The driver PM resume assumes that the IP is still powered up and the
all the register contents are not disturbed when it comes out of low
power suspend case. This assumption is wrong, basically the driver
should not consider any state of registers after it comes out of low
power. However driver can keep the part of the IP powered up if its a
wake up source. But it can not assume the register state of the IP. Also
its possible that SOC glue layer can take the power off the IP if its
not wake-up source to reduce the power consumption.
This patch re initializes hardware by calling stmmac_hw_setup function in
resume case.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch promotes stmmac_mdio_reset function from static to
non-static, so that power management functions can decide to reset if
the IP comes out from lowe power state specially hibernation cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves hardware setup part of the code in stmmac_open to a new
function stmmac_hw_setup, the reason for doing this is to make hw
initialization independent function so that PM functions can re-use it to
re-initialize the IP after returning from low power state.
This will also avoid code duplication across stmmac_resume/restore and
stmmac_open.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves dma resource allocation to a new function
alloc_dma_desc_resources, the reason for moving this to a new function
is to keep the memory allocations in a separate function. One more reason
it to get suspend and hibernation cases working without releasing and
allocating these resources during suspend-resume and freeze-restore
cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes gpio_free for reset line of the phy, driver stores
the gpio number in its private data-structure to use in future. As the
driver uses this pin in future this pin should not be freed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to "max-speed" property which is a standard
Ethernet device tree property. max-speed specifies maximum speed
(specified in megabits per second) supported the device.
Depending on the clocking schemes some of the boards can only support
few link speeds, so having a way to limit the link speed in the mac
driver would allow such setups to work reliably.
Without this patch there is no way to tell the driver to limit the
link speed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function return parameter is not used in mvneta_tx_done_gbe(),
where the function is called. This patch makes the function return
void.
Reviewed-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta_tx_done_gbe() return value and third parameter are no more
used. This patch changes the function prototype and removes a useless
variable where the function is called.
Reviewed-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped. We set the limit to 256 bytes which seems to give good results both
on the XP-GP board and on the AX3/4.
The Rx small packet rate increased by 16.4% doing this, from 486kpps to
573kpps. It is worth noting that even the call to the function
dma_sync_single_range_for_cpu() is expensive (300 ns) although less
than dma_unmap_single(). Without it, the packet rate raises to 711kpps
(+24% more). Thus on systems where coherency from device to CPU is
guaranteed by a snoop control unit, this patch should provide even more
gains, and probably rx_copybreak could be increased.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of build_skb() to allocate frags on the RX path. When frag size
is lower than a page size, we can use netdev_alloc_frag(), and we fall back
to kmalloc() for larger sizes. The frag size is stored into the mvneta_port
struct. The alloc/free functions check the frag size to decide what alloc/
free method to use. MTU changes are safe because the MTU change function
stops the device and clears the queues before applying the change.
With this patch, I observed a reproducible 2% performance improvement on
HTTP-based benchmarks, and 5% on small packet RX rate.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the mvneta driver tries to prefetch the current Rx
descriptor during read. Tests have shown that prefetching the
next one instead increases general performance by about 1% on
HTTP traffic.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
At several places, we already know the value of the rx status but
we call functions which dereference the pointer again to get it
and don't need the descriptor for anything else. Simplify this
task by replacing the rx desc pointer by the status word itself.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make mvneta_rxq_fill() use mvneta_rx_refill() instead of using
duplicate code.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mvneta_txq_bufs_free() calls mvneta_tx_done_policy() with
a non-null cause to retrieve the pointer to the next queue to process.
There are useless tests on the return queue number and on the pointer,
all of which are well defined within a known limited set. This code
path is fast, although not critical. Removing 3 tests here that the
compiler could not optimize (verified) is always desirable.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the mvneta driver doesn't handle Tx IRQ, and relies on two
mechanisms to flush Tx descriptors : a flush at the end of mvneta_tx()
and a timer. If a burst of packets is emitted faster than the device
can send them, then the queue is stopped until next wake-up of the
timer 10ms later. This causes jerky output traffic with bursts and
pauses, making it difficult to reach line rate with very few streams.
