This comment is just plain false. VF drivers require MSI-X or they won't
get interrupts at all.
Change-ID: Iaea5e30b6926948aa834a3c506d9a9223d9e3e29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to print log messages when we encounter an out-of-memory
condition, as the allocator will do this for us. Also, remove a Tx hang
message that duplicates the one emitted by the netdev layer, and a
duplicate message in the watchdog.
Change-ID: If2056e6135fe248f66ea939778f9895660f4d189
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. There is no ixgbe_watchdog_task function in the driver, so change
the comment to the correct function name, i40e_watchdog_subtask.
2. Remove num_msix_entries from interrupt set_up routine
because it is never used.
3. Remove some TBD comments that are not needed.
Change-ID: I37697a04007074b797f85fd83d626672e4df1ad1
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove use of registers no longer supported.
Change-ID: I9d27399091cea78a926489d94f958edd762f5a20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As reported by Eric Dumazet, the driver is not masking the right
bits in the receive descriptor before it starts checking them.
This patch extends the mask to allow for the right bits to be
checked, and fixes the issue permanently via a define.
CC: Eric Dumazet <eric.dumazet@gmail.com>
Change-ID: I3274f7619057a950f468143e6d7e11b129f54655
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The include of asm/cputype.h breaks the powerpc build. This
include was accidentally left in from driver debugging and
can be removed.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>,
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 0.4.3 and i40evf to 0.9.27.
Change-ID: I4141e9f8615bdcfa3b1b5ecbc2ac62603a03b7ad
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use an extra state variable to keep track of when the IRQs are fully
set up. This keeps us from trying to unhook IRQs that already were
left unhooked in a failed reset recovery, e.g. when firmware is broken.
Change-ID: I073eb081e4ef8aedcbdf1ee0717c0ed64fa172f2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset recovery failed (e.g. firmware is broken), the HMC space won't
get set up. We don't need to try to delete it if it didn't get set up.
This stops some needless error messages when we already know we need to
just tear things down.
Change-ID: Iac600481765e20b136052b43a544e55d7870268b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver should print link messages like all the
other Intel Ethernet drivers.
Change-ID: Ia88bdb96794e17a3962fcea94db176de01f921f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the missing unicast, multicast, and broadcast stats for the port.
Change-ID: Ifc366d7b7745f70eaac9d00eeb0694eb9ec076a9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add VSI HW stats for unicast, multicast, and broadcast for Rx and Tx.
Stop printing the netdev multicast value because it doesn't include Tx
and would be confusing.
Change-ID: I08278b6657e7c838fd29a4a1f305f78fe1b150be
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The wait time was originally too optimistic and the resets were failing
after EMPR. This increases the loop count to wait considerably longer.
This won't delay the actual wait longer than really needed, just allows
us to poll more times as needed.
Change-ID: If7b96f55cc25b8d06cbbe8665259d250188c53d7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a function which indicates our intention to enable or disable a particular
Tx queue. Also add a function to notify the device's Tx unit that we're about
to enable or disable a Tx queue.
Change-ID: I6adf3cbb5bb3e3c984d1ec969e06577c19ef296d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
B0 Si blocks AQ registers when in Blank Flash mode - write is dropped,
read gives 0xDEADBEEF. Introduce a simple check for a correct value in one
of the AQ registers to be sure that AQ was configured correctly.
Without this check we get into an endless loop while trying to send
GetVersion AQ cmd.
Change-ID: I00102b8c5fa6c16d14289be677aafadf87f10f0d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Depending on the timing of what the PF driver is doing, it make take a
few tries before the VF driver is able to communicate with the PF driver
on init or reset recovery. In order to prevent confusion, make the most
common messages less scary by lowering them to a less terrifying log
level and indicate that the driver will retry.
Change-ID: I1ec22aa59a68f4469aabe14775a1bfc1ab4b7f2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver and hardware are not expected to work correctly
with revision_id 0 hardware. Don't prevent the user from
using it, but be sure to print a warning.
