bring DECstation support code in line with other
more modern code
- Report the name of the detected CPU, not just its CP0 PrID value
- Some more BCM 47xx and atheros ath79xx work
- Support for compressed kernels using the XZ compression scheme
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (53 commits)
MIPS: remove duplicate define
MIPS: Random whitespace clean-ups
MIPS: traps: Reformat notify_die invocations to 80 columns.
MIPS: Print correct PC in trace dump after NMI exception
MIPS: kernel: cpu-probe: Report CPU id during probe
MIPS: Remove unused defines in piix4.h
MIPS: Get rid of hard-coded values for Malta PIIX4 fixups
MIPS: Always register R4K clock when selected
MIPS: Loongson: Get rid of Loongson 2 #ifdefery all over arch/mips.
MIPS: cacheops.h: Increase indentation by one tab.
MIPS: Remove bogus BUG_ON()
MIPS: PowerTV: Remove support code.
MIPS: ftrace: Add support for syscall tracepoints.
MIPS: ptrace: Switch syscall reporting to tracehook_report_syscall_entry().
MIPS: Move audit_arch() helper function to __syscall_get_arch().
MIPS: Enable HAVE_ARCH_TRACEHOOK.
MIPS: Switch ELF core dumper to use regsets.
MIPS: Implement task_user_regset_view.
MIPS: ptrace: Use tracehook helpers.
MIPS: O32 / 32-bit: Always copy 4 stack arguments.
...
The GIC interrupt offsets are calculated based on the value of NR_CPUS.
However, this is wrong because NR_CPUS may or may not contain the real
number of the actual cpus present in the system. We fix that by using
the 'nr_cpu_ids' variable which contains the real number of cpus in
the system. Previously, an MT core (eg with 8 VPEs) will fail to boot if
NR_CPUS was > 8 with the following errors:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/irq/chip.c:670 __irq_set_handler+0x15c/0x164()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.12.0-rc5-00087-gced5633 5
Stack : 00000006 00000004 00000000 00000000 00000000 00000000 807a4f36 00000053
807a0000 00000000 80173218 80565aa8 00000000 00000000 00000000 0000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 0000000
00000000 00000000 00000000 8054fd00 8054fd94 80500514 805657a7 8016eb4
807a0000 80500514 00000000 00000000 80565aa8 8079a5d8 80565766 8054fd0
...
Call Trace:
[<801098c0>] show_stack+0x64/0x7c
[<8049c6b0>] dump_stack+0x64/0x84
[<8012efc4>] warn_slowpath_common+0x84/0xb4
[<8012f00c>] warn_slowpath_null+0x18/0x24
[<80173218>] __irq_set_handler+0x15c/0x164
[<80587cf4>] arch_init_ipiirq+0x2c/0x3c
[<805880c8>] arch_init_irq+0x3c4/0x4bc
[<80588e28>] init_IRQ+0x3c/0x50
[<805847e8>] start_kernel+0x230/0x3d8
---[ end trace 4eaa2a86a8e2da26 ]---
This is now fixed and the Malta board can boot with any NR_CPUS value
which also helps supporting more processors in a single kernel binary.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6091/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PIIX4_ICTLR* and PIIX4_OCW* defines are not used by any other files.
Remove them.
The only file (other than fixup-malta.c which includes piix4.h in patch #1)
containing "#include <asm/mips-boards/piix4.h>" is
arch/mips/mti-malta/malta-int.c whose first version is actually
"1da177e4c3:arch/mips/mips-boards/malta/malta_int.c". In that version, in
the function get_int(), things in piix4.h are used. But now malta-int.c no
longer needs those stuff.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace hardcoded CP0 PRId and CP1 FPIR register access masks throughout.
The change does not touch places that use shifted or partial masks.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 3747069b25e419f6b51395f48127e9812abc3596 upstream.
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
Here, we remove all the MIPS __cpuinit from C code and __CPUINIT
from asm files. MIPS is interesting in this respect, because there
are also uasm users hiding behind their own renamed versions of the
__cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
[ralf@linux-mips.org: Folded in Paul's followup fix.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5494/
Patchwork: https://patchwork.linux-mips.org/patch/5495/
Patchwork: https://patchwork.linux-mips.org/patch/5509/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add GCMP detection for IASim Marvell chip emulation support.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/5529/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the software reset register and reset value definitions
from the 'include/asm/mips-boards/generic.h' header file. Also
clean up header and whitespace in platform file.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5456/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove usage of 'include/asm/mips-boards/generic.h' header file.
Instead, move the defines for SOFTRES_REG and GORESET local to
the platform file.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5455/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add new clockevent driver that uses the counter present on the MIPS
Global Interrupt Controller.
Signed-off-by: Raghu Gandham <Raghu.Gandham@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reorganize some of the GIC clocksource driver code. Below is a list of
the various changes.
* No longer select CSRC_GIC by default for Malta platform.
* Limit choice for either the GIC or R4K clocksource, not both.
* Change location in Makefile.
* Created new 'gic_read_count' function in common 'irq-gic.c' file.
* Change 'git_hpt_read' function in 'csrc-gic.c' to use new function.
* Surround GIC specific code in Malta platform code with #ifdef's.
* Only initialize the GIC clocksource if it was selected. Original
code called it unconditionally if a GIC was found.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Move the global variable 'gic_frequency' to be defined in the file
'arch/mips/kernel/irq-gic.c' instead of defining it individually
for each platform making use of the GIC. Also change the type to
be an unsigned integer instead of signed.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Move the global variable 'gic_present' to be defined in the file
'arch/mips/kernel/irq-gic.c' instead of defining it individually
for each platform making use of the GIC. Also change the type to
be an unsigned integer instead of signed.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Remove 'arch/mips/include/asm/mips-boards/prom.h' and get rid of
all inclusions of it by Malta and SEAD-3 platforms.
[ralf@linux-mips.org: Fold in John Crispin <blogic@openwrt.org>'s "MIPS:
ar7 powertv build"].
[ralf@linux-mips.org: Fold in John Crispin <blogic@openwrt.org>'s "MIPS:
unbreak powertv build"].
[ralf@linux-mips.org: Test. Build. Your. Fscking. Code. Or...]
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
- Add the KVM option to MIPS build files.
- Add default config files for KVM host/guest kernels.
- Change the link address for the Malta KVM Guest kernel to UM (0x40100000).
- Add KVM Kconfig file with KVM/MIPS specific options
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some MIPS controllers have hardware I/O coherency. This patch
detects those and turns off software coherency. A new kernel
command line option also allows the user to manually turn
software coherency on or off.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Add new clocksource that uses the counter present on the MIPS
Global Interrupt Controller.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Patchwork: http://patchwork.linux-mips.org/patch/4681/
Signed-off-by: John Crispin <blogic@openwrt.org>
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CBUS UART's interrupt number was wrong conflicting with the interrupt
being tied to the Intel PIIX4. Since the PIIX4's interrupt is registered
before the CBUS UART which is not being used on most systems this would
not be noticed.
Attempts to open the ttyS2 CBUS UART would result in:
genirq: Flags mismatch irq 18. 00000000 (serial) vs. 00010000 (XT-PIC cascade)
serial_link_irq_chain: request failed: -16 for irq: 18
Qemu was written to match the kernel so will need to be fixed also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
YAMON requires and enforces the RTC Data Mode (Register B, DM bit) to
binary, that is the bit is set every time the board goes through the
firmware bootstrap sequence. Likewise its calendar manipulation commands
interpret or set the RTC registers unconditionally as binary, never
actually checking what the value of the DM bit is, under the (correct)
assumption that it has been previously set, to indicate the binary mode.
A change to Linux a while ago however introduced a platform-specific
tweak that clears that bit and therefore forces the data mode to BCD.
This causes clock corruption and misinterpretation that has to be fixed up
by user-mode tools in system startup scripts as the initial clock is often
incorrect according to the BCD interpretation forced.
This change removes the hack; a comment included refers to alarm code,
but even if it was broken at one point by requiring the BCD mode, it
should have been trivially corrected and even if not, given how rarely the
alarm feature is used, that was not really a reasonable justification to
break the system clock that is indeed used by virtually everything. And
either way the alarm code has been since fixed anyway.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4336/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GIC interrupt code is used by multiple platforms and the
current code was half Malta dependent code. These changes
abstract away the platform specific differences.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
2ec8663f9c03a96f2c328c7c483603c31d62ad37 (lmo) rsp.
497e5ff03f (kernel.org) [MIPS: Malta: Move
PIIX4 PCI fixup to where it belongs.] attempted to move this PCI fixup
but really only added it at it's new location without deleting the old
instance.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixups are executed once the pci-device is found which is during boot
process so __init seems fine as long as the platform does not support
hotplug.
However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.
[ralf@linux-mips.org: Made piixirqmap[] in malta_piix_func0_fixup()
__initdata.]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel@pengutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/3565/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled and we even check
and yell when an interrupt handler returns with interrupts enabled (see
commit [b738a50a: genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
[ralf@linux-mips.org: Fixed up conflicts in
arch/mips/alchemy/common/dbdma.c, arch/mips/cavium-octeon/smp.c and
arch/mips/kernel/perf_event.c.]
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: tglx@linutronix.delinux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2835/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mark interrupts with no_action handler, cascade interrupts, low level
interrupts (bus error, halt ..) with IRQF_NO_THREAD to exclude them
from forced threading.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 6be63bbbda (lmo) rsp.
af3a1f6f48 (kernel.org) the Malta code does
no longer probe for presence of GCMP if CMP is not configured. This means
that the variable gcmp_present well be left at its default value of -1
which normally is meant to indicate that GCMP has not yet been mmapped.
This non-zero value is now interpreted as GCMP being present resulting
in a write attempt to a GCMP register resulting in a crash.
Reported and a build fix on top of my fix by Rob Landley <rob@landley.net>.
Reported-by: Rob Landley <rob@landley.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2413/
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (60 commits)
sched: Fix and optimise calculation of the weight-inverse
sched: Avoid going ahead if ->cpus_allowed is not changed
sched, rt: Update rq clock when unthrottling of an otherwise idle CPU
sched: Remove unused parameters from sched_fork() and wake_up_new_task()
sched: Shorten the construction of the span cpu mask of sched domain
sched: Wrap the 'cfs_rq->nr_spread_over' field with CONFIG_SCHED_DEBUG
sched: Remove unused 'this_best_prio arg' from balance_tasks()
sched: Remove noop in alloc_rt_sched_group()
sched: Get rid of lock_depth
sched: Remove obsolete comment from scheduler_tick()
sched: Fix sched_domain iterations vs. RCU
sched: Next buddy hint on sleep and preempt path
sched: Make set_*_buddy() work on non-task entities
sched: Remove need_migrate_task()
sched: Move the second half of ttwu() to the remote cpu
sched: Restructure ttwu() some more
sched: Rename ttwu_post_activation() to ttwu_do_wakeup()
sched: Remove rq argument from ttwu_stat()
sched: Remove rq->lock from the first half of ttwu()
sched: Drop rq->lock from sched_exec()
...
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix rt_rq runtime leakage bug
CC arch/mips/mti-malta/malta-int.o
arch/mips/mti-malta/malta-int.c: In function 'mips_pcibios_iack':
arch/mips/mti-malta/malta-int.c:59:6: error: variable 'dummy' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/mti-malta/malta-init.o
arch/mips/mti-malta/malta-init.c: In function 'prom_init':
arch/mips/mti-malta/malta-init.c:196:6: error: variable 'result' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For future rework of try_to_wake_up() we'd like to push part of that
function onto the CPU the task is actually going to run on.
In order to do so we need a generic callback from the existing scheduler IPI.
This patch introduces such a generic callback: scheduler_ipi() and
implements it as a NOP.
BenH notes: PowerPC might use this IPI on offline CPUs under rare conditions!
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110405152728.744338123@chello.nl
Add missing #inclusions of <linux/irq.h> to a whole bunch of files that should
really include it. Note that this can replace #inclusions of <asm/irq.h>.
This is required for the patch to sort out irqflags handling function naming to
compile on MIPS.