A test on UDP traffic shows that it's not possible to go beyond 134
Mbps / 12 kpps of outgoing traffic with 1500-bytes IP packets. Routed
traffic tends to observe pauses as well if the traffic is bursty,
making it even burstier after the wake-up.
It seems that this feature was inherited from the original driver but
nothing there mentions any reason for not using the interrupt instead,
which the chip supports.
Thus, this patch enables Tx interrupts and removes the timer. It does
the two at once because it's not really possible to make the two
mechanisms coexist, so a split patch doesn't make sense.
First tests performed on a Mirabox (Armada 370) show that less CPU
seems to be used when sending traffic. One reason might be that we now
call the mvneta_tx_done_gbe() with a mask indicating which queues have
been done instead of looping over all of them.
The same UDP test above now happily reaches 987 Mbps / 87.7 kpps.
Single-stream TCP traffic can now more easily reach line rate. HTTP
transfers of 1 MB objects over a single connection went from 730 to
840 Mbps. It is even possible to go significantly higher (>900 Mbps)
by tweaking tcp_tso_win_divisor.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Arnaud Ebalard <arno@natisbad.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell has not published the chip's datasheet yet, so it's very hard
to find the relevant bits to manipulate to change the IRQ behaviour.
Fortunately, these bits are described in the proprietary LSP patch set
which is publicly available here :
http://www.plugcomputer.org/downloads/mirabox/
So let's put them back in the driver in order to reduce the burden of
current and future maintenance.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a queue timeout is reported, we can oops because of some
schedules while the caller is atomic, as shown below :
mvneta d0070000.ethernet eth0: tx timeout
BUG: scheduling while atomic: bash/1528/0x00000100
Modules linked in: slhttp_ethdiv(C) [last unloaded: slhttp_ethdiv]
CPU: 2 PID: 1528 Comm: bash Tainted: G WC 3.13.0-rc4-mvebu-nf #180
[<c0011bd9>] (unwind_backtrace+0x1/0x98) from [<c000f1ab>] (show_stack+0xb/0xc)
[<c000f1ab>] (show_stack+0xb/0xc) from [<c02ad323>] (dump_stack+0x4f/0x64)
[<c02ad323>] (dump_stack+0x4f/0x64) from [<c02abe67>] (__schedule_bug+0x37/0x4c)
[<c02abe67>] (__schedule_bug+0x37/0x4c) from [<c02ae261>] (__schedule+0x325/0x3ec)
[<c02ae261>] (__schedule+0x325/0x3ec) from [<c02adb97>] (schedule_timeout+0xb7/0x118)
[<c02adb97>] (schedule_timeout+0xb7/0x118) from [<c0020a67>] (msleep+0xf/0x14)
[<c0020a67>] (msleep+0xf/0x14) from [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194)
[<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) from [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24)
[<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) from [<c024afc7>] (dev_watchdog+0x18b/0x1c4)
[<c024afc7>] (dev_watchdog+0x18b/0x1c4) from [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c)
[<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) from [<c0020cad>] (run_timer_softirq+0x115/0x170)
[<c0020cad>] (run_timer_softirq+0x115/0x170) from [<c001ccb9>] (__do_softirq+0xbd/0x1a8)
[<c001ccb9>] (__do_softirq+0xbd/0x1a8) from [<c001cfad>] (irq_exit+0x61/0x98)
[<c001cfad>] (irq_exit+0x61/0x98) from [<c000d4bf>] (handle_IRQ+0x27/0x60)
[<c000d4bf>] (handle_IRQ+0x27/0x60) from [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8)
[<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) from [<c000fba9>] (__irq_usr+0x49/0x60)
Ben Hutchings attempted to propose a better fix consisting in using a
scheduled work for this, but while it fixed this panic, it caused other
random freezes and panics proving that the reset sequence in the driver
is unreliable and that additional fixes should be investigated.
When sending multiple streams over a link limited to 100 Mbps, Tx timeouts
happen from time to time, and the driver correctly recovers only when the
function is disabled.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stats writers are mvneta_rx() and mvneta_tx(). They don't lock anything
when they update the stats, and as a result, it randomly happens that
the stats freeze on SMP if two updates happen during stats retrieval.