Change-ID: I3712d34752bfad458078a5f35dfd0aa0ae9fd20e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print the VEB statistics in the ethtool stats output.
Change-ID: Ic93d4c3922345c43e4cfd7f7e7a906844dd2f49f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VEB is created for the basic LAN device and its VSIs, we need to
set the tracking lan_veb index for later use.
Change-ID: I66bb74993bbda3621ca557437cb4b3517f9b315b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/xen-netback/netback.c
net/core/filter.c
A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.
A xen-netback bug fix overlapped the addition of multi-queue
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYSTEMPORT driver uses libphy to determine the carrier state, so
make sure we start with a carrier off until libphy has completed the
link training process.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment about how the hardware prepends 2bytes to align the IP
header on a 4-byte boundary was not correct, fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing an and comparison with status to check whether
RX_STATUS_OVFLOW is asserted or not in the per-packet status word, fix
that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our transmit locking scheme did not account for the TX ring full
interrupt. If a TX ring full interrupt fires while we are attempting to
transmit, we will cause a deadlock to occur. Fix this by making sure
that we properly disable interrupts while acquiring the spinlock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the initial platform driver for the AMD
10GbE device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/amd/hplance.h:
#define HPLANCE_MEMOFF 0x8000 /* struct lance_init_block */
#define HPLANCE_NVRAMOFF 0xC008 /* etheraddress as one *nibble* per byte */
The offset of RAM start is 0x8000, the offset of RAM end is 0xC008,
so the RAM size is 16392 bytes.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order of ram pages is 3, so the ram size is 2^3 * 4K = 32K.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the DM9000B, dm9000_msleep() is called during the dm9000_timeout()
routine. Since dm9000_timeout() holds the main spinlock through the
entire routine, mdelay() needs to be used rather than msleep().
Furthermore, the mutex_lock()/mutex_unlock() should be avoided so as to
not sleep with spinlocks held.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the DM9000A/DM9000B force the initial check of the link status. The
DM9000A/B has a link status changed event and this interrupt bit isn't
always set out of reset when a cable is plugged in. This results in the
driver not seeing the cable attached link status until the cable is
removed and plugged in again.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dm9000_interrupt() is already reading/clearing every set bit in
DM9000_ISR, this additional clear in dm9000_rx() (which is only called
by dm9000_interrupt()) is unnecessary and can be removed.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DM9000 uses level-triggered interrupts. Some systems (PXA270) only
support edge-triggered interrupts on GPIOs. Some changes are necessary
to ensure that interrupts are not triggered while the GPIO interrupt is
masked or we will miss the interrupt forever.
* Make some helper functions called dm9000_mask_interrupts() and
dm9000_unmask_interrupts() for readability.
* dm9000_init_dm9000(): ensure that this function always leaves interrupts
masked regardless of the state when it entered the function. This is
primarily to support the situation in dm9000_open where the logic used
to go:
dm9000_open()
dm9000_init_dm9000()
unmask interrupts
request_irq()
If an interrupt occurred between unmasking the interrupt and
requesting the irq, it would be missed forever as the edge event would
never be seen by the GPIO hardware in the PXA270. This allows us to
change the logic to:
dm9000_open()
dm9000_init_dm9000()
dm9000_mask_interrupts()
request_irq()
dm9000_unmask_interrupts()
* dm9000_timeout(), dm9000_drv_resume(): Add the missing
dm9000_unmask_interrupts() now required by the change above.
* dm9000_shutdown(): Use mask helper function
* dm9000_interrupt(): Use mask/unmask helper functions
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Change a hard-coded 0x3 to NCR_RST | NCR_MAC_LBK in dm9000_reset
* Every single place where dm9000_init_dm9000 was ran, a dm9000_reset
was called immediately before-hand. Bring dm9000_reset into
dm9000_init_dm9000.