The problem is that these files require access to things like setup_irq() -
which isn't available by #including <linux/interrupt.h>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Several MIPS platforms don't set pci_controller::io_map_base for their
PCI bridges. This results in a panic in pci_iomap(). (The panic is
conditional on CONFIG_PCI_DOMAINS, but that is now enabled for all PCI
MIPS systems.)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: linux-mips@linux-mips.org
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: 584784@bugs.debian.org
Patchwork: https://patchwork.linux-mips.org/patch/1377/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The MIPS-specific macro CL_SIZE is merely aliasing the macro
COMMAND_LINE_SIZE. Other architectures use the latter; also,
COMMAND_LINE_SIZE is documented in kernel-parameters.txt, so
let's use it, and remove the alias.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit 22242681cf ("MIPS: Extend
COMMAND_LINE_SIZE"), CL_SIZE is 4096 and local array variables with this
size will cause an build failure with default CONFIG_FRAME_WARN settings.
Although current users of such array variables are all early bootstrap
code and not likely to cause real stack overflow (thread_info corruption),
it is preferable to to declare these arrays static with __initdata.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes the remaining problems introduced by
f197465384 (incorrect access length &
byteswapping in bigendian mode)
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We're weaning the core code off handing cpumask's around on-stack.
This introduces arch_send_call_function_ipi_mask(), and by defining
it, the old arch_send_call_function_ipi is defined by the core code.
We also take the chance to wean the implementations off the
obsolescent for_each_cpu_mask(): making send_ipi_mask take the pointer
seemed the most natural way to ensure all implementations used
for_each_cpu.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (34 commits)
time: Prevent 32 bit overflow with set_normalized_timespec()
clocksource: Delay clocksource down rating to late boot
clocksource: clocksource_select must be called with mutex locked
clocksource: Resolve cpu hotplug dead lock with TSC unstable, fix crash
timers: Drop a function prototype
clocksource: Resolve cpu hotplug dead lock with TSC unstable
timer.c: Fix S/390 comments
timekeeping: Fix invalid getboottime() value
timekeeping: Fix up read_persistent_clock() breakage on sh
timekeeping: Increase granularity of read_persistent_clock(), build fix
time: Introduce CLOCK_REALTIME_COARSE
x86: Do not unregister PIT clocksource on PIT oneshot setup/shutdown
clocksource: Avoid clocksource watchdog circular locking dependency
clocksource: Protect the watchdog rating changes with clocksource_mutex
clocksource: Call clocksource_change_rating() outside of watchdog_lock
timekeeping: Introduce read_boot_clock
timekeeping: Increase granularity of read_persistent_clock()
timekeeping: Update clocksource with stop_machine
timekeeping: Add timekeeper read_clock helper functions
timekeeping: Move NTP adjusted clock multiplier to struct timekeeper
...
Fix trivial conflict due to MIPS lemote -> loongson renaming.
The persistent clock of some architectures (e.g. s390) have a
better granularity than seconds. To reduce the delta between the
host clock and the guest clock in a virtualized system change the
read_persistent_clock function to return a struct timespec.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134811.013873340@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit fc03bc1715ca0ad4ccfe97aab16bcc9e7129c1a4 breaks when SMTC support
is enabled on Malta.
Signed-off-by: Raghu Gandham <raghu@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is to move the gcmp_probe call to before the use of and selection of
the smp_ops functions. This allows malta with 1004K to work.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of the CMP support was added before, this mostly correct compile
problems but adds a platform specific translation for the interrupt number
based on cpu number.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This takes the current IPI interrupt assignment from the fix number of 4
to the number of CPUs defined in the system.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some of the were relying into smp.h being dragged in by another header
which of course is fragile. <asm/cpu-info.h> uses smp_processor_id()
only in macros and including smp.h there leads to an include loop, so
don't change cpu-info.h.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
according to Ingo, change set_affinity() in irq_chip should return int,
because that way we can handle failure cases in a much cleaner way, in
the genirq layer.
v2: fix two typos
[ Impact: extend API ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The variable `mips_revision_corid' is needlessly defined global in
arch/mips/mti-malta/malta-init.c, and this patch makes it static.
Build-tested with malta_defconfig.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Impact: cleanup, update to new cpumask API
Irq_desc.affinity and irq_desc.pending_mask are now cpumask_var_t's
so access to them should be using the new cpumask API.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