This is very easily reproducible by starting two HTTP servers and binding
each of them to a different CPU, then consulting /proc/net/dev in loops
during transfers, the interface should immediately lock up. This issue
also randomly happens upon link state changes during transfers, because
the stats are collected in this situation, but it takes more attempts to
reproduce it.
The comments in netdevice.h suggest using per_cpu stats instead to get
rid of this issue.
This patch implements this. It merges both rx_stats and tx_stats into
a single "stats" member with a single syncp. Both mvneta_rx() and
mvneta_rx() now only update the a single CPU's counters.
In turn, mvneta_get_stats64() does the summing by iterating over all CPUs
to get their respective stats.
With this change, stats are still correct and no more lockup is encountered.
Note that this bug was present since the first import of the mvneta
driver. It might make sense to backport it to some stable trees. If
so, it depends on "d33dc73 net: mvneta: increase the 64-bit rx/tx stats
out of the hot path".
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Better count packets and bytes in the stack and on 32 bit then
accumulate them at the end for once. This saves two memory writes
and two memory barriers per packet. The incoming packet rate was
increased by 4.7% on the Openblocks AX3 thanks to this.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx head write-back registers are not cleared during an FLR or VF reset.
As a result a configuration that had head write-back enabled can leave the
registers set after the driver is unloaded. If the next driver loaded doesn't
use the write-back registers this can lead to a bad configuration where
head write-back is enabled, but the driver didn't request it.
To avoid this situation the PF should be resetting the Tx head write-back
registers when the VF requests a reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the QDE bits are set for a VF before the Rx
queues are enabled. As such we avoid head of line blocking in the event
that the VF stops cleaning Rx descriptors for whatever reason.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c | 14 ++++++++++++++
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 7 ++++---
2 files changed, 18 insertions(+), 3 deletions(-)
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans-up wake-on-lan code in the following ways:
1) Removes some driver hacks in be_cmd_get_acpi_wol_cap() that were based
on incorrect assumptions.
2) Uses the adapter->wol_en and wol_cap variables for checking if WoL
is supported and enabled on an interface instead of referring to the
exclusion list via the macro be_is_wol_supported()
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of NTKW_MAC_QUERY cmd has been deprecated for Skyhawk-R.
Replace the last remaining usage in be_vfs_mac_query() routine.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead, use the tail of the RXQ to pick the associated RXQ entry
This fix is required in preparation for supporting RXQ lengths greater than 1K.
For such queues, the frag index in the RX-compl entry is not valid as it is only a 10 bit entry not capable of addressing RXQs longer than 1K.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As be2net is used even by the 40Gbps Skyhawk-R chip
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier commit (f25b119c "Fix error messages while driver load for VFs")
incorrectly set the adapter->cmd_privileges value for VFs (in a
multi-channel config) to MAX_PRIVILEGES. This causes FW cmd failures
and avoidable error logs when certian cmds are issued by a VF.
Also, move the multi-channel hack to be_cmds.c inside
be_cmd_get_fn_privileges() routine.
Fixes: f25b119c "Fix error messages while driver load for VFs"
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ndo_set_mac_addr() call may be issued for a mac-addr that is already
active on an interface. If so, silently ignore the request. Sending such
a request to the FW, causes a "mac collision" error. The error is harmless
but is avoidable noise in the kernel log.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk-R FW does not support SET/GET_EXT_FAT_CAPABILITIES cmds via which
FW logging level can be controlled. Also, the hack used in BE3 to control
FW logging level via the ethtool interface is not needed in Skyhawk-R.
This patch also cleans up this code by moving be_set/get_fw_log_level()
routines to be_cmds.c where they belong.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
remove new line
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the GET_HSW_CONFIG cmd, the "pport" field must be set only while
querying the switch mode. When the "pport" field is set, the
"interface_id" field must be set to the port number, otherwise, it
must be set to adapter->if_handle.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this cmd is used only for Lancer.
MCC_CREATE_EXT_V1 supports larger CQ-ids and additional event codes for the
async_event_bitmap field.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO requires VLANs to be removed before aggregation can occur.