* The following commit updated the dm9000_probe reset routine to use NCR_RST
| NCR_MAC_LBK:
6741f40 DM9000B: driver initialization upgrade
and a later commit added a bug-fix to always reset the chip twice:
09ee9f8 dm9000: Implement full reset of DM9000 network device
Unfortunately, since the changes in 6741f40 were made by replacing the
dm9000_probe dm9000_reset with the adjusted iow(), the changes in
09ee9f8 were not incorporated into the dm9000_probe reset.
Furthermore, it bypassed the requisite reset-delay causing some boards
to get at least one "read wrong id ..." dev_err message during
dm9000_probe.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DM9000 supports both active high interrupts and active low interrupts.
This is configured via the attached EEPROM. In the device-tree case, make sure
that the DM9000 driver passes the correct flags to request_irq.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Uninitialzed fields in mailbox command structure
caused commands to time out randomly due to garbage
values so initialize it to zero.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting David Miller:
"At the moment you call register_netdev() the device is visible, notifications
are sent to userspace, and userland tools can try to bring the interface up
and see the incorrect link state, before you do the netif_carrier_off().
Said another way, between the register_netdev() and netif_carrier_off() call,
userspace can see the device in an inconsistent state."
So call netif_carrier_off() prior to register_netdev().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple more statistics that the hardware offers but aren't part
of the standard netdev stats.
Change-ID: I201db2898f2c284aee3d9631470bc5edd349e9a5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rx_errors (GLV_REPC) and rx_missed (GLV_RMPC) were removed
from the chip design.
Change-ID: Ifdeb69c90feac64ec95c36d3d32c75e3a06de3b7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull the PF stat collection out of the VSI collection routine, and
add a unifying stats update routine to call the various stat collection
routines.
Change-ID: I224192455bb3a6e5dc0a426935e67dffc123e306
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves some common code in two places into a
small helper function, and corrects a bug in one of the
two places in the process.
Change-ID: If3bba7152b240f13a7881eb0e8a781655fa66ce7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Structure for VEB context added. Update macro for
transition from ms to GTIME (us) time units.
Change-ID: Ib3a19587b4cf355348655df8f60c6f37bb1497a3
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the PF driver only notifies the VFs for PF reset events.
Instead, notify the VFs for all types of resets, so they can attempt a
graceful reinit.
Change-ID: I03eb7afde25727198ef620f8b4e78bb667a11370
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40evf_set_ringparam was broken in several ways. First, it only changed
the size of the first ring, and second, changing the ring size would
often result in a panic because it would change the count before
deallocating resources, causing the driver to either free nonexistent
buffers, or leak leftover buffers.
Fix this by storing the descriptor count in the adapter structure, and
updating the count for each ring each time we allocate them. This
ensures that we always free the right size ring, and always end up with
the requested count when the device is (re)opened.
Change-ID: I298396cd3d452ba8509d9f2d33a93f25868a9a55
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware requires descriptors to be allocated in groups of 32.
Change-ID: I752ccc96769d1bd8d3018c004b8aeff464045bf2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was allowing the user to set larger size MTU
than the hardware was being configured to support.
The driver was already using VLAN_HLEN when setting the
hardware max receivable frame size, so just add it to the
netdev MTU set entry point as well.
Change-ID: Ie20e2a35d04f8c411253e255bea79ca69aaeaea3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused defines and macros for RX_LRO.
Change-ID: I8ca6715edfa62b56837417a1c4ff68c2345dab6e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We introduced this check in case this structure changed in the future,
the AQ definition is now mature enough that this check is no longer necessary.
Change-ID: Ic66321d0a08557dc9d8cb84029185352cb534330
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Register range, being subject to register diagnostic, can vary among
different NVMs. We will try to identify the full range and use it for
a register test. This is needed to avoid false test results. If we fail
to define the proper register range we will test only the first register
from that group.
Change-ID: Ieee7173c719733b61d3733177a94dc557eb7b3fd
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams