These flags represent the state of the VF at various times. Do not
spell them as _STAT_ which can be confusing to readers who may think
these refer to statistics.
Change-ID: I6bc092cd472e8276896a1fd7498aced2084312df
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there are a lot of active VFs, it can take multiple seconds to
finish resetting all of them during certain flows., which can cause some
VFs to fail to wait long enough for the reset to occur. The user might
see messages like "Never saw reset" or "Reset never finished" and the VF
driver will stop functioning properly.
The naive solution would be to simply increase the wait timer. We can
get much more clever. Notice that i40e_reset_vf is run in a serialized
fashion, and includes lots of delays.
There are two prominent delays which take most of the time. First, when
we begin resetting VFs, we have multiple 10ms delays which accrue
because we reset each VF in a serial fashion. These delays accumulate to
almost 4 seconds when handling the maximum number of VFs (128).
Secondly, there is a massive 50ms delay for each time we disable queues
on a VSI. This delay is necessary to allow HW to finish disabling queues
before we restore functionality. However, just like with the first case,
we are paying the cost for each VF, rather than disabling all VFs and
waiting once.
Both of these can be fixed, but required some previous refactoring to
handle the special case. First, we will need the
i40e_vsi_wait_queues_disabled function which was previously DCB
specific. Second, we will need to implement our own
i40e_vsi_stop_rings_no_wait function which will handle the stopping of
rings without the delays.
Finally, implement an i40e_reset_all_vfs function, which will first
start the reset of all VFs, and pay the wait cost all at once, rather
than serially waiting for each VF before we start processing then next
one. After the VF has been reset, we'll disable all the VF queues, and
then wait for them to disable. Again, we'll organize the flow such that
we pay the wait cost only once.
Finally, after we've disabled queues we'll go ahead and begin restoring
VF functionality. The result is reducing the wait time by a large factor
and ensuring that VFs do not timeout when waiting in the VF driver.
Change-ID: Ia6e8cf8d98131b78aec89db78afb8d905c9b12be
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch is going to want to re-use some of the code in
i40e_reset_vf, so lets break up the beginning and ending parts into
their own helper functions. The first function will be used to
initialize the reset on a VF, while the second function will be used to
finalize the reset and restore functionality.
Change-ID: I48df808b8bf09de3c2ed8c521f57b3f0ab9e5907
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a capability negotiation between VF and PF using ENCAP/
ENCAP_CSUM offload flags in order for the VF to support outer checksum
and TSO offloads for encapsulated packets. These capabilities were assumed
by default and enabled in current hardware. Going forward, these features
needs to be negotiated with PF before advertising to the stack.
Additionally, strip out the mac.type checks for X722 since outer checksums
are enabled based on the ENCAP_CSUM offload negotiation flag and maintain
consistency between drivers in how the features are configured.
Change-ID: Ie380a6f57eca557a2bb575b66b12fae36d308920
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Alan Brady <alan.brady@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
First, this patch eliminates IOMMU DMAR Faults caused by VF hardware.
This is done by enabling VF hardware only after VSI resources are
freed. Otherwise, hardware could DMA into memory that is (or just has
been) being freed.
Then, the VF driver is activated only after VSI resources have been
reallocated. That's because the VF driver can request resources
immediately after it's activated. So they need to be ready at that
point.
The second race condition happens when the OS initiates a VF reset,
and then before it's finished modifies VF's settings by changing its
MAC, VLAN ID, bandwidth allocation, anti-spoof checking, etc. These
functions needed to be blocked while VF is undergoing reset. Otherwise,
they could operate on data structures that had just been freed or not
yet fully initialized.
Change-ID: I43ba5a7ae2c9a1cce3911611ffc4598ae33ae3ff
Signed-off-by: Robert Konklewski <robertx.konklewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our original filter limit of 8 was based on behavior that we saw from
Linux VMs. Now we're running Other Operating Systems under KVM and we
see that they commonly use more MAC filters. Since it seems weird to
require people to enable trusted VFs just to boot their OS, bump the
number of filters allowed by default.
Change-ID: I76b2dcb2ad6017e39231ad3096c3fb6f065eef5e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue that RSS offloading only works on PF0 by
using the direct register writing of the hash keys for the VFs instead
of using the admin queue command to do so.
Change-ID: Ia02cda7dbaa23def342e8786097a2c03db6f580b
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(KISS is Keep It Simple, Stupid. Or is it?)
The client interface vastly overengineered for what it needs to do.
It was originally designed to support multiple clients on multiple
netdevs, possibly even with multiple drivers. None of this happened,
and now we know that there will only ever be one client for i40e
(i40iw) and one for i40evf (i40iwvf). So, time for some KISS. Since
i40e and i40evf are a Dynasty, we'll simplify this one to match the
VF interface.
First, be a Destroyer and remove all of the lists and locks required
to support multiple clients. Keep one static around to keep track of
one client, and track the client instances for each netdev in the
driver's pf (or adapter) struct. Now it's Almost Human.
Since we already know the client type is iWarp, get rid of any checks
for this. Same for VSI type - it's always going to be the same type,
so it's just a Parasite.
While we're at it, fix up some comments. This makes the function
headers actually match the functions.
These changes reduce code complexity, simplify maintenance,
squash some lurking timing bugs, and allow us to Rock and Roll All
Nite.
Change-ID: I1ea79948ad73b8685272451440a34507f9a9012e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix typos and add the following to the scripts/spelling.txt:
varible||variable
While we are here, tidy up the comment blocks that fit in a single line
for drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c and
net/sctp/transport.c.
Link: http://lkml.kernel.org/r/1481573103-11329-11-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of using i40e_add_filter or i40e_del_filter directly, when
adding a MAC address, we should normally be using i40e_add_mac_filter or
i40e_del_mac_filter. These functions correctly handle the various cases
of VLAN mode or PVID settings. This ensures consistency and avoids the
issues that can occur with the recent addition of a WARN_ON() in
i40e_sync_vsi_filters.
Change-ID: I7fe62db063391fdd1180b2d6a6a3c5ab4307eeee
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use __i40e_del_filter instead of using i40e_del_filter() which will
avoid doing an additional search to delete a filter we already have the
pointer for.
Change-ID: Iea5a7e3cafbf8c682ed9d3b6c69cf5ff53f44daf
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These functions purpose is to add a new MAC filter correctly, whether
we're using VLANs or not. Their goal is to ensure that all active VLANs
get the new MAC filter. Rename them so that their intent is clear. They
function correctly regardless of whether we have any active VLANs or
only have I40E_VLAN_ANY filters. The new names convey how they function
in a more clear manner.
Change-ID: Iec1961f968c0223a7132724a74e26a665750b107
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fold the check for determining when to call i40e_put_mac_in_vlan directly
into the function so that we don't need to decide which function to use
ahead of time. This allows us to just call i40e_put_mac_in_vlan directly
without having to check ahead of time.
Change-ID: Ifff526940748ac14b8418be5df5a149502eed137
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current flow for adding or updating the PVID for a VF uses
i40e_vsi_add_vlan and i40e_vsi_kill_vlan which each take, then release
the hash lock. In addition the two functions also must take special care
that they do not perform VLAN mode changes as this will make the code in
i40e_ndo_set_vf_port_vlan behave incorrectly.
Fix these issues by using the new helper functions i40e_add_vlan_all_mac
and i40e_rm_vlan_all_mac which expect the hash lock to already be taken.
Additionally these functions do not perform any state updates in regards
to VLAN mode, so they are safe to use in the PVID update flow.
It should be noted that we don't need the VLAN mode update code here,
because there are only a few flows here.
(a) we're adding a new PVID
In this case, if we already had VLAN filters the VSI is knocked
offline so we don't need to worry about pre-existing VLAN filters
(b) we're replacing an existing PVID
In this case, we can't have any VLAN filters except those with the old
PVID which we already take care of manually.
(c) we're removing an existing PVID
Similarly to above, we can't have any existing VLAN filters except
those with the old PVID which we already take care of correctly.