The Synopsys EMAC does not strip VLAN tags so this must be
done by the driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix new sparse warning about function declared static.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `lpc32xx_adc_probe':
drivers/staging/iio/adc/lpc32xx_adc.c:149: undefined reference to `devm_ioremap'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `goldfish_battery_probe':
drivers/power/goldfish_battery.c:181: undefined reference to `devm_ioremap'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `orion_mdio_probe':
drivers/net/ethernet/marvell/mvmdio.c:228: undefined reference to `devm_ioremap'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `exynos_mipi_video_phy_probe':
drivers/phy/phy-exynos-mipi-video.c:130: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/staging/iio/adc/spear_adc.c: In function ‘spear_adc_probe’:
drivers/staging/iio/adc/spear_adc.c:393:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/staging/dgap/dgap_driver.c: In function ‘dgap_cleanup_board’:
drivers/staging/dgap/dgap_driver.c:457:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
drivers/staging/dgap/dgap_driver.c: In function ‘dgap_do_remap’:
drivers/staging/dgap/dgap_driver.c:694:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/ptp/ptp_pch.c: In function ‘pch_remove’:
drivers/ptp/ptp_pch.c:571:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
drivers/ptp/ptp_pch.c: In function ‘pch_probe’:
drivers/ptp/ptp_pch.c:621:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce functions to enable and disable bridgeport address
notification feature, sysfs attributes for access to these
functions from userspace, and udev events emitted when a host
joins or exits a bridgeport-enabled HiperSocket channel.
Signed-off-by: Eugene Crosser <eugene.crosser@ru.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function for the "Perform network-subchannel operation"
CHSC command with operation code "bridgeport information",
and bit definitions for "characteristics" pertaning to this command.
Signed-off-by: Eugene Crosser <eugene.crosser@ru.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce functions to assign roles and check state of bridgeport-capable
HiperSocket devices, and sysfs attributes providing access to these
functions from userspace. Introduce udev events emitted when the state
of a bridgeport device changes.
Signed-off-by: Eugene Crosser <eugene.crosser@ru.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes unhandled register write in gianfar_ethtool.c.
Fixes following endianess related functional issues,
reported by sparse as well, i.e.:
gianfar_ethtool.c:1058:33: warning:
incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] [usertype] value
got restricted __be32 [usertype] ip4src
gianfar_ethtool.c:1164:33: warning:
restricted __be16 degrades to integer
gianfar_ethtool.c:1669:32: warning:
invalid assignment: ^=
left side has type restricted __be16
right side has type int
Solves all the sparse warnings for mixig normal pointers
with __iomem pointers for gianfar_ptp.c, i.e.:
gianfar_ptp.c:163:32: warning:
incorrect type in argument 1 (different address spaces)
expected unsigned int [noderef] <asn:2>*addr
got unsigned int *<noident>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete a variable that is at most only assigned to a constant, but never
used otherwise. In this code, it is the variable result that is used for
the return code, not rc.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
identifier i;
constant c;
@@
-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
On port VLAN deletion the list of MAC filters for the virtual function (VF)
VSI were all deleted. Let's keep them around, they come in handy for keeping
the VF functional.
Change-Id: I335e760392f274dc8b8b40efcb708f65b49d7973
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e Physical Function (PF) driver will allow the
Virtual Function (VF) driver to configure its own VLAN filters if no port
VLAN filter has been configured. This leads to the possibility of the
administrator setting a port VLAN filter for the VF after the VF has already
configured its own VLAN filters. This leads to a conflict that can only be
resolved by reloading the VF driver. When the conflicting administrative
command is detected in setting the port VLAN then log a message indicating to
the system administrator that he must now reload the VF driver for the new
port VLAN settings to take effect.
Change-Id: I8de73b885d944a043aff32226297e4249862bcad
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should use vxlan_dellink() handler in vxlan_exit_net(), since
i) we're not in fast-path and we should be consistent in dismantle
just as we would remove a device through rtnl ops, and more
importantly, ii) in case future code will kfree() memory in
vxlan_dellink(), we would leak it right here unnoticed. Therefore,
do not only half of the cleanup work, but make it properly.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