Because of this, we do not need (or even want) the special accounting
done in i40e_vsi_add_vlan, so use of the helpers is a saner alternative.
It also opens the door for a future patch which will refactor the flow
of i40e_vsi_add_vlan now that it is not needed in this function.
Change-ID: Ia841f63da94e12b106f41cf7d28ce8ce92f2ad99
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for 25G devices - defines and data structures.
One tricky part here is that the firmware support for these
Devices introduces a mismatch between the PHY type enum and
the bitfields for the phy types.
This change creates a macro and uses it to increment the 25G
PHY values when creating 25G bitfields.
Change-ID: I69b24d837d44cf9220bf5cb8dd46c5be89ce490b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous workaround added to ensure receipt of all broadcast frames
incorrectly set the broadcast promiscuous mode unconditionally
regardless of active VLAN status.
Replace this partial workaround with a complete solution that sets the
broadcast promiscuous filters in i40e_sync_vsi_filters. This new method
sets the promiscuous mode based on when broadcast filters are added or
removed.
I40E_VLAN_ANY will request a broadcast filter for all VLANs, (as we're
in untagged mode) while a broadcast filter on a specific VLAN will only
request broadcast for that VLAN.
Thus, we restore addition of broadcast filter to the array, but we add
special handling for these such that they enable the broadcast
promiscuous mode instead of being sent as regular filters.
The end result is that we will correctly receive all broadcast packets
(even those with a *source* address equal to the broadcast address) but
will not receive packets for which we don't have an active VLAN filter.
Change-ID: I7d0585c5cec1a5bf55bf533b42e5e817d5db6a2d
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This label is unnecessary, as are jumping to a block that checks aq_ret
and then immediately skipping it and returning. So just jump straight to
the error_param and remove this unnecessary label.
Also use goto error_param even in the last check for style consistency.
Change-ID: If487c7d10c4048e37c594e5eca167693aaed45f6
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removed some of unnecessary if statements and unreachable code found by
static code analysis tool.
The return value of i40e_vsi_control_rings(..., false) is always 0. So,
test for non-zero will never be true. The function has been split into
"int i40e_vsi_start_rings()" and "void i40e_vsi_stop_rings()" for better
understanding.
Similarly, the function i40e_vsi_kill_vlan() never fails. So, checking
for return value is also unnecessary. Function definition changed to void.
The i40e_loopback_test() function is not implemented. The function and
all references to loopback testing were removed.
Change-ID: Id45cf66f6689ce2bc4e887de13f073e30e8431bd
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a VF is reset, it gets a new VSI, so all of its MAC filters go
away. Correctly set the number of filters to 0 when freeing VF
resources. This corrects a problem with failure to add filters when the
VF driver is reloaded.
Change-ID: I2acbecf734287b67473bb225293e14b5096acbef
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the mac_filter_list with a static size hash table of 8bits. The
primary advantage of this is a decrease in latency of operations related
to searching for specific MAC filters, including .set_rx_mode. Using
a linked list resulted in several locations which were O(n^2). Using
a hash table should give us latency growth closer to O(n*log(n)).
Change-ID: I5330bd04053b880e670210933e35830b95948ebb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Originally the is_vf and is_netdev fields were added in order to
distinguish between VF and netdev filters in a single VSI. However, it
can be noted that we use separate VSI for SRIOV VFs and for netdev VSI.
Thus, since a single VSI should only ever have one type of filter, we
can simply remove the checks and remove the typing.
In a similar fashion, we can note that the only remaining way to get
multiple filters of a single type is through a debug command that was
added to debugfs. This command is useless in practice, and results in
causing bugs if we keep counter tracking but lose the is_vf and
is_netdev protections as desired above.
Since the only time we'd actually have a counter value besides 0 and
1 is through use of this debugfs hook, we can remove this unnecessary
command, and the entire counter logic it required.
We vastly simplify mac filters by removing
(a) the distinction between VF and netdev filters
(b) counting logic
(c) the ability to add and remove filters bypassing the stack via debugfs
Change-ID: Idf916dd2a1159b1188ddbab5bef6b85ea6bf27d9
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Trival fix, dev_err message is missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-09-22
This series contains updates to i40e and i40evf only.
Sridhar fixes link state event handling by updating the carrier and
starts/stops the Tx queues based on the link state notification from PF.
Brady fixes an issue where a user defined RSS hash key was not being
set because a user defined indirection table is not supplied when changing
the hash key, so if an indirection table is not supplied now, then a
default one is created and the hash key is correctly set. Also fixed
an issue where when NPAR was enabled, we were still using pf->mac_seid
to perform the dump port query. Instead, go through the VSI to determine
the correct ID to use in either case.
Mitch provides one fix where a conditional return code was reversed, so
he does a "switheroo" to fix the issue.
Carolyn has two fixes, first fixes an issue in the virt channel code,
where a return code was not checked for NULL when applicable. Second,
fixes an issue where we were byte swapping the port parameter, then
byte swapping it again in function execution.
Colin Ian King fixes a potential NULL pointer dereference.
Bimmy changes up i40evf_up_complete() to be void since it always returns
success anyways, which allows cleaning up of code which checked the
return code from this function.
Alex fixed an issue where the driver was incorrectly assuming that we
would always be pulling no more than 1 descriptor from each fragment.
So to correct this, we just need to make certain to test all the way to
the end of the fragments as it is possible for us to span 2 descriptors
in the block before us so we need to guarantee that even the last 6
descriptors have enough data to fill a full frame.
v2: dropped patches 1-3, 10 and 12 from the original series since Or
Gerlitz pointed out several areas of improvement in the implementation
of the VF Port representor netdev. Sridhar is re-working the series
for later submission.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue in the virt channel code, where a return
from i40e_find_vsi_from_id was not checked for NULL when applicable.
Without this patch, there is a risk for panic and static analysis
tools complain. This patch fixes the problem by adding the check
and adding an additional input check for similar reasons.
Change-ID: I7e9be88eb7a3addb50eadc451c8336d9e06f5394
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This conditional is backward, so the driver responds back to the VF with
the wrong opcode. Do the old switcheroo to fix this.
Change-ID: I384035b0fef8a3881c176de4b4672009b3400b25
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enables
ip -d l
to indicate if trust is on or off for VFs.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we allocate memory, we must free it. It's simple courtesy.
Change-ID: Id007294096fb53344f1a8b9a0f78eddf9853c5d6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF goes through reset path during VF creation which happens to also
have notification of VF reset to client. Adding conditional check to
avoid wrongly notifying VF reset during VF creation.
Also changing the call order of VF enable, calling it after VF creation
rather than before.
Change-ID: I96eabd99deae746a2f0fc465194c886f196178ce
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we do a reset, all the VLAN filters get added again. Therefore we also
want to reset the VLAN count to 0 or we quickly run out of filters.
Change-ID: I459f26851e22204dc8b8999928ad87cde8170119
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that VF RSS is configured by the PF driver, it needs to set the RSS
Hash Enable registers by default. Without this, no packets will be
hashed and they'll all end up on queue 0.
Change-ID: I38e425f40ddb81e3b19a951cfbb939fa5b1123f1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that all VSIs are configured to receive broadcasts as default, we
don't need to add a filter. This eliminates an annoying but harmless
error message each time VFs are created or reset.
Change-ID: I4cd6339684df45b0d2722133eeb84c14fa93ea19
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If an untrusted VF attempts to configure promiscuous mode, log a message
pointing out its naughty behavior. But then, instead of returning an
error to the offender, just lie to it and say everything's OK. It will
continue on its way, thinking it's in promiscuous mode, but receiving no
packets except its own.
Change-ID: I63369215b1720f3c531eedfc06af86ff8c0e3dc8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.
The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.
For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.
Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP : off
LinkPolling : off
flow-director-atr : on
veb-stats : off
hw-atr-eviction : off
vf-true-promisc-support: off
to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on
At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic
Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Newly added code in i40e_vc_config_promiscuous_mode_msg() is indented
in a way that gcc rightly complains about:
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c: In function 'i40e_vc_config_promiscuous_mode_msg':
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:1543:4: error: this 'if' clause does not guard... [-Werror=misleading-indentation]
if (f->vlan >= 0 && f->vlan <= I40E_MAX_VLANID)
^~
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:1550:5: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the 'if'
aq_err = pf->hw.aq.asq_last_status;
From the context, it looks like the aq_err assignment was meant to be
inside of the conditional expression, so I'm adding the appropriate
curly braces now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5676a8b9cd ("i40e: Add VF promiscuous mode driver support")
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Some of the split related context set up code stays in
i40e_virtchnl_pf.c in case an older VF driver tries to load
and still wants to use packet split.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was all over the place using signed or unsigned types
for vf_id, when it should always be signed.
This fixes warnings of type unsafe comparisons from gcc with W=2.
Change-Id: I2cb681f83d0f68ca124d2e4131e4ac0d9f8a6b22
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have an uninitialized variable warning for valid_len for one case in
validate_vf_mesg. To fix this, just initialize it to 0 at the top of the
function and remove all of the now redundant assignments to 0 in the
individual cases.
Change-Id: Iacbd97f4c521ed8d662eef803a598d8707708cfd
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF is privileged/trusted it can do as it may please including
but not limited to hogging resources and playing unfair.
But if the VF is not privileged/trusted it still can add some number
(8) of MAC and VLAN addresses.
Other restrictions with respect to Port VLAN and normal VLAN still apply
to not privileged/trusted VF.
Change-Id: I3a9529201b184c8873e1ad2e300aff468c9e6296
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure a VF is not trusted/privileged until its explicitly
set for trust through the new NDO op interface.
Change-Id: I476385c290d2b4901d8fceb29de43546accdc499
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add necessary Linux Ethernet driver support for promiscuous mode
operation. Add a flag so the VF knows it is in promiscuous mode
and two state flags to discreetly track multicast and unicast
promiscuous states.
Change-Id: Ib2f2dc7a7582304fec90fc917ebb7ded21ba1de4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for configuring RSS on behalf of the VFs. This removes the
burden of dealing with different hardware interfaces from the VF
drivers, allowing for better future compatibility.
Change-ID: Icea75d3f37241ee8e447be5779e5abb53ddf04c0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VFs can request their queues to be set up into polling mode, rather
than interrupt mode, which works well for supporting things like DPDK,
but this should not be available when working in an multi-function
support device.
Change-ID: Id36792e4e7422db8f2033336507211f68f14ff6f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds hook to support changing a VF from not-trusted
to trusted and vice-versa. Fixed the wrappers and function prototype.
Changed the dmesg to reflex the current state better. This patch also
disables turning on/off trusted VF in MFP mode.
Change-ID: Ibcd910935c01f0be1f3fdd6d427230291ee92ebe
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch moves the HW flush routine to the end of the reset flow,
after the completion of writing to the device VFLR registers- the
benefit is to avoid problems in the passthrough routines.
Change-ID: Ieb56866f21895e6c1fc514b7328c3df79807a57c
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These conditions can happen any time VFs are enabled or disabled and are
not really indicative of fatal problems unless they happen continuously.
Lower the log level so that people don't get scared.
Change-ID: I1ceb4adbd10d03cbeed54d1f5b7f20d60328351d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the VFLR bit immediately after triggering a reset instead of
waiting until after cleanup is complete. Make sure to trigger a reset
every time, not just if the PF is up.
These changes fix a problem where VF resets would get lost by the PF,
preventing the VF driver from initializing.
Change-ID: I5945cf2884095b7b0554867c64df8617e71d9d29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This variable is vestigial, a remnant of the primordial code from which
this driver spawned. We can safely remove it.
Change-ID: I24e0fe338e7c7c50d27dc5515564f33caefbb93a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Minor correction in the comment to reflect the correct function name
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller